明渠湍流边界层中颗粒的运动与分布

利用直接数值模拟、点球浸入边界法和颗粒离散元法相结合的方法, 模拟了颗粒在明渠湍流边界层中的运动, 并对颗粒的瞬时位置进行了Voronoi 分析, 定量研究了颗粒在湍流边界层中的运动和分布规律. 研究发现:颗粒的输运对湍流的统计特征有影响, 其运动与近壁区湍流拟序结构密切相关, 在"喷发"结构作用下被带离壁面, 在"扫掠" 结构和自身重力作用下回到壁面; 在湍流边界层中, 颗粒倾向于聚集在低流速带, 呈条带状分布;颗粒在大部分时间处于"簇"状态, 偶尔跳跃到"空" 状态, 但能够很快回到邻近低速区域.      

固体颗粒对沟槽湍流边界层影响的实验研究

本文采用粒子图像测速技术(particles image velocimetry, PIV)研究固体颗粒对放置在平板湍流边界层中的平壁和沟槽壁面减阻效果的影响. 实验对清水和加入粒径为155 μm聚苯乙烯颗粒的流法向二维速度场信息进行采集, 对不同工况下的平均速度剖面、雷诺应力和湍流度等统计量进行对比, 分析流体在边界层中的行为. 运用空间局部平均结构函数提取了不同工况湍流边界层喷射?扫掠行为的空间拓扑结构并进行比较. 结果发现, 在不同的壁面条件下, 粒子加入后的对数律区中无量纲速度均略大于清水组, 雷诺切应力有所降低, 湍流度有所减弱. 对于不同流场速度下的沟槽而言, 颗粒的加入均降低了壁面附近的阻力, 而颗粒单独作用于光滑壁面的减阻效果并不明显. 加入粒子后的相干结构数目有所增加, 法向脉动速度下降. 沟槽壁面附近的相干结构数目有所增加, 法向脉动速度在自由来流速度较大时有所上升, 在速度较小时有所下降. 这表明不同减阻状况下的沟槽均能将大涡破碎成更多的涡, 并且粒子的加入强化了这种破碎作用.      

绕壁面小障碍物的湍流边界层研究

采用RNGK－ε模型，对统平板壁面上的条柱、方柱等多种不同形状二维小障碍物的固壁剪切湍流进行数值研究，获得了小障碍物下游回流区及其发展区的时均速度场、回流分离点长度和湍流边界层厚度，计算结果与实验比较吻合良好．结果表明，小障碍物在壁面上的设置，明显地改变了平板壁面边界层的湍流形态和结构．     

输气管道壁面涂料减阻机理的实验研究

用IFA-300热线风速仪以高于对应最小湍流时间尺度的分辨率精细测量了风洞中不同壁面涂料的管道湍流边界层不同法向位置流向速度分量的时间序列信号,利用湍流边界层近壁区域对数律平均速度剖面与壁面摩擦速度、流体黏性系数等内尺度物理量的关系和壁面摩擦速度与壁面摩擦切应力的关系,在准确测量湍流边界层近壁区域对数律平均速度剖面的基础上,间接测量湍流边界层的壁面摩擦阻力．对不同壁面涂料的壁湍流脉动速度信号用子波分析进行多尺度分解,用子波系数的瞬时强度因子和平坦因子检测管道湍流边界层中的多尺度相干结构,提取不同尺度相干结构的条件相位平均波形,对比研究输气管道壁面涂料的减阻机理．     

