The solvent venting injection technique in capillary supercritical fluid chromatography

A solvent venting technique for injection of volumes up to 1 μl on 50 μm i.d. SFC columns has been compared to direct injection methods. The peak broadening and peak splitting observed with direct injection have been examined and found to be related to the starting pressure, the column temperature, and the sample solvent, in addition to the sample volume. The solvent venting technique removed peak splitting and improved the column efficiency. With a proper selection of experimental conditions, the sample recovery was 100%. The major part of the solvent was eluted in 15–20 s. Several applications have been demonstrated.     

Injection of large volumes of aqueous solutions in capillary supercritical fluid chromatography and sample preconcentration by multiple injections

The possibility of using water or aqueous solutions as the solvent in capillary supercritical fluid chromatography was successfully demonstrated. Large volumes (up to 1 μl) of aqueous sample solutions were injected. Sample preconcentration was performed by means of multiple injections of aqueous sample solutions. The solutes were trapped at the beginning of the column at low density (high temperature and low pressure) and eluted using a density programme. The method can be applied to trace analysis. It proved to be linear in the range examined. Flame ionization detection was used for the studies. As this technique is not sensitive to water, no solvent peak appears, which may be an advantage for certain applications. The influence of water injections on the column performance and the reproducibility of injection was investigated.     

Detection limits of thermal conductivity and photoionization detectors in high speed narrow bore CGC

Not only the required input band width and the availability of compatible instrumentation limit the reduction of column diameter but so do the column sample capacity and detector characteristics, such as volume and sensitivity. In this paper the scope and limitations of thermal conductivity and photoionization detection at atmospheric and reduced pressures for capillary gas chromatography are discussed at length. It is shown that the sensitivity of a thermal conductivity detector is inversely proportional to the pressure. Reduction of cell volume and decrease of pressure appear equivalent with respect to minimum detectable amount and peak broadening. This results in femtogram detection limits for column diameters as low as 10 μm. For photoionization detectors the sensitivity did not improve at reduced pressures, so that the effect of reduced pressure and addition of make-up gas on the detection limits is the same. Nevertheless, the applicability of a low volume photoionization detector (40 μl) for capillary columns with a diameter as low as 50 μm will be demonstrated by series coupled PID and FID detectors and illustrated with various applications.     

Comparison of field‐enhanced and pressure‐assisted field‐enhanced sample injection techniques for the analysis of water‐soluble vitamins using CZE

A new online concentration method, namely pressure‐assisted field‐enhanced sample injection (PA‐FESI), was developed and compared with FESI for the analysis of water‐soluble vitamins by CZE with UV detection. In PA‐FESI, negative voltage and positive pressure were simultaneously applied to initialize PA‐FESI. PA‐FESI uses the hydrodynamic flow generated by the positive pressure to counterbalance the reverse EOF in the capillary column during electrokinetic sample injection, which allowed a longer injection time than usual FESI mode without compromising the separation efficiency. Using the PA‐FESI method, the LODs of the vitamins were at ng/mL level based on the S/N of 3 and the RSDs of migration time and peak area for each vitamin (1 μg/mL) were less than 5.1%. The developed method was applied to the analysis of water‐soluble vitamins in corns.     

An automated large volume on-column injection technique for capillary gas chromatography

Automated large volume (25-200 μl) on-column injections into a gas chromatograph with a capillary column were successfully performed by coupling a retention gap technique with an air actuated rotary valve. The linearity, injection precision, and carryover were evaluated. Slight boiling point discrimination was observed. This technique is compatible with commonly used chromatographic detectors (FID, ECD, MS) and conditions, while requiring very little instrument modification. The work is directed at the eventual reduction of manpower and turnaround time for sample collection and extraction, and Kuderna-Danish concentration when dealing with methods similar to EPA 625.     

