XPS analysis of the poly(ethylene terephthalate) film grafted with acrylamide

Graft polymerization of acrylamide (AAm) was performed onto the surface of a poly(ethylene terephthalate) (PET) film with the simultaneous UV irradiation method but using no photosensitizer and without degassing. To examine whether polyacrylamide (PAAm) was introduced into the bulk place of PET film by the surface graft polymerization, an x-ray photoelectron spectroscopic (XPS) study was performed on the PAAm-grafted PET films. The distribution of grafted PAAm chains on and in the PET films was estimated from the PAAm/PET ratio calculated from the XPS spectra of PET films with different amounts of grafted PAAm. The results clearly demonstrate that graft polymerization has actually occurred not merely on the outermost surface but also within the thin surface region of the PET film. In addition, the XPS analysis revealed that the PET component was always present in the grafted surface region by a mole fraction of 0.1 to 0.05 even when the amount of PAAm grafted was larger than 10 μg/cm².     

Surface modification of polyethylene fiber by graft polymerization

To improve the wettability and adhesion, graft polymerization of acrylamide (AAm) and glycidyl methacrylate (GMA) was performed onto the surface of ultra-high modulus polyethylene (UHMPE) fiber pretreated with Ar plasma. Following the plasma treatment and the subsequent exposure to air to introduce peroxides onto the fiber surface, graft polymerization onto the UHMPE fiber was allowed to proceed from the polymer peroxides either in deaerated monomer solution at an elevated temperature (degassing method), or in aerated monomer solution containing riboflavin at 30°C under UV irradiation (photoinduction method). The monomer solution was prepared from water and dioxane for AAm and GMA, respectively. After rigorous removal of homopolymers, surface analysis of the grafted fibers was performed with ATR-FTIR and XPS, which revealed that PAAm and PGMA chains were grafted in the surface region of fibers. The grafting rate of PAAm by the photoinduction method was much higher than that by the degassing method when compared at the same concentration of the AAm solution. The amount of PGMA grafted was greatly affected by UV irradiation time, but depended on plasma treatment time to an insignificant extent if the treatment was carried out for longer than 30 s. Reaction of propylamine with the PGMA-grafted surface resulted in the appearance of a nitrogen peak in the XPS spectrum, suggesting the presence of epoxy groups on the surface of PGMA grafted fiber. © 1994 John Wiley & Sons, Inc.     

Oxidation of polyethylene surface by corona discharge and the subsequent graft polymerization

Oxidation of a polyethylene (PE) surface by corona discharge and the subsequent graft polymerization of acrylamide (AAm) were studied. The maximum amount of peroxides introduced by corona treatment at a voltage of 15 kV was about 2.3 × 10^?9 mol cm^?2. The decomposition rate of peroxide and the dependence of graft amount on the storage period of the corona-treated PE films showed that there were several kinds of peroxides, the labile one being mainly responsible for the initiation of graft polymerization. When the corona-treated film was brought into contact with a deaerated aqueous solution of AAm, graft polymerization took place more strongly with the treatment time, but was reduced after passing a maximum. Although the x-ray photoelectron spectroscopic analyses of the corona-treated PE films showed homogeneous oxidation of the outer polymer surface by corona discharge, optical microscopy on the cross section of the grafted film revealed the graft polymerization to be limited to a very thin surface region.     

Photoinduced graft polymerization of acrylic acid on the surface of polypropylene films from a thin layer of nondeaerated aqueous solution of the monomer

Photoinduced graft polymerization of acrylic acid on the polypropylene film surface containing a preliminarily adsorbed photoinitiator (benzophenone) from a thin layer of a nondeaerated aqueous solution of the monomer, isolated from the contact with atmospheric oxygen, was studied. Data were obtained on how the amount of the grafted polymer and the wetting angle for water on the film surface depends on the duration of the UV irradiation and on the monomer solution layer thickness. These data are compared with the results previously obtained for the photoinduced grafting of polyacrylic acid on polyethylene films.     

UV-induced Self-initiated Graft Polymerization of Acrylamide onto Poly(ether ether ketone)

Photo-grafting of hydrophilic monomer was used to enhance the hydrophilicity of poly(ether ether ketone) (PEEK) with the aim of extending its applications to biological fields. PEEK sheets were surface modified by grafting of acrylamide(AAm) with ultraviolet(UV) irradiation in the presence or absence of benzophenone(BP). The effects of BP, irradiation time and monomer concentration on the surface wettability of PEEK were investigated. Characterization of modified PEEK using scanning electron microscopy(SEM), energy-disperse spectrometer(EDS) and water contact angle measurements shows that AAm was successfully grafted on PEEK surface both in presence and absence of BP. With the increase in irradiation time and monomer concentration, contact angles decrease to as low as 30°, demonstrating a significant improvement of surface hydrophilicity. In agreement with the decrease in contact angle, under identical conditions, the nitrogen concentration increases, suggesting the increase in grafting degree of the grafting polymerization. This investigation demonstrates a self-initiation of PEEK due to its BP-like structure in the backbone of the polymer. Though the graft polymerization proceeds more readily in the presence of BP, the self-initiated graft polymerization is clearly observed.     

