高残炭硼酚醛树脂的制备

酚醛树脂(PF)因其具有良好的耐热性能和机械性能而被广泛应用。但其耐热性能已经满足不了现代航空航天技术的需求,研究发现,采用硼酸对酚醛树脂进行改性,可以制得具有优良耐高温性能的硼酚醛树脂(BPF)。采用硼酸酯法合成硼酚醛树脂,n(苯酚)∶n(甲醛)=1∶1.5时耐热性最佳。热分析结果表明,合成的BPF在1000℃条件下的残炭率为78%,其耐热性能明显优于传统的酚醛树脂。同时讨论了不同硼酸含量对BPF耐热性能的影响,当n(硼酸)∶n(苯酚)0.33∶1时,残炭率趋于稳定。此外,利用差示扫描量热仪(DSC)方法确定BPF预固化温度为160℃,后固化温度为220℃。     

油溶性硼改性酚醛树脂的合成

普通酚醛树脂(ＰＦ)对热稳定性较差(初始热分解温度一般≤200℃),脆性大和吸水率高,用于摩阻材料特别是各种高速机械运转刹车带方面受到一定的限制[1-4]。由于生产工艺的要求,部分制动带生产厂家要求改性酚醛树脂能熔融于特定的油料中。为此,我们采用硼酸对酚醛树脂进行化学改性,使之溶于桐油中。1　实验部分1 1　油溶性改性酚醛树脂的合成在装有电动搅拌器,分水回流冷凝管及温度计的三口烧瓶中,按一定的物质量比投入融化的苯酚,硼酸,醇类和催化剂等,在高速搅拌下加热至设定温度Ⅰ,保持反应5—8ｈ,再将体系温度升至设定温度Ⅱ,脱出馏出…     

高邻位高分子量热塑性酚醛树脂研制

改变传统合成工艺,在高温高压无催化剂条件下,合成了无金属杂质的高邻位高分子量热塑性酚醛树脂。考察了苯酚与甲醛加成缩合反应过程中原料种类、原料配比、反应温度及反应压力等因素对酚醛树脂结构性能的影响。通过软化点测试仪、核磁共振谱仪等研究了酚醛树脂合成过程中各个参数对酚醛树脂结构性能的影响。在酚／醛比为1：0．7,210℃、...     

硼酸与甲阶酚醛树脂的配位反应及配合物的结构

本文通过对溶液pH值的测定和外光谱分析，研究了硼酸与甲阶酚醛树脂的配位反应。结果表明：在室温下硼酸能与甲阶酚醛树脂中的羟基发生配位反应，并产生H^ 使溶液的pH值降低；溶液的酸性强弱与甲阶酚醛树脂中的羟甲基含量和硼酸的用量有关；硼酸以硼酸根离子的形式与树脂中的酚羟基和邻位羟甲基发生配位反应，形成了一个含有两个氧原子和一个硼原子的六元环，使甲阶酚醛树脂发生交联。     

有机硅改性硼酚醛树脂的研制

通过Williamson醚合成、Claisen重排及硅氢化反应得到邻羟基苯丙基硅油(Si-phenol),将其与苯酚混合,采用硼酸酯法合成有机硅改性硼酚醛树脂(SBPF).利用1H NMR和FTIR技术对其结构进行分析,采用热重分析(TGA)、剪切测试、拉伸测试以及冲击测试等手段对其耐热能和力学性能进行表征.考察了Si-phenol的含量对树脂各项性能的影响,并研究其作用机理.结果表明,合成的有机硅改性硼酚醛树脂具有良好的耐热性,适量硅氧烷链段的引入可以改善树脂的黏接性能,提高其力学强度.     

新型硼氮磷一体化阻燃剂的合成

分别以硼酸、二乙醇胺、三氯氧磷和季戊四醇为原料,经酯化反应制得中间体二乙醇胺硼酸酯（DEAB, 1）和双季戊四醇二氯磷酸酯（SPDPC, 2）; 1与2经缩聚反应合成新型集磷、氮、硼于一体的阻燃剂聚季戊四醇双磷酸酯二磷酰氯螺环二乙醇胺硼酸酯（PPSPSDB, 3）,其结构经¹H NMR, ¹³C NMR和FT-IR表征。考察了溶剂、物料比γ［n(2)：n(1)］、反应温度和反应时间对3产率的影响,结果表明：在最佳反应条件（DMF为溶剂,γ=1 ：1.2, 于120 ℃反应2 h后,于190 ℃反应2 h）下,产率93.26%。热重分析表明：3的初始分解温度为240.5 ℃, 800 ℃时残炭率为44.45%。     

吡咯烷酮酸性离子液体中硼酸酯的催化合成

研究了硼酸与频哪醇和环己醇在离子液体1-甲基-2-吡咯烷酮硫酸氢盐（[Hnmp]HSO4）、1-丁基-3-甲基咪唑四氟硼酸盐（[Bmim]BF4）及1-丁基-3-甲基咪唑六氟磷酸盐([Bmim]PF6)中生成2-环己氧基-4,4,5,5-四甲基-1,3,2-二氧硼烷的酯化反应。 考察了不同离子液体、反应温度、反应时间和离子液体与反应物物质的量比等对反应的影响。 结果表明,当n(硼酸)∶n(频哪醇)∶n(环己醇)∶n([Hnmp]HSO4)=1∶1∶1∶1,反应温度为70 ℃和反应时间为4 h时,硼酸酯的产率为72.5%,离子液体重复使用4次,催化活性无明显降低。     

