Crystallization kinetics of crosslinkable polymer complexes of novolac resin and poly(ethylene oxide)

Results of a study on the isothermal crystallization and thermal behavior of both uncured and hexamine-cured novolac/poly(ethylene oxide) (PEO) complexes are reported. The crystallization behavior of PEO in complexes is strongly influenced by factors such as composition, crystallization temperature, complexation, and crosslinking. The time dependence of the relative degree of crystallinity at high conversion deviated from the Avrami equation. The cured complexes exhibited an obvious two-stage crystallization (primary crystallization and crystal perfection), and this was more evident at higher crystallization temperature and high PEO-content. The addition of a noncrystallizable component into PEO caused a depression of both the overall crystallization rate and the melting temperature. In general, complexation and curing resulted in an increase in the overall crystallization rate. Complexation and curing are beneficial to the nucleation of PEO. Additionally, curing led to changes of the nucleation mechanism. Experimental data on the overall kinetic rate constant K_n were analyzed by means of the nucleation and crystal growth theory. For uncured complexes, the surface free energy of folding, σ_e, increased with increasing novolac content, whereas for cured complexes, σ_e displayed a maximum with the variation of composition. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2726–2736, 1999     

Crystallization,morphology, structure and miscibility of poly(ethylene oxide) based blends

Results of an investigation on the morphology, structure, isothermal crystallization, thermal behaviour and miscibility of poly(ethylene oxide) (PEO) based binary blends are reported. In particular poly(vinyl acetate)(PVAc), poly(methyl methacrylate) (PMMA) at different tacticity and poly(ethyl methacrylate) (PEMA) were added to PEO. It was found that with the only exception of isotactic poly(methyl methacrylate) (IPMMA), the addition of the above cited components causes a depression in both the spherulite growth rate and the overall kinetic rate constant. The experimental G and Kn were analyzed by means of the latest kinetic theory in order to determine the influence of composition on the process of surface secondary nucleation. The optical microscopy of thin films of the sample revealed that the blends crystallized with volume filling crystals at least up to 50/50 blend composition. The small angle X-ray scattering curves were analyzed using a recently developed methodology. The structural properties of the blends were attributed to the presence of the non crystallizable material in the interlamellar or interfibrillar regions of PEO. From the glass transition temperature it has been deduced that an homogeneous amorphous phase is present for all the blends except for the PEO/IPMMA amorphous system. For the system PEO/atactic poly(methyl methacrylate) (APMMA) the miscibility was also predicted by theoretical approaches.     

Crystallization and melting behavior of poly(ethylene oxide)/poly(n-butyl methacrylate) blends

The phase diagram, crystallization and melting behavior of poly(ethylene oxide) (PEO)/poly(n-butyl methacrylate) (PnBMA) blends have been investigated using differential scanning calorimetry and optical microscopy. The results show that the blends are miscible up to 85 °C and show an lower critical solution temperature-type demixing at a higher temperature. The isothermal crystallization studies of the blends indicate a reduction in the overall rate of crystallization. Analysis of isothermal crystallization data by means of Avrami equation leads to average values of the Avrami index of 2.5 for pure PEO and 3.0 for the different blend compositions. The melting behavior of the blends reveals double endotherms, which is ascribed to both secondary crystallization and recrystallization. The melting point depression study yielded χ₁₂=0, indicating a relatively low interaction strength.     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

A DSC study of miscibility and phase separation in crystalline polymer blends of phenolphthalein poly(ether ether sulfone) and poly(ethylene oxide)

The miscibility of blends of phenolphthalein poly(ether ether sulfone) (PES-C) and poly(ethylene oxide) (PEO) was established on the basis of the thermal analysis results. Differential scanning calorimetry (DSC) studies showed that the PES-C/PEO blends prepared by casting from N,N-dimethylformamide (DMF) possessed a single, composition-dependent glass transition temperature (T_g), and thus that PES-C and PEO are miscible in the amorphous state at all compositions at lower temperature. At higher temperature, the blends underwent phase separation, and the PES-C/PEO blend system was found to display a lower critical solution temperature (LCST) behavior. The phase separation process in the blends has also been investigated by using DSC. Annealed at high temperatures, the PES-C/PEO blends exhibited significant changes of thermal properties, such as the enthalpy of crystallization and fusion, temperatures of crystallization and melting, depending on blend composition when phase separation occurred. These changes reflect different characteristics of phase structure in the blends, and were taken as probes to determine phase boundary. From both the thermal analysis and optical microscopy, the phase diagram of the blend system was established. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1383–1392, 1997     

