Synthesis and Optical Properties of Novel Red-Emitting PbNb<Subscript>2</Subscript>O<Subscript>6</Subscript>: Eu<Superscript>3+</Superscript> Phosphors

Undoped and PbNb₂O_6:Eu³⁺ (1.0 ≤ x ≤ 6.0 mol%) phosphors were synthesized at 1100 °C for 3.5 h by the conventional solid state reaction method. Synthesized PbNb₂O₆:Eu³⁺ phosphors were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive spectroscopy (EDS) and Photoluminescence (PL) analyses. The PL spectra showed series of excitation peaks between 350 and 430 nm due to the 4f–4f transitions of Eu³⁺. For 395.0 nm excitation, emission spectra of Eu³⁺ doped samples were observed at 591 nm (orange) and 614 nm (red) due to the ⁵D₀ → ⁷F₁ transitions and ⁵D₀ → ⁷F₂ transitions, respectively. PL analysis results also showed that the emission intensity increased by increasing Eu³⁺ ion content. No concentration quenching effect was observed. The CIE chromaticity color coordinates (x,y) of the PbNb₂O₆:Eu³⁺ phosphors were found to be in the red region of the chromaticity diagram.     

Red,Yellow, Blue and Green Emission from Eu<Superscript>3+</Superscript>, Dy<Superscript>3+</Superscript> and Bi<Superscript>3+</Superscript> Doped Y<Subscript>2</Subscript>O<Subscript>3</Subscript>nano-Phosphors

Rare earth elements (RE = Eu³⁺& Dy³⁺)and Bi³⁺ doped Y₂O₃ nanoparticles were synthesized by urea hydrolysis method in ethylene glycol, which acts as reaction medium as well as a capping agent, at a low temperature of 140 °C,followed by calcination of the obtained product. Transmission electron microscope (TEM) images reveals that ovoid shaped Y₂O₃ nanoparticles of around 22–24 nm size range were obtained in this method. The respective RE and Bi³⁺ doped Y₂O₃ precursor nanoparticles when heated at 600 and 750 °C, retains the same shape as that of the as-synthesized Y₂O₃ precursor samples. From EDAX spectra, the incorporation of RE ions into the host has been studied. XRD pattern reveals the crystalline nature of the heated nanoparticles and indicate the absence of any impurity phase other than cubic Y₂O₃.However, the as-synthesized nanoparticles were highly amorphous without the presence of any sharp XRD peaks. Photoluminescence study suggests that the synthesized samples could be used as red (Eu³⁺), yellow (Dy³⁺), blue and green (Bi³⁺)emitting phosphors.     

Enhanced Up-Conversion Emission in Al<Superscript>3+</Superscript> Co-Doped ZnGa<Subscript>2</Subscript>O<Subscript>4</Subscript>:Yb<Superscript>3+</Superscript>,Tm<Superscript>3+</Superscript> Powder Phosphors

Yb³⁺-Tm³⁺ co-doped up-conversion powder phosphors using Zn(Al_xGa_1-x)₂O₄ (ZAGO) as the host materials were synthesized via solid-state reaction successfully. In addition, the morphology, structural characterization and up-conversion luminescent properties were all investigated by scanning electron microscope (SEM), x-ray diffraction (XRD) and fluorescence spectrophotometer (F-7000), respectively. Under the excitation of a 980 nm laser, all as-prepared powders can carry out blue emission at about 477 nm (corresponding to ¹G₄ → ³H₆ transition of Tm³⁺ ions), and red emission at about 691 nm (attributed to ³F₃ → ³H₆ transition of Tm³⁺ ions). Also, the influence of doping Al³⁺ ions were investigated. In brief, the doping of Al³⁺ ions has no effect on the position of emission peak. Howbeit the up-conversion efficiency and intensity of ZAGO:Yb,Tm phosphors are stronger than ZGO:Yb,Tm and ZAO:Yb,Tm phosphors, while the crystallinity is the opposite. More particularly, all as-prepared powder phosphors emit strong luminescence, which is observable by the naked eye, demonstrating the potential applications in luminous paint, luminescent dye, etc.     