柔性壁面湍流减阻机理与多尺度相干结构控制的实验研究

用热膜测速仪以高于对应最小湍流时间尺度的分辨率,精细测量了水槽中刚性壁面和柔性壁面平板湍流边界层不同法向位置流向速度分量的时间序列信号,利用湍流边界层近壁区域的对数律平均速度剖面与壁面摩擦速度、流体粘性系数、壁面摩擦切应力等内尺度物理量的关系,在准确测量湍流边界层近壁区域对数律平均速度剖面的基础上,通过非线性迭代求解壁面摩擦速度以及湍流边界层壁面摩擦切应力.结果表明柔性壁的湍流边界层速度分布在对数律层有所上移,缓冲层增厚,说明柔性壁面具有一定的减阻作用. 利用湍流多尺度局部平均结构函数的概念和多尺度局部平均结构函数的瞬时强度因子、平坦因子检测多尺度相干结构及其间歇性的方法,提取了湍流边界层多尺度相干结构的条件相位平均波形.对比研究了刚性壁面和柔性壁面平板湍流边界层近壁区域多尺度相干结构的条件相位平均波形及其间歇性的统计特征,分析了柔性壁面具有减阻作用的物理机理.     

MODELLING AND CALCULATION OF THE TURBULENT BOUNDARY LAYER ON A ROTATING CYLINDER SURFACE WITH STRONG SUCTION 1)

提出了湍流边界层的一种简单、快速计算方法, 用以求解强吸气作用下旋转圆筒表面边界层流动. 首先, 理论分析了同心圆筒间的旋转流体运动, 外筒静止、内筒旋转且为多孔吸气条件. 强吸气情况下旋转流动主要表现为内筒壁面附近的边界层流动, 基于这一事实得到了周向速度分布的解析表达式. 其次, 通过引入新参数扩展Cebeci-Smith代数湍流模型, 使其能考虑流线曲率、壁面吸气、低Reynolds数效应等因素. 针对这些因素的综合影响, 采用解析修正和经验参数对模型进行调整. 同时, 基于Reynolds应力湍流模型的仿真结果, 校准代数湍流模型中的经验参数. 最后, 给出基于广义Cebeci-Smith湍流模型的旋转壁面边界层流动的迭代算法, 该算法适用于需要特殊迭代过程的轴向及周向流动均匀情况. 计算了不同旋转速度和吸气强度组合工况下的边界层流动, 其周向速度和湍流强度分布与基于Reynolds应力湍流模型的计算结果非常接近. 并且表明, 当Reynolds应力湍流模型数值模拟预测内筒边界层为稳定层流时, 该方法也再现了相同初始条件下的层流边界层.     

用平均速度剖面法测量壁湍流摩擦阻力

用IFA300恒温热线风速仪精细测量风洞中不同雷诺数流动条件下的平板湍流边界层近壁区域对数律平均速度剖面．利用平板湍流边界层近壁区域的对数律平均速度剖面与壁面摩擦速度、流体黏性系数等内尺度物理量的关系和壁面摩擦速度与壁面摩擦切应力的关系,在准确测量平板湍流边界层近壁区域对数律平均速度剖面的基础上,测量平板湍流边界层的壁面摩擦阻力．实现了平板湍流边界层壁面摩擦阻力的无干扰或微小干扰测量．该种方法操作简便,不需要在流场中安装测力天平、传感器等复杂的测量装置,不需要对湍流边界层的壁面进行破坏,不会影响湍流边界层壁面附近区域原有的流场条件,是一种切实可行的测量平板湍流边界层壁面摩擦阻力的简便方法．     

强吸气旋转圆筒壁面湍流边界层建模及计算

提出了湍流边界层的一种简单、快速计算方法, 用以求解强吸气作用下旋转圆筒表面边界层流动. 首先, 理论分析了同心圆筒间的旋转流体运动, 外筒静止、内筒旋转且为多孔吸气条件. 强吸气情况下旋转流动主要表现为内筒壁面附近的边界层流动, 基于这一事实得到了周向速度分布的解析表达式. 其次, 通过引入新参数扩展Cebeci-Smith代数湍流模型, 使其能考虑流线曲率、壁面吸气、低Reynolds数效应等因素. 针对这些因素的综合影响, 采用解析修正和经验参数对模型进行调整. 同时, 基于Reynolds应力湍流模型的仿真结果, 校准代数湍流模型中的经验参数. 最后, 给出基于广义Cebeci-Smith湍流模型的旋转壁面边界层流动的迭代算法, 该算法适用于需要特殊迭代过程的轴向及周向流动均匀情况. 计算了不同旋转速度和吸气强度组合工况下的边界层流动, 其周向速度和湍流强度分布与基于Reynolds应力湍流模型的计算结果非常接近. 并且表明, 当Reynolds应力湍流模型数值模拟预测内筒边界层为稳定层流时, 该方法也再现了相同初始条件下的层流边界层.      

