Study on the surface properties of wood/polyethylene composites treated under plasma

Wood/polyethylene (PE) composites are widely used in many fields for its excellent properties, but they are hard to adhere for the surface lacking of polarity. So low-pressure glow discharge of air plasma was used to improve the adhesion properties of wood/PE composites. The composites were treated by plasma under different discharge power. And the changes on the surface properties of the treated and untreated composites were studied by contact angle, Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS) analysis. The measurement showed that the contact angle decreased after plasma treatment, and the contact angle decreased gradually with the increasing of discharge power. The FTIR analysis results showed that the polar groups such as hydroxyl, carbonyl and carboxyl were formed on the surface of the composites treated under plasma. SEM and AFM results showed that the roughness of plasma treated samples increased. XPS analysis results indicated that the content of carbon element decreased while the content of oxygen element in the composition of wood/PE composites surface element increased and it reached a balance in a higher power, meanwhile a lot of carboxyl groups were formed. The newly formed polar groups are benefit for the adhesion of composites. The shear bonding strength test showed that the adhesion properties of wood/PE composites improved effectively after plasma treatment.     

Surface modification of fluorosilicone acrylate RGP contact lens via low-temperature argon plasma

A fluorosilicone acrylate rigid gas permeable (RGP) contact lens was modified via argon plasma to improve surface hydrophilicity and resistance to protein deposition. The influence of plasma treatment on surface chemical structure, hydrophilicity and morphology of RGP lens was investigated by X-ray photoelectron spectrometer (XPS), contact angle measurements and scanning electron microscope (SEM), respectively. The contact angle results showed that the hydrophilicity of the contact lens was improved after plasma treatment. XPS results indicated that the incorporation of oxygen-containing groups on surface and the transformation of silicone into hydrophilic silicate after plasma treatment are the main reasons for the surface hydrophilicity improvement. SEM results showed that argon plasma with higher power could lead to surface etching.     

Modification of surface properties of polypropylene (PP) film using DC glow discharge air plasma

The industrial use of polypropylene (PP) films is limited because of undesirable properties such as poor adhesion and printability. In the present study, a DC glow discharge plasma has been used to improve the surface properties of PP films and make it useful for technical applications. The change in hydrophilicity of modified PP film surface was investigated by contact angle (CA) and surface energy measurements as a function of exposure time. In addition, plasma-treated PP films have been subjected to an ageing process to determine the durability of the plasma treatment. Changes in morphological and chemical composition of PP films were analyzed by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The improvement in adhesion was studied by measuring T-peel and lap shear strength. The results show that the surface hydrophilicity has been improved due to the increase in the roughness and the introduction of oxygen-containing polar groups. The AFM observation on PP film shows that the roughness of the surface increased due to plasma treatment. Analysis of chemical binding states and surface chemical composition by XPS showed an increase in the formation of polar functional groups and the concentration of oxygen content on the plasma-processed PP film surfaces. T-peel and lap shear test for adhesion strength measurement showed that the adhesion strength of the plasma-modified PP films increased compared with untreated films surface.     

Polytetrafluoroethylene surface modification by filamentary and homogeneous dielectric barrier discharges in air

In this paper, polytetrafluoroethylene (PTFE) films are modified using non-equilibrium plasma generated by homogeneous DBD in air at medium pressure, and the results are compared to those treated by using filamentary DBD in air at atmospheric pressure. The surface properties of PTFE films before and after the treatments are studied using contact angle and surface energy measurement, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). It is found that the plasma treatments modify the PTFE surface in both morphology and composition. The PTFE films modified in both treatments show a remarkable decrease in water contact and a remarkable increase in surface energy. XPS analysis reveals that oxygen-containing polar groups are introduced onto the PTFE surface, and SEM analysis shows that the surfaces of the films are etched after both the treatments. It is found that homogeneous DBD is more effective in PTFE surface modification than filamentary DBD as it can make the contact angle decline to a lower level by introducing more oxygen-containing groups, and the possible reason for this effect is discussed.     

Surface modification of porous poly(tetrafluoroethylene) film via cold plasma treatment

In this study, cold plasma technology was applied for the surface modification of porous polytetrafluoroethylene (PTFE) film to improve the hydrophilicity. The surface properties of PTFE, modified by air, helium (He) or acrylic acid (AAc), were investigated with scanning electron microscopy (SEM), scanning probe microscope (SPM), in situ X-ray photoelectron spectroscopy (XPS) and water contact angle measurements. The changes of the surface property before and after plasma treatment were discussed. According to SEM and SPM measurements, the surface roughness increased at different levels after plasma treatment. Compared to air and AAc plasma treatment, the He plasma treatment introduced large amounts of oxygen into the surface, as known from XPS results. Contact angle measurements revealed that the hydrophilicity of the PTFE film surface was greatly improved due to the surface roughness and changes of chemical elements on the PTFE surface.     