Microstructural and Radioluminescence Characteristics of Nd<Superscript>3+</Superscript> Doped Columbite-Type SrNb<Subscript>2</Subscript>O<Subscript>6</Subscript> Phosphor

Undoped and different concentration Nd³⁺ doped SrNb₂O₆ powders with columbite structure were synthesized by molten salt process using a mixture of strontium nitrate and niobium (V) oxide and NaCl-KCl salt mixture as a flux under relatively low calcining temperature. X-ray diffraction analysis results indicated that SrNb₂O₆ phases found to be orthorhombic columbite single phase for undoped, 0.5 and 3 mol% Nd³⁺ doping concentrations. Phase composition of the powders was examined by SEM-EDS analyses. Radioluminescence properties of Nd³⁺ doped samples from UV to near-IR spectral region were studied. The emissions increased with the doping concentration of up to 3 mol%, and then decreased due to concentration quenching effect. There is a sharp emission peak around 880 nm associated with ⁴F_5/2 → ⁴I_9/2 transition in the Nd³⁺ ion between 300 and 1100 nm. The broad emission band intensity was observed from 400 to 650 nm where the peak intensities increased by increasing Nd³⁺ doping concentration. All the measurements were taken under the room temperature.     

Preparation and Photoluminescence of Sm <Superscript>3+</Superscript> Doped YAlO <Subscript>3</Subscript> Phosphor

YAlO₃: Sm³⁺ phosphor has been synthesized by the solid state reaction method with calcium flouride used as a flux. The resulting YAlO₃: Sm³⁺ phosphor was characterized by X-ray diffraction (XRD) technique, Fourier transmission infrared spectroscopy (FTIR), photoluminescence . . PL excitation spectrum was found at 254,332,380,400,407, 603 and 713 nm. Under excitation of UV(713 nm) YAlO₃: Sm³⁺ (0–3 %) broad band emission were observed from 400 to 790 nm with a maximum around 713 nm of YAlO₃ host lattice accompanied by weak emission of Sm³⁺ (⁴G_5/2 – ⁶H_5/2, ⁶H_7/2,⁶H_9/2) transitions. The results of the XRD show that obtained YAlO₃: Sm³⁺ phosphor has a orthorhombic structure. The study suggested that Sm³⁺ doped phosphors are potential luminescence material for laser diode pumping and inorganic scintillators.     

PL Properties of Sr<Subscript>2</Subscript>CeO<Subscript>4</Subscript> With Eu<Superscript>3+</Superscript> and Dy<Superscript>3+</Superscript> for Solid State Lighting Prepared by Precipitation Method

Photoluminescence studies of pure and Dy³⁺, Eu³⁺ doped Sr₂CeO₄ compounds are presented by oxalate precipitation method for solid state lighting. The prepared samples also characterized by XRD, SEM (EDS) and FTIR spectroscopy. The pure Sr₂CeO₄ compound displays a broad band in its emission spectrum when excited with 280 nm wavelength, which peaks centered at 488 nm, which is due to the energy transfer between the molecular orbital of the ligand and charge transfer state of the Ce⁴⁺ ions. Emission spectra of Sr₂CeO₄ with different concentration of Dy³⁺ ions under near UV radiation excitation, shows that intensity of luminescence spectra is found to be affected by Dy³⁺ ions, and it increases with adding some percentages of Dy³⁺ ions. The maximum doping concentration for quenching is found to be Dy³⁺?=?0.2 mol % to Sr²⁺ions. The observed broad spectrum from 400 to 560 nm is mainly due to CT transitions in Sr₂CeO₄ matrix and some fractional contribution of transitions between ⁴F_9/2 → ⁶H_15/2 of Dy³⁺ ions. Secondly the effect of Eu³⁺ doping at the Sr²⁺ site in Sr₂CeO₄, have been studied. The results obtained by doping Eu³⁺ concentrations (0.2 mol% to 1.5 mol%), the observed excitation and emission spectra reveal excellent energy transfer between Ce⁴⁺ and Eu³⁺. The phenomena of concentration quenching are explained on the basis of electron phonon coupling and multipolar interaction. This energy transfer generates white light with a color tuning from blue to red, the tuning being dependent on the Eu³⁺ concentration. The results establish that the compound Sr₂CeO₄ with Eu³⁺?=?1 mol% is an efficient “single host lattice” for the generation of white lights under near UV-LED and blue LED irradiation. The commission internationale de I’Eclairage (CIE) coordinates were calculated by Spectrophotometric method using the spectral energy distribution of prepared phosphors.     

