Interaction between model poly(ethylene terephthalate) thin films and weakly ionised oxygen plasma

Model films of poly(ethylene terephthalate) were treated by oxygen plasma in order to quantify the etching rate and estimate the contribution of charged and neutral particles to the reaction probability. Model films with a thickness of 50 nm were deposited on a quartz crystal of a microbalance (QCM) by spin‐coating technique. The samples were exposed to oxygen plasma with the positive ion density of 4 × 10¹⁵ m^?3 and neutral oxygen atom density of 6 × 10²¹ m^?3. The etching rate was determined from the QCM signal and was 4.7 nm s^?1. The etching was found rather inhomogeneous as the atomic force microscopic images showed an increase of the surface roughness as a result of plasma treatment. The model films were completely removed from the surface of the quartz crystals in about 12 s. Knowing the etching rate and the flux of oxygen atoms to the surface allowed for calculation of the reaction probability which was found to be rather low at the value of 1.6 × 10^?4. Copyright © 2011 John Wiley & Sons, Ltd.     

Electronic conductivity of pyrrole and aniline thin films polymerized by plasma

In this article, we present a study of the influence of temperature and humidity on the electric conductivity of polyaniline and polypyrrole thin films doped with iodine and synthesized by plasma (PAn/I and PPy/I, respectively). The polymers presented the characteristic ohmic conduction mechanism via electrons; however, the conductivity was much lower than that presented by the polymers obtained by traditional chemical oxidation. We submitted the polymers to heating–cooling cycles to study the temperature dependence of the conductivity. During the heating stage of the cycles, the electric conductivity of PPy/I showed a strong dependence on the humidity content. However, during the cooling step, the plots of conductivity, as a function of the inverse temperature of PPy/I and PAn/I, showed typical Arrhenius behavior. The activation energy of PPy/I had an average value of 1.1 ± 0.1 eV and was independent of the reaction time, whereas PAn/I presented a more complex behavior with activation energies that depended on the reaction time and the regional crystallinity induced in the heating step of the cycles. All the activation energies were below 2 eV, which places them in the semiconductor regime. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3247–3255, 2000     

Preparation and characterization of plasma-polymerized styrene thin films

Plasma-polymerized styrene (PPS) thin films (several hundred to several thousand Å thick) have been prepared under a variety of discharge conditions in a tubular reactor inductively coupled to a radio frequency (13.56 MHz) power supply. Studies have focussed on the correlation of deposited polymer structure, evidenced both at the film surface (via XPS analysis) and in the bulk polymer (via transmission FT–IR analysis) with controllable plasma parameters (coupled rf power, monomer flow rate, monomer pressure). It has been determined that the relative number of phenyl rings incorporated into the film intact is an inverse function of the power per styrene molecule ratio. Polymer deposition rate was found to be a strong function of styrene flow rate and substrate temperature. Plausible elements of the styrene plasma polymerization mechanism will be considered.     

Characterization of vapor deposition polymerized polyimide thin films

Vapor deposition polymerized (VDP) polyimide (PI) thin films were prepared and characterized by using thermogravimetrical analysis (TGA), scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared (FTIR), and bending-beam techniques. The film properties investigated were thermal stability, wet-etching characteristics, surface topology, imidization characteristics, internal stress upon curing and thermal cycling, and hygroscopic stress upon moisture diffusion. Markedly different characteristics are observed for the VDP-PI films when comparing with the conventional ones. They seem denser in film structure and have better mechanical properties, but are somewhat less stable in thermal resistance. © 1996 John Wiley & Sons, Inc.     

Preparation and characterization of mesoporous silica thin films from polyethoxysiloxanes

Tetraethoxysilane (TEOS) and polyethoxysiloxanes (PEOSs; prepared by the acid‐catalyzed hydrolytic polycondensation of TEOS) were subjected to the sol–gel process in the presence of cetyltrimethylammonium bromide (CTAB), respectively. The PEOSs with M_w 700–26,000, as prepared by sol–gel coating of TEOS and PEOS under various conditions, were used. Uniform and crack‐free thin films of thickness 276–613 nm were prepared by spin‐coating of a PEOS solution containing CTAB. When the coating films were sintered at 400 °C, the combustion of ethoxy groups and CTAB took place to provide porous silica thin films. The structure of the thin films was found to be dependent on the molecular weight of PEOS and the molar ratio of CTAB/Si: lamellar or hexagonal phase was observed for M_w less than 15,000 and for CTAB/Si molar ratios greater than 0.10. Honeycomb structures were observed for M_w less than 5000 and for CTAB/Si molar ratios of 0.15. The honeycomb structure was also observed by atomic force microscopy and transmission electron microscope. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2542–2550, 2006     

