Formation and dichroism of poly(vinyl alcohol)–iodine complex in photocurable film

The formation of polyiodine complexes was investigated in a photocurable poly(vinyl alcohol) modified N‐methyl‐4(4′‐formylstyryl)pyridinium methosulfate acetal (PVA‐SbQ), which is a photofunctional group that causes photodimerization. PVA‐SbQ films with polyiodine complexes were prepared to be photocured, iodinated and soaked in a boric acid solution. The formation of PVA–polyiodine complexes was studied during iodinating and while in the boric acid treatment through UV–vis absorption spectrometry, resonance Raman spectrometry and IR absorption spectrometry. As a result, polyiodines were formed in the photocurable PVA‐SbQ films, and the formation of PVA–polyiodine complexes was enhanced by boric acid treatment. It was found that the SbQ‐ratio of PVA‐SbQ affects the formation of PVA–polyiodine complexes. The photocrosslinking by the dimerization of SbQ groups helps to form the PVA–I₅⁻ complex during the boric acid treatment. Based on this effect, we demonstrated a unique recording method by the PVA–polyiodine complex formation. The PVA‐SbQ film cured by the irradiation of the liner polarized light showed that dichroism of the PVA–polyiodine complexes formed after iodination. Copyright © 2015 John Wiley & Sons, Ltd.     

Revisit to the photocrosslinking behavior of PVA‐SbQ as a water‐soluble photopolymer with anomalously low contents of quaterized stilbazol side chains

The photocrosslinking behavior of poly(vinyl alcohol) (PVA) substituted with 0.1, 0.3, 1.3, and 4.0 mol % of styrylpyridinium (SbQ) (PVA‐SbQs) side chains was reinvestigated. Even‐order derivative spectra of films of PVAs loaded with 0.1 and 0.3 mol % of SbQ revealed the presence of subpeaks owing to vibrational transitions, whereas PVA bearing 1.3 and 4.0 mol % of SbQ displayed a new blue‐shifted band (H‐band) at 328 nm due to H‐aggregation. Changes in derivative spectra disclosed the rapid disappearance of the H‐band of PVA‐SbQs under UV irradiation within exposure doses of 10 mJ cm^?2. On the other hand, the films of the PVA‐SbQs were insolubilized upon UV irradiation at exposure doses of 2 and 3 mJ cm^?2, respectively, leading to the conclusion that the high photosensitivity comes from the photodimerization of H‐aggregate as a ground‐state dimer. Fluorescence measurements implied the presence of J‐aggregate at 386 nm, but the involvement of the J‐aggregation in photocrosslinking was excluded because of its negligible fraction. A photosensitive emulsion of poly(vinyl acetate) emulsified with PVA‐SbQ exhibited similar changes in higher‐order derivative spectra in film and applied to fabricate a stencil for screen printing with aid of an LED‐emitting 375 nm light. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Photocatalytic Nanocomposite Films Fabricated by Layer‐by‐Layer Self‐assembly of TiO2 Nanoparticles and Lignosulfonates

Photocatalytic multilayer nanocomposite films composed of anatase TiO₂ nanoparticles and lignosulfonates (LS) were fabricated on quartz slides by the layer‐by‐layer (LBL) self‐assembly technique. X‐ray photoelectron spectroscopy (XPS), UV‐vis spectroscopy and atomic force microscopy (AFM) were used to characterize the TiO₂/LS multilayer nanocomposite films. Moreover, the photocatalytic properties (decomposition of methyl orange and bacteria) of multilayer nanocomposite films were investigated. XPS results indicated that the intensities of titanium and sulfur peaks increased with the LBL deposition process. A linear increase in absorbance at 280 nm was found by UV‐Vis spectroscopy, suggesting that stepwise multilayer growth occurs on the substrate and this deposition process is highly reproducible. AFM images showed that quartz slide was completely covered by TiO₂ nanoparticles when a 10‐bilayer multilayer film was formed. The decomposition efficiency of methyl orange by TiO₂/LS multilayer films under the same UV irradiation time increased linearly with the number of TiO₂ layers, and the results of decomposition of bacteria under UV irradiation showed that TiO₂/LS multilayer nanocomposite films exhibited excellent decomposition activity of bacteria (Escherichia coil).     