PHOTO-INDUCED GRAFT POLYMERIZATION OF ACRYLAMIDE ON POLYPROPYLENE MEMBRANE SURFACE IN THE PRESENCE OF DIBENZYL TRITHIOCARBONATE

Ultraviolet （UV）-induced graft polymerization of acrylamide （AAm） on polypropylene substrates was successfully conducted using dibenzyl trithiocarbonate （DBTTC） as photoinitiator. It was confirmed by chemical analysis and surface morphology observation with attenuated total reflectance Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy. A possible mechanism for this graft process was presented, which suggested that, under UV irradiation, the C： S bond in DBTTC could split and abstract a hydrogen from the polypropylene surface and a surface free radical was then formed, and initiated the graft polymerization of AAm.     

二步法聚丙烯/丙烯酸表面接枝聚合研究

研究了二步法聚丙烯膜表面的丙烯酸接枝反应 .实验发现 ,以醋酐为溶剂的反应体系所得接枝率明显好于以水为溶剂的体系 ;接枝率随光敏剂浓度、单体浓度增大而增加 ;提高反应温度 ,可使接枝率明显增大 ;接枝后的聚丙烯膜表面亲水性可明显改善 .并用红外光谱证实了丙烯酸在聚丙烯膜表面的接枝 .     

Surface‐confined photopolymerization of single‐ and mixed‐monomer systems to tailor the wettability of poly(L‐lactide) film

The major objective of this research was to modify the surface characteristics of poly(L ‐lactide) (PLA) by grafting a combination of hydrophilic polymers to produce a continuum of hydrophilicity. The PLA film was solvent cast, and the film surfaces were activated by ultra violet (UV) irradiation. A single monomer or combination of two monomers, selected from vinyl acetate (VAc), acrylic acid (AA), and acrylamide (AAm), were then grafted to the PLA film surface using a UV induced photopolymerization process. The film surfaces resulting from each reaction step were analyzed using ATR‐FTIR spectroscopy and contact angle goniometry. Results showed that AAm dominated the hydrophilicity of the film surface when copolymerized with VAc or AA, while the water contact angles for PLA films grafted with poly(vinyl acetate‐co‐acrylic acid) varied more gradually with feed composition. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6534‐6543, 2006     

接枝丙烯酰胺改善聚乙烯膜表面亲水性的研究

利用等离子体技术和紫外照射接枝相结合在聚乙烯膜表面接枝丙烯酰胺(AAm)以改善其亲水性。通过衰减全反射红外光谱(ATR-FTIR)、X射线光电子能谱(XPS)和接触角测定验证了在无光引发剂的条件下,将等离子体预处理和紫外照射接枝结合起来可以有效地提高AAm的接枝效果,很好地改善PE膜表面的亲水性。探讨了等离子体复合参数W/(FM)、等离子体预处理时间、AAm单体浓度以及紫外照射时间对改善PE膜表面亲水性的影响,确定改善PE膜表面亲水性的最佳实验条件。     

PEGDA/HEMA水凝胶等离子体表面改性的研究

采用紫外光聚合法合成了聚乙二醇双丙烯酸酯(PEGDA)/甲基丙烯酸-2-羟基乙酯(HEMA)复合凝胶,在不同的条件下进行等离子处理后,紫外光下进行表面接枝改性。在凝胶表面引入亲水性基团,改善材料的亲水性。研究了不同等离子体处理条件及辐射条件对丙烯酰胺(AAm)接枝率的影响。研究表明,丙烯酰胺接枝率随着等离子体处理时间的增加先增大后减小,随着紫外光照射时间、丙烯酰胺浓度的增大而增大。     

Graft copolymerization of methacrylic acid and acrylamide onto acrylonitrile-butadiene-styrene terpolymer by photoinduced hydroperoxide

Graft copolymerization of methacrylic acid (MAA) or acrylamide (AM) from an aqueous solution onto acrylonitrile-butadiene-styrene terpolymer (ABS) was initiated by the thermal decomposition of polymeric hydroperoxides, which are formed upon UV irradiationof ABS, which contains anthracene. Diffusion of anthracene at room temperature from a methanolic solution into ABS was affected by the acrylonitrile content ofABS.The graft yield was independent on the concentration of anthracene in the wide range of 0.03 X 10^-3 to 14.29 X 10^?3 mol/L in ABS. The graft polymerization reaction does not occur below 100°C.The effect of other variables, such as time of irradiation, intensity of UV, reaction time, and concentration of monomer in aqueous solution, on the amount of monomer grafted to ABS were also investigated.The contact angle significantly decreases upon grafting, indicating that the graft layer is on the surface of the polymer. © 1995 John Wiley & Sons, Inc.     