Study on hydrophilicity of polymer surfaces improved by plasma treatment

Surface properties of polycarbonate (PC), polypropylene (PP), polyethylene terephthalate (PET) samples treated by microwave-induced argon plasma have been studied with contact angle measurement, X-ray photoelectron spectroscopy (XPS) and scanned electron microscopy (SEM). It is found that plasma treatment modified the surfaces both in composition and roughness. Modification of composition makes polymer surfaces tend to be highly hydrophilic, which mainly depended on the increase of ratio of oxygen-containing group as same as other papers reported. And this experiment further revealed that CO bond is the key factor to the improvement of the hydrophilicity of polymer surfaces. Our SEM observation on PET shown that the roughness of the surface has also been improved in micron scale and it has influence on the surface hydrophilicity.     

交流和纳秒脉冲Ar/H2O介质阻挡放电聚丙烯材料表面亲水改性对比研究

为了提高等离子体对聚合物材料表面处理的应用效果,优化亲水处理的条件,研究了交流和纳秒脉冲氩气介质阻挡放电（DBD）中添加适量H₂O,对聚丙烯（PP）亲水改性的处理效果。利用电学和光学诊断方法,系统地对比了交流DBD和纳秒脉冲DBD的放电特性,结果表明,纳秒电源驱动DBD具有更高的放电瞬时功率,更好的放电均匀性和更高的能量效率。通过测量不同水蒸气含量下DBD的OH发射光谱强度,确定了PP材料亲水性处理中H₂O添加的最优含量。利用交流和纳秒脉冲电源驱动DBD分别对PP材料进行亲水改性的处理,测量了不同条件下改性处理后的表面水接触角,并利用原子力显微镜（AFM）和傅里叶红外光谱（FTIR）分别对处理前后PP材料的表面物理形貌和表面化学成分进行分析。结果发现,经DBD处理后PP材料的水接触角明显降低,表面粗糙度明显增大,表面的亲水性含氧基团,羟基（?OH）和羰基（C=O）的数量大幅增加。相比交流电源,纳秒脉冲DBD处理的改性效果更好,其处理后的材料表面水接触角,比交流DBD处理的低5°左右,表面粗糙度也有所提升。而水蒸气的加入可使PP材料的表面水接触角进一步减小4°左右,表面粗糙度明显提升。研究结果为优化DBD聚合物材料表面改性实验条件及处理的效果提供了重要的参考依据。     

Influence of argon plasma treatment on polyethersulphone surface

Polyethersulphone (PES) was modified to improve the hydrophilicity of its surface, which in turn helps in improving its adhesive property. The modified PES surface was characterized by contact angle measurement, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and Vicker’s microhardness measurement. The contact angles of the modified PES reduces from 49° to 10° for water. The surface free energy (SFE) calculated from measured contact angles increases from 66.3 to 79.5 mJ/m² with the increase in plasma treatment time. The increase in SFE after plasma treatment is attributed to the functionalization of the polymer surface with hydrophilic groups. The XPS analysis shows that the ratio of O/C increases from 0.177 to 0.277 for modified PES polymer. AFM shows that the average surface roughness increases from 6.9 nm to 23.7 nm due to the increase in plasma treatment time. The microhardness of the film also increases with plasma treatment.     

Surface chemistry of atmospheric plasma modified polycarbonate substrates

Surface of polycarbonate substrates were activated by atmospheric plasma torch using different gas pressure, distance from the substrates, velocity of the torch and number of treatments. The modifications were analyzed by contact angle measurements, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and UV-vis spectrophotometry. Plasma treatment caused the surface characteristics to become more hydrophilic as measured by the water contact angle, which decreased from 88° to 18°. The decrease in contact angle was mainly due to oxidation of the surface groups, leading to formation of polar groups with hydrophilic property. XPS results showed an increase in the intensity of -(C-O)- groups and also introduction of new functional groups i.e. -(O-CO)- after the treatment process. AFM topographic images demonstrated an increase in the rms roughness of the surface from 2.0 nm to 4.0 nm caused by the treatment. Increase in rms roughness of the surface caused relevant decrease in transmission up to ∼2-5%.     