气相色谱法测定酚醛树脂中游离苯酚

建立气相色谱外标标准曲线法测定酚醛树脂中游离苯酚的含量。采用DB–5(30 m×0.25 mm, 0.25μm)色谱柱,程序升温,气化室温度为250℃,以火焰离子化检测器(FID)检测,检测器温度为280℃,以标准曲线外标法计算游离苯酚含量。苯酚的质量浓度在0.05～10.0 mg/mL范围内与色谱峰面积呈良好的线性关系,线性相关系数(r)为1,方法检出限为0.003 7 mg/mL。样品加标回收率为98.0%～102.0%,测定结果的相对标准偏差为1.07%～1.26%(n=6)。该方法简单、快速,测定结果准确、可靠,可用于酚醛树脂中游离苯酚含量的检测。     

氯铝酸室温离子液体中双酚A的合成

以Et3NHCl-AlCl3离子液体为催化剂,通过苯酚和丙酮缩合反应合成双酚A。考察了离子液体的催化活性,较系统地研究了催化剂路易斯酸性、催化剂用量、反应物摩尔比、反应温度、反应时间对产率的影响。最佳反应条件为：丙酮10mmol,n(酚)：n(酮)=8：1,催化剂Et3NHCl-AICl3[n(AICl3)：n(Et3NHCl-AICl3)=0．6]10．7mmol,硫醇(助剂)0．2mmol,反应温度60℃,在25mL的甲苯中反应4h。此条件下收率可达85．1％。     

硼化锆陶瓷前驱体法制备及其表征

以聚乙酰丙酮锆(PZO)、硼酸、酚醛树脂为原料制备得到硼化锆液相前驱体;在1 400℃和氩气保护下使硼化锆前驱体发生碳热还原反应,得到硼化锆陶瓷.采用热重分析仪、X射线衍射仪、电感耦合等离子体发射光谱仪、扫描电镜表征了硼化锆前驱体及热解陶瓷产物.结果表明,在相对较低的温度(1 400℃)下热解得到的硼化锆陶瓷纯度较高;硼化锆陶瓷材料整体呈小块状,由硼化锆晶体层层堆积而成,其晶粒尺寸约为200 nm.     

8—羟基喹啉树脂的制备及应用研究进展

本文总结了国内外关于8－羟基喹啉螯合树脂的制备方法,树脂性能及其应用。     

Recent development on bio-based thermosetting resins

Due to the rapid depletion of crude oil and serious environmental pollution, the synthesis of polymers from renewable resource is becoming more and more important. Up to now, a great variety of biomass and bio-based platform compounds have been taken to prepare the polymers. However, as two representative thermosetting resins, epoxy and benzoxazine resin derived from renewable feedstocks only obtain limited attention compared with the popular bio-based plastics, including PLA, PBAT and PHBV etc. The reason might be that the properties of previously reported thermosetting resins directly obtained from biomass are usually unsatisfied, and their application fields are limited. In this paper, the latest development on the synthesis of high-performance bio-based epoxy and polybenzoxazine resins are reviewed. In addition, to further broaden their applications, the functionalization strategies are also summarized. The objective of this work is to help us fully aware the present situation of bio-based thermosetting resins and then promote their faster development, especially practical application.     

Polyacrolein-isonicotinic acid hydrazone and polyacrylic acid-thiohydrazide resins-synthesis and sorption properties for precious and base metals

This investigation carries on previous studies on polyacrolein-styrene resins. Further attempts were made to convert the reactive aldehyde groups of the polymeric support to functional acrolein-isonicotinic acid hydrazone (P-NHZ) or acrylic acid-thiohydrazide derivatives (P-THZD). The conditions of synthesis and the basic sorption and desorption properties of the polymers synthesized are described. For gold and platinum group metals the resins show differences in loading capacities, rates of simultaneous sorption in static conditions and efficiencies in column tests. The elution by thiourea solution was utilized to separate Au, Pd and Pt from an excess of base metals. The P-NHZ resin seems to be more advantageous than the sulfur containing P-THZD resin.     