Preparation and characterization of anthracenecarboxylic acid doped polyaniline thin films

Doped polyaniline films were prepared with electrochemistry method. A small conjugated molecule, anthracenecarboxylic acid(2-ACA), was used as the dopant, considering its electrical activeness due to the conjugated π-π* structure. Film morphology of doped and undoped polyaniline samples was investigated. The corresponding changes in optical and electrical properties after ACA doping were discussed. By measuring and calculating their energy level distribution, a promising application of polyaniline thin films as buffer layer in optic-electric devices is expectable.     

Preparation and characterization of thin films of monomeric and polymeric octacyanophthalocyanines

Thin films were prepared on substrates, cleavage surface of KCl single crystal, and metallic copper, by reaction of 1,2,4,5-tetracyanobenzene with the substrate at various temperatures. The films were characterized by elemental analysis, IR, and UV/VIS spectroscopies. The films were observed by scanning electron microscopy. The films produced on copper at temperatures between 300 and 400°C consisted of copper octacyanophthalocyanine and its polymer with ladder structure. The ratio of polymer to monomer increased with elevating the reaction temperature. The films were composed of ribbon-like crystals. The film produced on copper above 450°C was composed of an amorphous and continuous layer of polymeric copper phthalocyanine. The film produced on KCl at temperatures between 250 and 350°C consisted of potassium octacyanophthalocyanine and its polymer with ladder structure. The film produced on KCl above 450°C was polymeric potassium phthalocyanine. Those films contained more metal content than that required stoichiometrical.     

DC conduction mechanism in plasma polymerized vinylene carbonate thin films prepared by glow discharge technique

Electrical glow discharge technique was employed for the preparation of plasma polymerized vinylene carbonate (PPVC) thin films of aluminum/thin film/aluminum sandwich structure at room temperature by a parallel plate capacitively coupled reactor. The structural investigation of the monomer VC and PPVC was performed by Fourier transform infrared spectroscopy. The current density-voltage characteristics follow a power law of the form J α V ⁿ , where n has different values. In the low voltage region 0.85 < n < 1.00 and those in the high voltage region lie between 1.30 < n < 1.75, indicating Ohmic current conduction in the low voltage region and non-Ohmic conduction in the high voltage region. In addition, at higher temperature the current density increased significantly revealing a temperature dependence of the current density. Theoretically calculated values and experimental results of Schottky and Poole-Frenkel coefficients show that the most probable conduction mechanism in the PPVC thin films is of Schottky type.     

Radiofrequency-discharge plasma treatment of heavy ion-irradiated poly(ethylene terephthalate) films

The effects of treatment in a radiofrequency (RF) discharge plasma on the rate of chemical etching of the tracks made by xenon ions (with an energy of ~1 MeV/nucleon) in poly(ethylene terephthalate) (PETP) films were investigated. The influence of plasma treatment conditions on the structure and properties of nuclear track membranes formed by etching was studied. It was found that the RF plasma treatment of heavy ion-bombarded PETP films leads to a decrease in etchability of both tracks and the starting polymer matrix. The changes in track and matrix etchability due to crosslinking of the polymer surface layer were shown to be responsible for the asymmetry of the track membrane structure.     

Preparation and characterization of iron(II) complexes of ethylene glycol

Nine iron(II) ethylene glycol sulphate complexes were prepared. Their compositions were determined by standard analytical methods. They were characterized by means of temperature-dependent magnetic susceptibility and Mössbauer spectroscopic measurements. On the basis of the patterns of their thermal decompositions, the complexes could be classified into three groups.