Green,blue, red,near-infrared up-conversion luminescence of Yb<Superscript>3+</Superscript>/Er<Superscript>3+</Superscript>/Tm<Superscript>3+</Superscript> co-doped YVO<Subscript>4</Subscript> nanoparticles

YVO₄:Yb³⁺,Er³⁺; YVO₄:Yb³⁺,Tm³⁺; and YVO₄:Yb³⁺,Er³⁺,Tm³⁺ were all synthesized via sol-gel method with a subsequent thermal treatment. Specifically, YVO₄:Yb³⁺,Er³⁺,Tm³⁺ phosphors were prepared with different annealing temperatures to study the influence of temperature. The transmission electron microscope (TEM), scanning electron microscope (SEM), X-ray diffractometer (XRD), and photoluminescent (PL) spectrofluorometer were used to investigate the morphology, crystal structure, and up-conversion luminescent properties of all samples. In summary, all samples were granular-like nanoparticles and well crystallized with the same tetragonal phase as YVO₄. Under the irradiation at 980 nm, YVO₄:Yb³⁺,Er³⁺ phosphors can generate green emission at 525 and 553 nm and red emission at 657 nm, while YVO₄:Yb³⁺,Tm³⁺ phosphors can generate blue emission at 476 nm, red emission at 648 nm, and near-infrared emission at 800 nm. Notably, YVO₄:Yb³⁺,Er³⁺,Tm³⁺ samples can exhibit green emission, blue emission, red emission, and near-infrared emission at the same time, which might endow the as-prepared samples with potential applications in many fields, such as luminous paint, infrared detection, and biological label.     

Luminescence in Dy<Superscript>3+</Superscript> and Eu<Superscript>3+</Superscript> Activated K<Subscript>3</Subscript>Al<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

The Dy³⁺ and Eu³⁺ activated K₃Al₂ (PO₄)₃ phosphors were prepared by a combustion synthesis. From a powder X-ray diffraction (XRD) analysis the formation of K₃Al₂ (PO₄)₃ was confirmed. In the photoluminescence emission spectra, the K₃Al₂(PO₄)₃:Dy³⁺ phosphor emits two distinctive colors: blue and yellow whereas K₃Al₂(PO₄)₃:Eu³⁺ emits red color. Thus the combination of colors gives BYR (blue–yellow–red) emissions can produce white light. These phosphors exhibit a strong absorption between 340 and 400 nm which suggest that present phosphor is a promising candidate for producing white light-emitting diodes (LED).     

Luminescence thermometry using Gd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript>

In this paper we study the possibility of using the synthesized nanopowder samples of Gd₂Zr₂O₇:Eu³⁺ for temperature measurements by analyzing the temperature effects on its photoluminescence. The nanopowder was prepared by solution combustion synthesis method. The photoluminescence spectra used for analysis of Gd₂Zr₂O₇:Eu³⁺ nano phosphor optical emission temperature dependence were acquired using continuous laser diode excitation at 405 nm. The temperature dependencies of line emission intensities of transitions from ⁵D₀ and ⁵D₁ energy levels to the ground state were analyzed. Based on this analysis we use the two lines intensity ratio method for temperature sensing. Our results show that the synthesized material can be efficiently used as thermographic phosphor up to 650 K.     

Photolumiscent Properties of Nanorods and Nanoplates Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript>

Nanorods and nanoplates of Y₂O₃:Eu³⁺ powders were synthesized through the thermal decomposition of the Y(OH)₃ precursors using a microwave-hydrothermal method in a very short reaction time. These powders were analyzed by X-ray diffraction, field emission scanning electron microscopy, Fourrier transform Raman, as well as photoluminescence measurements. Based on these results, these materials presented nanoplates and nanorods morphologies. The broad emission band between 300 and 440 nm ascribed to the photoluminescence of Y₂O₃ matrix shifts as the procedure used in the microwave-hydrothermal assisted method changes in the Y₂O₃:Eu³⁺ samples. The presence of Eu³⁺ and the hydrothermal treatment time are responsible for the band shifts in Y₂O₃:Eu³⁺ powders, since in the pure Y₂O₃ matrix this behavior was not observed. Y₂O₃:Eu³⁺ powders also show the characteristic Eu³⁺ emission lines at 580, 591, 610, 651 and 695 nm, when excited at 393 nm. The most intense band at 610 nm is responsible for the Eu³⁺ red emission in these materials, and the Eu³⁺ lifetime for this transition presented a slight increase as the time used in the microwave-hydrothermal assisted method increases.     