Improved peak capacity for CE separations of enzyme inhibitors with activity‐based detection using magnetic bead microreactors

A technique for separating and detecting enzyme inhibitors was developed using CE with an enzyme microreactor. The on‐column enzyme microreactor was constructed using NdFeB magnet(s) to immobilize alkaline phosphatase‐coated superparamagnetic beads (2.8 μm diameter) inside a capillary before the detection window. Enzyme inhibition assays were performed by injecting a plug of inhibitor into a capillary filled with the substrate, AttoPhos. Product generated in the enzyme microreactor was detected by LIF. Inhibitor zones electrophoresed through the capillary, passed through the enzyme microreactor, and were observed as negative peaks due to decreased product formation. The goal of this study was to improve peak capacities for inhibitor separations relative to previous studies, which combined continuous engagement electrophoretically mediated microanalysis and transient engagement electrophoretically mediated microanalysis to study enzyme inhibition. The effects of electric field strength, bead injection time and inhibitor concentrations on peak capacity and peak width were investigated. Peak capacities were increased to ≥20 under optimal conditions of electric field strength and bead injection time for inhibition assays with arsenate and theophylline. Five reversible inhibitors of alkaline phosphatase (theophylline, vanadate, arsenate, L ‐tryptophan and tungstate) were separated and detected to demonstrate the ability of this technique to analyze complex inhibitor mixtures.     

Analytical characteristics of combined gas chromatographic systems: Packed precolumn-open tubular column

The peculiarities of the flow splitting technique for sample injection into a capillary column have been discussed. A comparative investigation of reproducibility of the analytical results obtained for two gas chromatographic systems using flow splitting [1) sample injector-packed predolumn-splitter-open tubular capillary column and (2) sample injector-splitter-open tubular capillary column] has been carried out. It was experimentally shown that the first system ensures considerably better reproducibility for the results concerning the composition of the analyzed mixtures. Other advantages of the first system are also discussed.     

An Insight into Peak‐Splitting Phenomenon in On‐Column Concentration‐Micellar Electrokinetic Capillary Chromatography for Aqueous Sample Solution

Abstract

A detailed study was carried out to investigate the origin of the peak‐splitting phenomena in on‐column concentration‐micellar electrokinetic capillary chromatography for aqueous sample solution. The system studied was a basic phosphate and borax mixed buffer with sodium dodecyl sulfate (SDS) as micellar phase. Phenol, benzyl alcohol, phenyl ethanol, salicylic acid, and p‐hydroxy benzyl acid were selected as the analytes. Several factors that affect peak splitting were investigated. The injection time, SDS micellar concentration, hydrophobicity of the analytes, and analytes concentration were the most important factors. A hypothesis was proposed to explain the peak‐splitting phenomena. Several means to avoid peak‐splitting phenomena were proposed, such as controlling sample injection time and hydrophobicity of the analyte, decreasing SDS concentration and increasing sample concentration. However, the most practical method for avoiding peak splitting was to control the sample injection time.     

Development and evaluation of a GC/FID method for the analysis of free amino acids in quince fruit and jam.

A GC/FID methodology for determination of twenty-one free amino acids in quince fruit (pulp and peel) and jam is described. The sample preparation was simple, involving a SCX Solid-Phase Extraction (SPE) purification step and a fast derivatization with ethyl chloroformate for gas chromatographic analysis. The chromatographic separation was achieved using a CP-Sil 19 CB wcot fused-silica capillary column. Under the chosen conditions, with temperature and pressure programming, this capillary column was able to separate all the amino acids not only in a short time but also with good separation. The GC/FID procedure is rapid, sensitive, reproducible and accurate. The detection limit values for amino acids were low, between 0.004 and 0.115 microg/mL, and the method was precise. As a general rule, the recovery values were high. Due to its rapidity and low cost, this technique can be useful in the quality control of quince products.     

Improving splitless injection with electronic pressure programming

An experimental injection port has been designed for split or splitless sample introduction in capillary gas chromatography; the inlet uses electronic pressure control, in order that the column head pressure may be set from the GC keyboard, and the inlet may be used in the constant flow or constant pressure modes. Alternatively, the column head pressure may be programmed up or down during a GC run in a manner analogous to even temperature programming. Using electronic pressure control, a method was developed which used high column head pressures (high column flow rates) at the time of injection, followed by rapid reduction of the pressure to that required for optimum GC separation. In this way, high flow rates could be used at the time of splitless injection to reduce sample discrimination, while lower flow rates could be used for the separation. Using this method, up to 5 μl of a test sample could be injected in the splitless mode with no discrimination; in another experiment, 2.3 times as much sample was introduced into the column by using electronic pressure programming. Some GC peak broadening was observed in the first experiment.     