---

Zusammenfassung Neun Eisen(II)-ethylenglykol-sulfat-Komplexe wurden dargestellt. Die Zusammensetzung dieser Komplexe wurde nach analytischen Standardmethoden bestimmt. Die Verbindungen wurden durch Messungen der temperaturabhängigen magnetischen Susceptibilität sowie mittels Mössbauer-Spektroskopie charakterisiert. Nach dem Verhalten bei der thermischen Zersetzung konnten diese Komplexe in drei Gruppen klassifiziert werden.

---

, . . , .

     

Protein adhesion on silicon-supported hyperbranched poly(ethylene glycol) and poly(allylamine) thin films

Hyperbranching poly(allylamine) (PAAm) and poly(ethylene glycol) (PEG) on silicon and its effect on protein adhesion was investigated. Hyperbranching involves sequential grafting of polymers on a surface with one of the components having multiple reactive sites. In this research, PAAm provided multiple amines for grafting PEG diacrylate. Current methodologies for generating PEG surfaces include PEG-silane monolayers or polymerized PEG networks. Hyperbranching combines the nanoscale thickness of monolayers with the surface coverage afforded by polymerization. A multistep approach was used to generate the silicon-supported hyperbranched polymers. The silicon wafer surface was initially modified with a vinyl silane followed by oxidation of the terminal vinyl group to present an acid function. Carbodiimide activation of the surface carboxyl group allowed for coupling to PAAm amines to form the first polymer layer. The polymers were hyperbranched by grafting alternating PEG and PAAm layers to the surface using Michael addition chemistry. The alternating polymers were grafted up to six total layers. The substrates remained hydrophilic after each modification. Static contact angles for PAAm (32-44 degrees) and PEG (33-37 degrees) were characteristic of the corresponding individual polymer (30-50 degrees for allylamine, 34-42 degrees for PEG). Roughness values varied from approximately 1 to 8 nm, but had no apparent affect on protein adhesion. Modifications terminating with a PEG layer reduced bovine serum albumin adhesion to the surface by approximately 80% as determined by ELISA and radiolabel binding studies. The hyperbranched PAAm and PEG surfaces described in this paper are nanometer-scale, multilayer films capable of reducing protein adhesion.     

Preparation and preliminary characterization of poly(ethylene glycol)-pepstatin conjugate

The carboxyl function of pepstatin has been coupled, through an amide bond, to methoxypoly(ethylene glycol) (5 kDa), to which an amino function had been previously grafted. The mPEG-pepstatin conjugate inhibits hog pepsin (aspartic proteinase) in vitro as pepstatin itself, however, with a 400 times higher apparent K_i. The conjugate apparently does not inhibit proteinases belonging to other proteinase families such as serine (trypsin, carboxypeptidase Y), cysteine (Papaya proteinase III), or metallo (collagenase) proteinases.     

Preparation and characterization of thin films of SiO(x) on gold substrates for surface plasmon resonance studies

We report here on the fabrication and characterization of stable thin films of amorphous silica (SiO(x)) deposited on glass slides coated with a 5 nm adhesion layer of titanium and 50 nm of gold, using the plasma-enhanced chemical vapor deposition (PECVD) technique. The resulting surfaces were characterized using atomic force microscopy (AFM), ellipsometry, contact angle measurements, and surface plasmon resonance (SPR). AFM analysis indicates that homogeneous films of silica with low roughness were formed on the gold surface. The deposited silica films showed excellent stability in different solvents and in piranha solution. There was no significant variation in the thickness or in the SPR signal after these harsh treatments. The Au/SiO(x) interfaces were investigated for their potential applications as new surface plasmon resonance sensor chips. Silica films with thicknesses up to 40 nm allowed visualization of the surface plasmon effect, while thicker films resulted in the loss of the SPR characteristics. SPR allowed further the determination of the silica thickness and was compared to ellipsometric results. Chemical treatment of the SiO(x) film with piranha solution led to the generation of silanol surface groups that have been coupled with a trichlorosilane.     

