Hydrothermal synthesis of cobalt carbonates using different counter ions: An efficient precursor to nano-sized cobalt oxide (Co3O4)

Synthesis of submicrometer crystalline particles of cobalt carbonate was achieved hydrothermally using different cobalt salts and urea with a molar ratio from 1:3 to 1:20 (cobalt salt:urea) in aqueous solutions at 160 °C for 24-36 h, in the presence of cetyltrimethylammonium bromide (CTAB) as a surfactant. Nanoparticles of Co₃O₄, with an average size from 30 to 39 nm, were obtained by thermal decomposition of CoCO₃ samples at 500 °C for 3 h in an electrical furnace. The as-synthesized products were characterized by powder X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), UV-Vis spectra and thermal analysis. Studying the optical properties of the as-prepared cobalt oxide nanoparticles showed the presence of two band gaps, the values of which confirmed the semiconducting properties of the prepared Co₃O₄.     

Preparation of muscovite with ultrahigh specific surface area by chemical cleavage

The specific surface area of a muscovite sample increases drastically after exposure to a LiNO₃ solution, e.g., from 3.4 m²/g, corresponding to platelets of ca. 200 silicate layers, to 295 m²/g (platelets of ca. 2–3 silicate layers) after treatment at 180°C under atmospheric pressure for 46 h. The efficiency of the cleavage process decreases with decreasing temperature (down to 50°C). The LiNO₃/H₂O weight ratio is also very important: at 130°C and a reaction time of 46 h, for instance, a value in the range of 1.7–1.8 leads to the highest specific surfaces. The cleaved products have the form of strong papers that disperse readily in water. During the cleaving procedure, not only the particle thickness, but also the diameter decreases. There is no evidence of damage or partial dissolution of the silicate structure after cleavage, by IR spectroscopy and yield. The use of LiCl also leads to an increase in specific surface area, but the effect is weaker than in the case of LiNO₃. Treatment with some other alkaline and alkaline earth nitrates and chlorides did not increase the specific surface area of muscovite significantly.     

Preparation and properties of uniform colloidal metal phosphates IV. Cadmium-, nickel-, and manganese(II)-phosphates

Colloidal dispersions of uniform spherical particles of cadmium phosphate, nickel basic phosphate, and manganese (II) phosphate were prepared by aging at elevated temperatures metal salt solutions and phosphoric acid or sodium dihydrogen phosphate in the presence of urea and sodium dodecyl sulfate. Uniform spheres were obtained only if urea and the surfactant were added within a given range of concentrations.The spherical particles were amorphous as prepared. Cadmium phosphate and nickel basic phosphate particles crystallized when calcined at appropriate temperatures. Manganese (II) phosphate particles underwent a phase transformation to crystalline plate-like solids when aged in doubly distilled water at room temperature.Supported by NFS grant CHE-8619509.Part of M. S. Thesis by L.L.S.     

Electrical properties of poly(bis(β-phenoxyethoxy)phosphazene) and its complexes

Electrical and dielectrical properties of poly(bis(-phenoxyethoxy)phosphazene) (I) and its complexes with various content ratios of AgSO₃CF₃ to monomeric unit (0.25/1 (II) and 0.5/1 (III) in molar ratio) were investigated.Dc conductivity of respective samples at 18 °C were 6.1×10^–12, 4.4×10^–9, and 7.1×10^–8 S/m.Dc conduction was considered to be due to ion hopping. Charge mobility ranged from 3×10^–12 to 6× 10^–11 m²/Vs depending on the applied field in sample II. In sample I, a tan peak was found which can be ascribed to molecular relaxation of main chains. The peak vanished upon introducing AgSO₃ CF₃. Temperature dependence of total conductivity ( _T ) measured byac method in the temperature range between –150 °C and 50 °C showed several peaks at the temperatures corresponding to the peak temperatures of tan. Total conductivities of respective samples at 100 kHz were 4.9×10^–7 (69 °C), 1.7×10^–4 (45 °C), and 1.5×10^–4(40°C)S/m.     

