Enhanced Up-Conversion Emission in Al<Superscript>3+</Superscript> Co-Doped ZnGa<Subscript>2</Subscript>O<Subscript>4</Subscript>:Yb<Superscript>3+</Superscript>,Tm<Superscript>3+</Superscript> Powder Phosphors

Yb³⁺-Tm³⁺ co-doped up-conversion powder phosphors using Zn(Al_xGa_1-x)₂O₄ (ZAGO) as the host materials were synthesized via solid-state reaction successfully. In addition, the morphology, structural characterization and up-conversion luminescent properties were all investigated by scanning electron microscope (SEM), x-ray diffraction (XRD) and fluorescence spectrophotometer (F-7000), respectively. Under the excitation of a 980 nm laser, all as-prepared powders can carry out blue emission at about 477 nm (corresponding to ¹G₄ → ³H₆ transition of Tm³⁺ ions), and red emission at about 691 nm (attributed to ³F₃ → ³H₆ transition of Tm³⁺ ions). Also, the influence of doping Al³⁺ ions were investigated. In brief, the doping of Al³⁺ ions has no effect on the position of emission peak. Howbeit the up-conversion efficiency and intensity of ZAGO:Yb,Tm phosphors are stronger than ZGO:Yb,Tm and ZAO:Yb,Tm phosphors, while the crystallinity is the opposite. More particularly, all as-prepared powder phosphors emit strong luminescence, which is observable by the naked eye, demonstrating the potential applications in luminous paint, luminescent dye, etc.     

Synthesis and Optical Properties of Novel Red-Emitting PbNb<Subscript>2</Subscript>O<Subscript>6</Subscript>: Eu<Superscript>3+</Superscript> Phosphors

Undoped and PbNb₂O_6:Eu³⁺ (1.0 ≤ x ≤ 6.0 mol%) phosphors were synthesized at 1100 °C for 3.5 h by the conventional solid state reaction method. Synthesized PbNb₂O₆:Eu³⁺ phosphors were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive spectroscopy (EDS) and Photoluminescence (PL) analyses. The PL spectra showed series of excitation peaks between 350 and 430 nm due to the 4f–4f transitions of Eu³⁺. For 395.0 nm excitation, emission spectra of Eu³⁺ doped samples were observed at 591 nm (orange) and 614 nm (red) due to the ⁵D₀ → ⁷F₁ transitions and ⁵D₀ → ⁷F₂ transitions, respectively. PL analysis results also showed that the emission intensity increased by increasing Eu³⁺ ion content. No concentration quenching effect was observed. The CIE chromaticity color coordinates (x,y) of the PbNb₂O₆:Eu³⁺ phosphors were found to be in the red region of the chromaticity diagram.     

Luminescence thermometry using Gd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript>

In this paper we study the possibility of using the synthesized nanopowder samples of Gd₂Zr₂O₇:Eu³⁺ for temperature measurements by analyzing the temperature effects on its photoluminescence. The nanopowder was prepared by solution combustion synthesis method. The photoluminescence spectra used for analysis of Gd₂Zr₂O₇:Eu³⁺ nano phosphor optical emission temperature dependence were acquired using continuous laser diode excitation at 405 nm. The temperature dependencies of line emission intensities of transitions from ⁵D₀ and ⁵D₁ energy levels to the ground state were analyzed. Based on this analysis we use the two lines intensity ratio method for temperature sensing. Our results show that the synthesized material can be efficiently used as thermographic phosphor up to 650 K.     