Polypropylene modified with 2-hydroxyethyl acrylate-g-2-methacryloyloxyethyl phosphorycholine and its hemocompatibility

Polypropylene (PP) was modified with 2-hydroxyethyl acrylate (HEA) by solution radical grafting to introduce active hydroxyl groups on polypropylene backbone (PP-g-HEA). Then the biomimic monomer, 2-methacryloyloxyethyl phosphorycholine (MPC), was grafted onto the surface of PP-g-HEA film (PP-g-HEA-g-MPC) by redox graft polymerizations with ceric(IV) ammonium nitrate as an initiator. Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) showed that the HEA and MPC were introduced onto PP molecular chains and the copolymer, PP-g-HEA-g-MPC were formed. The water contact angle measurements demonstrated that the final modified PP film exhibited a better hydrophilic surface compared to the neat PP film. The platelets adhesion on the neat PP, PP-g-HEA and PP-g-HEA-g-MPC film was examined by scanning electron microscopy (SEM). It was found that a large number of platelets were adhered and activated on the surface of neat PP and PP-g-HEA films, while the number of platelets on PP-g-HEA-g-MPC surface was decreased remarkably. The result revealed that the introduction of poly(MPC) onto the PP surface improved the hemocompatibility of PP substantially.     

Modification of surface properties of polyamide 6 films with atmospheric pressure plasma

To investigate the effect of the different plasma gases treatment on the surface modification of atmospheric pressure plasma, polyamide 6 films were treated using pure helium (He), He/O₂ and He/CF₄, respectively. Atomic force microscopy (AFM) showed rougher surface, while X-ray photoelectron spectroscopy (XPS) revealed increased oxygen and fluorine contents after the plasma treatments. The plasma treated samples had lower water contact angles and higher T-peel strength than that of the control. The addition of small amount of O₂ or CF₄ to He plasma increases the effectiveness of the plasma treatment in polymer surface modification in terms of surface roughness, surface hydrophilic groups, etching rate, water contact angle and bonding strength.     

Surface analysis of oxygen plasma treated poly(p-phenylene benzobisoxazole) fibers

The influence of oxygen plasma treatment on surface properties of poly(p-phenylene benzobisoxazole) (PBO) fibers and aging effect of the oxygen plasma modified PBO fiber surfaces were investigated by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and dynamic contact angle analysis (DCAA), respectively. The results indicated that the oxygen plasma treatment introduced some polar groups to PBO fiber surfaces, enhanced surface roughness and changed surface morphologies of PBO fibers by plasma etching and oxidative reactions. Surface wettability of PBO fibers may be significantly improved by increasing surface free energy of the fibers via oxygen plasma treatment. Aging effect of the oxygen plasma treated PBO fibers showed that the fiber surface wettability degraded in the first several days after the plasma treatment, and it was found to be changeless as the aging time continued as long as 30 days.     

Surface characterization of polyethylene terephthalate/silica nanocomposites

Poly(ethylene terephthalate) (PET) based nanocomposites containing hydrophilic (i.e. Aerosil 200 or Aerosil TT 600) or hydrophobic (i.e. Aerosil R 972) nano-silica were prepared by melt compounding. Influence of nano-silica type on surface properties of the resultant nanocomposites was investigated by the use of Fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM), contact angle measurement (CAM), scanning electron microscopy (SEM) and reflectance spectroscopy (RS). The possible interaction between nano-silica particles and PET functional groups at bulk and surface were elucidated by transmission FTIR and FTIR-ATR spectroscopy, respectively. AFM studies of the resultant nanocomposites showed increased surface roughness compared to pure PET. Contact angle measurements of the resultant PET composites demonstrated that the wettability of such composites depends on surface treatment of the particular nano-silica particles used. SEM images illustrated that hydrophilic nano-silica particles tended to migrate to the surface of the PET matrix.     

Three different low-temperature plasma-based methods for hydrophilicity improvement of polyethylene films at atmospheric pressure

Three different low-temperature plasma-based methods were used to improve the surface hydrophilicity of polyethy- lene （PE） films, and all the modification processes were carried out by employing an atmospheric pressure plasma jet （APPJ） system. （a） PE films were directly modified by APPJ using a gas mixture of He and 02. （b） Acrylic acid （AA） was introduced into the system and a polymer acrylic acid （PAA） coating was deposited onto the PE films. （c） AA was grafted onto the PE surface activated by plasma pre-treatment. It was found that the hydrophilicity of the PE films was significantly improved for all the three methods. However, the samples modified by Process （a） showed hydrophobicity recovery after a storage time of 20 days while no significant change was found in samples modified by Process （b） and Process （c）. The Fourier transform infrared spectroscopy （FTIR） results indicated that the most intensive C=O peak was detected on the PE surface modified by Process （c）. According to the X-ray photoelectron spectroscopy （XPS） analysis, the ratios of oxygen-containing polar groups for samples modified by Process （b） and Process （c） were higher than that modified by Process （a）.     