PET表面接枝偶氮聚合物和光致取向研究

合成了一种丙烯酸酯类含芳香族偶氮生色团的单体ANB .以二苯甲酮为引发剂 ,采用固相紫外光接枝方法将上述单体接枝到聚酯 (PET)膜的表面 ,得到了一种具有光响应性的接枝膜 .通过SEM研究了接枝膜的表面和断面的形貌 ,观察到偶氮接枝层均匀地覆盖了PET表面 ,接枝层厚度约 0 4μm .研究发现 ,当使用488nm的线偏振激光照射接枝膜时 ,偶氮生色团通过快速的顺反异构化反应在垂直于偏振光极化方向上发生取向 ,得到了具有光学各向异性表面的PET接枝膜 .接枝膜的取向是一个快速过程 ,取向有序度参数在 2min时即达到最大值 ,为 0 0 6左右     

A facile approach to surface graft vinyl acetate onto polyolefin articles

A facile and environment friendly approach was developed to graft vinyl acetate (VAc) onto plastic articles in an aqueous solution using tert‐butyl alcohol (TBA) as a compatiblizer and benzoyl peroxide (BPO) as an initiator. In a novel setup, excessive monomer suspended in a water phase, VAc could be conveniently grafted on the model substrate of low‐density polyethylene (LDPE) film and the graft percentage (GP) could be developed up to 7.3%. Reaction temperature could increase GP significantly, while adding monomer over a critical volume did not influence GP. By adding some paradioxybenzene, i.e. 0.06–0.08% in VAc phase, homopolymer PVAc could be avoided practically, while graft polymerization proceeded favorably in aqueous solutions. It was proved by attenuated total reflection‐infrared (ATR‐IR) spectroscopy that grafted VAc was located mainly at the surface of the LDPE film and hydrophilic nature of both grafted and alcoholyzed films were improved via contact angle measurements. Copyright © 2004 John Wiley & Sons, Ltd.     

Radiation-induced graft polymerization of acrylamide I. Preparation conditions and gel determination for polyethylene-grafted films

Radiation-induced graft polymerization of acrylamide (AAm) onto low-density polyethylene(LDPE) film has been investigated. The appropriate reaction conditions at which the graft polymerization was carried out successfully were selected. It was observed that the grafting process was enhanced remarkably by using distilled water as diluent. In this grafting system ammonium ferrous sulphate (Mohr's salt) was used as inhibitor to minimize the homopolymerization of AAm and the suitable concentration of such inhibitor was found to be 3 wt %. The dependence of the grafting rate on the monomer concentration was calculated to be 2.9 order, regardless of the irradiation atmosphere (N₂ gas or under vacuum). When the radiation grafting process was carried out under vacuum, higher degrees of grafting were obtained as compared to those in nitrogen gas or in air atmosphere. Network structure was formed in the graft copolymer and the gel formation was determined in the p-xylene-extracted grafted films. Results showed good evidence that the grafting process takes place by the front mechanism.     

Melt-photografting polymerization of maleic anhydride onto LDPE film

Maleic anhydride (MAH) was photografted onto low density polyethylene substrates at temperatures above the melting point of MAH. The effects of some principal factors including irradiation temperature, photoinitiators, the intensity of UV radiation, and the far UV radiation on the grafting polymerization were investigated in detail. Percent conversion and grafting efficiency of the polymerizations were determined by the gravimetric method. The contact angles of the grafted film PE-g-PMAH against water and the FTIR spectrum of the grafted film were measured as characterization. The results show that the photografting polymerization of MAH can proceed smoothly at temperatures higher than the melting point of MAH; the far UV radiation and the intensity of the UV radiation affect the grafting polymerization greatly; the photoinitiators also have influence on the polymerization. According to the FTIR spectra, it is clearly confirmed that the grafted film samples contain anhydride groups. The contact angles demonstrate that the wettability of the grafted films is enhanced obviously, especially to those grafted film samples through hydrolysis.     