Dynamics of cyclodimerization and viscoelasticity of photo‐crosslinkable PVA

We investigated the interfacial properties of poly(vinyl alcohol) carrying UV‐crosslinkable pendant quaternized stilbazole (styrylpyridinium), PVA‐SbQ. The extent and dynamics of PVA‐SbQ cyclodimerization reactions and crosslinking induced by UV irradiation were monitored in situ and in real time by quartz crystal microgravimetry (QCM). Sensograms reflecting time‐dependent changes in density and viscoelasticity of crosslinking films followed a Boltzmann sigmoidal model, depending on precursor film composition and irradiation power. The shifts in QCM frequency and energy dissipation upon PVA‐SbQ cyclodimerization correlated with three photo‐crosslinking phases involving soft‐to‐rigid transitions, namely, induction (initiation), main crosslinking (interaction), and termination. PVA‐SbQ films crosslinked to different degree were used as protein carriers and a slower release profile was determined for the films that underwent more extensive crosslinking. Overall, this study demonstrates for the first time the dynamics of PVA‐SbQ crosslinking and its impact in system viscoelasticity and protein release. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 345–355     

Detection of layer‐by‐layer self‐assembly multilayer films by low‐temperature plasma mass spectrometry

The detection of layer‐by‐layer self‐assembly multilayer films was carried out using low‐temperature plasma (LTP) mass spectrometry (MS) under ambient conditions. These multilayer films have been prepared on quartz plates through the alternate assembling of oppositely charged 4‐aminothiophenol (4‐ATP) capped Au particles and thioglycolic acid (TGA) capped Ag particles. An LTP probe was used for direct desorption and ionization of chemical components on the films. Without the complicated sample preparation, the structure information of 4‐ATP and TGA on films was studied by LTP‐MS. Characteristic ions of 4‐ATP (M) and TGA (F), including [M]^+?, [M‐NH₂]⁺, [M‐HCN‐H]⁺, and [F + H]⁺, [F‐H]⁺, [F‐OH]⁺, [F‐COOH]⁺ were recorded by LTP‐MS on the films. However, [M‐CS‐H]⁺ and [F‐SH]⁺ could not be observed on the film, which were detected in the neat sample. In addition, the semi‐quantitative analysis of chemical components on monolayer film was carried out, and the amounts of 4‐ATP and TGA on monolayer surface were 45 ng/mm² and 54 ng/mm², respectively. This resulted the ionization efficiencies of 72% for 4‐ATP and 54% for TGA. In order to evaluate the reliability of present LTP‐MS, the correlations between this approach and some traditional methods, such as UV–vis spectroscopy, atomic force microscope and X‐ray photoelectron spectroscopy were studied, which resulted the correlation coefficients of higher than 0.9776. The results indicated that this technique can be used for analyzing the films without any pretreatment, which possesses great potential in the studies of self‐assembly multilayer films. Copyright © 2013 John Wiley & Sons, Ltd.     

Layer—by—layer Multilaryer Films Self—assembled from a Rare—earth—containing Poly—oxometalate,Na9[Eu（W5O18）2] and Poly （allylamine hydrochloride） and Their Photoluminescent Properties

Ultrathin multilayer films of a rare-earth-containing polyoxometalate Na9[Eu(W5O18)2](EW) and poly (allymamine hydrochloride)(PAH) have been prepared by layer-by-layer self-assembly from dilute aqueous solution.The fabrication process of the EW/PAH multilaryer films was followed by UV-vis spectroscopy and ellipsometry,which show that the deposition process is linear and highly reproducible from layer to layer.An average EW/PAH bilayer thickness of ca.2.1nm was determined by ellipsometry.In addition,the scanning electron microscopy(SEM) image of the EW/PAH film indicates that the film surface is relatively uniform and smooth.The photoluminescent properties of these films were also investigated by fluorescence spectroscopy.     

