用3,6-双[(2-胂羧基苯)偶氮]-4,5-二羟基-2,7-萘二磺酰苯胺改性硅胶富集、分离痕量元素的研究

本文介绍了3,6-双[(2-胂羧基苯)偶氮]-4,5-二羟基-2,7-萘二磺酰苯胺(偶氮胂-DAL)改性硅胶的制备方法,研究了它的性质及其富集,分离Ti(Ⅳ),Zr(Ⅳ)、Hf(Ⅳ)的工作。研究结果表明,偶氮胂-DAL改性硅胶在6mol/L HClpH4.0的溶液中是稳定的;其对Zr(Ⅳ)的最大吸附量为20.9μmol/g;在1mol/L HCl介质中,经偶氮胂-DAL-SG柱预富集处理后,可将Zr(Ⅳ)、Hf(Ⅳ)与Ti(Ⅳ)、贵金属、常见过渡元素,稀土元素等金属离子直接分离,用普通分光光度法测定人工水样中Zr(Ⅳ)的下限可达10~(-9)g/g。     

A selective and sensitive film for electrocatalysis of ascorbic acid based on polypyrrole doped with nitroso-R(1-nitroso-2-naphthol-3,6-disulfonic acid disodium)

An electrocatalytic detection of ascorbic acid on a nitroso-R modified polypyrrole electrode has been studied. This functionalized polypyrrole film was electropolymerized by constant potential method on a platinum electrode from solution including pyrrole as monomer and nitroso-R as anionic dopant. Electrocatalytic currents of ascorbic acid were linearly dependent on its concentration in the range of 0.12–18.54 mM, with detection limit and relative standard deviation of 0.02 mM and 1.32%, respectively. This modified electrode can be used for determination of ascorbic acid in various pharmaceutical samples. Also, electrochemical behavior of this system was studied by various methods (RDE voltammetry, chronoamperometry, hydrodynamic amperometry and cyclic voltammetry).     

N-Acetylacetone-anthranilic acid as a gravimetric reagent for copper(II)

N-Acetylacetone-anthranilic acid has been employed as a reagent for the gravimetric determination of copper(II). The solid copper(II) chelate formed possesses 1:1 metal-ligand stoichiometry and is found to exist as an unsolvated dimer. The complex has a magnetic moment of 1.88 B.M. at 298 K. A non-planar dimeric structure is suggested to explain the observed facts.     

Spectrofluorimetric determination of copper(II) by its static quenching effect on the fluorescence of 4,5-dihydroxy-1,3-benzenedisulfonic acid

A spectrofluorimetric method has been developed for the determination of trace Cu(II) in real samples with 4,5-dihydroxy-l,3-benzenedisulfonic acid (Tiron) as a fluorimetric reporter. Tiron is very soluble in water and is a good fluorimetric reagent. However, as Tiron was complexed with Cu(II), the fluorescence intensity decreased proportionally to the concentration of Cu(II) by a static quenching effect. The excitation wavelength and the fluorescence wavelength of Tiron were 294 and 350 nm, respectively, as it was caused by a quenching effect from Cu(II) at pH 8.0. The highest sensitivity was shown at Tiron concentration of 5.0x10(-5) M. To enhance the quenching effect, the Cu(II)-Tiron complex solution was heated up to 80 degrees C for 90 min. As for Cu(II), the interference by Co(II) was very serious, which was eliminated by oxalate ion. The linear response to Cu(II) was shown at the concentration range between 5.0x10(-7) and 1.0x10(-5) M. With this proposed method, the detection limit of Cu(II) was 3.83(+/-0.09)x10(-7) M. Recoveries of Cu(II) in the diluted brass samples and the stream water samples were almost 100%. Based on results from the experiment, this proposed technique could be applied to the practical determination of Cu(II) in real samples.     

Determination of trace amounts of vanadium with a new reagent [1-(3-methoxysalicylidene-amino)-8-hydroxy-3,6-naphthalene disulfonic acid, disodium salt] by fluorescence quenching method

A fluorescence quenching method is described for the determination of trace amounts of vanadium(V) based on the formation of a complex in acidic medium with a new reagent [1(3-methoxysalicylideneamino)-8-hydroxy-3,6-naphthalene disulfonic acid, disodium salt]. The fluorescence emission is measured at 415 nm (wavelength of excitation 360 nm), and the experimental variables and interferences in this determination have been studied. The detection limit is 12.5 ng/ml and linear range is between 50 and 600 ng/ml. The method has been applied to determine trace vanadium(V) in steel and cast iron.     