In vacuo photocurrent measurements of plasma polymerized styrene films

Photoconductivity measurements were carried out on plasma polymerized styrene (PPS) in vacuo, in air, and in subsequently re-evacuated conditions. Samples with two gold electrodes (Au-PPS-Au) and gold-aluminum electrodes (Au-PPS-Al) were used. Positive short circuit photocurrents in the direction of illumination were observed in both types of specimens. In the case of Au-PPS-Au, photocurrent threshold was about 1.6 eV in vacuo for the virgin film, which is attributed to the energy of hole generation in bulk. Residual free radicals were assumed to be the acceptors in this mechanism. In the case of Au-PPS-Al, electron injection from aluminum was thought to be a more likely mechanism, with an estimated barrier height of approximately 2.6 eV.     

Interactions of oxygen and ethylene with submonolayer Ag films supported on Ni(111)

We investigate the oxidation of, and the reaction of ethylene with, Ni(111) with and without sub-monolayer Ag adlayers as a function of temperature. The addition of Ag to Ni(111) is shown to enhance the activity towards the ethylene epoxidation reaction, and increase the temperature at which ethylene oxide is stable on the surface. We present a systematic study of the formation of chemisorbed oxygen on the Ag-Ni(111) surfaces and correlate the presence and absence of O(1-) and O(2-) surface species with the reactivity towards ethylene. By characterizing the samples with low-energy electron microscopy (LEEM) in combination with X-ray photoelectron spectroscopy (XPS), we have identified specific growth of silver on step-edge sites and successfully increased the temperature at which the produced ethylene oxide remains stable, a trait which is desirable for catalysis.     

Fabrication and anti-fouling properties of photochemically and thermally immobilized poly(ethylene oxide) and low molecular weight poly(ethylene glycol) thin films

Poly(ethylene oxide) (PEO) and low molecular weight poly(ethylene glycol) (PEG) were covalently immobilized on silicon wafers and gold films by way of the CH insertion reaction of perfluorophenyl azides (PFPAs) by either photolysis or thermolysis. The immobilization does not require chemical derivatization of PEO or PEG, and polymers of different molecular weights were successfully attached to the substrate to give uniform films. Microarrays were also generated by printing polymer solutions on PFPA-functionalized wafer or Au slides followed by light activation. For low molecular weight PEG, the immobilization was highly dependent on the quality of the film deposited on the substrate. While the spin-coated and printed PEG showed poor immobilization efficiency, thermal treatment of the PEG melt on PFPA-functionalized surfaces resulted in excellent film quality, giving, for example, a grafting density of 9.2×10(-4)?(-2) and an average distance between grafted chains of 33? for PEG 20,000. The anti-fouling property of the films was evaluated by fluorescence microscopy and surface plasmon resonance imaging (SPRi). Low protein adsorption was observed on thermally-immobilized PEG whereas the photoimmobilized PEG showed increased protein adsorption. In addition, protein arrays were created using polystyrene (PS) and PEG based on the differential protein adsorption of the two polymers.     

Preparation and characterization of nanostructured Ni(OH)2 and NiO thin films by a simple solution growth process

Nanostructured Ni(OH)2 thin films were prepared by a simple solution growth process with F(-) and NH3 used as Ni2+ coordination agents, and ammonia hydroxide solution used as OH(-) supplier to accelerate the hydrolyzation of nickel complex species. The results showed Ni(OH)2 thin films were constructed mainly with hexagonal beta-Ni(OH)2 nanorods; the F(-) and NH3 in reactive solutions played important roles in the film growth process; and solution pH had great influence on the morphologies of thin films, which was explained by the competition of Ni(OH)2 nucleation and growth in solutions. NiO crystallinity thin films were obtained by annealing Ni(OH)2 thin films at 400 degrees C for 2 h and the morphologies of the Ni(OH)2 thin films were sustained well during the annealed process.     

Preparation and characterization of nanoaggregates of poly(ethylene oxide)-b-polymethacrylate and poly-L-lysine

Poly(ethylene oxide)-b-polymethacrylate (PEO-b-PMA), one of the double-hydrophilic block copolymers, has proved to the form nanoaggregates with poly-L-lysine (PLS). This was confirmed by turbidimetry, zeta-potential measurements, and dynamic light scattering. The nanoaggregate formation is induced by electrostatic charge neutralization of the PMA block with PLS. The properties of the aggregates are affected by PLS concentration as well PEO-b-PMA concentration. The aggregates have potential applications in biomedical science.