Electropolymerization of layer‐by‐layer precursor polymer films

The layer‐by‐layer (LbL) self‐assembly has been used to fabricate polymer thin films on any solid substrates. The multilayer polymer thin films are constructed by alternating adsorption of anionic and cationic polymers. Polyelectrolyte multilayer ultrathin films containing anionic poly[2‐(thiophen‐3‐yl)ethyl methacrylate‐co‐methacrylic acid]; P(TEM‐co‐MA) and cationic poly[4‐(9H‐carbazol‐9‐yl)‐N‐butyl‐4‐vinyl pyridium bromide]; P4VPCBZ, were fabricated. The growth of multilayer ultrathin films was followed by UV–Vis absorption spectrophotometer and surface plasmon resonance spectroscopy (SPR). The deposition of P(TEM‐co‐MA)/P4VPCBZ as multilayer self‐assembled ultrathin films regularly grow which showed linear growth of absorbance and thickness with increasing the number of layer pair. Cross‐linking of the layers was verified by cyclic voltammetry (CV), UV–Vis spectrophotometry and electrochemical surface plasmon resonance (EC‐SPR) spectroscopy with good electro‐copolymerizability. This was verified by spectroelectrochemistry. The SPR angular‐reflectivity measurement resulted in shifts to a higher reflectivity according to the change in the dielectric constant of the electropolymerized film. Copyright © 2011 John Wiley & Sons, Ltd.     

Preparation and characterization of covalently bonded PVA/Laponite/HAPI nanocomposite multilayer freestanding films by layer‐by‐layer assembly

The layer‐by‐layer (LBL) assembly technique is an attractive method to make functional multilayer thin films and has been applied to fabricate a wide range of materials. LBL materials could improve optical transmittance and mechanical properties if the film components were covalently bonded. Covalently bonded nanocomposite multilayer films were prepared by employing hydrophilic aliphatic polyisocyanate (HAPI) as the reactive component, to react with Laponite and polyvinyl alcohol (PVA). FT‐IR spectra suggested that HAPI reacted with Laponite and PVA at ambient temperature rapidly. Ellipsometry measurement showed that the film thickness was in linear growth. The influences of HAPI on the optical, mechanical and thermal properties of the films were investigated by UV‐Vis spectroscopy, tensile stress measurement, DSC and TGA. The obtained results showed that the optical transmittance and mechanical strength were enhanced when the film components were covalently bonded by HAPI. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 545–551     

Electrostatic Layer‐by‐Layer Assembly of Polycation and DNA Multilayer Films by Real‐time Surface Plasmon Resonance Technique

The assembly of alternating DNA and positively charged poly‐(dimethyldiallylammonium chloride) (PDDA) multilayer films by electrostatic layer‐by‐layer adsorption has been studied. Real time surface plasmon resonance (BIAcore) technique was used to characterize and monitor the formation of multilayer films in solution in real time continuously. The results indicate that the uniform multilayer can be obtained on the poly‐(ethylenimine) (PEI) coated substrate surface. The kinetics of the adsorption of DNA on PDDA surface was also studied by real‐time BIAcore technique, and the observed rate constant was calculated using a Langmuir model (k_obs = (1.28 ± 0.08) × 10^?2s^?1).     

Fabrication and Electrochemical Behavior of Vanadium‐Substituted Keggin‐Type Polyoxometalates Multilayer Films on 4‐Aminobenzoic Acid Modified Glassy Carbon Electrodes

Two Vanadium‐substituted Keggin‐type polyoxometalates, K₃H₂[α‐SiVW₁₁O₄₀]?6H₂O (SiVW₁₁) and K₄H₂[γ(1, 2)‐SiV₂W₁₀O₄₀]?4H₂O (SiV₂W₁₀) were first successfully immobilized on 4‐aminobenzoic acid modified glass carbon electrodes respectively by layer‐by‐layer assembly with poly (ethylenimine) (PEI) as counterions. The regular growth processes were monitored by cyclic voltammetry (CV), and it was proved that the multilayer films were uniform and stable. The cyclic voltammetry results indicated that the electrochemical behavior of two multilayer films was similar, and their redox couples are pH‐ and scan rate‐dependent. The multilayer films show favorable electrocatalytic active toward the reduction of NO₂^?, IO₃^? and H₂O₂.     