Micelle structure in isotropic aqueous colloids of a poly(oxyethylene) amphiphile C12E8

Micelle structure in aqueous colloids in the isotropic liquid phase (L₁) of a nonionic amphipile (n-dodecyl octa(oxyethylene glycol) monoether (C₁₂E₈) has been investigated as a function of concentration and temperature using light scattering (LS), viscometry, NMR, and small-angle X-ray scattering (SAXS).The spherical micelles, having a radius of 28–31 Å, remain in a wide concentration range from very dilute to ca. 42 wt %. The micelle size increases sligthly with increasing temperature in the range of 25–60 °C. In the concentrated colloids, the spherical micelles are likely to be arranged in a certain ordered structure. Even at such a high concentration as 30 wt %, the isotropic colloid shows Newtonian flow. This suggests that interaction between micelles in the ordered structure is very weak and the structure is very fragile. Moreover, coexistence of the isotropic phase and the ordered structure in L₁ phase is discussed.     

Formation of uniform silver particles from bis (1,2-ethanediamine)silver(I) complex

Uniform spherical silver particles were produced by decomposing the bis(1,2-ethanediamine)silver(I) complex, by aging a solution of 1.0×10^–3 mole dm^–3 in silver (I) nitrate, 1.0 mole dm^–3 in 1,2-ethanediamine, and 2.5×10^–1 mole dm^–3 in nitric acid (basic solution) at 100°C for 42 min. The average modal diameter was estimated to be 0.52 m with a relative standard deviation of 0.10. A moderately oxygenrich layer, 40 Å thick, on the surface of the particles was detected by means of photoelectron surface microanalysis (XPS). The silver particles grew through a polynuclear-layer mechanism, as judged from the concentration change in soluble silver(I) species in the supernatant solution. The particles' point of zero charge (PZC) was estimated at pH 6.5 by potentiometric titration.     

Synthesis of alkali-metal cobalt kambaldaite by precipitation method

Alkali-metal cobalt kambaldaite (alkali-metal cobalt carbonate hydroxide hydrate; ideal structure, M₂Co₈(CO₃)₆(OH)₆ · 6H₂O; M-CoKBL) was prepared by the addition of a cobalt nitrate solution into a solution containing a large excess of alkali-metal bicarbonate followed by aging at 50 °C for 2–3 h. Hydrated alkali-metal ions are present in the channels of the kambaldaite structure; therefore, we tried to ion-exchange the K-CoKBL sample with various metals. However, collapse of the kambaldaite structure took place easily because of low pH of the ion-exchange solution. The catalytic activity of Co₃O₄ obtained by the calcination of “ion-exchanged” K-CoKBL was dependent on the residual potassium content in the catalyst.     

Association of poly-(L-lysine) homologues in sodium carbonate solution

The molecular weights of isopoly(L-Iysine), poly(L-ornithine), and poly(L-, -diaminobutylic acid), the homologues of poly (L-lysine), were determined by the sedimentation equilibrium method in aqueous solutions of 1.0 M NaCl or 0.1 M Na₂CO₃. In every sample the molecular weights in the presence of carbonate ions was twice that in NaCl solution. In a previous paper we reported that poly(L-lysine) behaved as a dimer at concentrations higher than 0.4 g/dl in the presence of carbonate ions and as a monomer in dilute solution, and these two forms were related by a monomer-dimer equilibrium. The homologues did not have a monomer-dimer equilibrium relationship under the conditions of the measurements that we carried out. The CD spectrum of isopoly(L-lysine) in water showed a uniform increase with a decrease in the wave length in the presence of carbonate ions. However, in the alkaline region in NaOH solution, the spectrum changed and a small minimum at 212 nm was found. When additional carbonate ions were added a large minimum at 205 nm was observed. This result can be explained by a change in the conformation from a random coil to a regular structure. We could not compare isopoly(L-lysine) with other polypeptides, because it does not have peptide bonds. The CD spectra of poly(L-ornithine) and poly(L-, -diaminobutylic acid) in NaOH or Na₂CO₃ solutions showed only slightly regular structures. It was also confirmed that the dimer-structures of the poly (L-lysine) homologues do not have regular structures.This paper was presented at the VI. Symposium on Analytical Ultracentrifugation, Marburg, FRG, February 16–17,1989.     

