弹光调制器准单色光波偏振测量与仿真

弹光调制器(Photoelastic Modulator,PEM)互差频调制的新型偏振测量方法,能够同时实现三个斯托克斯光谱偏振参数测量,克服了现有方法的无法用阵列探测器有效采集,调制频率高的缺点,保留了原有弹光调制器偏振测量的优点。文章以光学系统的准单色光的偏振特性以及常用的偏振分析方法为基础,引入了Stokes矢量来表示入射光波的偏振特性。分析了弹光调制器实现偏振测量新方法的原理,利用三个弹光调制器工作在互相差异的频率上,对偏振光进行差频调制,产生载有偏振信息的低频分量,再通过锁相放大即可得到偏振信息,并给出利用MATLAB模拟仿真实现Stokes参量复原的过程。理论分析及仿真结果证明了该方法在理论上的可行性。     

Caustics method in dynamic fracture problem of orthotropic materials

Caustics method is a powerful optical technique in fracture mechanics because of its high sensitivity to stress gradients. In this paper, it is applied to resolve dynamic fracture problems in orthotropic composites. Considering most orthotropic materials are opaque, reflective caustics method is derived here by combining the fundamental principle of caustics method with the mechanical properties of orthotropic materials. Meanwhile, corresponding experiments are carried out for typical glass fiber-reinforced composites, where mode I and mixed-mode fracture states are taken into account. By recording and analyzing shadow spot patterns during the crack propagation process carefully, crack onset time, dynamic fracture toughness and crack growth velocity of orthotropic composite are determined. These results will be useful to evaluate the dynamic fracture properties of composites and further to optimize their designs.     

Vibration of moderately thick square orthotropic stepped thickness plates

Numerous studies that address the vibration of stepped thickness plates are reported in the literature. Predominately, classical plate theory has been used to formulate studies for both isotropic and anisotropic stepped plates. Mindlin plate theory has been employed to obtain results for thick isotropic stepped thickness plates. Exact solutions, Rayleigh-Ritz, differential quadrature and finite element methods have been employed to compute results for frequency of vibration. Results for frequency of vibration for thick orthotropic stepped thickness plates are presented here using orthorhombic material properties of aragonite. The finite element method has been used to compute frequencies and determine mode shapes for simply supported and clamped square Mindlin plates.     

Photoelastic effect and mirage deflection in anisotropic materials

The collinear mirage technique is widely used to measure the thermal diffusivity of semi-transparent materials. However, in a recent paper [A. Salazar, M. Gateshki and A. Sánchez-Lavega: Appl. Phys. Lett. 76, 2665 (2000)], it was shown that for isotropic materials, because of the influence of photoelastic effect, the method was sensitive to the polarization state of the probe beam. The present paper extends the previous work to include anisotropic materials. In particular, we focus on the experimental conditions under which the thermal diffusivity of each crystal system can be measured using the phase method. Our theoretical model indicates that while the thermal diffusivity of isotropic materials can be measured using an unpolarized probe beam, for anisotropic materials, even the use of an unpolarized probe beam does not guarantee the validity of the method in all crystal systems. Experimental measurements performed on cubic, hexagonal and monoclinic crystals confirm the validity of the model. Received: 17 March 2001 / Accepted: 17 March 2001 / Published online: 25 July 2001     

Acoustic scattering characteristics of a thick-walled orthotropic cylindrical shell at oblique incidence

The method of wave function expansion is adopted to study the scattering of a plane harmonic acoustic wave incident at an arbitrary angle upon an arbitrarily thick cylindrically orthotropic homogeneous cylindrical shell submerged in and filled with compressible ideal fluids. A laminate approximate model and the so-called state space formulation in conjunction with the classical transfer matrix (T-matrix) approach are employed to present an analytical solution based on the three-dimensional exact equations of anisotropic elasticity. The solution is used to correlate the perturbation in the material elastic constants of an air-filled and water-submerged aluminium cylindrical shell to the sensitivity of resonances associated with various modes of wave propagation appearing in the backscattered amplitude spectrum (i.e., axially guided, Lamb, Rayleigh and Whispering Gallery waves). The effects of shell wall thickness as well as inner fluid loading on the frequency response of the shell are also examined. A limiting case is considered and good agreement with the solution available in the literature is obtained.     

Effect of the non-homogenity on the composite infinite cylinder of orthotropic material

In this Letter, the solution of non-homogeneous orthotropic elastic cylinder for plane strain problems is developed. The dynamical problem of an orthotropic cylinder containing: (i) an isotropic core and (ii) a rigid core are considered. The elastic constants and density are taken as a power function of the radial coordinate. Analytical expressions for the component of the displacement and the components of the stresses in different cases are obtained. The numerical calculations are carried out for the component of displacement and the components of the stresses through the radial of the cylinder. The results indicate that the effect of inhomogeneity is very pronounced. Those cases have been illustrated and discussed by figures.     