Improving sensitivity by large-volume sample stacking combined with sweeping without polarity switching by capillary electrophoresis coupled to photodiode array ultraviolet detection

An easy, simple, and highly efficient on-line preconcentration method for polyphenolic compounds in CE was developed. It combined two on-line concentration techniques, large-volume sample stacking (LVSS) and sweeping. The analytes preconcentration technique was carried out by pressure injection of large-volume sample followed by the EOF as a pump pushing the bulk of low-conductivity sample matrix out of the outlet of the capillary without the electrode polarity switching technique using five polyphenols as the model analytes. Identification and quantification of the analytes were performed by photodiode array UV (PDA) detection. The optimal BGE used for separation and preconcentration was a solution composed of 10 mM borate-90 mM sodium cholate (SC)-40% v/v ethylene glycol, without pH adjustment, the applied voltage was 27.5 kV. Under optimal preconcentration conditions (sample injection 99 s at 0.5 psi), the enhancement in the detection sensitivities of the peak height and peak area of the analytes using the on-line concentration technique was in the range of 18-26- and 23-44-fold comparing with the conventional injection mode (3 s). The detection limits for (-)-epigallocatechin (EGC), (-)-epicatechin (EC), (+)-catechin (C), (-)-epigallocatechin gallate (EGCG), and (-)-epicatechin gallate (ECG) were 4.3, 2.4, 2.2, 2.0, and 1.6 ng/mL, respectively. The five analytes were baseline-separated under the optimum conditions and the experimental results showed that preconcentration was well achieved.     

Determination of flotation reagents used in tin-mining by capillary electrophoresis.

Alkyl xanthates (O-alkyl dithiocarbonates) and phosphonates are important organic collectors for the flotation of metals from crude ore. Leaching from waste dumps into river and ground water, these substances can cause environmental pollution. A capillary electrophoretic method for the routine determination of ethyl, isopropyl, hexyl xanthate, and styrene phosphonate has been developed. Separation within 12 min could be achieved in borate pH 8.8 performing UV detection at 254 and 300 nm simultaneously. To improve the limits of detection obtained with hydrodynamic injection (0.4-1.5 ppm), field amplified sample injection (FASI) and stacking were investigated. An increase in sensitivity up to 4-8 fold could be achieved by pressure assisted FASI. Applying a stacking method to enrich the analytes by filling the capillary with sample solution to one third of its length, the limits of detection could be decreased to 10-40 ppb. Water samples from a former tin ore mining area have been analyzed using the optimized stacking technique. Quantitation was performed by standard addition. Good precision and accuracy were obtained, making this robust capillary electrophoretic method well-suited for routine analysis.     

Large-volume sample stacking for on-capillary sample enrichment in the determination of naphthalene- and benzenesulfonates in real water samples by capillary zone electrophoresis

We investigated the on-line preconcentration of a test mixture of 15 substituted and unsubstituted naphthalene(NSs) and benzenesulfonates (BZSs) by large-volume sample stacking (LVSS). Analyses were carried out by capillary zone electrophoresis (CZE) with on-column UV detection. In particular, we focused on how experimental variables such as the inside diameter of the capillary, the volume of sample introduced and polarity switching influenced the enrichment procedure. The best results were obtained when 300 nl were injected and stacked using a bubble cell capillary. Under these conditions, LVSS increased the detector response of conventional hydrodynamic injection by a factor of 40. The limits of detection of the method were between 5 and 10 microg l(-1). Determinations were reproducible, in terms of peak area and migration time, under such conditions. The performance of the method was examined by determining NS and BZS in real samples, such as tap, river and surface waters and inflow/outflow waters from a water treatment plant. Real samples were injected directly into the CZE column with little or no preparation.     

pH-mediated acid stacking with reverse pressure for the analysis of cationic pharmaceuticals in capillary electrophoresis