PL Properties of Sr<Subscript>2</Subscript>CeO<Subscript>4</Subscript> With Eu<Superscript>3+</Superscript> and Dy<Superscript>3+</Superscript> for Solid State Lighting Prepared by Precipitation Method

Photoluminescence studies of pure and Dy³⁺, Eu³⁺ doped Sr₂CeO₄ compounds are presented by oxalate precipitation method for solid state lighting. The prepared samples also characterized by XRD, SEM (EDS) and FTIR spectroscopy. The pure Sr₂CeO₄ compound displays a broad band in its emission spectrum when excited with 280 nm wavelength, which peaks centered at 488 nm, which is due to the energy transfer between the molecular orbital of the ligand and charge transfer state of the Ce⁴⁺ ions. Emission spectra of Sr₂CeO₄ with different concentration of Dy³⁺ ions under near UV radiation excitation, shows that intensity of luminescence spectra is found to be affected by Dy³⁺ ions, and it increases with adding some percentages of Dy³⁺ ions. The maximum doping concentration for quenching is found to be Dy³⁺?=?0.2 mol % to Sr²⁺ions. The observed broad spectrum from 400 to 560 nm is mainly due to CT transitions in Sr₂CeO₄ matrix and some fractional contribution of transitions between ⁴F_9/2 → ⁶H_15/2 of Dy³⁺ ions. Secondly the effect of Eu³⁺ doping at the Sr²⁺ site in Sr₂CeO₄, have been studied. The results obtained by doping Eu³⁺ concentrations (0.2 mol% to 1.5 mol%), the observed excitation and emission spectra reveal excellent energy transfer between Ce⁴⁺ and Eu³⁺. The phenomena of concentration quenching are explained on the basis of electron phonon coupling and multipolar interaction. This energy transfer generates white light with a color tuning from blue to red, the tuning being dependent on the Eu³⁺ concentration. The results establish that the compound Sr₂CeO₄ with Eu³⁺?=?1 mol% is an efficient “single host lattice” for the generation of white lights under near UV-LED and blue LED irradiation. The commission internationale de I’Eclairage (CIE) coordinates were calculated by Spectrophotometric method using the spectral energy distribution of prepared phosphors.     

Green,blue, red,near-infrared up-conversion luminescence of Yb<Superscript>3+</Superscript>/Er<Superscript>3+</Superscript>/Tm<Superscript>3+</Superscript> co-doped YVO<Subscript>4</Subscript> nanoparticles

YVO₄:Yb³⁺,Er³⁺; YVO₄:Yb³⁺,Tm³⁺; and YVO₄:Yb³⁺,Er³⁺,Tm³⁺ were all synthesized via sol-gel method with a subsequent thermal treatment. Specifically, YVO₄:Yb³⁺,Er³⁺,Tm³⁺ phosphors were prepared with different annealing temperatures to study the influence of temperature. The transmission electron microscope (TEM), scanning electron microscope (SEM), X-ray diffractometer (XRD), and photoluminescent (PL) spectrofluorometer were used to investigate the morphology, crystal structure, and up-conversion luminescent properties of all samples. In summary, all samples were granular-like nanoparticles and well crystallized with the same tetragonal phase as YVO₄. Under the irradiation at 980 nm, YVO₄:Yb³⁺,Er³⁺ phosphors can generate green emission at 525 and 553 nm and red emission at 657 nm, while YVO₄:Yb³⁺,Tm³⁺ phosphors can generate blue emission at 476 nm, red emission at 648 nm, and near-infrared emission at 800 nm. Notably, YVO₄:Yb³⁺,Er³⁺,Tm³⁺ samples can exhibit green emission, blue emission, red emission, and near-infrared emission at the same time, which might endow the as-prepared samples with potential applications in many fields, such as luminous paint, infrared detection, and biological label.     

Optical spectra and excited state relaxation dynamics of Sm<Superscript>3+</Superscript> in Gd<Subscript>2</Subscript>SiO<Subscript>5</Subscript> single crystal