Spalding公式在脊状表面湍壁摩擦力测量中的应用

在低速风洞中来流速度一定的情况下使用IFA300恒温热线风速仪测量了光滑表面和两种不同尺寸的脊状表面湍流边界层平均速度分布剖面,并验证了试验段湍流发展的充分性;通过应用Spalding壁面公式使用最小二乘法精准拟合了实验测量的边界层内层速度分布曲线,得到了湍流边界层壁面摩擦速度并进一步求得湍流壁面摩擦应力,较准确地计算出脊状表面的虚拟原点位置,并通过与对数律公式拟合结果比较分析,证实了该方法更加准确有效. 最后分别计算了3种实验模型的湍流边界层动量损失厚度. 通过对比脊状表面与光滑表面动量损失厚度和壁面摩擦应力,反映了动量损失厚度的大小与壁面摩擦应力的大小具有一致性,充分证实了脊状表面在湍流中具有一定的减阻效果.      

TRPIV MEASUREMENT OF DRAG-REDUCTION IN THE TURBULENT BOUNDARY LAYER OVER RIBLETS PLATE

采用高时间分辨率粒子图像测速技术对沟槽壁面平板湍流边界层速度矢量场的时间序列及其统计量进行了实验测量,讨论了在同一来流速度下沟槽壁面对平均速度剖面﹑雷诺切应力及湍流强度的影响. 用流向速度分量的多尺度空间局部平均结构函数辨识壁湍流多尺度相干结构,用条件采样和相位平均技术提取壁湍流多尺度相干结构喷射和扫掠事件的脉动速度、展向涡量的二维空间拓扑形态. 结果表明,与同材料光滑壁面对比,沟槽壁面实现了10.73%的摩阻减小量;沟槽壁面湍流边界层湍流强度及雷诺切应力皆比光滑平板湍流边界层对应统计量小,说明沟槽壁面有效降低了湍流边界层内流体的脉动. 通过比较壁湍流相干结构猝发事件各脉动速度分量与展向涡量的空间分布特征,肯定了沟槽壁面的减阻效果,发现沟槽壁面通过抑制相干结构猝发事件实现减阻.     

The simulation of turbulent particle‐laden channel flow by the Lattice Boltzmann method

We perform direct numerical simulation of three‐dimensional turbulent flows in a rectangular channel, with a lattice Boltzmann method, efficiently implemented on heavily parallel general purpose graphical processor units. After validating the method for a single fluid, for standard boundary layer problems, we study changes in mean and turbulent properties of particle‐laden flows, as a function of particle size and concentration. The problem of physical interest for this application is the effect of water droplets on the turbulent properties of a high‐speed air flow, near a solid surface. To do so, we use a Lagrangian tracking approach for a large number of rigid spherical point particles, whose motion is forced by drag forces caused by the fluid flow; particle effects on the latter are in turn represented by distributed volume forces in the lattice Boltzmann method. Results suggest that, while mean flow properties are only slightly affected, unless a very large concentration of particles is used, the turbulent vortices present near the boundary are significantly damped and broken down by the turbulent motion of the heavy particles, and both turbulent Reynolds stresses and the production of turbulent kinetic energy are decreased because of the particle effects. We also find that the streamwise component of turbulent velocity fluctuations is increased, while the spanwise and wall‐normal components are decreased, as compared with the single fluid channel case. Additionally, the streamwise velocity of the carrier (air) phase is slightly reduced in the logarithmic boundary layer near the solid walls. Copyright © 2015 John Wiley & Sons, Ltd.     

