Coupling Ferricyanide/Ferrocyanide Redox Mediated Recycling Spent LiFePO4 with Hydrogen Production

Replacing the oxygen evolution reaction with thermodynamically more favorable alternative oxidation reactions offers a promising alternative to reduce the energy consumption of hydrogen production. However, questions remain regarding the economic viability of alternative oxidation reactions for industrial-scale hydrogen production. Here, we propose an innovative cost-effective, environment-friendly and energy-efficient strategy for simultaneous recycling of spent LiFePO₄ (LFP) batteries and hydrogen production by coupling the spent LFP-assisted ferricyanide/ferrocyanide ([Fe(CN)₆]⁴⁻/[Fe(CN)₆]³⁻) redox reaction. The onset potential for the electrooxidation of [Fe(CN)₆]⁴⁻ to [Fe(CN)₆]³⁻ is low at 0.87 V. Operando Raman and UV/Visible spectroscopy confirm that the presence of LFP in the electrolyte allows for the rapid reduction of [Fe(CN)₆]³⁻ to [Fe(CN)₆]⁴⁻, thereby completing the [Fe(CN)₆]⁴⁻/[Fe(CN)₆]³⁻ redox cycle as well as facilitating the conversion of spent LiFePO₄ into LiOH ⋅ H₂O and FePO₄. The electrolyzer consumes 3.6 kWh of electricity per cubic meter of H₂ produced at 300 mA cm⁻², which is 43 % less than conventional water electrolysis. Additionally, this recycling pathway for spent LFP batteries not only minimizes chemical consumption and prevents secondary pollution but also presents significant economic benefits.     

On the Criteria of Instability for Electrochemical Systems

Both cyclic-voltammetry-based and impedance-based experimental criteria that have been developed recently for the oscillatory electrochemical systems are critically appraised with two typical categories of oscillators.Consistent conclusions can be drawn by the two criteria for the category of oscillators that involve the coupling of charge transfer mainly with surface steps(e.g.ad-and desorption)such as in the electrooxidation of C1 organic molecules.Whereas,impedance-based criterion is not applicable to the category of oscillators that involve the coupling of charge transfer mainly with mass transfer(e.g.diffusion and convection) such as in the Fe(CN)6^3- reduction accompanying periodic hydrogen evolution.The reason is that the negative impedance cannot include the feedback information of convection mass transfer induced by the hydrogen evolution.However,both positive and negative nonlinear feedbacks,i.e., the diffusion-limited depletion and convection-enhanced replenishment of the Fe(CN)6^3- surface concentration,that coexist between the bistability,i.e.,Fe(CN)6^3- reduction with and without hydrogen evolution at lower and higher potential sides respectively,are all reflected in the crossed cyclic voltammogram(CCV).It can be concluded that the voltammetry-based criterion(in time domain)is more intuitive,less time-consuming and has a wider range of applications than the impedancebased one (in frequency domain).     

In situ monitoring of potential oscillations in the reduction of IO3− by electrochemical quartz crystal microbalance

Electrochemical quartz crystal microbalance (EQCM) has been employed to study the potential oscillatory mechanism for the IO₃⁻ reduction accompanying periodic hydrogen evolution. The new experimental results that were obtained by in situ EQCM monitoring clearly demonstrate the all key steps involved in the oscillation: the diffusion-limited depletion of IO₃⁻ by reduction, the formation, growth and departure of hydrogen bubbles on the surface, and the convection-induced replenishment of IO₃⁻ by the hydrogen evolution. In addition to the frequency response to the surface mass change as reported in the literature, our study first shows that simultaneous frequency responses to the changes of density and viscosity in the diffusion layer during the oscillation can also provide meaningful and even decisive information on the oscillatory mechanism for the oscillators involving the coupling of electrochemical reactions with diffusion and convection mass transfer.     

The electrochemical properties of thermophilic cytochrome P450 CYP119A2 at extremely high temperatures in poly(ethylene oxide)

The electrochemical measurements were carried out by using thermophilic cytochrome P450 CYP119A2 (P450st) modified with poly(ethylene oxide) (PEO) in PEO₂₀₀ as an electrochemical solvent. The PEO modified P450st gave clear reduction–oxidation peaks by cyclic voltammetry in oxygen-free PEO₂₀₀ up to 120 °C. The midpoint potential measured for the P450st was −120 mV vs. [Fe(CN)₆]⁴⁻/[Fe(CN)₆]³⁻ at 120 °C. The peak separation, ΔE, was 16 mV at 100 mV/s. The estimated electron transfer rate of PEO-P450st at 120 °C was 35.1 s⁻¹. The faster electron transfer reaction was achieved at higher temperatures. The electrochemical reduction of dioxygen was observed at 115 °C with the PEO-modified P450st system.     