Sol-gel method and luminescence properties of the ZrO<Subscript>2</Subscript>:Eu<Superscript>3+</Superscript> phosphors with different charge compensation

Eu³⁺-doped ZrO₂ phosphors with different charge compensators (Li⁺, Na⁺, K⁺) were prepared by the sol-gel method. The properties of the as-obtained samples are characterized by X-ray diffraction, scanning electron microscope, photoluminescence spectra, and decay curve. The results show that ZrO₂:Eu³⁺ phosphors with different charge compensation are mixed phase of tetragonal and monoclinic phase, and the volume fraction of tetragonal phase of ZrO₂:Eu³⁺/Na⁺ phosphor is bigger than the other phosphors. The phosphors can emit strong red light at 606~616 nm (⁵D₀ → ⁷F₂) excited by ultraviolet light (395 nm). Compared with two charge compensation patterns in the ZrO₂:Eu³⁺, it has been found that ZrO₂:Eu³⁺ phosphors used Na⁺ as charge compensator show greatly enhanced red emission under 395 nm excitation and longer luminescence lifetime.     

Effect of sintering temperature of Ce<Superscript>3+</Superscript>-doped Lu<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript> phosphors on light emission and properties of crystal structure for white-light-emitting diodes

The effect of the sintering temperature of Ce³⁺-doped Lu₃Al₅O₁₂ (Ce-LuAG) phosphors on the emission and properties of the crystal structure was studied. A cathodoluminescence peak at 317 nm, which was assigned to lattice defects, was exhibited in addition to emission peaks at 508 and 540 nm for the Ce-LuAG phosphors. The intensities of the 317 nm emission peak for the phosphors with mean particle diameters of 5.0 and 10.0 µm formed at a low sintering temperature of 1430 °C were higher than those for the phosphors with mean particle diameters of 18.0 and 20.5 µm formed at a high sintering temperature of 1550 °C. In contrast, the electroluminescence spectra for fabricated white-light-emitting diodes (LEDs) using the phosphors revealed that the intensity of the peak at 540 nm was strong for the mean particle diameters of 18.0 and 20.5 µm. The intensity of the 540 nm peak, which is attributed to the 4f→5d transition of the Ce³⁺ activator, showed a dependence on the sintering temperature. The relationship between the optical properties and the lattice defects is discussed.     

Synthesis and luminescent properties of Eu<Superscript>3+</Superscript>- and Eu<Superscript>2+</Superscript>-activated sodium pyrophosphate Na<Subscript>4</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

The luminescent properties of Eu³⁺ and Eu²⁺ ions in sodium pyrophosphate, Na₄P₂O₇, have been studied. The excitation spectrum of the Eu³⁺ emission in Na₄P₂O₇ consists of several sets of bands in the range 280–535 nm due to 4f–4f transitions of Eu³⁺ ions and a broad band with a maximum at about 240 nm interpreted to be due to a charge transfer (CT) transition from oxygen 2p states to empty states of the Eu³⁺ 4f⁶-configuration. Although the CT band energy is large enough, the quantum efficiency (η) of the Eu³⁺ emission in Na₄P₂O₇ under CT excitation was estimated to be very low (η ≤ 0.01). In terms of a configurational coordinate model, this fact is interpreted as a result of the high efficiency of a radiationless relaxation from the CT state to the ⁷F₀ ground state of Eu³⁺ ions occupying sodium sites in Na₄P₂O₇. A strong reducing agent is required in order to stabilize Eu²⁺ ions in Na₄P₂O₇ during the synthesis. Several nonequivalent Eu²⁺ luminescence centers in Na₄P₂O₇ were found.     

