Molecular dynamics investigation of deposition and annealing behaviors of Cu atoms onto Cu(0 0 1) substrate

The deposition growth and annealing behaviors of Cu atoms onto Cu(0 0 1) are investigated in atomic scale by molecular dynamics (MD) simulation. The results indicate that the film grows approximately in a layer-island mode as the incident energy is from 1 to 5 eV, while surface intermixing can be significantly observed at 10 eV. The surface roughness of the film decreases with increasing the incident energy, and the film after annealing becomes smoother and more ordered. These phenomena may be attributed to the enhanced atomic mobility for higher incident energy and thermal annealing. It also indicates that atomic mixing is more significant with increasing both the incident energy and substrate temperature. In addition, the peak-to-peak distances of radial distribution function (RDF) clearly indicate that the films before and after annealing are still fcc structure except for that at the melting temperature of 1375.6 K. After annealing, the film at the melting temperature returns to fcc structure instead of amorphous. Moreover, the residual stress and Poisson ratio of the film are remarkably affected by the thermal annealing. Furthermore, the density of thin film is obviously affected by the substrate temperature and annealing process. Therefore, one can conclude that high incident energy, substrate temperature and thermal annealing could help to enhance the surface morphology and promote the microstructure of the film.     

Atomic-level investigation of Al and Ni thin film growth on Ni(1 1 1) surface: Molecular dynamics simulation

Using molecular dynamics (MD) simulation, the structural characteristics of Al and Ni thin film growth on Ni(1 1 1) substrate according to the incident energy of adatoms were investigated. In case of Al on Ni(1 1 1), Al adatoms were grown basically through the layer-by-layer growth mode. On the other hand, Ni thin films on Ni(1 1 1) surface at low incident energy were shown to favor island growth. The steering effect due to atomic attraction, which results in rougher surface, was significantly observed at low incident energy. The growth mode of Ni film was, however, changed to follow layer-by-layer growth mode for the incident energy of 6 eV. The different aspects of surface morphology between Al and Ni deposition on Ni(1 1 1) surface could be successfully explained by the surface diffusion and impact cascade diffusion.     

Use of the direct negative Cu ion beam deposition for the control of the properties of Cu thin film

Direct metal ion beam deposition (DMIBD) technique for Cu thin film metallization is characterized. With suitable operating conditions, secondary Cu⁻ ion yield, ion/atom arrival rate ratio, ion beam energy spreads were optimized at 15%, 0.3, and 10%, respectively.After optimization of DMIBD system, the effect of Cu ion beam energy on the resistivity, adhesion strength, and surface morphology of Cu thin film was investigated. TEM micrograph shows that the film prepared at 75 eV was polycrystalline, while the film prepared at 0 eV was vertical columnar structure.As ion beam energy is increased from 25 to 75 eV, the resistivity is decreased from 6.21 to 2.09 μΩ cm, while the critical load to cause adhesion failure was increased to about 13 N at 200 eV, which is four-times higher that that of 25 eV.     

The influences of the local impact site and incident energy on the transport behaviors of single copper atom onto Cu (0 0 1) surface

Molecular dynamics (MD) simulation is carried out to study the transport behaviors of a single deposited atom in Cu film homoepitaxy. We consider the normal Cu incident atoms impinging on the Cu (0 0 1) surface at four possible local impact sites (top, bridge, hollow and general). The observed transport behaviors of the deposited atom onto the surface include: direct adsorption (DA), penetration by atomic exchange, and transient penetration (TP), which a deposited atom penetrates the interstitial site and then rapidly migrates to a stable site on the surface. The results show that transport behaviors of the deposited atom are closely related to both the local impact site and the incident energy. The maximum increment of kinetic energy at every impact site approaches to a certain value except for the incident energy below 2.0 eV. Furthermore, as the incident energy is higher than the penetration threshold, TP behavior could be observed again in some energy ranges. This interesting phenomenon, which cannot be explained by the existing theories, is possibly attributed to the dynamical competition between the deposited atom and substrate atoms.     