Effect of poly(butylene succinate) crystals on spherulitic growth of poly(ethylene oxide) in binary blends of the two substances

The effects of the lamellar growth direction, extinction rings, and spherulitic boundaries of poly(butylene succinate) (PBSU) on the spherulitic growth of poly(ethylene oxide) (PEO) were investigated in miscible blends of the two crystalline polymers. In the crystallization process from a homogeneous melt, PBSU first developed volume‐filling spherulites, and then PEO spherulites nucleated and grew inside the PBSU spherulites. The lamellar growth direction of PEO was identical with that of PBSU even when the PBSU content was about 5 wt %. PEO, which intrinsically does not exhibit banded spherulites, showed apparent extinction rings inside the banded spherulites of PBSU. The growth rate of a PEO spherulite, G_PEO, was influenced not only by the blend composition and the crystallization temperature of PEO, but also by the growth direction with respect to PBSU lamellae, the boundaries of PBSU spherulites, and the crystallization temperature of PBSU, T_PBSU. The value of G_PEO first increased with decreasing T_PBSU when a PEO spherulite grew inside a single PBSU spherulite. Then, G_PEO decreased when T_PBSU was further decreased and a PEO spherulite grew through many tiny PBSU spherulites. This behavior was discussed based on the aforementioned factors affecting G_PEO. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 539–547, 2009     

Miscibility of poly(ethylene oxide) with poly(N-vinyl pyrrolidone): DMTA and DTA studies

Dynamic mechanical thermal analysis and calorimetric studies are reported on blends of poly(ethylene oxide) (PEO) with poly(N-vinyl pyrrolidone) (PVP) between 80% and 40% PEO. DMTA curves show a peak corresponding to a phase of pure PEO and another peak which can be attributed to blended material. The calorimetric analysis shows an appreciable melting point depression and a marked decrease in the crystallization rate as the PVP content increases. The melting point depression follows the Nishi-Wang equation, giving an interaction parameter of ?0.50. These studies suggest the existence of microphases in the blend.     

Miscible blends containing a crystallizable component: poly(vinyl alcohol)/poly(ethyleneimine)

Blends of poly(vinyl alcohol) (PVAI) with poly(ethyleneimine) (PEI) were prepared by casting from a common solvent. All blends show a single, composition dependent glass transition temperature (T_g), indicating that the blends are miscible in the amorphous state and in the melt. The overall crystallization rate of PVAI in the blend decreases with increasing PEI content. The crystallinity index of PVAI in the blend does not decrease greatly with PEI content up to a composition of 70/30 PVAI/PEI, since the T_g of the crystallizable component PVAI is larger than that of the non-crystallizable component PEI. The T_g of the system PVAI/PEI decreases with increasing PEI content. The interaction parameter B of the two polymers in the melt was found to be −24 J/cm³.     

Phase behavior and crystallization of a poly(ethylene oxide)/cellulose acetate butyrate blend

The phase behavior of a partially miscible blend of poly(ethylene oxide) (PEO) and cellulose acetate butyrate (CAB) and the crystalline microstructure of PEO in the blend were studied with differential scanning calorimetry (DSC), optical microscopy, and synchrotron small‐angle X‐ray scattering (SAXS) methods. PEO/CAB showed a lower critical solution temperature (LCST) of 168 °C at the critical composition of PEO of 60 wt %. All blend compositions showed a single glass‐transition temperature (T_g) when they were prepared at temperatures lower than the LCST. However, with increasing CAB content, T_g of the blend changed abruptly at 70 wt % CAB; that is, a cusp existed. Below 70 wt % CAB, the change in T_g with blend composition was predicted by the Brau–Kovacs equation, whereas this change was predicted by the Fox equation at higher CAB contents. A gradual but small depression of the melting point of PEO in the blend with an increasing amount of CAB suggested that the PEO/CAB blends exhibited a weak intermolecular interaction. From DSC and SAXS experiments, it was found that amorphous CAB was incorporated into the interlamellar region of PEO for blends with less than 20 wt % CAB, whereas it was segregated to exist in the interfibrillar region in PEO for other blends with larger amounts of CAB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1673–1681, 2002     