Electrochemical Motion Tracking of Microorganisms Using a Large-Scale-Integration-Based Amperometric Device

Motion tracking of microorganisms is useful to investigate the effects of chemical or physical stimulation on their biological functions. Herein, we describe a novel electrochemical imaging method for motion tracking of microorganisms using a large-scale integration (LSI)-based amperometric device. The device consists of 400 electrochemical sensors with a pitch of 250 μm. A convection flow caused by the motion of microorganisms supplies redox species to the sensors and increases their electrochemical responses. Thus, the flow is converted to electrochemical signals, enabling the electrochemical motion tracking of the microorganisms. As a proof of concept, capillary vibration was monitored. Finally, the method was applied to monitoring the motion of Daphnia magna. The motions of these microorganisms were clearly tracked based on the electrochemical oxidation of [Fe(CN)₆]⁴⁻ and reduction of O₂.     

Stereo-electrochemistry by a self-assembled monolayer of sulfur-bridged calixthiophene on gold

Sulfur-bridged calixthiophene formed a self-assembled mono-molecular layer on polycrystalline gold, and it regulated an electrochemical electron transfer by the host–guest interaction between the cavity and reactants. 1,7,13,19,25-Tetrathia[1.₅](2,5)thiophenophane (thiacalix[5]thiophene) perfectly passivated the gold electrode for relatively large reversible metal complexes: [Fe(CN)₆]^4−/3− and [IrCl₆]^3−/2−. However, for mono-atomic ions, such as silver and some of the halogen ions, the electrode behaved reversibly. For copper reduction, a large activation overpotential was observed to induce an initial copper reduction in the cavity.     

Electrochemical and thermodynamic properties of hexacyanoferrate(II)/(III) redox system on multi-walled carbon nanotubes

Novel films consist of multi-walled carbon nanotubes (MWCNT) were fabricated by means of catalytic chemical vapor deposition (CVD) technique with decomposition of either acetonitrile (ACN) or benzene (BZ) using ferrocene (FeCp₂) as catalyst. The electrochemical and thermodynamic behavior of the ferrocyanide/ferricyanide, [Fe(CN)₆]^3−/4− redox couple on synthesized MWCNT-based films was investigated by means of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques at T = (278.15, 283.15, 293.15, and 303.15) K. The redox couple [Fe(CN)₆]^3−/4− behaves quasi-reversibly on fabricated MWCNT-based films and its reversibility is enhanced upon increasing temperature. Namely, the findings establish that with the rise in temperature the barrier for interfacial electron transfer decreases, leading, consequently, to an enhancement of the kinetics of the charge transfer process. According to thermodynamics the equilibrium of the redox process is shifted towards the formation of [Fe(CN)₆]³⁻ at elevated temperatures.     

Mapping concentration profiles within the diffusion layer of an electrode: Part II. Potentiometric measurements with an ultramicroelectrode

A platinum-disk ultramicroelectrode is used to monitor electrochemical potential variations inside the steady-state diffusion layer created by a larger electrode. The experimental potential variations result from combination of a pure electrochemical component (viz., as given by the Nernst law) with a smaller ohmic drop contribution, which varies linearly with the distance from the working electrode surface so that it can be readily eliminated. From the ensuing corrected potential variations, the concentration profiles of the electroactive species present within the diffusion layer can be reconstructed by application of the Nernst law. The validity and great interest of the method are demonstrated experimentally by the study of the one-electron reversible oxidation of the Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ couple in aqueous KCl solutions. As a correlation, this demonstrates also for the first time the validity of the Nernst layer approximation. The method is then applied to examine the specific structure of the diffusion layers, which result from the involvement of a conproportionation reaction during the second reduction of tetracyanoquinodimethane (TCNQ) in DMF.     