Thin films of molecular materials synthesized from C32H20N10M (M = Co, Pb, Fe): Film formation, electrical and optical properties

In this work, the synthesis of molecular materials formed from metallic phthalocyanines and 1,4-phenylenediamine is reported. The powder and thin film (∼80-115 nm thickness) samples of the synthesized materials, deposited by vacuum thermal evaporation, show the same intra-molecular bonds in the IR spectroscopy studies, which suggests that the thermal evaporation process does not alter these bonds. The morphology of the deposited films was studied using scanning electron microscopy (SEM) and atomic force microscopy (AFM) and their optical and electrical properties were studied as well. The optical parameters have been investigated using spectrophotometric measurements of transmittance in the wavelength range 200-1200 nm. The absorption spectra recorded in the UV-vis region for the deposited samples showed two bands, namely the Q and Soret bands. The optical activation energy was calculated and found to be 3.41 eV for the material with cobalt, 3.34 eV for the material including lead and 3.5 eV for the material with iron. The effect of temperature on conductivity was measured for the thin films and the corresponding conduction processes are discussed in this work.     

Molecular dynamics and experimental studies on deposition mechanisms of ion beam sputtering

Molecular dynamics (MD) simulation and experimental methods are used to study the deposition mechanism of ionic beam sputtering (IBS), including the effects of incident energy, incident angle and deposition temperature on the growth process of nickel nanofilms. According to the simulation, the results showed that increasing the temperature of substrate decreases the surface roughness, average grain size and density. Increasing the incident angle increases the surface roughness and the average grain size of thin film, while decreasing its density. In addition, increasing the incident energy decreases the surface roughness and the average grain size of thin film, while increasing its density. For the cases of simulation, with the substrate temperature of 500 K, normal incident angle and 14.6 × 10⁻¹⁷ J are appropriate, in order to obtain a smoother surface, a small grain size and a higher density of thin film. From the experimental results, the surface roughness of thin film deposited on the substrates of Si(1 0 0) and indium tin oxide (ITO) decreases with the increasing sputtering power, while the thickness of thin film shows an approximately linear increase with the increase of sputtering power.     

Effects of post-thermal treatments on morphological and optical properties of NiO/Ni(OH)2 thin films synthesized by solution growth

Room temperature deposition of PVP capped nanostructured NiO/Ni(OH)₂ thin film, the morphological and optical characterizations by solution growth technique are reported. The nanostructured thin films which were deposited on optical glass substrates were annealed at different temperatures and then subjected to structural, morphological and optical characterizations. X-ray diffraction measurements of the films revealed that higher temperatures during the thermal treatment enhanced the crystallinity of the thin films. The SEM surface micrographs show non-interconnected uniformly deposited fibre-like structures with approximate lengths between 400 and 1200 nm. The optical band gap energy roughly decreased from about 2.7 eV to about 2.2 eV with thermal treatment. The absorbance of the thin films annealed at 300 and 400 °C was as high as 90% in the visible region of the electromagnetic spectrum. These materials could be useful in solar thermal conversion processes.     

Epitaxial growth of Al on Si(1 1 1) with Cu buffer layers

The structure of thin Al films grown on Si(1 1 1) with thin Cu buffer layers has been investigated using synchrotron radiation photoemission spectroscopy. A thin Cu(1 1 1) layer between the Si(1 1 1) substrate and an Al film may enhance quantum well effects in the Al film significantly. The strength of quantum well effects has been investigated qualitatively with respect to the thickness of the Cu buffer layer and to the Al film thickness. Deposition of Cu on Si(1 1 1)7 × 7 leads to formation of a disordered silicide layer in an initial regime before a well-ordered Cu(1 1 1) film is formed after deposition of the equivalent of 6 layers of Cu. In the regime below 6 layers of Cu the disorder is transferred to Al layers subsequently grown on top. The initial growth of up to 8 layers of Al on a well-ordered Si/Cu(1 1 1) layer leads to a disordered film due to the lattice mismatch between the two metals. When the Cu buffer layer and the Al over-layer are above 6 and 8 layers, respectively the Al film shows sharp low energy electron diffraction patterns and very sharp quantum well peaks in the valence band spectra signalling good epitaxial growth.     