Direct numerical simulation of particle behaviour in the wall region of turbulent flows in horizontal channels

The motion of small particles in the wall region of turbulent channel flows has been investigated using direct numerical simulation. It is assumed that the particle concentration is low enough to allow the use of one-way coupling in the calculations, i.e. the fluid moves the particles but there is no feedback from the particles on the fluid motion. The velocity of the fluid is calculated by using a pseudospectral, direct solution of the Navier-Stokes equations. The calculations indicate that particles tend to segregate into the low-speed regions of the fluid motion near the wall. The segregation tendency depends on the time constant of the particle made non-dimensional with the wall shear velocity and kinematic viscosity. For very small and very large time constants, the particles are distributed more uniformly. For intermediate time constants (of the order 3), the segregation into the low-speed fluid regions is the highest. The finding that segregation occurs for a range of particle time constants is supported by experimental results. The findings regarding the more uniform distributions, however, still remain to be verified against experimental data which is not yet available. For horizontal channel flows, it is also found that particles are resuspended by ejections (of portions of the low-speed streaks) from the wall and are, therefore, primarily associated with low-speed fluid. The smaller particles are flung further upwards and, as they fall back towards the wall, they tend to be accelerated close to the fluid velocity. The larger particles have greater inertia and, consequently, accelerate to lower velocities giving higher relative velocities. This velocity difference, as a function of wall-normal distance, follows the same trend as in experiments but is always somewhat smaller in the calculations. This appears to be due to the Reynolds number for the numerical simulation being smaller than that in the experiment. It is concluded that the average particle velocity depends not only on the wall variables for scaling, but also on outer variables associated with the mean fluid velocity and fluid depth in the channel. This is because fluid depth in combination with the wall shear velocity determines how much time a particle, of a given size and density, spends in the outer flow and, hence, how close it gets to the local fluid velocity.     

稠密气固两相流各向异性颗粒相矩方法

基于气体分子动力学和颗粒动理学方法,考虑颗粒速度脉动各向异性,建立颗粒相二阶矩模型.应用初等输运理论,对三阶关联项进行模化和封闭.考虑颗粒与壁面之间的能量传递和交换,建立颗粒相边界条件模型.采用Koch等计算方法模拟气固脉动速度关联矩.考虑气体-颗粒间相互作用,建立稠密气体-颗粒流动模型.数值模拟提升管内气固两相流动特性,模拟结果表明提升管内颗粒相湍流脉动具有明显的各向异性.预测颗粒速度、浓度和颗粒脉动速度二阶矩与Tartan等实测结果相吻合.模拟结果表明轴向颗粒速度脉动强度约为平均颗粒相脉动强度的1.5倍,轴向颗粒脉动能大约是径向颗粒脉动能3.0倍.     

Hydromagnetic Stokes flow in a rotating fluid with suspended small particles

An initial value investigation is made of the motion of an incompressible, viscous conducting fluid with embedded small spherical particles bounded by an infinite rigid non-conducting plate. Both the plate and the fluid are in a state of solid body rotation with constant angular velocity about an axis normal to the plate. The flow is generated in the fluid-particle system due to non-torsional oscillations of a given frequency superimposed on the plate in the presence of a transverse magnetic field. The operational method is used to derive exact solutions for the fluid and the particle velocities, and the wall shear stress. The small and the large time behaviour of the solutions is discussed in some detail. The ultimate steady-state solutions and the structure of the associated boundary layers are determined with physical implications. It is shown that rotation and magnetic field affect the motion of the fluid relatively earlier than that of the particles when the time is small. The motion for large times is set up through inertial oscillations of frequency equal to twice the angular velocity of rotation. The ultimate boundary layers are established through inertial oscillations. The shear stress at the plate is calculated for all values of the frequency parameter. The small and large-time behaviour of the shear stress is discussed. The exact solutions for the velocity of fluid and the wall shear stress are evaluated numerically for the case of an impulsively moved plate. It is found that the drag and the lateral stress on the plate fluctuate during the non-equilibrium process of relaxation if the rotation is large. The present analysis is very general in the sense that many known results in various configurations are found to follow as special cases.     