磺化三聚氰胺甲醛树脂与金属钙离子的复合物对水泥的作用

研究了磺化三聚氰胺甲醛树脂（SMF）与金属钙离子的复合物SMF-Ca^2 对水泥的作用,从对水泥吸附、水化等研究结果表明,SMF和Ca^2 间存在着一定的化学作用。在水泥砂浆中加入SMF-Ca^2 复合物比加入纯的SMF树脂能使减水率、抗压强度、抗折强度获得更大的提高。     

苯氧树脂增韧双酚A环氧树脂的研究

以双官能团环氧树脂和双酚Ａ为单体，制备高分子量苯氧树脂，通过ＦＴＩＲ对其分子结构进行分析后，将１０ｗｔ％苯氧树脂加入到Ｅ－４４环氧树脂中，用ＤＳＣ冲击仪和ＳＥＭ等对增韧效果的分析测定，固化反应活化能降低９％，冲击强度提高６３．２％，玻璃化温度提高了２８℃。     

硅炔杂化树脂改性有机硅树脂及其复合材料的性能

用一种硅炔杂化树脂聚（甲基硅烷-二乙炔基苯）（PSP）改性有机硅树脂（HS）,通过FT—IR和TGA研究了树脂体系的固化反应及耐热性,并对制备的复合材料进行力学性能、耐热性能和介电性能研究。结果表明：当HS与PSP的质量比为5：5时综合性能最优,树脂体系在氮气氛围下质量损失5％时的温度（T幽）为691℃,1000℃时质量保留率为88％;HS—PSP树脂短切玻纤复合材料冲击强度为21kJ／m^2,弯曲强度为65MPa,200℃时的弯曲强度高温保留率为78％,介电常数为4．6,介电损耗因数为7．9×10,体积电阻为6．7×10^13Ω。改性后的复合材料具有优异的力学、耐热和介电性能。     

Studies on the synthesis and curing of epoxidized novolac vinyl ester resin from renewable resource material

Cardanol-based epoxidized novolac vinyl ester resin (CNEVER) was synthesized by reacting cardanol-based epoxidized novolac (CNE) resin and methacrylic acid (MA) (CNE:MA molar ratio 1:0.9) in presence of triphenylphosphine as catalyst at 90 °C. The CNE resin was prepared by the reaction of cardanol-based novolac-type phenolic (CFN) resin and epichlorohydrin, in basic medium, at 120 °C. The CFN resin was synthesized by reacting cardanol (C) and formaldehyde (F) (C/F ratio = 1:0.7) with p-toluene sulphonic acid (PTSA) as catalyst (0.5 wt.%) at 120 °C for 7 h. The resin products were analyzed by Fourier-transform infra-red (FTIR) and nuclear magnetic resonance (NMR) spectroscopic analysis. The number-average molecular weight of the prepared CNEVER was found to be 859 gmol⁻¹ as determined by gel permeation chromatographic (GPC) analysis. The resin was cured by using the mixture of resin, benzoyl peroxide, and styrene at 120 °C. The CNEVER resin was found to be cured in 60 min at 120 °C. Differential scanning calorimetric (DSC) technique was used to investigate the curing behaviour. Single step mass loss in dynamic thermogravimetric (TG) trace of CNEVER was observed. Thermal stability of the vinyl ester sample containing 40 wt.% styrene was the highest amongst all other prepared systems.     

硼酸盐固化酚醛树脂

硼酸与多元醇的络合反应已被用于硼酸浓度的滴定分析、硼选择性树脂等[1 ] 。Ecolotec树脂是一种用硼酸盐固化的碱性酚醛树脂 ,制备时以KOH溶液为溶剂 ,以硼砂为交联剂 ,通入CO2 降低溶液 pH值而交联 ,因其固化快、无污染 ,可用作铸造用冷芯盒树脂砂粘结剂。加入硅烷偶联剂与增塑剂能大幅度提高树脂砂固化后的抗拉强度[2 ] ,以碱金属氧化物与氢氧化物作为促硬剂 ,也可以提高树脂砂强度[3] 。赵鹏等[4] 合成了G盐改性酚醛树脂 ,由该树脂得到的树脂砂固化后 2 4h强度高于Ecolotec树脂。谭晓明等[5 ,6] 发现 ,树脂与硼酸根离子的配位反应是…     

蛇笼树脂

蛇笼树脂作为一种有特异性能的离子交换树脂,发展较快。本文就该树脂的定义、特点、类型、合成方法及应用实例等的近期发展进行了较详细的分析和综述。     

Modification of epoxy-novolac resins with polysiloxane containing nitrile functional groups: synthesis and characterization

Synthesis of the statistical epoxidized polycyanopropylmethylsiloxane-co-polydimethylsiloxanes (PCPMS-co-PDMS) has been demonstrated. The modified polysiloxanes were prepared via a two-step method; (1) the ring-opening polymerization of octamethylcyclotetrasiloxane (D₄) and tetramethylcyclotetrasiloxane (D₄H), (2) hydrosilylation reaction of the polysiloxane prepolymers with allyl cyanide and allyl glycidyl ether. Molar ratios of D₄H and D₄ were varied to produce the modified polysiloxanes with differences in polarity. ¹H-NMR, ²⁹Si-NMR, ¹³C-NMR and FTIR were used to monitor the formation of the modified polysiloxanes and DSC was used to study their thermal behaviors (T_g, −118 to −68 °C). The use of the modified polysiloxanes as an elastomeric component in epoxy-novolac networks was also investigated. TEM and their transition temperatures suggested that the epoxy-novolac networks with high content of PDMS modifiers exhibited microphase separation. The fracture toughness properties of the networks with the polysiloxane modifiers were improved over the controls without polysiloxanes.