Quantitative visualization of the leading-edge vortices on a delta wing by using pressure-sensitive paint

Leading-edge vortices on a simple delta wing were visualized by using pressure-sensitive paint (PSP). PSP is an optical pressure measurement technique based on oxygen quenching of luminescent molecules. In the present study, we used PSP composed of platinum octaethylporphyrine (PtOEP) and fluoropolymer (poly-IBM-co-TFEM [Poly (isobutylmethacrtlate-co-trifluoroethylate)]). This new paint has higher sensitivity to pressure and lower sensitivity to temperature than previous ones, reducing an error due to temperature variation during a wind tunnel test. A thin coating of PSP was applied to a delta wing model with 70-degree leading-edge sweep. The coating was excited by Xenon light and emission from the coating was detected by a high-resolution CCD camera. Tests were done at subsonic speeds in the 0.2-m Supersonic Wind Tunnel at the National Aerospace Laboratory in Japan. Complicated flow structures on the delta wing including primary and secondary vortices were clearly visualized using pressure-sensitive paint. An a priori calibration technique was used to convert measured luminescent intensity into pressure. The obtained pressure distributions were in good agreement with pressure tap data. Pressure maps were obtained for various Mach numbers, Reynolds numbers and angles of attack. It was found that an increase in Mach number delayed vortex breakdown while Reynolds number had little effect on the vortex formation.     

Unsteady surface signature of a pulsed vortex generator jet

Abstract  

Porous pressure-sensitive paint (PSP) is employed as a visualization technique for unsteady flow features on a low-pressure turbine blade. Recognizing that the measurement of high-frequency pressure fluctuations in unsteady flows—especially in turbomachinery—has proven to be difficult, recent advancements in the development of porous PSP have enabled the high-resolution measurement of pressure fields with frequency content of at least 20 kHz. In this work, PSP is applied to an L1A low-pressure turbine blade section (Re = 20,000 based on axial chord) to visualize the surface dynamics of a vortex generator jet (VGJ) pulsed at 10.6 Hz with nitrogen gas. Intensity-based, time-resolved PSP measurements reveal the development and the surface structure of the VGJ as well as the spanwise variation in the blowing profile.     

PSP技术在叶栅叶片表面压力测量中的应用

PSP(Pressure Sensitive Paint)测量技术以不改变叶片表面结构及可以进行全域压力测量的独特优势而受到广泛关注,但是受到几何结构的限制,有关内流场的PSP测量实验难度非常大.本文对ISSI公司所生产PSP测量系统开展了校准试验,完成了三个来流马赫数下叶栅叶片吸力面上静压分布的测量,并与传统压力扫描...     

Pressure-Sensitive Paint measurement of the flow around a simplified car model

In applying Pressure-Sensitive Paint (PSP) to low-speed flow wind tunnel testing, it is important to minimize any measurement uncertainties. There are various error sources such as camera noise, misalignment of images due to model displacement and temperature distribution over the model. Among these factors, the effects of temperature distribution change during tests on pressure measurement accuracies were studied in the present paper. Pressure and temperature distributions over a simplified car model (1/10 scale Ahmed model) were measured using PSP and Temperature-Sensitive Paint (TSP). Sequential images were acquired at the same intervals over the entire test period, including for the conditions before and after the tunnel run. As a result, it was found that the measurement error caused by temperature distribution over the model could be reduced using a single-point temperature measurement. In addition, by measuring surface temperature distributions on the model using TSP, it was proved that the most accurate pressure measurement could be made by rationing the wind-off image acquired immediately after shutting down the tunnel to the wind-on image acquired immediately before shutting down the tunnel. Using the present measurement technique, complicated pressure fields over the Ahmed model were successfully visualized.     

Application of pressure sensitive paint measurement to a low-solidity cascade diffuser of a transonic centrifugal compressor

A pressure sensitive paint (PSP) measurement has been known as a pressure field measurement technique based on the oxygen quenching phenomenon of luminescence of specific luminophores. A PSP measurement was applied for pressure field measurement in a low-solidity circular cascade diffuser of a single-stage transonic centrifugal compressor with 5 in pressure ratio for HFC134a gas. The oxygen concentration was about 500 ppm. Ru (bath-phen) was adsorbed on a silica-gel thinlayer chromatography sheet, and the sheet was pasted onto the side-wall between the cascade vanes. A drastic change in luminescent intensity was recognized during a surge condition. Also the pressure variations based on luminescent intensity agreed well with the pressure fluctuations measured using a semiconductor pressure sensor with high-frequency-response. It was shown that a PSP measurement worked well to investigate the unsteady pressure fields in a circular cascade diffuser of a transonic centrifugal compressor. Moreover, the time response of PSP becomes clear as a problem to be overcome for the present.     