Electrochemical Motion Tracking of Microorganisms Using a Large‐Scale‐Integration‐Based Amperometric Device

Motion tracking of microorganisms is useful to investigate the effects of chemical or physical stimulation on their biological functions. Herein, we describe a novel electrochemical imaging method for motion tracking of microorganisms using a large‐scale integration (LSI)‐based amperometric device. The device consists of 400 electrochemical sensors with a pitch of 250 μm. A convection flow caused by the motion of microorganisms supplies redox species to the sensors and increases their electrochemical responses. Thus, the flow is converted to electrochemical signals, enabling the electrochemical motion tracking of the microorganisms. As a proof of concept, capillary vibration was monitored. Finally, the method was applied to monitoring the motion of Daphnia magna . The motions of these microorganisms were clearly tracked based on the electrochemical oxidation of [Fe(CN)₆]⁴⁻ and reduction of O₂.     

Preparation and characterization on the carbon nanotube chemically modified electrode grown in situ

Carbon nanotube chemically modified electrode (CNT-CME) was prepared by growing carbon nanotube (CNT) in situ on the pretreated graphite electrode (GE) via the catalytic chemical vapor deposition. The pretreated GE was prepared by ultrasonic immersion method using Ni(NO₃)₂ as the catalyst. The CNT growing on the CNT-CME was characterized by transmission electron microscope and scanning electron microscope. The obtained electrode electrochemical performance was characterized by cyclic voltammetry with the Na₂SO₄ solution and [Fe(CN)₆]³⁻/[Fe(CN)₆]⁴⁻ solution. The results showed that the obtained electrode has good current responsive sensitivity and good testing result accuracy, indicating that the obtained electrode may have great application in electrochemical testing field.     

Electrochemistry of a carotenoid self-assembled monolayer

A carotenoid self-assembled monolayer was prepared by dipping a gold electrode into a solution of 4^′-thioxo-β,β-caroten-4-one in acetonitrile. Electrochemistry of the surface layer was investigated by cyclic voltammetry in an aqueous solution. No electrochemical reaction was detected in the potential region between 0.5 and −0.6 V vs. SCE. The anodic reaction of adsorbed carotenoid occurs at 0.8 V, whereas the irreversible anodic desorption proceeds at 1.4 V in 0.01 M HClO₄. Formation of the surface layer resulted in a decrease of the charging current as well as in a strong inhibition of the electron transfer reaction for species such as Fe(CN)₆³⁻, Ru(NH₃)₆³⁺, and dissolved oxygen. Prolonged voltage cycling in the O₂ reduction range induced some changes in the surface layer characteristics that were tentatively accounted for by the cross-linking of adsorbed molecules under the effect of transient oxygen radicals.     

Development and Evaluation of Gold 3D Cylindrical Nanoelectrode Ensembles

Gold 3D cylindrical nanoelectrode ensembles （NEEs）, 100 nm in diameter and 500 nm in length were prepared by electroless template synthesis in polycarbonate filter membranes, followed by selective controlled chemical etching. The morphology of the nanowires and cylindrical NEEs was imaged by scanning electron microscopy. The protruding nanoelectrodes were in good parallel order. EDX study showed that the nanoelectrode elements consisted of pure gold. The electrochemical evaluation of the 3D electrodes was conducted using the well known [Fe（CN）6]^3-/[Fe（CN）6]^4- couple. Cyclic voltammgrams （CV） show a very low double layer charging current and a higher ratio of signal to background current than 2D disc NEEs. Electrochemical impedance spectroscopy （EIS） indicates that the 3D cylindrical NEEs effectively accelerate the charge transfer process, which is in consistent with the results of CV. The linear relationship with a slope of 0.5 between lg Ipc and lg v shows that linear diffusion is dominant on the 3D cylindrical NEEs at conventional scan rates.     

