The preparation of c-axis epitaxial Bi-2212 films on STO(1 0 0) by sol-gel method

Bi₂Sr₂Ca₁Cu₂O_8+δ (Bi-2212) films were grown on (1 0 0) oriented SrTiO₃ (STO) substrate using sol-gel spin-coating method. The effects of heat treatment conditions and coating times on the phase formation and surface morphology were investigated using thermal analysis, optical microscope, X-ray diffraction, and scanning electronic microscopy. Mixed phases were formed from 820 to 840 °C, and Bi-2212 single phase was obtained at 830 °C for 3 h. c-axis epitaxial films with smooth surfaces were obtained by drying at 600 °C and coating for 5 times.     

A novel UV-emitting phosphor: Li6CaB3O8.5:Pb

Pure Li₆CaB₃O_8.5 and Li₆Ca_1−xPb_xB₃O_8.5 (0.005≤x≤0.04) materials were prepared by a solution combustion synthesis method. The phase of synthesized materials was determined using the powder XRD and FTIR. The synthesized materials were investigated using spectrofluorometer at room temperature. The emission and excitation bands of the synthesized phosphors were observed at 307 and 268 nm, respectively. The dependence of the emission intensity on the Pb²⁺ concentration for the Li₆Ca_1−xPb_xB₃O_8.5 (0.005≤x≤0.04) was studied and observed that the optimum concentration of Pb²⁺ in phosphor is 0.01 mol. The Stokes shift of the synthesized phosphor was calculated to be 4740 cm^-1.     

Enhanced luminescence of Ca3B2O6:Dy phosphors by Na-codoping for LED applications

The Ca_2.95−yDy_0.05B₂O₆:yNa⁺ (0≤y≤0.20) phosphors were synthesized at 1100 °C in air by the solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), photoluminescence excitation (PLE), photoluminescence (PL) spectra and thermoluminescence (TL) spectra. The PLE spectra show the excitation peaks from 300 to 400 nm due to the 4f-4f transitions of Dy³⁺. This mercury-free excitation is useful for solid-state lighting and light-emitting diodes (LEDs). The emission of Dy³⁺ ions on 350 nm excitation was observed at 480 nm (blue) due to the ⁴F_9/2→⁶H_15/2 transitions, 575 nm (yellow) due to ⁴F_9/2→⁶H_13/2 transitions and 660 nm (red) due to weak ⁴F_9/2→⁶H_11/2 emissions. The PL results from the investigated Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors show that Dy³⁺ emissions increase with the increase of the Na⁺ codoping ions. The integral intensity of yellow to blue (Y/B) can be tuned by controlling Na⁺ content. By the simulation of white light, the optimal CIE value (0.328, 0.334) can be achieved when the content of Na⁺-codoping ions is y=0.2. The results imply that the Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors could be potentially used as white LEDs.     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Emission analysis of Pr and Tm: Ca2Gd2W3O14 phosphors

5 mol% of Pr³⁺ and Tm³⁺ ions activated calcium gadolinium tungstate (Ca₂Gd₂W₃O₁₄₎ phosphors were synthesized by traditional solid state reaction method. Crystalline phase structure was identified from the X-ray diffraction (XRD) profiles. From the scanning electron microscopy (SEM) images, we have observed the agglomeration of the particles, and average grain size is around 40-300 nm. Using the energy dispersive X-ray analysis (EDAX) and Fourier transform infrared (FTIR) spectra, identified the elements and functional groups present in the prepared phosphors. The emission spectrum of Pr³⁺: Ca₂Gd₂W₃O₁₄ powder phosphors have shown an intense red emission at 615 nm with the excitation wavelength λ_exci=450 nm and thus these red color emitting powder phosphors are used as one of the components in the preparation of WLEDs. The excitation spectrum of Tm³⁺: Ca₂Gd₂W₃O₁₄ powder phosphor has shown a ligand to metal charge transfer (W-O) band (LMCT) within the WO₄²⁻ group. Emission spectrum of Tm³⁺: Ca₂Gd₂W₃O₁₄ phosphors have shown blue emissions at 453 nm (¹D₂→³F₄).     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.     