Development of a pressure sensitive paint technique for low-speed flows and its application

Pressure sensitive paint (PSP) techniques have been used to measure the pressure distribution on a model surface in high-speed flows. In this study, we developed a PSP technique that can be applied to low-speed flows. Four PSP formulations, each comprised of a porphyrin (PtOEP or PtTFPP) and a polymer (Poly(TMSP) or RTV-118), were tested and the performance of each combination was evaluated. In the static calibration, the luminescence intensity of the PSP coatings was measured from 0 kPa to 11 kPa with 0.5, 1, and 2 kPa increments. Among the four PSP formulations tested, the combination of PtOEP and RTV-118 (PSP-3) showed the best performance. In this study, the low-pressure PSP technique using PSP-3 was applied to an oblique impinging subsonic jet to measure pressure field distributions on the impingement plate at various angles of the oblique jet. For comparison, the flow over the impingement plate was visualized using an oil-film method.     

开式轴流风扇气动噪声预测

本文采用LES/FW-H的匹配方法,研究了开式轴流风扇内部旋涡流动特征及其与叶片表面干涉引起的气动噪声之间的联系,同时进行了远场噪声预测,探讨了叶轮不同表面辐射噪声时的频谱分布特征.研究结果表明,开式轴流风扇吸力面附近形成的叶尖涡和前缘分离涡在吸力面叶片表面相应位置形成大压力波动,形成主要噪声源;叶片吸力面的辐射噪声可以通过改善吸力面附近的旋涡流动来降低;低速轴流叶轮由叶轮壁面辐射的噪声以宽频成分为主.     

Flow field measurements of leading-edge separation vortex formed on a delta wing with vortex flaps

Wind tunnel tests are carried out using a 70 delta wing model with leading-edge vortex flaps. The structure of the leading-edge separation vortex over the leading-edge vortex flap is measured by use of a 5 holes pitot probe, surface pressure measurement technique and oil flow visualization technique. Separation vortices formed on a plain delta wing, on a vortex flap and inboard the vortex flap hinge line are clearly visualized. Results indicate that the flow around the vortex flaps is classified into several different cross flow patterns. The streamwise flap deflection angle is defined to discuss the vortex flap performance. The optimum lift to drag ratio is attained when the amount of the wing angle of attack is not far different from that of the streamwise flap deflection angle, as long as the vortex flap is deflected modestly.     

Quantitative wind tunnel studies using pressure- and temperature sensitive paints

The pressure sensitive paint (PSP) intensity and lifetime system is an optical measurement technique to investigate absolute pressure fields on model surfaces for basic research in laboratories, industrial wind tunnels or high speed rotating turbo machines. Detailed qualitative and quantitative information and understanding of flow phenomena can be obtained in speed ranges from U_∞=20 m/s up to Ma=5.0. A number of projects of industrial interest has been investigated in different wind tunnels covering low speed, transonic, trisonic and cryogenic facilities. The influence of the main error sources for the components of the PSP system have been checked. Comparison of experimental pressure fields obtained by means of PSP and the results of numerical calculations have been carried out. Different wind tunnel models ranging from basic configurations such as a cropped delta wing to a complex half model of a large propeller-driven transport aircraft with all flaps, rudders and shrouds, and rotating or oscillating models as well as Reynolds number effects on models have been investigated.     

轴流风扇叶片端导叶作用的研究

本文采用数值方法研究了叶片端导叶对轴流风扇性能的影响。通过与普通开式轴流风扇比较,分析了叶片端导叶对内部流动作用的机理.数值计算结果表明:叶片端导叶的安装位置将影响轴流风扇气动效率,安装叶片端导叶不能提高风扇静压升,但是在压力面安装时能有效地减小风扇叶顶泄漏流与主流的掺混损失;在设计流量下,压力面安装叶片端导叶使泄漏涡的作用范围较小,涡核更靠近吸力面;吸力面安装叶片端导叶弱化了泄漏涡的强度但没有减小泄漏涡的作用范围。     