Single crystals of gadolinium orthosilicate Gd₂SiO₅ containing 0.5 at% and 5 at% of Sm³⁺ were grown by the Czochralski method. Optical absorption spectra, luminescence spectra and luminescence decay curves were recorded for these systems at 10 K and at room temperature. Comparison of optical spectra recorded in polarized light revealed that the anisotropy of this optically biaxial host affects the intensity distribution within absorption and emission bands related to transitions between multiplets rather than the overall band intensity. It has been found that among four bands of luminescence related to the ⁴G_5/2→⁶H_J (J=5/2–11/2) transitions of Sm³⁺ in the visible and near infrared region the ⁴G_5/2 →⁶H_7/2 one has the highest intensity with a peak emission cross section of 3.54×10⁻²¹ cm² at 601 nm for light polarized parallel to the crystallographic axis c of the crystal. The luminescence decay curve recorded for Gd₂SiO₅:0.5 at% Sm³⁺ follows a single exponential time dependence with a lifetime 1.74 ms, in good agreement with the ⁴G_5/2 radiative lifetime τ _rad=1.78 ms calculated in the framework of Judd-Ofelt theory. Considerably faster and non-exponential luminescence decay recorded for Gd₂SiO₅:5 at% Sm³⁺ sample was fitted to that predicted by the Inokuti-Hirayama theory yielding the microparameter of Sm³⁺–Sm³⁺ energy transfer C _da=1.264×10⁻⁵² cm⁶×s⁻¹.     

The effect of argon gas pressure on structural,morphological and photoluminescence properties of pulsed laser deposited KY<Subscript>3</Subscript>F<Subscript>10</Subscript>:Ho<Superscript>3+</Superscript> thin films

KY₃F₁₀:Ho³⁺ thin films were deposited by a pulsed laser deposition technique with Nd–YAG laser radiation (λ = 266 nm) on (100) silicon substrate. The XRD and FE-SEM results show improved crystalline structure for the film deposited at a pressure of 1 Torr. The AFM results show that the RMS roughness of the films increases with rise in argon gas pressure. The EDS elemental mapping shows Y-excess for all the films deposited under all pressures, and this is attributed to its higher mass and low volatility as compared to K and F. XPS analysis further confirmed Y-excess in the deposited films. Green PL emission at 540 nm was investigated at three main excitation wavelengths, namely 362, 416 and 454 nm. The PL emission peaks increase with rise in background argon gas pressure for all excitation wavelengths. The highest PL intensity occurred at excitation of 454 nm for all the thin films. In addition, faint red (near infrared) emission was observed at 750 nm for all the excitations. The green emission at 540 nm is ascribed to the ⁵F₄–⁵I₈ and ⁵S₂–⁵I₈ transitions, and the faint red emission at 750 nm is due to the ⁵F₄–⁵I₇ and ⁵S₂–⁵I₇ transitions of Ho³⁺.     

Synthesis and Optical Characterization of Red-Emitting BaTa<Subscript>2</Subscript>O<Subscript>6</Subscript>:Eu<Superscript>3+</Superscript> Phosphors

Undoped and Eu³⁺ doped BaTa₂O₆ phosphors were synthesized via solid state reaction method and characterized by using XRD, SEM-EDS and photoluminescence (PL) analyses. The XRD results revealed that the crystal structure of BaTa₂O₆ allowed up to 10 mol% levels of Eu³⁺ ions due to the TTB characteristic network of adjacent octahedrals. SEM-EDS analyses confirmed the formation of BaTa₂O₆ structure and EuTaO₄ secondary phase. BaTa₂O_6:Eu³⁺ phosphors exhibited orange and red emissions at 592.2 nm and 615.7 nm in the visible region respectively. The Commission Internationale d’Eclairage (CIE) chromaticity coordinates of the BaTa₂O_6:Eu³⁺ phosphors that excited at λ _ex = 400 nm ranged from orangish-red to pinkish-red depending on increasing Eu³⁺ concentration.     

Luminescence in Dy<Superscript>3+</Superscript> and Eu<Superscript>3+</Superscript> Activated K<Subscript>3</Subscript>Al<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

The Dy³⁺ and Eu³⁺ activated K₃Al₂ (PO₄)₃ phosphors were prepared by a combustion synthesis. From a powder X-ray diffraction (XRD) analysis the formation of K₃Al₂ (PO₄)₃ was confirmed. In the photoluminescence emission spectra, the K₃Al₂(PO₄)₃:Dy³⁺ phosphor emits two distinctive colors: blue and yellow whereas K₃Al₂(PO₄)₃:Eu³⁺ emits red color. Thus the combination of colors gives BYR (blue–yellow–red) emissions can produce white light. These phosphors exhibit a strong absorption between 340 and 400 nm which suggest that present phosphor is a promising candidate for producing white light-emitting diodes (LED).     