Simulation of particles released near the wall in a turbulent boundary layer

A direct numerical simulation was used along with a Lagrangian particle tracking technique to study particle motion in a horizontal, spatially developing turbulent boundary layer along an upper-wall (with terminal velocity directed away from the wall). The objective of the research was to study particle diffusion, dispersion, reflection, and mean velocity in the context of two parametric studies: one investigated the effect of the drift parameter (the ratio of particle terminal velocity to fluid friction velocity) for a fixed and finite particle inertia, and the second varied the drift parameter and particle inertia by the same amount (i.e. for a constant Froude number). A range of drift parameters from 10⁻⁴ to 10⁰ were considered for both cases. The particles were injected into the simulation at a height of four wall units for several evenly distributed points across the span and a perfectly elastic wall collision was specified at one wall unit.Statistics collected along the particle trajectories demonstrated a transition in particle movement from one that is dominated by diffusion to one that is dominated by gravity. For small and intermediate sized particles (i.e. ones with outer Stokes numbers and drift parameters much less than unity) transverse diffusion away from the wall dominated particle motion. However, preferential concentration is seen near the wall for intermediate-sized particles due to inhomogeneous turbulence effects (turbophoresis), consistent with previous channel flow studies. Particle–wall collision statistics indicated that impact velocities tended to increase with increasing terminal velocity for small and moderate inertias, after which initial conditions become important. Finally, high relative velocity fluctuations (compared to terminal velocity) were found as particle inertia increased, and were well described with a quasi-one-dimensional fluctuation model.     

Lagrangian model on the turbulent motion of small solid particle in turbulent boundary layer flows

.Intr0ductionSurfaceerosionofmaterialbysolid-particleimpactisanimportantprobleminmultiphaseflowindustriaIdevicesandthecharacteristicsoftheparticIe'smotioninaturbulentboundarylayerflowisthebaseofthestudyofthematerialsurfaceerosion.Manycalculationmodelshave…     

The effect of particles on fluid turbulence in a turbulent boundary layer over a cylinder

The turbulent fluid and particle interaction in the turbulent boundary layer for cross flow over a cylinder has been experimentally studied. A phase-Doppler anemometer was used to measure the mean and fluctuating velocities of both phases. Two size ranges of particles (30μm–60μm and 80μm–150μm) at certain concentrations were used for considering the effects of particle sizes on the mean velocity profiles and on the turbulent intensity levels. The measurements clearly demonstrated that the larger particles damped fluid turbulence. For the smaller particles, this damping effect was less noticeable. The measurements further showed a delay in the separation point for two phase turbulent cross flow over a cylinder. The project supported by the National Natural Science Foundation of China     

Direct numerical simulation of particle-laden plane turbulent wall jet and the influence of Stokes number

The distribution and motion of inertial particles in plane turbulent wall jet are investigated using direct numerical simulation, under the assumption of one-way coupling. To our knowledge, this appears to be the first direct numerical simulation of a particle-laden plane turbulent wall jet. It is shown that, in outer part of the wall jet, the behaviour of particles closely resembles that of a free plane jet. Due to the streamwise decay of particle Stokes number, the particle streaks formed in the near wall region of the wall jet are characterized by their intensity variation, which differs significantly from those in the channel flow. The streamwise growth of the particle velocity half-width is approximately equal to that of the fluid velocity half-width and the maximum velocity of particles decays slower than that of fluid due to inertia. The outer scaling can collapse the mean particle velocity in both the inner and outer region for heavier particles. In the buffer region, the particle–fluid velocity difference can be negative or positive depending on the Stokes number since there are two competing effects, namely the memory effect and turbophoresis. In the viscous region, the larger particles are on average faster than fluid and the velocity difference is found to be self-similar depending on outer Stokes number. The near-wall distribution of velocity difference is significantly correlated with the presence of high-momentum particles which are entrained by vortical structures generated in the outer region of the wall jet. These results are useful for environmental and engineering applications.