Lithium Ferrocyanide Catholyte for High-Energy and Low-cost Aqueous Redox Flow Batteries**

Aqueous redox flow batteries (ARFBs) are a promising technology for grid-scale energy storage, however, their commercial success relies on redox-active materials (RAM) with high electron storage capacity and cost competitiveness. Herein, a redox-active material lithium ferrocyanide (Li₄[Fe(CN)₆]) is designed. Li⁺ ions not only greatly boost the solubility of [Fe(CN)₆]⁴⁻ to 2.32 M at room temperature due to weak intermolecular interactions, but also improves the electrochemical performance of [Fe(CN)₆]^4−/3−. By coupling with Zn, ZIRFBs were built, and the capacity of the batteries was as high as 61.64 Ah L⁻¹ (pH-neutral) and 56.28 Ah L⁻¹ (alkaline) at a [Fe(CN)₆]⁴⁻ concentration of 2.30 M and 2.10 M. These represent unprecedentedly high [Fe(CN)₆]⁴⁻ concentrations and battery energy densities reported to date. Moreover, benefiting from the low cost of Li₄[Fe(CN)₆], the overall chemical cost of alkaline ZIRFB is as low as $11 per kWh, which is one-twentieth that of the state-of-the-art VFB ($211.54 per kWh). This work breaks through the limitations of traditional electrolyte composition optimization and will strongly promote the development of economical [Fe(CN)₆]^4−/3−-based RFBs in the future.     

Electrochemical Modification of Gold Electrodes with Azobenzene Derivatives by Diazonium Reduction

An electrochemical study of Au electrodes electrografted with azobenzene (AB), Fast Garnet GBC (GBC) and Fast Black K (FBK) diazonium compounds is presented. Electrochemical quartz crystal microbalance, ellipsometry and atomic force microscopy investigations reveal the formation of multilayer films. The elemental composition of the aryl layers is examined by X‐ray photoelectron spectroscopy. The electrochemical measurements reveal a quasi‐reversible voltammogram of the Fe(CN)₆^3?/4? redox couple on bare Au and a sigmoidal shape for the GBC‐ and FBK‐modified Au electrodes, thus demonstrating that electron transfer is blocked due to the surface modification. The electrografted AB layer results in strongest inhibition of the Fe(CN)₆^3?/4? response compared with other aryl layers. The same tendencies are observed for oxygen reduction; however, the blocking effect is not as strong as in the Fe(CN)₆^3?/4? redox system. The electrochemical impedance spectroscopy measurements allowed the calculation of low charge‐transfer rates to the Fe(CN)₆^3? probe for the GBC‐ and FBK‐modified Au electrodes in relation to bare Au. From these measurements it can be concluded that the FBK film is less compact or presents more pinholes than the electrografted GBC layer.     

A Biomass-Derived Carbon-Based Electrocatalyst for Efficient N2 Fixation to NH3 under Ambient Conditions

Currently, NH₃ production primarily depends on the Haber–Bosch process, which operates at elevated temperatures and pressures and leads to serious CO₂ emissions. Electrocatalytic N₂ reduction offers an environmentally benign approach for the sustainable synthesis of NH₃ under ambient conditions. This work reports the development of biomass-derived amorphous oxygen-doped carbon nanosheet (O−CN) using tannin as the precursor. As a metal-free electrocatalyst for N₂-to-NH₃ conversion, such O−CN shows high catalytic performances, achieving a large NH₃ yield of 20.15 μg h⁻¹ mg⁻¹_cat. and a high Faradic efficiency of 4.97 % at −0.6 V vs. reversible hydrogen electrode (RHE) in 0.1 m HCl at ambient conditions. Remarkably, it also exhibits high electrochemical selectivity and durability.     

Peculiarities of mass transfer and natural convection in the redox system [Fe(CN)<Subscript>6</Subscript>]<Superscript>3−</Superscript>/[Fe(CN)<Subscript>6</Subscript>]<Superscript>4−</Superscript> with current flowing through a microorifice in insulating coating on the electrode

Variations in the current in the [Fe(CN)₆]³⁻/[Fe(CN)₆]⁴⁻ system flowing through a vertical microorifice in the insulating film on the electrode are shown. Steady- and nonsteady-state conditions of electrolysis are studied for different insulating film thicknesses. The obtained results suggest that at steady-state electrolysis, in an insulator channel, near the electrode, a “stagnant zone” is formed in which the natural convection of electrolyte is weak. Mass transfer in this zone preferentially occurs due to the reagent diffusion. The length of this zone increases with the increase in the channel length. A zone with the natural convection of electrolyte is located at a certain distance from the electrode, closer to the insulator surface. A part of this zone is located in the solution bulk and its thickness is independent of the channel length. The mass transfer in this zone is realized by both the reagent diffusion and the natural convection of electrolyte. Voltammetric measurements show that at sufficiently high potential scanning rates, the peak currents on a planar electrode and on an electrode placed on the bottom of the channel in the insulating film virtually coincide. This result points to the possibility of using potentiodynamic methods for analyzing the electrolyte composition inside the channel and in the solution bulk irrespective of the thickness of the electrode-insulating film.     