Intense White Luminescence from Combustion Synthesized Ca<Subscript>12</Subscript>Al<Subscript>14</Subscript>O<Subscript>33</Subscript>: Yb<Superscript>3+</Superscript>/Yb<Superscript>2+</Superscript> Single Phase Phosphor

The Ca₁₂Al₁₄O₃₃: Yb³⁺/Yb²⁺ single phase nano-phosphor has been synthesized through combustion route and its luminescence and lifetime studies have been carried out up to 20 K using 976 and 266 nm excitations. The samples heated in open atmosphere have shown the presence of Yb in Yb³⁺ and Yb²⁺ states. The 976 nm excitation results a cooperative upconversion emission at 486 nm due to the Yb³⁺ state and a broad band in the blue region and has been assigned to arise from the defect centers. The 266 nm excitation on the other hand results a broad emission band even from as-synthesized phosphor without doping of Yb, the width of which increases in presence of Yb due to the emission from Yb²⁺ ions formed in heated samples. The white emission covers almost whole visible region with bandwidth 190 nm. The ions in Yb²⁺ state has been found to increase with the increase in heating temperature up to 1,273 K. A back conversion of Yb²⁺ to Yb³⁺ has been observed for higher temperatures. Effect of boric and phosphoric acids as flux on the emission properties of Yb³⁺ and Yb²⁺ states have been examined and discussed. Quantum yield of emission has also been determined for different samples.     

Microstructural and Radioluminescence Characteristics of Nd<Superscript>3+</Superscript> Doped Columbite-Type SrNb<Subscript>2</Subscript>O<Subscript>6</Subscript> Phosphor

Undoped and different concentration Nd³⁺ doped SrNb₂O₆ powders with columbite structure were synthesized by molten salt process using a mixture of strontium nitrate and niobium (V) oxide and NaCl-KCl salt mixture as a flux under relatively low calcining temperature. X-ray diffraction analysis results indicated that SrNb₂O₆ phases found to be orthorhombic columbite single phase for undoped, 0.5 and 3 mol% Nd³⁺ doping concentrations. Phase composition of the powders was examined by SEM-EDS analyses. Radioluminescence properties of Nd³⁺ doped samples from UV to near-IR spectral region were studied. The emissions increased with the doping concentration of up to 3 mol%, and then decreased due to concentration quenching effect. There is a sharp emission peak around 880 nm associated with ⁴F_5/2 → ⁴I_9/2 transition in the Nd³⁺ ion between 300 and 1100 nm. The broad emission band intensity was observed from 400 to 650 nm where the peak intensities increased by increasing Nd³⁺ doping concentration. All the measurements were taken under the room temperature.     

On the Luminescence of Ce<Superscript>3+</Superscript>, Eu<Superscript>3+</Superscript>, and Tb<Superscript>3+</Superscript> in Novel Borate LiSr<Subscript>4</Subscript>(BO<Subscript>3</Subscript>)<Subscript>3</Subscript>

This paper reports on the photoluminescence (PL) and time-resolved properties of Ce³⁺, Eu³⁺, and Tb³⁺ in novel LiSr₄(BO₃)₃ powder phosphors. Ce³⁺ shows an emission band peaking at 420 nm under 350-nm UV excitation. Energy transfer from Ce³⁺ to Mn²⁺ takes place in the co-doped samples. Eu³⁺ shows red emission under near UV excitation. LiSr₄(BO₃)₃:Eu³⁺ phosphor could be a suitable candidate for phosphor-converted solid state lighting. The luminescence lifetime is 2.13 ms for Eu³⁺ in LiSr₄(BO₃)₃:0.001Eu³⁺. As Eu³⁺ concentration increasing, the decay curves deviate from exponential behavior. Tb³⁺ shows the strongest ⁵D₄→⁷ F₅ emission line at 540 nm. Decay curves of ⁵D₄→⁷ F₅ and ⁵D₃→⁷ F₅ emission with different Tb³⁺ concentrations were also measured. Cross-relaxation process is discussed based on the decay curves.     