Synthesis of Cadmium Selenide thin films at low-temperature by simple Chemical route and their Characterization

Crystalline CdSe thin film has been deposited using appropriate precursor solution containing cadmium sulfate octahydrate, tartaric acid, potassium hydroxide, ammonia and sodium selenosulfate. The effect of parameters such as bath composition, deposition temperature, pH of the solution, speed of the rotation and the specificity of complexing agent on growth process is studied. The ‘as-deposited’ CdSe thin film was found to be red in color, specularly reflective and well adherent to the glass substrate. The crystalline phase of the deposited sample was hexagonal wurtzite-type. The analysis of optical absorption data shows energy band gap energy (E_g) 2.01 eV. The morphological study and compositional analysis of film sample have been discussed. The electrical resistivity of CdSe thin film was found to the order of 10⁶ Ω cm.     

Investigation of induced parallel magnetic anisotropy at low deposition temperature in Ba-hexaferrites thin films

In this paper we present the effect of low substrate temperature on structural, morphological, magnetic and optical properties of Ba-hexaferrite thin films. Films were deposited on single crystal Silicon (1 0 0) substrate employing the Pulsed Laser Deposition (PLD) technique. The structural, morphological, magnetic and optical properties are found to be strongly dependent on substrate temperature. The low substrate temperatures (room temperature to 200 °C) restrict the formation of larger grains. For the higher substrate temperature i.e., 400 °C, the grain size of the deposited thin film are much larger. The film grown at low substrate temperature do not show any anisotropy. As the substrate temperature is increased, the easy axis of the films alinged itself in the direction parallel to the film plane whereas the hard axis remained in the perpendicular direction. The higher substrate temperature caused the uniaxial magnetic anisotropy, which is very important in magnetic recording devices. The saturation magnetization and optical band gap energy values of 62 emu/cc and 1.75 eV, respectively, were achieved for the film of thickness 500 nm deposited at 400 °C. Higher values of coercivity, squareness and films thickness are associated with the growth of larger grains at higher substrate temperature.     

Simulation analysis of the aluminum thin film thickness measurement by using low energy electron beam

This paper indicates a simulation analysis for estimating the aluminum (Al) thin film thickness measurements by using the low energy electron beam. In order to calculate the Al thickness estimation, the energy of the incident electron beams was varied from 10 to 30 keV, while the thickness of the Al film was varied between 6 and 14 μm. From the simulation results it was found that electron transmittance fraction in 14 μm sample is about nine orders of magnitude more than 6 μm sample at the same incident electron beam energy. Simulation results show that maximum transmitted electrons versus Al layer thickness has a parabolic relation and by using the obtained equation, it is possible to estimate unknown thickness of the thin film Al layer. All calculations here were done by CASINO numerical simulation package.     

Al(001)表面上沉积Ti薄膜的分子动力学模拟

采用分子动力学模拟方法,研究了Ti原子连续沉积于Al(001)表面上的薄膜生长过程,分析了入射能量为0.1、5 eV和衬底温度为300、700 K时的界面结合及微观结构.模拟结果表明,增加入射能量和衬底温度,使Ti薄膜的表面越光滑;通过径向分布函数和键对分析技术对薄膜微观结构进行分析,发现衬底温度时薄膜微观结构影响较大,温度300 K及以下时,Ti薄膜主要是FCC结构,随着温度升高,FCC结构成分减少,无序结构成分增加,而入射能量则对薄膜微观结构没有明显影响.     