Cu(II)-3-(5-chlor-2-hydroxy-3-sulfophenylazo)-6-(2,4,6-tribromophenylazo)-4,5-dihydroxynaphthalene-2,7-disulfonic Acid-Co(II) binuclear complexation and its application to the selective determination of cobalt at ng/ml level.

The chromophore, 3-(5-chlor-2-hydroxy-3-sulfophenylazo)-6-(2,4,6-tribromophenylazo)-4,5-dihydroxynaphthalene-2,7-disulfonic acid (CSTDD) was used to complex Cu(II) and Co(II) in aqueous solution at pH 9.43. A binuclear complex of Cu-CSTDD-Co was formed and showed a high selectivity for the determination of Co(II). The spectral correction technique was applied to characterize the complexes. The results showed the formation of complexes of Cu(CSTDD), Co(CSTDD)3 and Cu2(CSTDD)2Co. The quantitative analysis of Co(II) at ng/ml level was carried out by the light-absorption ratio variation approach (LARVA). The results showed that the technique is satisfactory to determine Co(II) at trace level in water samples with a detection limit of 2.3 ng/ml.     

Compartmental Schiff-base ligands as selective double-loaded extractants for copper(II)

The Robson compartmental macrocyclic ligand derived from the condensation of derivatives of 2,6-diformylphenol and diamines has been prepared for the first time in its free ligand form; competitive three-phase transport and two-phase extraction studies confirm high double-loaded selectivity for the binding and delivery of Cu(II).     

Single glass nanopore-based regenerable sensing platforms with a non-immobilized polyglutamic acid probe for selective detection of cupric ions

A single glass capillary nanopore-based sensing platform for rapid and selective detection of cupric ions is demonstrated by utilizing polyglutamic acid (PGA) as a non-immobilized probe. The detection is based on the significant decrease of ionic current through nanopore and the reversal of ion current rectification responses induced by the chelated cupric ions on the probes when in the presence of cupric ions. PGA shows high selectivity for detecting cupric ions rather than other metal ions. The sensitivity of the sensing platform can be improved about 1–2 orders of magnitude by employing asymmetric salt gradients during the measurements. And the PGA-based nanopore sensing platform shows excellent regenerability for Cu²⁺ sensing applications. In addition, the method is found effective and reliable for the detection of cupric ions in real samples with small volume down to 20 μL. This nanopore-based sensing platform will find promising practical applications for the detection of cupric ions.     

N,N'-disalicylidene-1,3-diaminopropane as a selective chelating titrant for copper(II)

This study was carried out to develop a new complexometric titration method for determination of copper. For this purpose, the standard solutions of copper(II) (10(-3)-10(-5) M) were potentiometrically titrated using N,N'-disalicylidene-1,3-diaminopropane (Schiff base) as titrant and copper(II)-selective electrode for end-point indication in both ammonium acetate and ammonia/ammonium chloride buffer media. The stoichiometry of titration reaction and interference effects of some metal ions on titration of copper were discussed. There was a good agreement between the results obtained by the proposed titration method and ethylenediaminetetraacetic acid (EDTA) titration method. The accuracy and precision of Schiff base method were tested by five replicate determinations both on the standard solution of copper(II) and standard reference materials. The results have indicated that the percentage of copper in alloys can be safely determined by using the Schiff base method without interference from many other metals in alloys.     

A new nano-composite electrode as a copper (II) selective potentiometric sensor

A macrocyclic ligand “7,10,13-triaza-1-thia-4,16-dioxa-20,24-dimethyl-2,3;17,18-dibenzo-cyclooctadecane-6,14-dione” as an efficient ionophore was used into a new Cu²⁺ nano-composite potentiometric carbon paste sensor containing multi-walled carbon nanotubes (MWCNTs), nanosilica particles, and room temperature ionic liquid (1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide, [BMP]Tf₂N). This potentiometric sensor responds to copper ions in a wide linear dynamic range of 4.50 × 10^?8 to 1.00 × 10^?2 mol L^?1 with Nernstian slope of 29.64 ± 0.10 mV per decade. The detection limit of 2.34 × 10^?8 mol L^?1 was obtained at the pH range 3.5–6.0. It has a fast response with response time of about 10 s, and can be used for at least 16 weeks without any considerable divergence in the potentials. The suggested sensor thus allows sensitive, selective, simple, low cost, and stable electrochemical sensing of Cu²⁺ ions in the presence of a large number of alkali, alkaline earth, transition and heavy metal ions. This sensor was successfully applied in the determination of copper ions in water and waste water samples.     

