点群6mm一维六方准晶压电材料中含螺型位错的电弹性场分析

根据点群6mm一维六方准晶压电材料反平面问题的一般方程,得到其含螺型位错时应力场和电场的解析解。利用复变函数的方法,得出材料中裂纹与螺型位错在相互作用时的应力场解析表达式,所得到的解析解可以退化为已知材料的理论解。通过数值算例表明:离螺型位错越近,力场和电场值越小,反之越大。通过研究螺形位错与裂纹的相互作用为讨论一维六方准晶压电材料的裂纹顶端发射位错和裂纹钝化奠定了理论基础。     

一维六方准晶中平行螺型位错与有限长裂纹的相互作用

论文采用解析函数理论,利用Muskhelishvili著名的复变函数方法,给出了无限大一维六方准晶中多条平行螺型位错与有限长直裂纹相互作用的解析解,并得到了裂纹尖端的场强度因子和作用在位错上的像力.数值算例讨论了镜像力、场强度因子随位错位置的变化,及位错的位置与分布对广义应力场的影响.     

一维六方准晶压电材料中多缺陷的相互作用

基于准晶压电材料的基本方程,利用解析函数理论和复变方法,研究了一维六方准晶压电材料中多缺陷的相互作用问题,建立了多条平行位错以及它们与半无限裂纹相互作用的断裂力学模型,给出了一维六方准晶压电材料中n条平行位错相互作用的Peach Koehler公式和n条平行位错的等效作用点,得到了n条平行位错与半无限裂纹相互作用下电弹性场的解析解,数值算例给出了位错位置对裂纹面上应力的影响和位错Burgers矢量的大小对裂纹面上应力的影响,为讨论裂纹尖端的位错发射、位错屏蔽和裂纹钝化奠定了理论基础.这些结果均为本文首次给出,丰富和发展了经典弹性理论中的相应结果.     

一维六方准晶压电材料反平面Ⅲ型裂纹电塑性分析

论文基于一维六方准晶压电材料反平面问题的基本方程,对Ⅲ型裂纹的电塑性区进行分析.采用条带模型并假设在电塑性区的切应力保持为常数,得到了电塑性区大小的表达式.这种假设方式消除了电场和应力在裂纹尖端的奇异性,这与实际情况相符合,也为一维六方准晶压电材料的断裂分析提供了理论基础.     

含双周期裂纹的一维六方准晶电弹性全平面应变基本问题

针对电极化方向沿准周期方向的情况,讨论了周期平面内含双周期裂纹的一维六方准晶的电弹性全平面应变第一基本问题和第二基本问题。根据力的叠加原理,将三维的应力系统分解为线性独立的两组二维应力状态;运用复应力函数方法将弹性平衡状态的求解归结为求解正则型积分方程,并证明了其唯一可解性。结果表明:一维六方准晶双周期断裂问题在广义双周期边界条件下的力学解是存在并且唯一的。此结果为运用各种方法研究该基本问题的正确性和一致性提供了理论保证。     

压电双材料界面钝裂纹附近螺型位错的屏蔽效应与发射条件

研究了压电双材料界面钝裂纹附近螺型位错的屏蔽效应与发射条件.应用保角变换技术,得到了复势函数与应力场的封闭形式解,讨论了位错方位、双材料电弹常数及裂纹钝化程度对位错屏蔽效应和发射条件的影响.结果表明,Burgers矢量为正的螺型位错可以降低界面钝裂纹尖端的应力强度因子(屏蔽效应),屏蔽效应随位错方位角及位错与裂纹尖端距离的增大而减弱,压电双材料中螺型位错对裂纹的屏蔽效应强于相应弹性双材料中螺型位错对裂纹的屏蔽效应;位错发射所需的临界无穷远加载或电位移随位错方位角及裂纹钝化程度的增加而增大;最可能的位错发射角度为零度即位错最可能沿裂纹前方发射.论文解答的特殊情况与已有文献一致.     

层状压电半空间中的螺位错

研究了层状压电半空间中的螺位错与界面的相互作用,应用傅立叶变换的方法,推导了压电层和基体的弹性场和电场,并在此基础上给出了像力的表达式,分析了几何尺寸和材料的相对刚度对像力和界面应力的影响.结果表明:压电效应的存在可以改变位错与界面的相互作用机理;弹性常数的差异对界面应力有较大的影响.     