Effects of O2 and H2O plasma immersion ion implantation on surface chemical composition and surface energy of poly vinyl chloride

Oxygen and water plasma immersion ion implantation (PIII) was used to modify poly vinyl chloride (PVC) to enhance oxygen-containing surface functional groups for more effective grafting. The modified surfaces were characterized by X-ray photoelectron spectroscopy (XPS), attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and contact angle measurements. Our experimental results show that both oxygen and water PIII can greatly improve the O to C ratios on the surface. The optimal plasma processing conditions differ for the two treatments. The hydrophilicity and surface energy of the plasma-implanted PVC are also improved significantly. Our results indicate that O₂ and H₂O PIII increase both the polar and dispersion interactions and consequently the surface energy. It can be explained by the large amount of oxygen introduced to the surface and that many CC bonds are transformed into more polar oxygen containing functional groups.     

Formation of a high hydrophilic/hydrophobic contrast surface on PET substrates by ECR generated sulfur hexafluoride plasma

High hydrophilic/hydrophobic contrast surfaces on polyethylene terephthalate (PET) substrates were formed by shadow mask technique in electron cyclotron resonance generated sulfur hexafluoride plasma atmosphere. The X-ray photoelectron spectroscopy (XPS) analyses indicate that the unmasked PET surfaces contained a high proportion of the CF₂-CF₂ groups, and therefore were hydrophobic with large water contact angle. However, the surface wettability was found to increase drastically on the masked PET surfaces. This could be resulted from a mass of COF (acid fluoride) compounds observed by XPS on the masked film surfaces. The COF compounds could react with atmospheric moisture to form -COOH groups, which in turn increased the surface wettability. In addition, the surface wetting property of the masked areas was found to change significantly with the plasma treatment time, the mask-to-substrate distance and the storage time after the treatment. The best contract in water contact angle obtained from the treated PET samples was larger than 100° after 168 h of storage.     

Femtosecond laser-induced surface wettability modification of polystyrene surface

In this paper, we demonstrated a simple method to create either a hydrophilic or hydrophobic surface. With femtosecond laser irradiation at different laser parameters, the water contact angle (WCA) on polystyrene’s surface can be modified to either 12.7° or 156.2° from its original WCA of 88.2°. With properly spaced micro-pits created, the surface became hydrophilic probably due to the spread of the water droplets into the micro-pits. While with properly spaced micro-grooves created, the surface became rough and more hydrophobic. We investigated the effect of laser parameters on WCAs and analyzed the laser-treated surface roughness, profiles and chemical bonds by surface profilometer, scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). For the laser-treated surface with low roughness, the polar (such as C—O, C=O, and O—C=O bonds) and non-polar (such as C—C or C—H bonds) groups were found to be responsible for the wettability changes. While for a rough surface, the surface roughness or the surface topography structure played a more significant role in the changes of the surface WCA. The mechanisms involved in the laser surface wettability modification process were discussed.     

Surface modification of polypropylene and compatibilization of interfaces in incompatible blends of polypropylene with polystyrene by plasma of CO2

The effect of surface modification of polypropylene (PP) film is induced by CO₂ plasma in this study. The change in chemical structures on the surface of PP film is characterized by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FT-IR). The polarity of modified surface of PP film is investigated by contact angle method. The compatibilization of interfaces between polypropylene and polystyrene phases in incompatible blends is studied by the treatment of plasma of CO₂. Transition layer thickness is measured by small angle light scattering (SALS).     

Surface modification of the nanoparticles by an atmospheric room-temperature plasma fluidized bed

Using hexamethyldisiloxane (HMDSO) monomer, the magnetic nanoparticles (NPs) of nickel oxide (NiO) were modified by using an atmospheric room-temperature plasma fluidized bed (ARPFB). The plasma gas temperature of the ARPFB was not higher than 325 K, which was favorable for organic polymerization. The plasma optical emission spectrum (OES) of the gas mixture consisting of argon (Ar) and HMDSO was recorded by a UV-visible monochromator. The as-treated NPs were characterized by means of scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The results show that the assembling NPs were isolated greatly after modified by the organosilicon polymer. Moreover, this treatment process changed the wettability of the NPs from super-hydrophilicity to super-hydrophobicity, and the contact angle (CA) of water on the modified NPs surface exceeded 150°. Therefore, the ARPFB is a prospective technology for the NPs surface modification according to the different requirements.     

Surface modification of a polyamide 6 film by He/CF4 plasma using atmospheric pressure plasma jet

Polyamide 6 (PA 6) films are treated with helium(He)/CF₄ plasma at atmospheric pressure. The samples are treated at different treatment times. The surface modification of the PA 6 films is evaluated by water contact angle, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The etching rate is used to study the etching effect of He/CF₄ plasma on the PA 6 films. The T-peel strengths of the control and plasma treated films are measured to show the surface adhesion properties of the films. As the treatment time increases, the etching rate decreases steadily, the contact angle decreases initially and then increases, while the T-peel strength increases first and then decreases. AFM analyses show that the surface roughness increases after the plasma treatment. XPS analyses reveal substantial incorporation of fluorine and/or oxygen atoms to the polymer chains on the film surfaces.