Thermosetting polymer blends of unsaturated polyester resin and poly(ethylene oxide). I. Miscibility and thermal properties

The miscibility and thermal properties of polyethylene oxide(PEO)/oligoester resin (OER) blends and PEO/crosslinked polyester (PER) blends were studied by differential scanning calorimetry (DSC). The effect of quenching process on the crystallization behavior of PEO for these two systems were investigated and discussed in details. It has been found that a single, composition dependent glass transition temperature (T_g) was observed for all the blends, indicating that the two systems are miscible in the amorphous state at overall compositions. From the melting point depression of PEO, the interaction parameter χ₁₂ for PEO/OER blends and that for PEO/PER blends were found to be −1.29 and −2.01, respectively. The negative values of χ₁₂ confirmed that both PEO/OER blends and PEO/PER blends are miscible in the molten state. Quenching process has a greater hindrance on the crystallization of PEO/OER blends than on that of PEO/PER blends. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3161–3168, 1997     

Miscible blends of polylactide and poly(methyl methacrylate): Morphology,structure, and thermal behavior

The miscibility of polylactic acid (PLA) and atactic poly(methyl methacrylate) (PMMA) blends is investigated as a function of composition. The blends quenched from the melt show the presence of a single glass transition temperature dependent on the composition. The equilibrium melting temperature is determined using the Hoffman‐Weeks method and a depression is observed with increasing content of the PMMA component. The PLA spherulite growth rate and the overall isothermal crystallization rates decrease with increasing the amount of the amorphous component. The increase of the long period value as a function of the PMMA content in the blend is due to the segregation of PMMA component in the amorphous PLA interlamellar regions. The Lauritzen‐Hoffman secondary nucleation theory analysis shows that the segregation of the PMMA in the interlamellar region induces an increase in the surface entropy of folding. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1168–1177     

AFM-tip-induced crystallization of poly(ethylene oxide) melt droplets

The AFM-tip-induced crystallization of poly(ethylene oxide) (PEO) melt droplets was studied. The melt droplets with a height of 50–100 nm and a lateral size of 2–3 μm were obtained by melting the PEO ultra-thin films on a mica surface. For the PEO samples with average molecular weights (M _n) ranging from 1.0 × 10³ g/mol to 1.0 × 10⁴ g/mol, the lateral perturbation from the AFM tip in the hard-tapping or nanoscratch modes could not induce the growth of the flat-on lamellae. In contrast, under AFM nanoindentation mode, the tip-induced crystallization occurred when a sufficiently high vertical tip force was applied to the melt droplets of PEO with M _n ⩾ 1.0 × 10⁴ g/mol. Moreover, the experimental results indicated that the AFM-tip-induced crystallization of PEO in the nanoindentation process had molecular weight dependence. Translated from Acta Polymerica Sinica, 2006, (4): 553–556 (in Chinese)     

The mechanism of α-γ transition of poly- (vinylidene fluoride) in the miscible blends

The simultaneous DSC-FTIR was used for the observation of crystallization and melting of poly(vinylidene fluoride) (PVDF) and its blends with poly(methyl methacrylate) (PMMA) and poly(ethyl methacrylate) (PEMA). The isothermal crystallization was carried out under the condition of both α-form and γ-form crystallized competitively. The crystal growth rate of α -form and γ -form were evaluated from the absorbance changes at 795 cm^-1 (α -form, CH₂ rocking) and 810 cm^-1 (γ -form, CH₂ rocking) obtained by the DSC-FTIR. The crystal growth rate of γ -form decreased at the same crystallization temperature in the order of PVDF/syn-PMMA, PVDF/PEMA and PVDF/at-PMMA, which was corresponding to the order of interaction parameter. The mechanism of α -g transition of PVDF in the miscible blends with at-PMMA, syn-PMMA and PEMA was evaluated from the relationship between the decrease of α -form and the increase of γ -form. The critical crystallization temperature, at which the transformation from α -form to γ -form proceeded only in the solid state, shifted to higher temperature side in the order of interaction parameter. This revised version was published online in August 2006 with corrections to the Cover Date.     