Surface structures of fluoropolymer,polyolefin and polyester films after modification by graft polymerization

Pristine and argon plasma pretreated polytetrafluoroethylene (PTFE), polystyrene (PS), high-density polyethylene (HDPE) and poly(ethylene terrephthalate) (PET) films have been subjected to near-UV light-induced graft polymerization with water-soluble acrylamide (AAm), the sodium salt of styrene sulfonic acid (NaSS), acrylic acid (AAc) and N,N-dimethylaminoethylmethylacrylate (DMAEMA) monomers. The structure and composition at the substrate surface with grafted polymer were studied by angle-resolved X-ray photoelectron spectroscopy (XPS). In most cases, the density of surface grafting is enhanced by plasma pretreatment. For each polymer substrate with a substantial amount of grafting, the hydrophilic graft penetrates or becomes partially submerged beneath a thin surface layer of dense substrate chains. This stratified microstructure is consistent with the static secondary ion mass spectroscopy (SIMS) and Ar⁺ beam depth profiling results. The two latter techniques also suggest that when the grafted polymer has a bulky substituent, there is less efficient penetration of the grafted polymer below the surface.     

Synthesis and Characterization of Carboxymethyl Cellulose-graft-Poly(Acrylamide-co-Crotonic Acid) Hydrogel: Matrix for Ammonium Nitrate Release,as Agrochemical

Russian Journal of Applied Chemistry - In this work, acrylamide (AAm) and crotonic acid (CA) were grafted onto carboxymethyl cellulose (CMC) by free-radical polymerization in aqueous solution at...     

Thermo- and pH-responsive polypropylene microporous membrane prepared by the photoinduced RAFT-mediated graft copolymerization

Thermo- and pH-responsive polypropylene microporous membrane prepared by photoinduced reversible addition–fragmentation chain transfer (RAFT) graft copolymerization of acrylic acid and N-isopropyl acrylamide by using dibenzyltrithiocarbonate as a RAFT agent. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR), X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FE-SEM) were used to characterize the structural and morphological changes on the membrane surface. Results of ATR/FT-IR and XPS clearly indicated that poly(acrylic acid) (PAAc) and poly(N-isopropyl acrylamide) (PNIPAAm) were successfully grafted onto the membrane surface. The grafting chain length of PAAc on the membrane surface increased with the increase of UV irradiation time, and decreased with the increase of the concentration of chain transfer agent. The PAAc grafted membranes containing macro-chain transfer agents, or the living membrane surfaces were further functionalized via surface-initiated block copolymerization with N-isopropyl acrylamide in the presence of free radical initiator, 2,2′-azobisisobutyronitrile. It was found that PNIPAAm can be grafted onto the PAAc grafted membrane surface. The results demonstrated that polymerization of AAc and NIPAAm by the RAFT method could be accomplished under UV irradiation and the process possessing the living character. The PPMMs with PAAc and PNIPAAm grafting chains exhibited both pH- and temperature-dependent permeability to aqueous media.     

芴酮引发光接枝改性LDPE膜的研究

采用紫外光引发接枝表面改性的方法,以芴酮(FL)为引发剂,在低密度聚乙烯(LDPE)薄膜表面上接枝丙烯酸(AA)、甲基丙烯酸(MAA)、丙烯酸甲酯(MA)、甲基丙烯酸甲酯(MMA)、丙烯酰胺(AM)等单体,以赋予薄膜表面新的化学性质.考察了引发剂浓度、紫外光的辐照时间、辐照强度、单体种类对LDPE薄膜接枝程度的影响.结果表明,在一定范围内,增加芴酮浓度,可以提高单体的接枝率,但当芴酮浓度达到5%时,接枝率反而下降.延长辐照时间至4 min和提高紫外光的辐照强度达100 W/m2,均有利于接枝反应的进行.不同单体在LDPE膜上的接枝能力与单体的活性、单体与基材的相容性等因素有关.接枝后,LDPE与水的接触角下降程度不仅与单体在膜上的接枝量有关,还与接枝单体的亲水性能密切相关.     

Surface treatment of PET fiber by EB-irradiation-induced graft polymerization and its effect on adhesion in natural rubber matrix

Aiming to develop a high performance fiber-reinforced natural rubber (NR) without using resorcinol formaldehyde latex (RFL) adhesives of environmental load substances, a special technique using electron beam (EB) irradiation-induced graft polymerization was applied to high-modulus polyethylene terephthalate (PET) fibers. Although PET is chemically inert, acrylate functional silane could be graft-polymerized onto the PET fiber surface by this special technique. The composite of NR and grafted PET fibers indicated a linear increase in the initial modulus with the fiber content. The fiber reinforced rubber with a good performance was obtained in the system of NR and grafted PET fibers.