Spreading and compression of n-hexadecyl acrylate at liquid-air interface

Usingn-hexadecyl acrylate, surface pressure-area (F-A) curves and equilibrium spreading pressuresF ^e were measured at various temperatures (5.7°–46°C) by the Langmuir balance (F-A) and the Wilhelmy-plate method (F ^e). At low temperatures (T<13 °C) condensed films and the liquid-condensed/solid condensed transition can be observed. At high temperatures (T>30 °C) liquid-expanded films occur. In the intermediate range the compression curves have two transition points. The transition pressureF ₁ between liquid-expanded and condensed film has a marked temperature dependence. The transition enthalpiesH ₁ decrease with increasing temperature and become zero at 29.2 °C. The second transition is related to a transition between the condensed films (F ₂). The slight temperature dependence of this transition is accompanied by an increasing change of area as well as by increasing transition enthalpiesH ₂.TheF ^e-T curve has two distinct breaks, at the melting pointT _m and atT=30 °C. The break atT _m is due to the melting process and the break atT=30 °C is caused by a phase transition between a liquid-expanded film and a condensed film.The phase diagram was constructed from the transition pressures. It can be demonstrated that the highest pressures of the thermodynamic stable film occurs atT _m. At temperaturesT>T _m equilibrium spreading pressure and equilibrium collapse pressure are identical whereas atT _m supercompression of the monolayer occurs. The film in this state behaves like a supercooled liquid. Obviously, rupture and collapse of such a film lead to a thermodynamically metastable bulk phase.     

Thermally stimulated currents in poly(bis(p-fluorophenoxy)phosphazene)

Thermally stimulated currents (TSC) were examined for poly(bis(p-fluorophenoxy)phosphazene) (PBFPP) film. TSC showed peaks at the glass transition temperature (Tg=–4 °C) and atT(1) (160 °C – 170 °C), where-form crystal phase transformed to mesophase of-form structure. Another peak was found atT _cc betweenTg andT(1). Linear relationship between polarization field and peak current ofT _cc -peak was found, which shows thatT _cc -peak was caused by motion of dipolar groups in crystalline phase. When heating (up to 200 °C) and cooling (down to 20 °C) thermal process was repeated,T _cc -peak shifted to higher temperature region approachingT(1) and simultaneously, the peak current ofT(1)-peak became smaller. Activation energy, time constant of dipolar relaxation and charge mobility were evaluated forT _cc -peak. From these results, it was concluded that-form and more ordered- form crystalline phases coexisted in PBFPP once heated aboveT(1) and the content of- form phase increased by repeated thermal hysteresis.     

The effect of carrier solution on the particle size distribution of inorganic colloids measured by steric field-flow fractionation

The number average and the weight average particle diameters for suspended inorganic colloids found by the new technique of steric field-flow fractionation may be successfully used provided that the most suitable carrier solution is selected, in order to minimize the coagulation and adhesion phenomena.In the present work polydisperse, irregular colloidal particles of FePO₄·2H₂O (strengite) were studied. The average particle diameters were found to vary with the electrolyte concentration in the suspending medium. A strong variation of the number and weight average particle diameters was also observed with the quantity of the surfactant added to aquatic medium in order to increase colloidal stability. The influence of the electrokinetic charge of the FePO₄·2H₂O particles in relation to the surface charge of the material of the column employed, on the particle size measured was investigated. The proper carrier solution for minimizing coagulation and adhesion phenomena in the FePO₄·2H₂O colloidal particles was found to contain either 1.5% (v/v) detergent FL-70 and 0.1 MKNO₃ or 0.5% (v/v) detergent FL-70 and 0.033 MNa₂SO₄.     

A small-angle neutron scattering study on polydisperse silica spheres coated with polyisobutene

Neutron-scattering studies at small angles are performed on dilute dispersions of small, polydisperse silica spheres coated with polyisobutene in mixtures of h₁₂ and d₁₂-cyclohexane. The contrast variation method is applied to reveal the internal structure of the compound particles. For a detailed interpretation of the scattering curves, it is assumed that the particles consist of spherical silica cores with concentric PIB-layers into which solvent molecules can penetrate. Also the polydispersity of the particle cores is taken into account. Model calculations fit the experimental curves fairly well except for the curves near the matching point, and at higher wavevectors, where experimental errors are relatively large due to the smallness of the scattering of the particles compared to that of the background.     

Study on the hydrothermal reaction of FeCl<Subscript>3</Subscript> solution in the presence of poly(vinyl alcohol)