Crystallization kinetics of poly(ethylene oxide) confined in semicrystalline poly(vinylidene) fluoride

Polymer blends based on poly(vinylidene fluoride) (PVDF) and poly(ethylene oxide) (PEO) have been prepared to analyze the crystallization kinetics of poly(ethylene oxide) confined in semicrystalline PVDF with different ratios of both polymers. Both blend components were dissolved in a common solvent, dimethyl formamide. Blend films were obtained by casting from the solution at 70 °C. Thus, PVDF crystals are formed by crystallization from the solution while PEO (which is in the liquid state during the whole process) is confined between PVDF crystallites. The kinetics of crystallization of the confined PEO phase was studied by isothermal and nonisothermal experiments. Fitting of Avrami model to the experimental DSC traces allows a quantitative comparison of the influence of the PVDF/PEO ratio in the blend on the crystallization behavior. The effect of melting and further recrystallization of the PVDF matrix on PEO confinement is also studied. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 588–597     

Miscibility,melting, and crystallization of poly(butylene‐2,6‐naphthalate)/poly(ether imide) blends

We prepared blends of poly(butylene‐2,6‐naphthalate) (PBN) and poly(ether imide) (PEI) by solution‐casting from dichloroacetic acid solutions. The miscibility, crystallization, and melting behavior of the blends were investigated with differential scanning calorimetry (DSC) and dynamic mechanical analysis. PBN was miscible with PEI over the entire range of compositions, as shown by the existence of single composition‐dependent glass‐transition temperatures. In addition, a negative polymer–polymer interaction parameter was calculated, with the Nishi–Wang equation, based on the melting depression of PBN. In nonisothermal crystallization investigations, the depression of the crystallization temperature of PBN depended on the composition of the blend and the cooling rate; the presence of PEI reduced the number of PBN segments migrating to the crystallite/melt interface. Melting, recrystallization, and remelting processes occurring during the DSC heating scan caused the occurrence of multiple melting endotherms for PBN. We explored the effects of various experimental conditions on the melting behavior of PBN/PEI blends. The extent of recrystallization of the PBN component during DSC heating scans decreased as the PEI content, the heating rate, the crystallization temperature, and the crystallization time increased. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1694–1704, 2004     

Conformational changes of poly(ethylene oxide) in poly(ethylene oxide)/poly(methyl methacrylate) blends by supercritical carbon dioxide

The effects of supercritical carbon dioxide (SC CO₂) fluids on the morphology and/or conformation of poly(ethylene oxide) (PEO) in PEO/poly(methyl methacrylate) (PMMA) blends were investigated by means of differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and Fourier transform infrared (FTIR). According to DSC data for a given blend, the melting enthalpy and, therefore, degree of crystallinity of PEO were increased, whereas the melting temperature of PEO was decreased, with SC CO₂ treatment. The enhancement of PEO crystallization with SC CO₂ treatment, as demonstrated by DSC data, was supported by WAXD data. According to FTIR quantitative analyses, before SC CO₂ treatments, the conformation of PEO was transformed from helix to trans planar zigzag via blending with PMMA. This helix‐to‐trans transformation of PEO increased proportionally with increasing PMMA content, with around 0.7% helix‐to‐trans transformation per 1% PMMA incorporation into the blend. For a given blend upon SC CO₂ treatments, the conformation of PEO was transformed from trans to helix. This trans‐to‐helix transformation of PEO decreased with increasing PMMA contents in the blends because of the presence of interactions between the two polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2479–2489, 2004     

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate)–Poly(vinyl‐acetate) blends