Crescent aromatic oligothioamides as highly selective receptors for copper(Ⅱ) ion

A series of crescent aromatic oligothioamides(4, 6, 8, 15, and 18) bearing different number of sulfur atoms were designed and synthesized via thionation of their corresponding aromatic oligoamides(3, 5, and 7) using Lawesson's reagent. The X-ray structure of a trimeric analogue(13) revealed the presence of intramolecular three-center hydrogen bonds that are responsible for the rigidification of the molecular backbone. The extraction by these novel receptors toward some representative heavy metal cations(Zn2+, Cd2+, Co2+, Ni2+, Pb2+, and Cu2+) and alkali and alkaline earth metal cations(Li+, Na+, K+, Rb+, Cs+, Ca2+, and Sr2+) demonstrated high efficiency(83.5%–96.4%) and superior selectivity for Cu2+ over other selected metal cations. Particularly, the extractability was correlated to both the number of sulfur atoms and orientation of thiocarbonyl groups as revealed in the order: 6 4 18 15. This is in stark contrast to the oligoamides that only gave much lower extractability(5.9%–16.4%), suggestive of the importance of replacement of carbonyl oxygen atoms with sulfur atoms in the extraction of Cu2+. The complexation behavior of 4, 6, and 8 with Cu2+ was also examined by UV-Vis and NMR techniques.     

Synthesis of 3-(pyridine-2-yl)-4,5-dihydro-1H-pyrazole-1-thiocarboxamides and their copper(II) complexes

New organic ligands 3-(pyridine-2-yl)-4,5-dihydro-1H-pyrazole-1-thiocarboxamides (L) have been synthesized by a two or three step reaction sequence starting from substituted benzaldehydes and 2-acetyl pyridine. Copper(II) complexes with LCuCl₂ composition were obtained by the reactions of these ligands with CuCl₂·2H₂O. The crystal structure of two synthesized complexes has been determined by X-ray analysis. Copper atoms located in a strongly distorted square piramidal environment and coordinated by pyrazoline and pyridine nitrogen atoms, thiocarbamoyl sulfur atom and two chloride-anions. All complexes undergo reversible or quasi-reversible electrochemical reduction at 0.45–0.28 V with the formation of Cu(I) containing intermediates. The cytotoxicity of copper containing complexes, comparable to cisplatin and doxorubicin, was demonstrated using cancer cell lines MCF-7, A549 and HEK293.     

A heterobimetallic ruthenium(II)-copper(II) donor-acceptor complex as a chemodosimetric ensemble for selective cyanide detection

A trinuclear heterobimetallic Ru(II)-Cu(II) donor-acceptor complex, [Ru(II)((t)Bubpy)(CN)(4)-[Cu(II)(dien)](2)](ClO(4))(2) ((t)Bubpy = 4,4'-di-tert-butyl-2,2'-bipyridine; dien = diethylenetriamine) (1), has been synthesized and successfully used as an chemodosimetric ensemble for the specific detection of cyanide in aqueous DMF. X-ray crystallography, solid and solution IR spectroscopy, and conductivity measurements reveal that complex 1 is a one-dimensional polymer in the crystalline state and dissociates into its [Ru(II)((t)Bubpy)(CN)(2)[(CN)Cu(II)(dien)L](2)](2+) (L = solvent) monomeric units in polar solvents. The MLCT transition and luminescence properties of the solvatochromic [Ru(II)((t)Bubpy)(CN)(4)](2)(-) donor are perturbed by the coordination of two Cu(II) acceptors but restored in the presence of CN(-). Spectroscopic and mass spectrometric studies confirm the cleavage of the cyano bridge between Ru(II) and Cu(II) of the chemodosimetric ensemble after the binding of cyanide to the Cu(II) centers. The overall binding constant, K(B), between 1 and CN(-) is measured to be (7.39 +/- 0.23) x 10(6) M(-2). A detection limit of 1.2 microM (0.03 ppm) of CN(-) in aqueous DMF (pH 7.4) is achievable. Thermodynamic evaluation shows that the analyte specificity of chemodosimeter 1 is attributable to the relative stability of the donor-acceptor complex to that of adducts formed between the acceptor metal center and the analytes.     