Enhancement of electrochemical and catalytic properties of MoS2 through ball-milling

MoS₂ nanosheets of one to few layer thickness present novel electronic and enhanced catalytic properties with respect to the bulk material. Here we show that a simple and highly scalable ball-milling procedure can lead to significant improvements of the electrochemical and catalytic properties of the bulk natural MoS₂. We characterized the material before and after the milling process by means of scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy in order to evaluate morphological and chemical features. We investigated the electrochemical properties by means of voltammetry techniques to monitor the electron transfer with [Fe(CN)₆]^{4 −/3 −} redox probe and the catalytic properties by monitoring the electrochemical hydrogen evolution reaction (HER). A significant overpotential lowering of about 210 mV is obtained for the HER by the ball-milled material when compared to bulk materials. This has a huge potential for the lowering of the energy consumption during hydrogen evolution. Ball-milling offers highly scalable dry method for large scale production of electrocatalyst with enhanced properties.     

Vacancy Engineering of Iron-Doped W18O49 Nanoreactors for Low-Barrier Electrochemical Nitrogen Reduction

The electrochemical nitrogen reduction reaction (NRR) is a promising energy-efficient and low-emission alternative to the traditional Haber–Bosch process. Usually, the competing hydrogen evolution reaction (HER) and the reaction barrier of ambient electrochemical NRR are significant challenges, making a simultaneous high NH₃ formation rate and high Faradic efficiency (FE) difficult. To give effective NRR electrocatalysis and suppressed HER, the surface atomic structure of W₁₈O₄₉, which has exposed active W sites and weak binding for H₂, is doped with Fe. A high NH₃ formation rate of 24.7 μg h⁻¹ mg_cat⁻¹ and a high FE of 20.0 % are achieved at an overpotential of only −0.15 V versus the reversible hydrogen electrode. Ab initio calculations reveal an intercalation-type doping of Fe atoms in the tunnels of the W₁₈O₄₉ crystal structure, which increases the oxygen vacancies and exposes more W active sites, optimizes the nitrogen adsorption energy, and facilitates the electrocatalytic NRR.     

扫描电化学显微镜沉积六氰合铁酸盐微阵及其催化活性成像

采用扫描电化学显微技术在玻碳电极表面沉积出K₂Cu[Fe(CN)₆]和K₂Fe[Fe(CN)₆]微阵, 并对所得的微阵结构进行了可视化表征. 铜微电极和镀铁铂微电极阳极化产生金属离子, 然后与玻碳电极(基底电极)上还原产生的[Fe(CN)₆]^4－在微区生成六氰合铁酸盐沉淀, 操纵探针以跳跃沉积方式可以得到沉淀的点阵结构. 通过改变K₃[Fe(CN)₆]的浓度和沉积时间可以调整沉淀斑的直径和厚度. 扫描电化学显微镜成像表明微阵结构对多巴胺的氧化和过氧化氢的还原有明显的电催化作用.     

Electrodeposition at Highly Negative Potentials of an Iron-Cobalt Oxide Catalyst for Use in Electrochemical Water Splitting

Earth-abundant transition metal-based catalysts have been extensively investigated for their applicability in water electrolysers to enable overall water splitting to produce clean hydrogen and oxygen. In this study a Fe−Co based catalyst is electrodeposited in 30 seconds under vigorous hydrogen evolution conditions to produce a high surface area material that is active for both the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER). This catalyst can achieve high current densities of 600 mAcm⁻² at an applied potential of 1.6 V (vs RHE) in 1 M NaOH with a Tafel slope value of 48 mV dec⁻¹ for the OER. In addition, the HER can be facilitated at current densities as high as 400 mA cm⁻² due to the large surface area of the material. The materials were found to be predominantly amorphous but did contain crystalline regions of CoFe₂O₄ which became more evident after the OER indicating interesting compositional and structural changes that occur to the catalyst after an electrocatalytic reaction. This rapid method of creating a bimetallic oxide electrode for both the HER and OER could possibly be adopted to other bimetallic oxide systems suitable for electrochemical water splitting.