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate) (PHB)–poly(vinyl acetate) (PVAc) blends from the melt were investigated by differential scanning calorimetry using various cooling rates. The results show that crystallization of PHB from the melt in the PHB–PVAc blends depends greatly upon cooling rates and blend compositions. For a given composition, the crystallization process begins at higher temperatures when slower scanning rates are used. At a given cooling rate, the presence of PVAc reduces the overall PHB crystallization rate. The Avrami analysis modified by Jeziorny and a new method were used to describe the nonisothermal crystallization process of PHB–PVAc blends very well. The double‐melting phenomenon is found to be caused by crystallization during heating in DSC. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 443–450, 1999     

STUDIES OF THE CRYSTALLIZATION BEHAVIOR IN THE CRYSTALLINE/AMORPHOUS POLYMER BLENDS: POLY(ETHYLENE OXIDE)/POLY(METHYL METHACRYLATE) AND POLY(ETHYLENE OXIDE)/POLY(VINYL ACETATE)

The crystallization process of poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA)and PEO/poly(vinyl acetate) (PVAc) blends has been characterized by Fourier Transform Infrared(FTIR) spectra in conjunction with Differential Scanning Calorimeter (DSC) measurements. Thecrystallinity of PEO varies consistently with PEO content in PEO/PVAc blends and the PEO/PMMAblends containing 50 wt% or less PMMA. For the PEO/PMMA blends containing 60 wt% ormore PMMA, the crystallinity of PEO decreases more than PEO content but develops with crystal-lization time. These results can be explained in terms of difference between the crystallization tem-perature (T_c) and glass transition temperature (T_g) of the blends as a function of content of amorphouscomponent.     

Thermal characterization of polycarbonate/polycaprolactone blends

In this work, we prepared blends of bisphenol A polycarbonate (PC) and poly(ϵ‐caprolactone) (PCL) in a wide composition range by melt mixing and solution mixing. Two different molecular weights of PCL were used (nominally, 10.000 g/mol, PCL10, and 80.000 g/mol, PCL80). The thermal behavior of both systems was studied via differential scanning calorimetry under dynamic and isothermal conditions. The blends were miscible in the entire composition range in the liquid and amorphous states, as indicated by the single glass‐transition temperature (T_g) exhibited by both the PC/PCL10 and PC/PCL80 blends. The compositional variation of the T_g was accurately described by the Fox equation for the PC/PCL80 blends, whereas slight deviations from this equation were exhibited by the PC/PCL10 blends. For blend compositions containing 40% or more PCL, either one or both blend components crystallized. Crystallization occurred during cooling from the melt or during subsequent heating in the form of cold crystallization. Although PCL crystallization was reduced and its crystallization rate decreased with the addition of PC, PCL was a very effective macromolecular plasticizer for PC, to the extent that crystallization during the scan was detected for some blend compositions. Isothermal crystallization experiments allowed the determination of equilibrium melting points (T) by the Hoffman–Weeks extrapolation method. A T depression was found for both PCL and PC components as the content of the other blend component was increased. The Avrami equation was closely obeyed by both blend components during the isothermal overall crystallization kinetics up to crystalline conversion degrees of 60–70% and with values of Avrami indices ranging from 3 to 4, depending on the crystallization temperature employed. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 771–785, 2001     

Characterization of poly(carboxylic acid)/poly(ethylene oxide) blends formed through hydrogen bonding by spectroscopic and calorimetric analyses

The solid state of the complex between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO), and that between poly(methacrylic acid) (PMAA) and PEO formed via hydrogen-bonding was studied by differential-scanning calorimetric (DSC) and by Fourier-transform infrared (FT–IR) spectroscopic measurements. Melting temperature T_m and the degree of the crystallinity X_c of PEO in the systems PAA (or PMAA)/PEO blends obtained from aqueous or dimethyl sulfoxide (DMSO) medium were measured in various unit mol % of PEO ([PEO]100/{[PAA(or PMAA)] + [PEO]}) where [ ] is the unit mole concentration. It was found that 50 unit mol % of PEO is a critical composition, which gives new evidence for the 1 : 1 complex formation between PAA (or PMAA) and PEO. From the FT–IR spectroscopic analysis in conjunction with DSC measurements we also found that the effects of solvent and of hydrophobic interaction (due to the α-methyl group of PMAA) are the important factors controlling the complexation in the solution and solid systems. These factors also affect the crystallization behavior and the microstructure of the PAA (or PMAA)/PEO blend in solid state.