Solid-state Cu (II) ion-selective electrode based on polyaniline-conducting polymer film doped with copper carmoisine dye complex

A pencil graphite electrode coated by copper (II)–carmoisine dye complex in polyaniline (emeraldine base form) matrix (termed as PGE/PA/Cu-Car) was prepared and used as copper ion-selective electrode. The introduced electrode was found to have high selectivity toward copper ion (II) and exhibited wide working concentration range, low response time, and good shelf life. The sensor electrode showed a linear Nernstian response over the range of 5.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a slope of 29.7 ± 1 mV per decade change in concentration. A detection limit of 2.0 × 10⁻⁶ M was obtained. The optimum pH working range of the electrode was found to be 4.0–7.0.     

Highly selective probe of a copper(II) complex based on a coumarin derivative for hydrogen sulfide detection

Abstract

A fluorescent probe 1 containing copper(II) had been designed and synthesized based on a coumarin derivative. The molecular structure of probe 1 was characterized by ¹H NMR, HRMS, IR, and elemental analysis. The interactions of 1 with biologically important anions and amino acid were determined by UV–Vis, fluorescence, and HRMS titration experiments. Results indicated that probe 1 showed the highest binding ability for HS^? among studied anions (AcO^?, H₂PO₄^?, F^?, Cl^?, Br^?, and I^?) and cysteine in pure dimethyl sulfoxide (DMSO) and HEPES buffer solution. As we expected, the response of UV–Vis spectra in aqueous solution was stronger than that of pure DMSO solvent. In addition, the binding ability for HS^? was not hindered by the existence of other anions. HRMS titration experiment showed that the interacted mechanism was that the copper(II) ion in 1 was captured by HS^? and then free ligand released. Furthermore, the detection limit of probe 1 with HS^? was carried out through UV–Vis titration showing 1 to be highly sensitive for HS^?.     

Azobenzene coupled chromogenic receptors for the selective detection of copper(II) and its application as a chemosensor kit

Azobenzene-based receptors 1-4 as colorimetric sensing materials were synthesized and their sensing properties were examined. In solution, the proposed sensing materials give rise to a large cation-induced hypochromic shift for Cu²⁺ resulting in a change from red to pale-yellow, whereas no significant color change was observed upon addition of other selected metal ions. The use of the silica gel plate modified with immobilization of receptor 4 to detect Cu²⁺ was also reported.     

Copper(I) sulphide-impregnated silicone rubber membranes as selective electrodes for copper(II) ions

Silicone rubber membranes impregnated with copper(I) sulphide have been developed as selective electrodes for coppefr(II) ions. The internal electrode and solution were eliminated. The Nernst equation was satisfied in the concentration range from 10(-1) to 10(-6)M copper(II) and the analytical range was from 10(-1) to 10(-7)M. The interference of other ions was examined. Other resins were compared with silicone rubber as inert matrices.     

Determination of arsenic(III) and copper(II) by stripping voltammetry in a mixed EDTA-phosphoric acid supporting electrolyte

The effect of the composition of a supporting electrolyte containing EDTA and H₃PO₄, the parameters of the analytical cycle, and the concentration of a depolarizer on the electrochemical behavior of arsenic(III) and copper(II) was studied by anodic stripping voltammetry at a gold-graphite electrode. The optimum conditions for determining these elements were found. Different techniques are proposed for the isolation of the analytical signals from the total voltammetric signal using postelectrolysis and subtracting voltammograms. It is shown that 0.007 µg/mL arsenic(III) can be determined in the presence of 30-fold amounts of copper(II) and 0.007 µg/mL copper(II) can be found in the presence of 40-fold amounts of arsenic(III).Translated from Zhurnal Analiticheskoi Khimii, Vol. 60, No. 2, 2005, pp. 179–186.Original Russian Text Copyright © 2005 by Kamenev, Lyakhov, Orlov.This revised version was published online in April 2005 with corrections to the author names and book review format.