Luminescent properties and the morphology of SrMoO<Subscript>4</Subscript>:Eu<Superscript>3+</Superscript> powders synthesized <Emphasis Type="Italic">via</Emphasis> combining sol-gel and solid-state route

SrMoO₄:Eu³⁺ red phosphors were prepared by combining sol-gel and solid-state route. Citric acid and ethylenediaminetetraacetic acid (EDTA), employed as the chelating agents, were added to the aqueous solutions of metal nitrates. X-ray diffraction (XRD) and photoluminescent spectra techniques (PL) were used to characterize the resultant powders. The results indicated the obtained SrMoO₄:Eu³⁺ phosphors were fine powders with a particle size of 50 nm. The effects of synthesizing conditions were also investigated and optimized, which included the synthesis temperature and the activator concentration on the luminescent intensity. Compared with SrMoO₄:Eu³⁺ phosphors prepared by Solid-state reaction SrMoO₄:Eu³⁺ phosphors prepared by combining sol-gel and solid-state route showed appropriate particle size and a higher emission intensity.     

Tunable bluish green to yellowish green Ca<Subscript>2(1-x)</Subscript>Sr<Subscript>2x</Subscript>Al<Subscript>2</Subscript>SiO<Subscript>7</Subscript>:Eu<Superscript>2+</Superscript> phosphors for potential LED application

A series of solid solutions with a general formula of Ca_2(1-x)Sr_2xAl₂SiO₇:Eu²⁺ were synthesized by a high temperature solid state reaction. The structure, diffuse reflection spectra, photoluminescence spectra, color-coordinate parameters and lifetimes of phosphors were investigated. XRD results show that Ca₂Al₂SiO₇ is totally miscible with Sr₂Al₂SiO₇. These solid solution phosphors show a broad excitation band of 350–450 nm that matches well with the output lights of near-UV LEDs and tunable emission from bluish green to yellowish green. These optical properties originate from the 4f⁷–4f⁶5d transition of Eu²⁺ ions. The crystal field strength was considered to be tailed by controlling the host composition, which leads to the shift of absorption band and emission band, and the varying of color coordinates. PACS  78.55.-m; 42.70.-a; 61.05.C-     

On the Luminescence of Ce<Superscript>3+</Superscript>, Eu<Superscript>3+</Superscript>, and Tb<Superscript>3+</Superscript> in Novel Borate LiSr<Subscript>4</Subscript>(BO<Subscript>3</Subscript>)<Subscript>3</Subscript>

This paper reports on the photoluminescence (PL) and time-resolved properties of Ce³⁺, Eu³⁺, and Tb³⁺ in novel LiSr₄(BO₃)₃ powder phosphors. Ce³⁺ shows an emission band peaking at 420 nm under 350-nm UV excitation. Energy transfer from Ce³⁺ to Mn²⁺ takes place in the co-doped samples. Eu³⁺ shows red emission under near UV excitation. LiSr₄(BO₃)₃:Eu³⁺ phosphor could be a suitable candidate for phosphor-converted solid state lighting. The luminescence lifetime is 2.13 ms for Eu³⁺ in LiSr₄(BO₃)₃:0.001Eu³⁺. As Eu³⁺ concentration increasing, the decay curves deviate from exponential behavior. Tb³⁺ shows the strongest ⁵D₄→⁷ F₅ emission line at 540 nm. Decay curves of ⁵D₄→⁷ F₅ and ⁵D₃→⁷ F₅ emission with different Tb³⁺ concentrations were also measured. Cross-relaxation process is discussed based on the decay curves.     