When using capillary electrophoresis (CE) for the analysis of biological samples, it is often necessary to employ techniques to overcome peak-broadening that results from having a high-conductivity sample matrix. To improve the concentration detection limits and separation efficiency of cationic pharmaceuticals in CE, pH-mediated acid stacking was performed to electrofocus the sample, improving separation sensitivity for the analyzed cations by 60-fold. However, this method introduces a large titrated acid plug into the capillary. To overcome the limitations this low-conductivity plug poses to stacking, the plug was removed prior to the separation step by applying reverse pressure to force it out of the anode of the capillary. Employing this technique allows for roughly twice the volume of sample to be injected. A maximum sample injection time of 240 s was attainable with baseline peak resolution compared to a maximum sample injection time of 120 s without reverse pressure, leading to a twofold decrease in the limits of detection of the analytes used. Separation efficiency overall is also improved when utilizing the reverse pressure step. For example, a 60 s sample injection time results in 94,000 theoretical plates as compared to 60,500 theoretical plates without reverse pressure. This reverse-pressure method was used for detection and quantitation of several cationic pharmaceuticals that were prepared in Ringer's solution to simulate microdialysis sampling conditions.     

A simple and rapid pre-confirmation method to distinguish endogenous human haemoglobin from synthetic haemoglobin-based oxygen carriers in doping control

A specific, sensitive and rapid analytical procedure based on capillary electrophoresis with UV/Vis detection at 405 and 415?nm was developed and validated to detect human haemoglobin and haemoglobin-based oxygen carriers (Hemopure?, Oxyglobin? and Polyheme?) in blood samples collected for doping control. The electrophoretic separation, based on capillary dynamic coating, was achieved in less than 10 min. The effects of capillary temperature, injection conditions and initial ramping were investigated. The optimum separation voltage was 25 kV with a capillary temperature of 20 °C, initial ramping of 1?kV/s and an injection pressure of 0.5?psi for 10?s. The removal of haptoglobin using anti-human haptoglobin antibody prior to the analysis was mandatory to increase the specificity of the analysis. Sufficient resolution between endogenous haemoglobin variants and the three haemoglobin-based oxygen carriers here investigated was obtained, thus allowing discrimination between a normal haemolysed sample and a sample in which Oxyglobin?, Hemopure? or Polyheme? is present. Good repeatability of migration times (CV% less than 1), peak resolution and adequate sensitivity (limit of detection: 2.5?mg/mL) was obtained.     

On the minimization of the band-broadening contributions of a modern, very high pressure liquid chromatograph

The contributions of the volume of sample injected, the mobile phase flow rate, the inner diameter of the needle seat capillary and that of the connector capillary, the heat exchanger, and the detector cell volume to the widths of bands eluted from the 1290 Infinity HPLC instrument were investigated in depth. Four sample volumes (0.16, 0.80, 4.0, and 20 μL), three flow rates (0.04, 0.4, and 4.0 mL/min), two needle seat capillary I.D. (100 mm × 115 and 140 μm), three sets of connector capillary I.D. (350 mm × 80, 115, and 140 μm placed upstream the column, and 220 mm × 80, 115, and 140 μm downstream the column), two UV detector cell volumes (0.8 and 2.4 μL), and the presence/absence of the heat exchanger (1.6 μL) between the inlet connector capillary tube and the column were combined to generate up to 4 × 3 × 2 × 3 × 2 × 2=288 system configurations for this instrument. For each configuration, 5 consecutive injections were performed in order to assess the injection-to-injection repeatability, providing 1440 elution band profiles which are analyzed. The results demonstrate that the band broadening contribution of the instrument depends mostly on the detector cell volume and on the inner diameter of the needle seat capillary tube. The impact of these two contributions is particularly important at high flow rates (4 mL/min). Best efficiencies are obtained with a small sample volume, below 1 μL, which avoids volume overload of the instrument, or with large sample volumes, which maximize the radial concentration gradients of the sample across the instrument channels, in the vicinity of the anfractuosities of the channel walls. The injection of large sample volumes reveals the imperfection of current injection systems, the performance of which is remote from the one expected to provide an ideal rectangular injection (～+4 μL(2)). Although the present behavior of the instrument is satisfactory, serious improvements would become necessary to operate the next generation of more efficient columns that might be commercialized soon.     