Layer‐by‐layer Assembled Multilayers of Graphene/Mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin for Detection of Dopamine

Graphene/mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin multilayer films composed of graphene sheet (GS) and mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin (NH₂‐β‐CD) were fabricated easily by two steps. First, negatively charged graphene oxide (GO) and positively charged mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin (NH₂‐β‐CD) were layer‐by‐layer (LBL) self‐assembled on glassy carbon electrode (GCE) modified with a layer of poly(diallyldimethylammonium chloride) (PDDA). Then graphene/mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin (GS/NH₂‐β‐CD) multilayer films were built up by electrochemical reduction of graphene oxide/mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin (GO/NH₂‐β‐CD). Combining the high surface area of GS and the active recognition sites on β‐cyclodextrin (β‐CD), the GS/NH₂‐β‐CD multilayer films show excellent electrochemical sensing performance for the detection of DA with an extraordinary broad linear range from 2.53 to 980.05 µmol·L^?1. This study offers a simple route to the controllable formation of graphene‐based electrochemical sensor for the detection of DA.     

Multilayer Assemblies Consisting of Tri‐Vanadium‐Substituted Heteropolyanions and Its Electrocatalytic Properties

We describe the controlled fabrication of ultrathin multilayer films consisting of tri‐vanadium‐ substituted heteropolytungstate anions (denoted as P₂W₁₅V₃) and a cationic polymer of quaternized poly (4‐vinylpyridine) partially complexed with osmium bis(2,2′‐bipyridine) (denoted as QPVP‐Os) on the 4‐aminobenzoic acid (4‐ABA) modified glassy carbon electrode (GCE) surface based on layer‐by‐layer assembly. Cyclic voltammetry and UV‐vis absorption spectrometry have been used to easily monitor the thickness and uniformity of thus‐formed multilayer films. The V‐centered redox reaction of P₂W₁₅V₃ in the multilayer films can effectively catalyze the reduction of BrO and NO . The resulting P₂W₁₅V₃/QPVP‐Os multilayer film modified electrode behaves as a much promising electrochemical sensor because of the low overpotential for the catalytic reduction of BrO and NO , and the catalytic oxidation of ascorbic acid.     

Layer‐by‐layer ionomer films made from poly(styrene‐co‐styrenesulfonic acid) and poly(methyl methacrylate‐co‐4‐vinylpyridine) in tetrahydrofuran

Thin films were fabricated layer‐by‐layer (LbL) via ionic bonds formed between a cationic ionomer and an anionic ionomer, which were produced via proton transfer from poly(styrene‐co‐styrenesulfonic acid) to poly(methyl methacrylate‐co‐4‐vinylpyridine) in an organic solvent, tetrahydrofuran. Ionic contents of the ionomers were very low down to 5.6 mol %, much lower than usual polyelectrolytes. The build up of the LbL films was demonstrated by UV/vis spectroscopy: the absorbance of the phenyl rings in styrene residues increased with the number of depositions (thus the number of layers). Transmission electron microscopy observation of strained thin films showed unique deformation mode, involving many bands that developed both in the parallel and perpendicular directions to the stress axis. This is quite different from the deformation modes seen for ionomer blend films and for coextruded polystyrene/poly(methyl methacrylate) multilayer tapes. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 50: 101–105, 2012     

Synthesis of pH‐responsive photocrosslinked hyaluronic acid‐based hydrogels for drug delivery