Nanoparticles size effects in thermoluminescence of oxyfluoride glass-ceramics containing Sm<Superscript>3+</Superscript>-doped CaF<Subscript>2</Subscript> nanocrystals

Oxyfluoride glass-ceramic in the system SiO₂–Al₂O₃–CaF₂–SmF₃ containing Sm³⁺-doped CaF₂ nanocrystals in the range from 15 to 150 nm size were produced by using the controlled ceramization of the precursor glass. The incorporation of the Sm³⁺-dopant ion in the glass ceramic creates new electron-trapping centers and thermoluminescence (TL) method has been used in order to trace their evolution during glass ceramization. The 370 °C TL peak observed in precursor glass has been assigned to the recombination of the electrons released from the Sm²⁺-traps in the amorphous glass network. In the glass-ceramic sample containing nanocrystals with about 15 nm size the new weak TL peaks at 270, 290, and 310 °C were attributed to the recombination of the electrons released from the Sm²⁺-traps located mainly at the surface of the CaF₂ nanocrystals. In the glass-ceramic sample containing nanocrystals with about 150 nm size, the new TL peaks at 232, 270, and 302 °C size have been assigned to the recombination of the electrons released from the Sm²⁺-traps located inside the CaF₂ nanocrystals.     

Photon avalanche upconversion and pump power studies in LaF<Subscript>3</Subscript>:Er<Superscript>3+</Superscript>/Yb<Superscript>3+</Superscript> phosphor

Hexagonal LaF₃:Er³⁺/Yb³⁺ phosphor material has been synthesized by chemical precipitation method to obtain high near-infrared to green upconversion (UC) efficiency. Its thermal, structural and fluorescence properties have been studied. UC emission bands have been observed up to 315 nm in UV region. The effect of input pump power on the intensities of various emission bands has been studied in detail and photon avalanche UC mechanism has been identified. On increasing the excitation power, some bands have shown saturation in intensity. Also, at higher pump intensities two new UC bands were observed and their origin has been discussed. The phosphor has also been tested for possible UC-based fingerprint detection.     

A high efficient antireflective down-conversion Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Bi<Superscript>3+</Superscript>, Yb<Superscript>3+</Superscript> thin films

The high efficient antireflective down-conversion Y₂O₃:Bi, Yb films have been prepared successfully on Si(100) substrates by pulsed laser deposition (PLD) method, Upon excitation of ultraviolet photon varying from 300 to 400 nm, near-infrared emission of Yb³⁺ was observed for the film, can be efficiently absorbed by silicon (Si) solar cell. Most interestingly, there is a very low average reflectivity 1.46% for the incident light from 300 to 1100 nm. To the best of our knowledge, this is the lowest reflectance for the down-conversion thin films prepared by cost efficient method. The surface topography of the high efficient antireflective films can be controllably tuned through the substrate template regulation by optimizing process parameters. Besides, the results showed that there is a close relationship between luminescent property and morphology of the film. With the change of the surface morphology, the intensity of Bi³⁺ and Yb³⁺ emission peaks increase first and then decrease. The obtained results demonstrate that this film can enhance the Si solar cell efficiency through light trapping and spectrum shifting.     