一维六方准晶压电材料中唇形裂纹反平面问题的解析解

本文在准晶压电材料基本方程的基础上,根据点群的对称性和一维六方准晶的线性压电效应,导出了一维六方准晶压电材料反平面问题的控制方程.利用复变函数的方法,通过引入适当的保角映射,研究了准晶压电材料中唇形裂纹的反平面问题,并利用Cauchy积分理论,得到在电不可通边界条件下的裂纹尖端场强度因子与机械应变能释放率的解析表达式.     

压电螺位错与含界面裂纹圆形涂层夹杂的干涉

研究位于基体或夹杂中任意点的压电螺型位错与含界面裂纹圆形涂层夹杂的电弹耦合干 涉问题. 运用复变函数方法,获得了基体,涂层和夹杂中复势函数的一般解答. 典型例 子给出了界面含有一条裂纹时,复势函数的精确级数形式解. 基于已获得的复势函数和广 义Peach-Koehler公式,计算了作用在位错上的像力. 讨论了裂纹几何条件,涂层厚度和材 料特性对位错平衡位置的影响规律. 结果表明,界面裂纹对涂层夹杂附近的位错运动有很大 的影响效应,含界面裂纹涂层夹杂对位错的捕获能力强于完整粘结情况;并发现界面裂纹长 度和涂层材料常数达到某一个临界值时可以改变像力的方向. 解答的特殊情形包含了以 往文献的几个结果.     

压电螺型位错和共线界面刚性线夹杂的干涉效应

研究了压电材料中压电螺型位错和共线界面导电刚性线夹杂的电弹干涉效应.运用复变函数解析延拓技术与奇性主部分析方法,获得了该问题的一般解答.作为算例,求出了界面含一条刚性线夹杂时两种压电介质区域广义应力函数的封闭形式解.导出了作用在位错上的像力和刚性线夹杂表面剪应力和电位移的解析表达式.讨论了界面刚性线长度,两种材料的剪切模量比和压电系数比对位错力和刚性线表面剪应力的影响规律.为进一步研究该类问题提供了一个基本解.     

Interaction between a screw dislocation and an elliptical hole with two asymmetrical cracks in a one-dimensional hexagonal quasicrystal with piezoelectric effect

The interaction between a screw dislocation and an elliptical hole with two asymmetrical cracks in a one-dimensional(1 D) hexagonal quasicrystal with piezoelectric effect is considered. A general formula of the generalized stress field, the field intensity factor, and the image force is derived, and the special cases are discussed. Several numerical examples are given to show the effects of the material properties and the dislocation position on the field intensity factors and the image forces.     

含直对称裂纹的一维六方压电准晶对SH波的散射Scattering of SH wave by a linear symmetric crack at one-dimensional piezoelectric hexagonal quasicrystals

利用积分变换技术,结合Copson方法,研究了含直线型对称裂纹的一维六方压电准晶对SH波的散射问题。通过求解对偶积分方程,得到声子场、相位子场应力、位移及电场电位移分量的解析解。定义了裂纹尖端应力强度因子及电位移强度因子,给出了电非渗透性条件下应力强度因子及电位移强度因子的解析解。此研究结果对压电准晶材料的工程应用有一定的理论价值。     

Electroelastic interaction between a piezoelectric screw dislocation and a circular inhomogeneity with interfacial cracks

A piezoelectric screw dislocation in the matrix interacting with a circular inhomogeneity with interfacial cracks under antiplane shear and in-plane electric loading at infinity was dealt with. Using complex variable method, a general solution to the problem was presented. For a typical case, the closed form expressions of complex potentials in the inhomogeneity and the matrix regions and derived explicitly when the interface containsthe electroelastic field intensity factors weresingle crack. The image force acting on the piezoelectric screw dislocation was calculated by using the perturbation technique and the generalized Peach-Koehler formula. As a result, numerical analysis and discussion show that the perturbation influence of the interfacial crack on the interaction effects of the dislocation and the inhomogeneity is significant which indicates the presence of the interfacial crack will change the interaction mechanism when the length of the crack goes up to a critical value. It is also shown that soft inhomogeneity can repel the dislocation due to their intrinsic electromechanical coupling behavior.     