毛细管区带电泳峰形变化规律的研究

采用指数修正的高斯模型（ＥＭＧ）,研究了进样时间、分离电压及柱长等一系列操作条件对毛细管区带电泳峰形参数的影响。实验结果表明,进样时间对半峰宽（Ｗ１／２）和峰不对称度（Ｂ／Ａ）有显著影响;电压对以长度表示的半峰宽及峰拖尾参数无显著影响;ｔｍ与σ、τ、Ｗ１／２（ｓ）之间都有很好的线性关系;随着柱长的增大,σ、τ、Ｗ１／２都略有增加。     

Use of disposable open tubular ion exchange pre-columns for in-line clean-up of serum and plasma samples prior to capillary electrophoretic analysis of inorganic cations

A simple analytical system using disposable, open-tubular ion exchange clean-up precolumns coupled in-line to capillary electrophoresis for direct injection of biological samples is presented. The clean-up precolumns were prepared from fused silica capillaries by thermally initiated layer-by-layer polymerization of poly(butadiene-maleic acid) (PBMA) directly on the capillary wall. Typically, 6 cm long precolumns with 4-layers of PBMA were used for sample pretreatment. A robust and reproducible coupling between the precolumn (75 μm ID) and the analytical capillary (50 μm ID) was achieved using an inexpensive, commercially available low dead volume union. No extra dispersion of the analyte zones was observed. Proteins and other high molecular weight compounds from biological sample matrices were retained on the cation-exchanger sites of the precolumn, which eliminated their adsorption on analytical capillary walls and ensured stable electroosmotic flow and migration times of target analytes. Unretained small inorganic cations migrated freely into the analytical capillary for separation and detection. Applicability of the sample clean-up procedure was proved by determination of major inorganic cations in blood serum and plasma samples using capillary electrophoresis with contactless conductivity detection. Separations were performed in background electrolyte solution consisting of 15 mM L-arginine, 12.5 mM maleic acid, 3 mM 18-crown-6 at pH 5.5 and repeatabilities of migration times and peak areas were below 1.5% and 7.3%, respectively. Less than 1 μL of biological sample was required for injection.     

顶空毛细管气相色谱法测定吡虫啉中的丁酮

采用顶空毛细管气相色谱法测定吡虫啉中的丁酮残留量。样品经二氯甲烷溶解,用HP–5毛细管色谱柱分离,氢火焰离子化检测器检测,顶空平衡温度为70℃,平衡时间为10 min,以外标法计算含量。丁酮的质量浓度在2.0~510.0μg/m L范围内线性关系良好,相关系数r=0.999 7,方法的检出限为0.5μg/m L,样品3个水平的加标回收率为99.4%~102.1%,测定结果的相对标准偏差小于3.0%(n=5)。该方法简便快速,准确可靠,可用于吡虫啉产品的质量控制。     

Simple 2D-HPLC using a monolithic silica column for peptide separation

Separation of peptides by fast and simple two-dimensional (2D)-HPLC was studied using a monolithic silica column as a second-dimension (2nd-D) column. Every fraction from the first column, 5 cm long (2.1 mm ID) packed with polymer-based cation exchange beads, was subjected to separation in the 2nd-D using an octadecylsilylated (C18) monolithic sillica column (4.6 mm ID, 2.5 cm). A capillary-type monolithic silica C18column (0.1 mm ID, 10 cm) was also employed as a 2nd-D column with split flow/injection. Effluentof the first dimension (1st-D) was directly loaded into an injector loop of 2nd-D HPLC. UV and MS detection were successfully carried out at high linear velocity of mobile phase at 2nd-D using flow splitting for the 4.6 mm ID 2nd-D column, or with directconnection of the capillary column to the MS interface. Two-minute fractionation inthe 1st-D, 118-second loading, and 2-second injection by the 2nd-D injector, allowed one minute for gradient separation in the 2nd-D, resulting in a maximum peak capacity of about 700 within 40 min. The use of a capillary column in solvent consumption and better MS detectability compared to a larger-sized column. This kind of fast and simple 2D-HPLC utilizing monolithic silica columns will be useful for the separation of complex mixtures in a short time.