Preparation and characterization of Sm<Superscript>3+</Superscript>-doped SrSnO<Subscript>3</Subscript> and its photoelectric performance as photo-anode of dye-sensitized solar cells

Sm³⁺-doped SrSnO₃ (SrSnO₃:Sm³⁺) nanopowders were synthesized by a simple hydrothermal method and followed by a heat treatment process. The as-synthesized nanopowders were assembled in dye-sensitized solar cells (DSSCs) to investigate their photoelectric properties. X-ray diffraction (XRD), scanning electron microscope (SEM), and energy-dispersive spectrometer (EDS) confirmed the formation of SrSnO₃:Sm³⁺ nanopowders with perovskite structure. The ultraviolet-visible absorption spectra and photoluminescence spectra indicate a down-conversion from ultraviolet light to visible light which matches the strong absorption region of the N719 dye. The DSSC based on SrSnO₃:Sm³⁺ photo-anode improved its photoelectric conversion efficiency (η) via the down-conversion of doped Sm³⁺. Under the irradiation of the simulated sunlight with 100 mW/cm², the DSSC based on SrSnO₃ doping with Sm³⁺ of 0.6 wt% showed the highest η of 1.54%, which improved 71.11% compared with the DSSC based on pure SrSnO₃.

Open image in new window

Graphical abstract Excitation and emission spectrums of SrSnO₃ with different Sm³⁺ doping amounts.

     

A novel white light-emitting diode (w-LED) fabricated with Sr<Subscript>6</Subscript>BP<Subscript>5</Subscript>O<Subscript>20</Subscript>:Eu<Superscript>2+</Superscript> phosphor

Sr₆BP₅O₂₀:Eu²⁺ phosphor was prepared by the solid-state reaction method under a weak reductive atmosphere and the photoluminescence properties were studied systematically. The bluish-green emission band of Sr₆BP₅O₂₀:Eu²⁺ phosphor is peaking at 475 nm, and the excitation bands are broad with peaks at about 290 and 365 nm with a shoulder around 390 nm, respectively. By combining with Ga(In)N-based near-ultraviolet LEDs, a bluish-green LED was fabricated based on the Sr₆BP₅O₂₀:Eu²⁺ phosphor, and a novel intense white LED was fabricated based on the bluish-green phosphor Sr₆BP₅O₂₀:Eu²⁺ and the red phosphor (Sr,Ca)₅(PO₄)₃Cl:Eu²⁺,Mn²⁺. When this two-phosphor white LED is operated under 20-mA forward-bias current at room temperature, the Commission Internationale de l’Eclairage(CIE) chromaticity coordinates (x,y), the correlated color temperature Tc, and the color rendering index Ra are calculated to be (0.3281,0.3071), 5687 K, and 87.3, respectively. The dependence of the bluish-green and two-phosphor white LEDs on different forward-bias currents from 5 mA to 50 mA shows a similar behavior. As the current increases, the relative intensity simultaneously increases. The CIE chromaticity coordinates (x,y) of the two-phosphor white LED tend to decrease. Consequently, the correlated color temperature Tc increases from 3800 K to 9400 K and the color rendering index Ra of the two-phosphor white LED increases from 83.4 to 91.8 simultaneously. PACS 07.60.-j; 42.70.-a; 71.55.Eq     

The upconversion luminescence and magnetism in Yb<Superscript>3+</Superscript>/Ho<Superscript>3+</Superscript> co-doped LaF<Subscript>3</Subscript> nanocrystals for potential bimodal imaging