A 0.5 dm³ aqueous solution of 0.1 M FeCl₃ dissolving 1 wt% poly(vinyl alcohol) (PVA) was treated hydrothermally in a stainless steel autoclave at various temperatures (T _h=110–200 °C). Highly ordered red corpuscle-like hematite particles around 2 m in diameter were produced after aging the solution at T _h=110 °C for 7 days, though large numbers of spherical PVA microgels around 2–4 m in diameter were produced together with the red corpuscle-like particles at T _h120 °C. The number of red corpuscle-like hematite particles decreased but that of spherical PVA microgels increased with increasing T _h, leading to the proposal that the method carried out in the present study will become a new synthetic method of polymer microgels. The ferric ions acted as a cross-linking agent to make PVA insoluble in water. The red corpuscle-like hematite particles produced at T _h=110 °C had high specific surface areas and showed high mesoporosity. The mesoporosity appeared to be more pronounced after evacuating the particles above 300 °C. The diameter of the mesopores after evacuation above 300 °C ranged from 2 to 20 nm, with a maximum at around 5–6 nm. The H₂O and N₂ adsorption experiments revealed that there are no ultramicropores in the particles. The H₂O and CCl₄ adsorption experiments further disclosed that the surface hydrophobicity of the particles is low even though PVA molecules remain after evacuation of the particles at 100–400 °C. Furthermore, the micropores produced after evacuation of the particles at 400 °C exhibited a high size restriction effect, i.e., the micropores produced were accessible to H₂O (diameter 0.253 nm) and N₂ (diameter 0.318 nm) molecules but not to CCl₄ (diameter 0.514 nm).     

Enthalpy of solution of phenoxyalcohols solubilized in aqueous sodium dodecylsulfate and hexadecyltrimethylammonium bromide solutions

The enthalpy of solution of phenoxy 2-ethanol, 1 phenoxy,-3 propanol and benzylalcohol was determined at 25 °C in aqueous sodium dodecylsulfate and hexadecyltrimethylammonium bromide solution, up to 0.2 mol/kg surfactant concentration. Using the pseudo-phase model, the standard enthalpy of transfer and the partition coefficient of the alcohols between micelle and water are calculated. The latter quantity is found to be systematically larger when derived from enthalpy than from free energy measurements. Using the so-called compensation plot, the solution thermodynamics of aromatic and aliphatic alcohols in aqueous sodium dodecylsulfate and in the octane+water systems are compared. Aromatic alcohols display an anomalous behavior in the octane+ water system but not in the micellar one.The standard enthalpy of solution of various alcohols presents, when plotted against hexadecyltrimethylammonium bromide concentration, a shoulder in the region around 0.05 mol/kg; a discussion is presented on the evidence for alleged micellar structural changes in aqueous micellar systems.     

Hemolytic activity of polyoxyethylene cholesteryl ethers

Hemolytic activity of nonionic surfactants, polyoxyethylene cholesteryl ethers, C₂₇H₄₅O(CH₂CH₂O) _n H (Chol-E _n ,n=, 25, 30, 50) and polyoxyethylene dihydrocholeseryl ethers, C₂₇H₄₇O(CH₂CH₂O) _n H (DHChol-E _n ,n=15, 30 50) were measured, changing the concentration of surfactant and erythrocyte at 37 °C. Maximum hemolytic activity was observed in these cholesteryl derivatives with 25–30 oxyethylene units. The time course of hemolysis was also measured as a function of the concentrations of surfactant and erythrocyte. Hemolysis started after a certain induction period,, and then apparently proceeded as a first-order reaction with respect to the erythrocyte concentration. The surfactant inducing 50% hemolysis at low concentration had a small value and large rate constant. The maximum amount of adsorption without inducing hemolysis,a ₀, decreased with increasing polyoxyethylene chain length. Chol-E₂₅ has the maximum activity for the solubilization of egg yolk lecithin at 37 °C. Based on these results, the mechanism of hemolysis by these surfactants was quantitatively discussed.     

Effect of gamma-irradiation on surface and catalytic properties of Co3O4 and NiO catalysts

The effects of g-irradiation (0.2-1.6 MGy) on the particle size, specific surface area and catalytic activity of Co₃O₄ and NiO solids were investigated. The investigated solids were prepared by heat treatment of cobalt carbonate at 500 and 700 °C and basic nickel carbonate at 400 °C. The techniques employed were XRD, nitrogen adsorption at -196 °C and decomposition of H₂O₂ at 30-50 °C. The results showed that g-irradiation resulted in a small decrease in the particle size of the investigated solids and effected a progressive increase in their specific surface areas. On the other hand, the exposure of Co₃O₄ and NiO catalysts to a dose of 0.2 MGy resulted in a significant decrease in their catalytic activities, which suffered further progressive decrease upon increasing the doses up to 1.6 MGy. Gamma-irradiation did not modify the activation energy of the catalyzed reaction but decreased the concentration of catalytically active sites without changing their energetic nature. These results were discussed in terms of splitting of the particles of the treated solids and removal of chemisorbed species present in nonstoichiometric cobalt and nickel oxides.     