A comparative study on structural and optical properties of ZnO and Al-doped ZnO thin films obtained by ultrasonic spray method using different solvents

Transparent conducting ZnO and Al doped ZnO thin films were deposited on glass substrate by ultrasonic spray method. The thin films with concentration of 0.1 M were deposited at 350 °C with 2 min of deposition time. The effects of ethanol and methanol solution before and after doping on the structural, optical and electrical properties were examined. The DRX analyses indicated that ZnO films have nanocrystalline nature and hexagonal wurtzite structure with (1 0 0) and (0 0 2) preferential orientation corresponding to ZnO films resulting from methanol and ethanol solution, respectively. The crystallinity of the thin films improved with methanol solution after doping to (0 0 2) oriented. All films exhibit an average optical transparency about 90%, in the visible range. The band gaps values of ZnO thin films are increased after doping from 3.10 to 3.26 eV and 3.27 to 3.30 eV upon Al doping obtained by ethanol and methanol solution, respectively. The electrical conductivity increase from 7.5 to 15.2 (Ω cm)⁻¹ of undoped to Al doped ZnO thin films prepared by using ethanol solution. However, for the methanol solution; the electrical conductivity of the film is stabilized after doping.     

The interplay between molecular orientation, film morphology and luminescence properties of tetracene thin films on epitaxial AlOx/Ni3Al(1 1 1)

We report a systematic study of the interplay between molecular orientation, film morphology and luminescence properties of tetracene thin films on epitaxial alumina films on Ni₃Al(1 1 1), employing high resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED), and photoluminescence spectroscopy (PL). If deposited at low temperatures, tetracene forms laterally disordered and compact films in which at least the first monolayer is oriented parallel to the substrate. For thicknesses in the range of 10 Å or below, these as-deposited films show no luminescence, while thicker films exhibit weak luminescence from higher layers. On annealing to 210 K, tetracene films dewet the AlO_x/Ni₃Al(1 1 1) surface and transform into an island morphology. At the same time, molecules tend to re-orient into a more upright configuration. In this island configuration, even thin films show luminescence. We can thus conclude that in spite of the insulating nature of the surface, the interaction of flat-lying tetracene molecules with AlO_x/Ni₃Al(1 1 1) is strong enough to provide at least one efficient non-radiative decay channel.     

Fabrication and vacuum annealing of transparent conductive Ga-doped Zn0.9Mg0.1O thin films prepared by pulsed laser deposition technique

In this study, highly transparent conductive Ga-doped Zn_0.9Mg_0.1O (ZMO:Ga) thin films have been deposited on glass substrates by pulsed laser deposition (PLD) technique. The effects of substrate temperature and post-deposition vacuum annealing on structural, electrical and optical properties of ZMO:Ga thin films were investigated. The properties of the films have been characterized through Hall effect, double beam spectrophotometer and X-ray diffraction. The experimental results show that the electrical resistivity of film deposited at 200 °C is 8.12 × 10⁻⁴ Ω cm, and can be further decreased to 4.74 × 10⁻⁴ Ω cm with post-deposition annealing at 400 °C for 2 h under 3 × 10⁻³ Pa. In the meantime, its band gap energy can be increased to 3.90 eV from 3.83 eV. The annealing process leads to improvement of (0 0 2) orientation, wider band gap, increased carrier concentration and blue-shift of absorption edge in the transmission spectra of ZMO:Ga thin films.     

Effect of temperature on pulsed laser deposition of HgCdTe films

HgCdTe thin films have been deposited on Si(1 1 1) substrates at different substrate temperatures by pulsed laser deposition (PLD). An Nd:YAG pulsed laser with a wavelength of 1064 nm was used as laser source. The influences of the substrate temperature on the crystalline quality, surface morphology and composition of HgCdTe thin films were characterized by X-ray diffraction (XRD), selected area electron diffraction (SAED), atomic force microscopy (AFM) and energy dispersive X-ray spectroscopy (EDS). The results show that in our experimental conditions, the HgCdTe thin films deposited at 200 °C have the best quality. When the substrate temperature is over 250 °C, the HgCdTe film becomes thermodynamically unstable and the quality of the film is degraded.     