A moving piezoelectric screw dislocation

A moving screw dislocation in a transversely isotropic piezoelectric material is investigated in detail. The analytical expressions for displacement, electric potential, stresses, electric displacements, strains, and electric fields are obtained. When the velocity of the dislocation is zero, or when the piezoelectric constant is zero, the results derived in this paper can reduce to known results.     

Analysis of a piezoelectric screw dislocation inside an elliptical inhomogeneity with confocal rigid line in piezoelectric material

This paper deals with the electro-elastic coupling interaction between a piezoelectric screw dislocation which is located inside the elliptical inhomogeneity and an electrically conductive confocal rigid line under remote anti-plane shear stresses and in-plane electrical loads in piezoelectric composite material. The analytical-functions of the complex potentials, stress fields and the image force acting on the piezoelectric screw dislocation are obtained based on the principle of conformal mapping, the method of series expansion, the technical of analytic continuation and the analysis of singularity of complex potentials. The rigid line and the piezoelectric material property combinations upon the image force and the equilibrium position of the dislocation are discussed in detail by the numerical computation.     

MOVING SCREW DISLOCATION IN CUBIC QUASICRYSTAL

The elasticity theory of the dislocation of cubic quasicrystals is developed. The governing equations of anti-plane elasticity dynamics problem of the quasicrystals were reduced to a solution of wave equations by introducing displacement functions, and the analytical expressions of displacements, stresses and energies induced by a moving screw dislocation in the cubic quasicrystalline and the velocity limit of the dislocation were obtained. These provide important information for studying the plastic deformation of the new solid material.     

SH波对一维六方准晶中直裂纹的散射

分析了SH波对一维六方准晶中直裂纹的散射问题。利用积分变换技术,结合Copson方法,通过求解对偶积分方程,得到声子场和相位子场应力、位移及裂纹尖端动应力强度因子的解析表达式。通过数值算例讨论了裂纹长度、入射角和入射波频率对标准动应力强度因子的影响,此研究在工程材料应用中有一定的参考价值。     

On the electroelastic interaction of a piezoelectric screw dislocation with an elliptical inclusion in piezoelectric materials

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｉｎｔｅｒａｃｔｉｏｎｏｆｄｉｓｌｏｃａｔｉｏｎｓｗｉｔｈｉｎｃｌｕｓｉｏｎｓｉｓｏｆｃｏｎｓｉｄｅｒａｂｌｅｉｍｐｏｒｔａｎｃｅｆｏｒｕｎｄｅｒｓｔａｎｄｉｎｇｔｈｅｐｈｙｓｉｃａｌｂｅｈａｖｉｏｒｏｆｍａｔｅｒｉａｌｓ.Ｓｕｃｈｓｔｕｄｉｅｓｃａｎｐｒｏｖｉｄｅｄｉｎｆｏｒｍａｔｉｏｎｃｏｎｃｅｒｎｉｎｇｃｅｒｔａｉｎｓｔｒｅｎｇｔｈｅｎｉｎｇｏｒｈａｒｄｅｎｉｎｇｍｅｃｈａｎｉｓｍｓｉｎｎｕｍｂｅｒｏｆｔｒａｄｉｔｉｏｎａｌａｎｄｃｏｍｐｏｓｉｔｅｍａｔｅｒｉ…     

ANALYSIS OF A SCREW DISLOCATION INSIDE A CIRCULAR INCLUSION WITH INTERFACIAL CRACKS IN PIEZOELECTRIC COMPOSITES

IntroductionPiezoelectric materials have potentials for use in many modern devices and compositestructures. The presence of various defects, such as inclusions, holes, dislocations andcracks, can greatly influence their characteristics and coupled behavio…     

Analytic solutions to problem of elliptic hole with two straight cracks in one-dimensional hexagonal quasicrystals

By means of the complex variable function method and the technique of conformal mapping, the anti-plane shear problem of an elliptic hole with two straight cracks in one-dimensional hexagonal quasicrystals is investigated. The solution of the stress intensity factor （SIF） for mode III problem has been found. Under the condition of limitation, both the known results and the SIF solution at the crack tip of a circular hole with two straight cracks and cross crack in one-dimensional hexagonal quasicrystals can be obtained.