高雷诺数双螺旋涡尾迹演化特性分析

螺旋状尾迹涡是直升机悬停旋翼流场的主导特征之一,其时空演化特性对旋翼气动性能具有重要影响.为了揭示悬停状态下旋翼尾迹涡的演化特征,对两桨叶刚性旋翼在高雷诺数悬停状态下的双螺旋状尾迹涡开展数值研究,采用基于流场特征的网格自适应技术,结合低耗散迎风/中心混合格式以及延迟脱体涡模拟方法对Caradonna-Tung旋翼在桨尖马赫数为0.439、桨尖雷诺数为1.92×10~6的悬停流场进行了高分辨率计算.基于欧拉和拉格朗日两种描述方法对计算结果进行了分析,揭示了双螺旋尾涡系统的演化特性:后缘尾涡面在桨尖附近的反向卷起及其与下游桨尖涡的相互作用是影响涡系稳定性以及涡-涡相互作用的重要因素;涡龄小于720°时,在固连于桨叶上的旋转坐标系中观察,涡系具有时空稳定性,涡管中心处轴向涡量随涡龄按照幂函数规律衰减.在固连于漩涡中心的局部极坐标系中,周向速度分布以及涡核半径随涡龄的变化与理论涡模型相符合,环量随涡龄的变化显示了漩涡的生长、平衡及耗散等演化阶段;模态分析结果表明,除点涡模态外,来流与点涡的复合模态在漩涡演化过程中对流动特征的转变有重要影响;涡系轴截面速度场的拉格朗日拟序结构直观地显示了漩涡场的时空演化过程,揭示了漩涡配对和共旋穿越等流动特征,同时也展示了后缘尾涡面卷起现象在漩涡演化过程中的作用.     

光学炮塔气动载荷的非稳态特性

采用耦合J-B模型的IDDES模型与双时间步LU-SGS方法开展炮塔非稳态气动载荷的数值仿真研究。炮塔流动会发生分离,天顶位置的分离角大于90°;当流动绕过炮塔时,形成马蹄涡、脱落涡街等非稳态流场结构,导致气动载荷也具有非稳态特性;炮塔顶点的脉动静压功率谱在1.6~40.0 kHz进入各向同性均匀湍流的惯性子区,基本满足Kolmogrov的-5/3定律;气动力以阻力为主,横向力的脉动幅值大,气动力矩则以俯仰力矩为主,滚转力矩的脉动幅值大,偏航力矩可以忽略不计;气动力和力矩的功率谱主要集中在1 kHz以下,存在多个尖峰频率,主频约为230 Hz (斯特劳哈尔数为0.15)。在ATP系统设计之初,需要考虑光学炮塔所受气动载荷的非稳态特性,并规避尖峰频率尤其是主频的谐振破坏问题。     

Flow visualization for an unconventional forebody

Some results of flow visualization are described for an unconventional fuselage with Erickson-like forebody. The experiment includes force measurement, surface oil flow visualization, and laser sheet flow visualization. Some results are also obtained from a CFD code for solving laminar Navier-Stokes equations. Although there are some differences between the model in the experiment and the model in the computation, the location of vortex on the models exhibits good agreements. The investigation in this paper shows that varying the forebody shape of fuselage can change the flow characteristics greatly and the Erickson-like forebody has potential to improve the lateral-direction stability of the aircraft at high angles of attack.     

Scattering and absorption of sound at flow duct expansions

The scattering of plane acoustic waves at area expansions in flow ducts is analysed using the vortex sheet model where the flow at the expansion is modelled as a jet, with a vortex sheet emanating from the edge. Of particular interest is the influence of the flow field on acoustic scattering and absorption.First, it is demonstrated that the stability properties of the shear layer can be simulated by modifying the edge condition within the vortex sheet model. To this end the accuracy for the region where the shear layer is changing from unstable to stable is improved by introducing a gradually relaxed Kutta edge condition with empirically derived coefficients. For low Strouhal numbers the vortex sheet model applies and for higher Strouhal numbers the two models converge.Second, it is demonstrated that the acoustic transmission through the jet expansion region can be determined by neglecting the scattering there. Incorporating this assumption, the vortex sheet model reproduces well the experimental results on transmission and absorption for an area expansion. This result supports the assumption that the main part of the scattering occurs at the area expansion at least for the low-frequency range. Furthermore, the influence of the flow field is particularly strong for small Strouhal numbers.     

Study of aerodynamic structure of flow in a model of vortex furnace using Stereo PIV method

The aerodynamic structure of flow in a lab model of a perspective design of vortex furnace was studied. The chamber has a horizontal rotation axis, tangential inlet for fuel-air jets and vertical orientation of secondary injection nozzles. The Stereo PIV method was used for visualization of 3D velocity field for selected cross sections of the vortex combustion chamber. The experimental data along with “total pressure minimum” criterion were used for reconstruction of the vortex core of the flow. Results fit the available data from LDA and simulation.     