Photocrosslinked hyaluronic acid/poly(vinyl alcohol)‐styrylpyridinium (HA/PVA‐SbQ) hydrogels were synthesized for controlled antitumor drug delivery. The photocrosslinking reaction was rapid, and the time required for completely converting into the insoluble hydrogels was less than 500 s on exposure to 5 mW/cm² UV light irradiation. The resulting hydrogels exhibited sensitivity to the pH value of the surrounding environment. Scanning electron microscopic analysis revealed that the morphology and the pore size of the hydrogels could be controlled by changing the ratio of HA and PVA‐SbQ in the formulations. Paclitaxel (PTX)‐loaded hydrogel could also be formed rapidly by UV irradiation of a mixed solution of HA/PVA‐SbQ and PTX. Release profiles of PTX from the hydrogels showed pH‐dependent and sustained manner. Moreover, our data revealed that PTX released from the HA hydrogels remained biologically active and had the capability to kill cancer cells. In contrast, control groups of HA hydrogels without PTX did not exhibit any cytotoxicity. This study demonstrates the feasibility of using HA‐based hydrogels as a potential carrier for chemotherapeutic drugs for cancer treatments. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Sensitively Electrochemical Sensing for Sequence‐Specific Detection of Phosphinothricin Acetyltransferase Gene: Layer‐by‐Layer Films of Poly‐L‐Lysine and Au‐Carbon Nanotube Hybrid

An electrochemical DNA sensing film was constructed based on the multilayers comprising of poly‐L ‐lysine (pLys) and Au‐carbon nanotube (Au‐CNT) hybrid. A precursor film of mercaptopropionic acid (MPA) was firstly self‐assembled on the Au electrode surface. pLys and Au‐CNT hybrid layer‐by‐layer assembly films were fabricated by alternately immersing the MPA‐modified electrode into the pLys solution and Au‐CNT hybrid solution. Cyclic voltammetry was used to monitor the consecutive growth of the multilayer films by utilizing [Fe(CN)₆]^3?/4? and [Co(phen)₃]^3+/2+ as the redox indicators. The outer layer of the multilayer film was the positively charged pLys, on which the DNA probe was easily linked due to the strong electrostatic affinity. The hybridization detection of DNA was accomplished by using methylene blue (MB) as the indicator, which possesses different affinities to dsDNA and ssDNA. Differential pulse voltammetry was employed to record the signal response of MB and determine the amount of the target DNA sequence. The established biosensor has high sensitivity, a relatively wide linear range from 1.0×10^?10 mol/L to 1.0×10^?6 mol/L and the ability to discriminate the fully complementary target DNA from single or double base‐mismatched DNA. The sequence‐specific DNA related to phosphinothricin acetyltransferase gene from the transgenically modified plants was successfully detected.     

Mechanical property and corrosion resistance of zirconia/polydopamine nanocomposite multilayer films fabricated via a novel non‐electrostatic layer‐by‐layer assembly technique

Zirconia/polydopamine (ZrO₂/PDA) nanocomposite multilayer films were constructed on Si substrate via a novel nonelectrostatic layer‐by‐layer (NELBL) assembly technique. The building block of this technique is the newly reported dopamine molecule, which can be attached to almost all material surfaces and undergo oxidation‐polymerization to form PDA layers; more importantly, the outer hydroxyl groups of the PDA layer can chelated with certain inorganic oxide nanoparticles to generate oxide films. Thus, ZrO₂/PDA nanocomposite multilayer films were fabricated by sequential NELBL deposition of PDA and ZrO₂ nanoparticles. The formation of the ZrO₂/PDA nanocomposite multilayer films was monitored by the water contact angle (WCA) and ellipsometric thickness measurements, while the microstructure of the fabricated films was analyzed by means of atomic force microscope (AFM), field emission scanning electron microscope (FESEM), X‐ray photoelectron spectrum (XPS), and X‐ray diffraction (XRD) analysis. The mechanical and anticorrosion behaviors of the annealed ZrO₂/PDA nanocomposite multilayers were found to be greatly enhanced as compared with that of the annealed homogeneous ZrO₂ film. The better mechanical and anticorrosion behaviors of the annealed ZrO₂/PDA nanocomposite multilayers than the annealed homogeneous ZrO₂ film may be closely related to their special microstructure. Namely, the organic–inorganic hybrid microstructure of the annealed ZrO₂/PDA nanocomposite multilayers may largely account for the increased nanohardness and corrosion resistance. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation and resistivity study of silver nanocomposite films using spin‐assisted layer‐by‐layer assembly