Theoretical investigation of Stoneley-wave attenuation and dispersion in a fluid filled fracture in transversely isotropic formation

The wave motion in a fluid-filled fracture embedded in an anisotropic medium is investigated using the technique of partial waves. A model is derived to calculate the complex dispersion relation of the Stoneley-wave mode in a fluid layer between two infinite transversely isotropic half-spaces. The effect of the anisotropic parameters on the Stoneley-wave in the fracture is investigated. The numerical results indicate that the velocity of the Stoneley-wave mode has significant dependence on the transversely isotropic constants. For a weakly anisotropic medium, the Stoneley-wave dispersion is almost the same as in an isotropic medium.     

Guided circumferential waves in orthotropic cylindrical curved plate and the mode conversion by the end-reflection

In ultrasonic nondestructive inspection of large-diameter pipes and curved plate, longitudinal cracks are detected more efficiently by using guided circumferential waves. In the present, the study of guided circumferential waves and their application in detecting longitudinal defect were relative adequate when pipe material is isotropic. Based on linear three-dimensional elasticity, an orthogonal polynomial series expansions approach is used for determining the guided circumferential waves dispersion curves in homogeneous infinitely long orthotropic hollow cylinders. Results are compared with those published earlier and with the finite element simulation to check up the accuracy and range of applicability of this polynomial approach. Through the analysis of the displacements distributions and finite element simulation, the mode conversion of guided circumferential waves by end-reflection in cylindrical curved plate is discovered.     

Lattice-Boltzmann simulations of dynamic interfacial tension due to soluble amphiphilic surfactant

An amphiphilic Lattice-Boltzmann approach is adopted to model dynamic interfacial tension due to non-ionic surfactant. In the current system, the surfactant adsorption kinetics is diffusion dominated and the interface separates two immiscible fluids. A rotational relaxation time and a diffusive/viscous relaxation time are associated with the surfactant. The model results are compared with experimental data for the dynamic interfacial tension of a pendant oil droplet in water, with oil soluble surfactant. We demonstrate how to adapt and calibrate the model to capture the adsorption timescale of the surfactant and the magnitude of interfacial tension reduction due to surfactant. A scheme to overcome numerical instabilities due to the relatively low surfactant concentration, is devised. We are able to qualitatively match the Frumkin equation of state for the interfacial tension.     

正交异性钢桥面板声发射波三维谱元法模拟及损伤定位*

针对大跨度桥梁正交异性钢桥面板的疲劳损伤评估与结构健康监测需求,开展基于声发射波场谱元法模拟的大型复杂板类结构损伤定位研究。采用Legendre高阶插值三维时域谱元法模拟声发射波在正交异性钢桥面板中的传播过程,验证了其内部显著的反射、衍射和频散现象,并代替人工预断铅实测试验获得大量声发射数据。然后,利用赤池信息准则判定声发射波到达各传感器的时间,通过高斯过程回归建立到达时差与声发射源位置的关系模型,用于未知损伤的定位监测。数值模型实验结果表明,赤池信息准则和高斯过程回归改进的时差图法在正交异性钢桥面板中的平均定位误差为37.3 mm(25 dB信噪比工况),平板的定位精度高于U肋。谱元法模拟有望代替繁琐的预断铅实测试验,提升声发射时差图系列损伤定位方法的实用性。     

Diffraction gratings of isotropic negative-phase velocity materials

Diffraction of electromagnetic plane waves by the gratings made by periodically corrugating the exposed planar boundaries of homogeneous, isotropic, linear dielectric-magnetic half-spaces is examined. The phase velocity vector in the diffracting material can be either co-parallel or anti-parallel to the time-averaged Poynting vector, thereby allowing for the material to be classified as of either the positive- or the negative-phase velocity (PPV or NPV) type. Three methods used for analyzing dielectric gratings — the Rayleigh-hypothesis method, a perturbative approach, and the C formalism — are extended here to encompass NPV gratings by a careful consideration of field representation inside the refracting half-space. Corrugations of both symmetric as well as asymmetric shapes are studied, as also the diversity of grating response to the linear polarization states of the incident plane wave. The replacement of PPV grating by its NPV analog affects only nonspecular diffraction efficiencies when the corrugations are shallow, and the effect on specular diffraction efficiencies intensifies as the corrugations deepen. Whether the type of the refracting material is NPV or PPV is shown to affect surface wave propagation as well as resonant excitation of surface waves.     