Application of PSP to low density gas flows

Recently optical pressure measurement systems using pressure sensitive paints (PSP) have actively developed to measure continuous pressure distributions on solid surfaces. However, the pressure range has been almost limited above 130 Pa (about 1 Torr) and there is no application to lower pressure range because the pressure sensitivity seems to be not so high in that range. In this study, we have applied three types of PSP [two types are composed by organic dye and polymer (luminophore/binder); PtOEP/GP197 and PtTFPP/poly(TMSP), and another one is Bath-Ru adsorbed on anodized aluminum] to the rarefied gas flow mainly lower than 130 Pa and examine those fundamental properties such as pressure sensitivity, leading to selection of the most suitable PSP among them for the low-pressure range. Since PtTFPP/poly(TMSP) has the highest sensitivity, it is applied successfully to the measurement of the two-dimensional pressure distribution on the surface interacting with a low density supersonic free jet.     

高超声速椭圆锥边界层横流转捩特性大涡模拟

横流效应显著影响高超声速飞行器的三维边界层转捩过程, 深化对该流动机制的认识有助于提升和改善飞行器气动性能及热力学环境. 针对HIFiRE5椭圆锥绕流问题, 采用大涡模拟方法计算分析了超声速边界层横流转捩特性, 并揭示其中的流动机理. 参考HIFiRE5风洞模型试验条件, 数值模拟中椭圆锥来流入口处施加人工速度扰动以激发边界层内不稳定扰动波, 进而预测了高超声速边界层流动横流失稳、转捩过程等基本流动特征, 并基于转捩热流分布形态对比, 获得了与试验数据基本吻合的计算结果. 研究发现, 椭圆锥中心线流动汇聚形成的流向涡结构非常容易失稳, 另外在中心线及侧缘之间的中部区域存在较强的横流不稳定性, 两种机制共同作用影响边界层转捩过程. 此外, 分析了来流扰动幅值对边界层横流失稳转捩的影响, 并发现静来流条件下, 横流区域出现两组独立的定常横流涡结构, 而强噪声来流条件下, 中心线主涡和中部横流涡均发生失稳转捩, 且在椭圆锥表面形成多峰状的转捩阵面. 最后, 深入分析流场的压力脉动动力学特性, 揭示了三维边界层发生失稳转捩的非线性演化机制.      

Prediction of aerodynamic noise reduction by using open-cell metal foam

As the speed of high-speed train (HST) increases continuously, aerodynamic noise has become more remarkable compared with the wheel/rail noise, which affects the inhabited environment along the railway and the riding comfort. This paper preliminarily investigates the feasibility of using open-cell metal foam covering layer to reduce the low Mach number aerodynamic noise generated by the flow around a circular cylinder which is the typical section of pantographs. The aerodynamic noises radiated from the circular cylinder with and without metal foam are calculated. The hybrid method combining two-dimensional large eddy simulation (LES) with Ffowcs Williams–Hawkings (FW–H) equation is employed. The calculated Strouhal number, time-averaged drag coefficient, base pressure and overall sound pressure level agree well with some available experimental data. Then, the influences of metal foam porosity, pore density, thickness of covering layer and the speed of train on the aerodynamic noise and the aerodynamic forces are investigated, and some detailed comparisons of flow field are made. The numerical results indicate that as a passive scheme, the open-cell metal foam with high porosity can modify the flow, adjust the vortex shedding frequency and regularize the wake, leading to a significant reduction of aerodynamic noise. The results are expected to provide useful information for the control of aerodynamic noise using this new material.     

自由旋涡气动窗口全流场的数值模拟

建立自由旋涡气动窗口全流场仿真模型,对大密封压比气动窗口的全流场展开数值研究,得到自由旋涡气动窗口的流场结构,发现大密封压比气动窗口形成的自由旋涡射流在光束输出通道内无明显的波系结构.根据模拟结果对自由旋涡气动窗口的性能进行优化,对自由旋涡喷管上壁面型线进行二次粘性修正.优化自由旋涡射流场后,激光器输出光束通道内压力分布稳定上升;增加扩压器外端壁吹气1.19MPa、内端壁吹气1.68MPa时,自由旋涡射流总能提高,气动窗口密封压力从37.5torr降低至6torr.该研究结果对自由旋涡气动窗口技术的发展具有参考意义.     

S型叶尖小翼对风力机流场特性影响的研究

在额定尖速比下,结合滑移网格的大涡模拟方法,对有无叶尖S型小翼的三叶片水平轴风力机流场特性进行了数值研究,结果表明:加装S型小翼后,改善了风轮上游的速度及压力分布情况,汲取了更多的风能;风轮压力面及吸力面的最大压差由1359 Pa提高到1756 Pa,使风轮功率放大;叶尖涡结构扩展规律与PIV(Particle Image Velocimetry)实验结果一致,叶尖涡轴向速度由15.6 m/s降低到了13.3 m/s,涡漩能量减少,叶尖涡涡量强度减弱,降低了气动噪声。