Nanocomposite films [Ag/(PAH‐PSS)_nPAH]_m were fabricated on a silicon substrate using a time‐ and cost‐efficient spin‐assisted layer‐by‐layer (SA‐LbL) self‐assembly technique. A virtually monolayer‐like layer of self‐assembled silver nanoparticles was formed when deposition time increased to 30 min. It was found that polymer multilayers could effectively decrease the resistivity of silver nanoparticle monolayer, which was far higher than that of bulk silver metal; however, the resistivity of Ag/(PAH‐PSS)_nPAH multilayer films increased along with the increasing of the number of polymer bilayers. XPS investigations showed that silver nanoparticles were partially oxidized, which might be the major cause of the high resistivity of silver nanoparticle monolayer. Copyright © 2008 John Wiley & Sons, Ltd.     

Electrochemical Investigation of Myoglobin in Layer‐by‐Layer Films Assembled with Sulfonated‐β‐Cyclodextrin

In this work, myoglobin (Mb) and sulfonated‐β‐cyclodextrin (S‐CD) were assembled into {S‐CD/Mb}_n layer‐by‐layer films on solid substrates. In pH 7.0 buffers, the {S‐CD/Mb}_n films assembled on electrodes showed a pair of well‐defined and nearly reversible CV peaks at about ?0.35 V vs. SCE. The stable CV response of {S‐CD/Mb}_n films could be used to electrocatalyze reduction of oxygen and hydrogen peroxide in solution. For comparison, another modified β‐cyclodextrin, carboxyethyl‐β‐cyclodextrin (C‐CD), was also assembled with Mb into {C‐CD/Mb}_n multilayer films. The driving forces of the assembly were explored and discussed.     

Influence of graphene oxide incorporation and chemical cross‐linking on structure and mechanical properties of layer‐by‐layer assembled poly(Vinyl alcohol)‐Laponite free‐standing films

Functional fillers in multilayered films provide opportunity in tailoring the mechanical properties through chemical cross‐linking. In this study, Laponite‐graphene oxide co‐dispersion was used to incorporate graphene oxide (GO) easily into polyvinyl alcohol (PVA)/Laponite layer‐by‐layer (LBL) films. The LBL films were found to be uniform and the layer thickness increased linearly with number of depositions. The process was extended to a large number of depositions to investigate the macroscopic mechanical properties of the free‐standing films. The LBL films showed remarkable improvements in mechanical properties as compared to neat PVA film. The GO‐incorporated LBL films displayed higher enhancements in the tensile strength, ductility, and toughness as compared to that of PVA/Laponite LBL films, upon chemical cross‐linking. This suggests the advantageous effects of GO incorporation. Interestingly, cross‐linking of LBL films for longer time period (>1 h) and higher temperature (～80 °C) was not found to be much beneficial. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2377–2387     

Crosslinkable poly(p‐phenylenevinylene) derivative

To simplify the fabrication of multilayer light‐emitting diodes, we prepared a p‐phenylenevinylene‐based polymer capped with crosslinkable styrene through a Wittig reaction. Insoluble poly(p‐phenylenevinylene) derivative (PPVD) films were prepared by a thermal treatment. The photoluminescence and ultraviolet–visible (UV–vis) absorbance of crosslinked films and noncrosslinked films were studied. We also studied the solvent resistance of crosslinked PPV films with UV–vis absorption spectra and atomic force microscopy. Double‐layer devices using crosslinked PPVD as an emitting layer, 2‐(4‐tert‐butylphenyl)‐5‐phenyl‐1,3,4‐oxadiazole (PBD) in poly(methyl methacrylate) as an electron‐transporting layer, and calcium as a cathode were fabricated. A maximum luminance efficiency of 0.70 cd/A and a maximum brightness of 740 cd/m² at 16 V were demonstrated. A 12‐fold improvement in the luminance efficiency with respect to that of single‐layer devices was realized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2124–2129, 2004