Fracture analysis of a functionally graded interfacial zone between two dissimilar homogeneous materials

In this paper the plane elasticity problem for a functionally graded interfacial zone containing a crack between two dissimilar homogeneous materials has been considered. It is assumed that in the interfacial zone the reciprocal of the shear modulus is a linear function of the coordinate, while Possion’s ratio keeps constant. By utilizing the Fourier transformation technique and the transfer matrix method, the mixed boundary problem is reduced to a system of singular integral equations that are solved numerically. The influences of the geometric parameters and the graded parameter on the stress intensity factors are investigated. The numerical results show that the graded parameters, the thickness of interfacial zone, the crack size and location have significant effects on the stress intensity factors.     

Stability and vibration of isotropic,orthotropic and laminated plates according to a higher-order shear deformation theory

A higher-order shear deformation theory is used to determine the natural frequencies and buckling loads of elastic plates. The theory accounts for parabolic distribution of the transverse shear strains through the thickness of the plate and rotary inertia. Exact solutions of simply supported plates are obtained and the results are compared with the exact solutions of three-dimensional elasticity theory, the first-order shear deformation theory, and the classical plate theory. The present theory predicts the frequencies and buckling loads more accurately when compared to the first-order and classical plate theories.     

Evaluation of imaging in planar anisotropic and isotropic dendritic left-handed materials

Carbon nanotubes (CNTs) with totally hollow channels and/or totally filled copper nanowires have been fabricated by methane decomposition using copper microgrid as a catalyst at 1173 K. The formation mechanism of CNTs with totally hollow channels is carbon precipitation at carbon-metal interface via the preferable surface diffusion mode of carbon. The selectivity of these CNTs can be improved by increasing the purity of copper catalysts and adding hydrogen in the feed gas. To form long and continuous copper nanowires up to 8–10 μm the filling of copper in the CNT channel requires the liquid or quasi-liquid state capillary adsorption of nanosized copper at 1173 K under the thermal driving force. The filling volume ratio of copper to total nano-channel of the CNTs is firstly increased to about 50%. The copper inside the CNTs is of single crystalline form and face centered cubic (fcc) structure. The method is useful for further controlled synthesis of CNTs with totally hollow channels and/or totally copper filled nanowires. PACS 81.07.De; 82.33.Ya     

Spatiotemporal mapping of surface acoustic waves in isotropic and anisotropic materials

We demonstrate a new method for a real-time imaging of surface acoustic waves at frequencies up to 1 GHz with picosecond temporal and micron spatial resolutions using an ultrafast optical pump and probe technique combined with a common path interferometer. Using samples with isotropic or anisotropic substrates coated with metallic thin films, we observe the propagation of Rayleigh-like modes and surface-skimming bulk modes as well as resolving surface phonon focusing effects. In addition we image surface acoustic wave propagation in a laterally inhomogeneous sample.     

The buckling and frequency of flexural vibration of rectangular isotropic and orthotropic plates using Rayleigh's method

A simple approximate formula for the natural frequencies of flexural vibration of isotropic plates, originally developed by Warburton using characteristic beam functions in Rayleigh's method, is modified to apply to specially orthotropic plates and extended to include the effect of uniform, direct inplane forces. The initial buckling problem is treated simply by equating the frequency expression to zero. The approach permits the ready determination of reasonably accurate natural frequencies and/or buckling loads for a given plate involving any combination of free, simply supported or clamped edges, without requiring the aid of a sophisticated calculating device or a knowledge of plate, vibration or buckling theory. To illustrate the applicability and accuracy of the approach, numerical results for a number of specific plate problems are presented.     

Femtosecond laser ablation profile near an interface: Analysis based on the correlation with superficial properties of individual materials

Femtosecond laser ablation of materials is turning to be an important tool for micromachining as well as for selective removal of biological tissues. In a great number of applications, laser ablation has to process through interfaces separating media of different properties. The investigation of the ablation behavior within materials and passing through interfaces is the main aim of this study. Especially, the analysis of the discontinuity in the ablation profile close to interfaces between distinct materials can reveal some of the phenomena involved in the formation of an ablated microcavity geometry. We have used a method that correlates the ablation cross sectional area with the local laser intensity. The effective intensity ablation properties were obtained from surface ablation data of distinct materials. The application of this method allows the prediction of the occurrence of a size discontinuity in the ablation geometry at the interface of distinct media, a fact which becomes important when planning applications in different media.     

Fe/ZnSe/Fe junctions: Interplay between interface structure and tunneling magnetoresistance

We investigate the electronic structure of Fe/ZnSe/Fe magnetic tunnel junctions for which interdiffusion and reconstruction at the interfaces are considered. Taking into account the ab initio potential profile throughout the different layers of the structure, we discuss about its implications on the tunnel conductance. Our results show that interface reconstruction drives changes in the electronic structure which, in turn, produce an increase of the kinetic energy of the conduction electrons, independently of their spin orientation. We suggest that this reconstruction underlies the low tunnel magnetoresistance (TMR), as it is observed in transport measurements when compared with the theoretical value estimated for sharp interfaces.