Polymer adsorption on fine particles; the effects of particle size and its stability

The effects of particle size on polyacrylamide (PAAm,M _w =59×10⁴, 500×10⁴) adsorption were investigated using a series of well-characterized hematite (-Fe₂O₃) dispersions. The -Fe₂O₃ particles with highly monodisperse and nearly spherical shape ranged in radius from 23 nm to 300 nm. the maximum amount of PAAm adsorption (M _m ) in each system, showed a steady increase with decreasing particle radius and was influenced strongly by particle concentrations in the medium. Furthermore, it was realized that the diameter of -Fe₂O₃ particles after treatment with PAAm under different particle concentrations decreased with increasing particle concentration. The relation between particle concentration in the medium and particle size after treatment was also influenced by the medium pH, i.e., at the medium pH close to the isoelectric point of -Fe₂O₃ particles (pH^o=9.2), the particle size after treatment increased with increasing particle concentration. All these results suggest that in the system of ultra-fine particles, the mixing process between particle-particle and polymerparticle will play an important role on the conformation of adsorbed polymer layer.     

Effect of epitaxial growth on the formation of the cobalt catalysts of the Fischer-Tropsch synthesis

Mixed oxides Co_xAl_yO₄ with different Al/Co ratios applied as supports for the catalysts of the Fischer-Tropsch synthesis were prepared using the solid-state chemical reaction. The Co_xAl_yO₄ supports were prepared by modifying gibbsite with various cobalt salts (acetate, nitrate, and basic carbonate). The use of basic cobalt carbonate gives the Co(20%)/Co_xAl_yO₄ catalyst, which provides an increased yield of hydrocarbons C₅₊ and a decreased methane content compared to the impregnation catalyst Co(30%)/Al₂O₃. The introduction of small amounts of rhenium additives makes it possible to enhance the yield of hydrocarbons C₅₊ (179 g m⁻³) and also to increase the selectivity with respect to the C₅–C₁₈ fraction. The introduction of basic cobalt carbonate into the support, most likely, creates favorable conditions for the epitaxial growth of the precursor of the active phase. Dedicated to Academician G. A. Abakumov on the occasion of his 70th birthday. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 9, pp. 1856–1860, September, 2007.     

Effects of PAA additive and temperature on morphology of calcium carbonate particles

Calcium carbonate particles with various shapes were prepared by the reaction of sodium carbonate with calcium chloride in the absence and presence of a polyacrylic acid (PAA) at 25°C and 80°C, respectively. The as-prepared products were characterized with scanning electron microscopy and X-ray diffraction. The effects of pH, temperatures, aging time and concentration of PAA and CaCO₃ on the crystal form and morphologies of the as-prepared CaCO₃ were investigated. The results show that pH, temperatures, concentration of PAA and CaCO₃ are important parameters for the control of morphologies of CaCO₃. Various crystal morphologies of calcite, such as, plates, rhombohedras, rectangles, ellipsoids, cubes, etc. can be obtained depending on the experimental conditions. Especially, the monodispersed cubic calcite particles can be produced by PAA addition at 80°C. Moreover, higher temperature is beneficial to the formation of monodispersed cubic or rectangular calcite particles. This research may provide new insight into the control of morphologies of calcium carbonate and the biomimetic synthesis of novel inorganic materials.     

Interactions of proteins with uniform colloidal hematite and chromium hydroxide particles. I. Adsorption

The adsorption of ovalbumin, -globulin, and lysozyme on uniform spherical hematite and chromium hydroxide particles in aqueous media has been studied as a function of the pH at a constant ionic strength. The uptake of ovalbumin and -globulin was greatest at their isoelectric points and differed little at 10^–2 and 10^–3 mol dm^–3 NaNO₃. The adsorption of lysozyme was strongly influenced by the ionic strength.The deposition of ovalbumin on hematite in the presence of Mg (NO₃)₂ was significantly greater than that with NaNO₃ under otherwise comparable conditions. Dialysis experiments with ovalbumin against magnesium nitrate solutions showed Mg²⁺ to be specifically bound to the protein.The shapes of isotherms indicated monolayer coverage for ovalbumin and multilayer coating for lysozyme for both adsorbents. The shapes of isotherms of -globulin on hematite point to a rearrangement of the protein on the particle surface, while a monolayer was found on chromium hydroxide particles.Supported by the NSF Grant CHE-9108420Part of a Ph.D. thesis