Biocompatible upconversion nanoparticles with multifunctional properties can serve as potential nanoprobes for multimodal imaging. Herein, we report an upconversion nanocrystal based on lanthanum fluoride which is developed to address the imaging modalities, upconversion luminescence imaging and magnetic resonance imaging (MRI). Lanthanide ions (Yb³⁺ and Ho³⁺) doped LaF₃ nanocrystals (LaF₃ Yb³⁺/Ho³⁺) are fabricated through a rapid microwave-assisted synthesis. The hexagonal phase LaF₃ nanocrystals exhibit nearly spherical morphology with average diameter of 9.8 nm. The inductively coupled plasma mass spectrometry (ICP-MS) analysis estimated the doping concentration of Yb³⁺ and Ho³⁺ as 3.99 and 0.41%, respectively. The nanocrystals show upconversion luminescence when irradiated with near-infrared (NIR) photons of wavelength 980 nm. The emission spectrum consists of bands centred at 542, 645 and 658 nm. The stronger green emission at 542 nm and the weak red emissions at 645 and 658 nm are assigned to ⁵S₂ → ⁵I₈ and ⁵F₅ → ⁵I₈ transitions of Ho³⁺, respectively. The pump power dependence of luminescence intensity confirmed the two-photon upconversion process. The nanocrystals exhibit paramagnetism due to the presence of lanthanide ion dopant Ho³⁺ and the magnetization is 19.81 emu/g at room temperature. The nanocrystals exhibit a longitudinal relaxivity (r ₁) of 0.12 s^?1 mM^?1 and transverse relaxivity (r ₂) of 28.18 s^?1 mM^?1, which makes the system suitable for developing T2 MRI contrast agents based on holmium. The LaF₃ Yb³⁺/Ho³⁺ nanocrystals are surface modified by PEGylation to improve biocompatibility and enhance further functionalisation. The PEGylated nanocrystals are found to be non-toxic up to 50 μg/mL for 48 h of incubation, which is confirmed by the MTT assay as well as morphological studies in HeLa cells. The upconversion luminescence and magnetism together with biocompatibility enables the adaptability of the present system as a nanoprobe for potential bimodal imaging.     

Red,Yellow, Blue and Green Emission from Eu<Superscript>3+</Superscript>, Dy<Superscript>3+</Superscript> and Bi<Superscript>3+</Superscript> Doped Y<Subscript>2</Subscript>O<Subscript>3</Subscript>nano-Phosphors

Rare earth elements (RE = Eu³⁺& Dy³⁺)and Bi³⁺ doped Y₂O₃ nanoparticles were synthesized by urea hydrolysis method in ethylene glycol, which acts as reaction medium as well as a capping agent, at a low temperature of 140 °C,followed by calcination of the obtained product. Transmission electron microscope (TEM) images reveals that ovoid shaped Y₂O₃ nanoparticles of around 22–24 nm size range were obtained in this method. The respective RE and Bi³⁺ doped Y₂O₃ precursor nanoparticles when heated at 600 and 750 °C, retains the same shape as that of the as-synthesized Y₂O₃ precursor samples. From EDAX spectra, the incorporation of RE ions into the host has been studied. XRD pattern reveals the crystalline nature of the heated nanoparticles and indicate the absence of any impurity phase other than cubic Y₂O₃.However, the as-synthesized nanoparticles were highly amorphous without the presence of any sharp XRD peaks. Photoluminescence study suggests that the synthesized samples could be used as red (Eu³⁺), yellow (Dy³⁺), blue and green (Bi³⁺)emitting phosphors.     

Growth and optical properties of Pr<Superscript>3+</Superscript>:KLu(WO<Subscript>4</Subscript>)<Subscript>2</Subscript> laser crystal: a candidate for red emission laser

A Pr³⁺:KLu(WO₄)₂ crystal with dimension of 30 × 30 × 15 mm³ was grown in the K₂W₂O₇ flux. A slice was cut from the crystal, and the polarized absorption and fluorescence spectra were measured at room temperature. Based on the J-O theory, the oscillator intensity parameters Ω _t (t = 2, 4, 6), spontaneous emission probabilities and branch ratios were estimated and good results had been obtained. Furthermore, the crystal has a relatively large emission cross-section in the region of 615–630 nm with the highest value of 14.5 × 10^?20 cm², which indicates that the crystal is good for the application in red emission laser. The emission decay time for ¹D₂ and ³P₀ multiplets was discussed. By adapting the I-H model to fit the emission decay curves, the lifetime for ¹D₂ at 607 nm and ³P₀ at 615 nm are 19.72 μs and 8.95 μs, respectively. Then the corresponding fluorescence quantum efficiencies of the two multiplets reach 83.7 % and 87.9 %, respectively. All the studies illustrate that this crystal is potential in red emission laser application.