Molecular dynamics simulation about porous thin-film growth in secondary deposition

The thin film growth has been confirmed to be assembled by an enormous number of clusters in experiments of CVD. Sequence of clusters’ depositions proceeds to form the thin film at short time as gas fluids through surface of substrate. In order to grow condensed thin film using series of cluster deposition, the effect of initial velocity, substrate temperature and density of clusters on property of deposited thin film, especially appearance of nanoscale pores inside thin film must be investigated. In this simulation, three different cluster sizes of 203, 653, 1563 atoms with different velocities (0, 10, 100, 1000 and 3000 m/s) were deposited on a Cu(0 0 1) substrate whose temperatures were set between 300 and 1000 K. Four clusters and one cluster were used in primary deposition and secondary deposition, respectively. We have clarified that adhesion between clusters and substrate is greatly influenced by initial velocity. As a result, the exfoliation pattern of deposited thin film is dependent on initial velocity and different between them. One borderline dividing whole region into porous region and nonporous region are obtained to show the effect of growth conditions on appearance of nanoscale pores inside thin film. Moreover, we have also shown that the likelihood of porous thin film is dependent on the point of impact of a cluster relative to previously deposited clusters.     

Effect of annealing on properties of electrochemically deposited CdTe thin films

Thin films of CdTe have been deposited onto stainless steel and fluorine-doped tin oxide (FTO)-coated glass substrates from aqueous acidic bath using electrodeposition technique. The different preparative parameters, such as deposition time, bath temperature and pH of the bath have been optimized by photoelectrochemical (PEC) technique to get good quality photosensitive material. The deposited films are annealed at different temperature in presence of air. Annealing temperature is also optimized by PEC technique. The film annealed at 200 °C showed maximum photosensitivity. Different techniques have been used to characterize as deposited and also as annealed (at 200 °C) CdTe thin film. The X-ray diffraction (XRD) analysis showed the polycrystalline nature, and a significant increase in the XRD peak intensities is observed for the CdTe films after annealing. Optical absorption shows the presence of direct transition with band gap energy 1.64 eV and after annealing it decreases to 1.50 eV. Energy dispersive analysis by X-ray (EDAX) study for the as-deposited and annealed films showed nearly stoichiometric compound formation. Scanning electron microscopy (SEM) reveals that spherically shaped grains are more uniformly distributed over the surface of the substrate for the CdTe film.     

Optical properties of selenium-tellurium nanostructured thin film grown by thermal evaporation

Se-Te nanostructured thin films were deposited on glass substrates in the presence of oxygen and argon by thermal evaporation. The properties of Se-Te thin films strongly depend on the deposition method. During the process used, the substrate is cooled to a temperature of 77 K employing liquid nitrogen. The nanostructured thin films of Se_100−xTe_x (where x=4, 8 and 16) are deposited on glass substrate. The surface morphology of the deposited films was investigated through Scanning Electron Microscopy (SEM). The typical size of these nanostructures is in the range 40-100 nm and the length is of the order of several micrometers. The optical parameters i.e. optical gap (E_g), absorption coefficient (α), and extinction coefficient (k) are calculated in the wavelength range 190-1100 nm. It was found that the optical band gap decreased from 3.4 to 2.9 eV when Te concentration was increased in the Se_100−xTe_x nanostructured thin films. The large bandgap may be attributed to the decrease in particle size which clearly exhibits a quantum size effect. XRD analysis was performed to confirm glassy nature of the nanostructured thin films.     

Optical and electrical properties of aluminum zinc oxide (AZO) nanostructured thin film deposited on polycarbonate substrate

Transparent polymer materials, due to their unique properties, such as light weight, optical transparency, and electrical and mechanical properties, have become very attractive as a replacement for inorganic glass substrates in a wide range of optoelectronic applications. In this research, aluminum zinc oxide nanostructured thin film was deposited on polycarbonate polymer substrates using a magnetron sputtering technique. The structure, morphology, and surface composition of the thin film were investigated by X-ray diffraction and field emission scanning electron microscopy. The optical and electrical properties of the thin film were investigated by UV–VIS-NIR spectrophotometer, ellipsometer, and four point probe method. The X-ray diffraction pattern showed that the aluminum zinc oxide thin film had a polycrystalline structure. The optical and electrical results indicated that the refractive index, band gap, and sheet resistance of the aluminum zinc oxide thin film were 1.8, 3.2 eV, and 265 Ω/sq, respectively.