A novel white light-emitting diode (w-LED) fabricated with Sr<Subscript>6</Subscript>BP<Subscript>5</Subscript>O<Subscript>20</Subscript>:Eu<Superscript>2+</Superscript> phosphor

Sr₆BP₅O₂₀:Eu²⁺ phosphor was prepared by the solid-state reaction method under a weak reductive atmosphere and the photoluminescence properties were studied systematically. The bluish-green emission band of Sr₆BP₅O₂₀:Eu²⁺ phosphor is peaking at 475 nm, and the excitation bands are broad with peaks at about 290 and 365 nm with a shoulder around 390 nm, respectively. By combining with Ga(In)N-based near-ultraviolet LEDs, a bluish-green LED was fabricated based on the Sr₆BP₅O₂₀:Eu²⁺ phosphor, and a novel intense white LED was fabricated based on the bluish-green phosphor Sr₆BP₅O₂₀:Eu²⁺ and the red phosphor (Sr,Ca)₅(PO₄)₃Cl:Eu²⁺,Mn²⁺. When this two-phosphor white LED is operated under 20-mA forward-bias current at room temperature, the Commission Internationale de l’Eclairage(CIE) chromaticity coordinates (x,y), the correlated color temperature Tc, and the color rendering index Ra are calculated to be (0.3281,0.3071), 5687 K, and 87.3, respectively. The dependence of the bluish-green and two-phosphor white LEDs on different forward-bias currents from 5 mA to 50 mA shows a similar behavior. As the current increases, the relative intensity simultaneously increases. The CIE chromaticity coordinates (x,y) of the two-phosphor white LED tend to decrease. Consequently, the correlated color temperature Tc increases from 3800 K to 9400 K and the color rendering index Ra of the two-phosphor white LED increases from 83.4 to 91.8 simultaneously. PACS 07.60.-j; 42.70.-a; 71.55.Eq     

Eu<Superscript>3+</Superscript> As a Luminescent Probe for Studying the Structure of R<Subscript>2</Subscript>O<Subscript>3</Subscript> Materials (R = Y,Eu, and Gd)

Spectra of Eu³⁺ in various dielectric matrices (Gd₂O₃:Eu³⁺, Y₂O₃:Eu³⁺, Eu₂O₃, and mSiO₂/Gd₂O₃:Eu³⁺ mesoporous particles) are studied by local cathodoluminescence. The results allowed identification of the local environment of Er³⁺ ions in amorphous samples and detection of the monoclinic Eu₂O₃ phase impurity in samples with yttrium oxide. The cathodoluminescence spectra of chemically pure Y₂O₃, Eu₂O₃, and Gd₂O₃ are recorded. Conclusions about the structural features of the materials are made and confirmed by other methods (XRD and EPMA).     

Luminescence characteristics of energy transfer between Ce<Superscript>3+</Superscript> and Eu<Superscript>2+</Superscript> in NaMgPO<Subscript>4</Subscript> phosphor

Powder samples of NaMgPO₄ doped with Eu²⁺ and Ce³⁺ were prepared and their photoluminescence spectra were systemically studied. Energy transfer from Ce³⁺ to Eu²⁺ in NaMgPO₄ phosphor was observed by investigating the optical properties from photoluminescence spectra in Eu²⁺ or Ce³⁺ singly doped and Eu²⁺–Ce³⁺ codoped sodium magnesium orthophosphates, NaMgPO₄. The enhancement of UV excitation is attributed to energy transfer from Ce³⁺ to Eu²⁺, and Ce³⁺ plays a role as a sensitizer. Ce³⁺–Eu²⁺ codoped NaMgPO₄ phosphors in which Eu²⁺ can be efficiently excited by 390 nm are potential candidates for phosphor-converted LEDs.     

luminescence of BaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript> crystals activated by Eu<Superscript>2+</Superscript> and Ce<Superscript>3+</Superscript> ions

We have studied the effect of doping with Eu²⁺ and Ce³⁺ ions on the photoluminescence (PL) of BaGa₂Se₄ crystals in the temperature range 77–300 K. We have established that the broad bands with maxima at wavelengths 456 nm and 506 nm observed in the photoluminescence spectra of BaGa₂Se₄:Ce³⁺ crystals are due to intracenter transitions 5d → ²F_7/2 and 5d →²F_5/2 of the Ce³⁺ ions, while the broad photoluminescence band with maximum at 521 nm in the spectrum of BaGa₂Se₄:Eu²⁺ is associated with 4f⁶ 5d → 4f⁷ (⁸S_7/2) transitions of the Eu²⁺ ion. We show that in BaGa₂Se₄:Eu²⁺,Ce³⁺ crystals, excitation energy is transferred from the Ce³⁺ ions to the Eu²⁺ ions.