Surface study of fine MgFe2O4 ferrite powder prepared by chemical methods

To study surface behaviors, MgFe₂O₄ ferrite materials having different grain sizes were synthesized by two different chemical methods, i.e., a polymerization method and a reverse coprecipitation method. The single phase of the cubic MgFe₂O₄ was confirmed by the X-ray diffraction method for both the precursors decomposed at 600-1000 °C except for a very small peak of Fe₂O₃ was detected for the samples calcined at 600 and 700 °C by the polymerization method. The crystal size and particle size increased with an increase in the sintering temperature using both methods. The conductance of the MgFe₂O₄ decreased when the atmosphere was changed from ambient air to air containing 10.0 ppm NO₂. The conductance change, C = G(air)/G(10 ppm NO₂), was reduced with an increase in the operating temperature. For the polymerization method, the maximum C-value was ca. 40 at 300 °C for the samples sintered at 900 °C. However, the samples sintered at 1000 °C showed a low conductance change in the 10 ppm NO₂ gas, because the ratio of the O₂ gas adsorption sites on the particle surface is smaller than those of the samples having a high C-value. The low Mg content on the surface affects the low ratio of the gas adsorption sites. For the reverse coprecipitation method, the particle size was smaller than that of the polymerization method. Although a stable conductance was obtained for the sample sintered at 900 and 1000 °C, its conductance change was less than that of the polymerization method.     

KrF pulsed laser deposition of La5Ca9Cu24O41 thin films on various substrates

Recent studies on single crystals of cuprate oxides containing spin chains and ladders have reported large anisotropic magnon-mediated thermal conductivity. A potential use of thin films of such materials could be in the thermal management of electronic devices for the guiding of unwanted heat to a heat sink. In this article, the pulsed laser deposition and characterization of La₅Ca₉Cu₂₄O₄₁ thin films on SrLaAlO₄, SrTiO₃, MgO, and Si substrates are reported for the first time. The films were grown using a pulsed UV laser (KrF, 248 nm) and various substrate temperatures up to 650 °C. The XRD spectra revealed successful target-film stoichiometric transfer and high texturing of the thin films with (0 k 0) preferred orientation.     

Stability of La2O3 and GeO2 passivated Ge surfaces during ALD of ZrO2 high-k dielectric

La₂O₃ grown by atomic layer deposition (ALD) and thermally grown GeO₂ are used to establish effective electrical surface passivations on n-type (1 0 0)-Ge substrates for high-k ZrO₂ dielectrics, grown by ALD at 250 °C substrate temperature. The electrical characterization of MOS capacitors indicates an impact of the Ge-surface passivation on the interfacial trap density and the frequency dependent capacitance in the inversion regime. Lower interface trap densities can be obtained for GeO₂ based passivation even though a chemical decomposition of the oxidation states occur during the ALD of ZrO₂. As a consequence the formation of a ZrGeO_x compound inside the ZrO₂ matrix and a decline of the interfacial GeO₂ are observed. The La₂O₃ passivation provides a stable amorphous lanthanum germanate phase at the Ge interface but also traces of Zr germanate are indicated by X-ray-Photoelectron-Spectroscopy and Transmission-Electron-Microscopy.     

Characterization of Y2O3 gate dielectric on n-GaAs substrates

Physical and electrical properties of sputtered deposited Y₂O₃ films on NH₄OH treated n-GaAs substrate are investigated. The as-deposited films and interfacial layer formation have been analyzed by using X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). It is found that directly deposited Y₂O₃ on n-GaAs exhibits excellent electrical properties with low frequency dispersion (<5%), hysteresis voltage (0.24 V), and interface trap density (3 × 10¹² eV⁻¹ cm⁻²). The results show that the deposition of Y₂O₃ on n-GaAs can be an effective way to improve the interface quality by the suppression on native oxides formation, especially arsenic oxide which causes Fermi level pinning at high-k/GaAs interface. The Al/Y₂O₃/n-GaAs stack with an equivalent oxide thickness (EOT) of 2.1 nm shows a leakage current density of 3.6 × 10⁻⁶ A cm⁻² at a V_FB of 1 V. While the low-field leakage current conduction mechanism has been found to be dominated by the Schottky emission, Poole-Frenkel emission takes over at high electric fields. The energy band alignment of Y₂O₃ films on n-GaAs substrate is extracted from detailed XPS measurements. The valence and conduction band offsets at Y₂O₃/n-GaAs interfaces are found to be 2.14 and 2.21 eV, respectively.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Effect of Li2O and CoO-doping of CuO/Fe2O3 system on its surface and catalytic properties

Physicochemical, surface and catalytic properties of pure and doped CuO/Fe₂O₃ system were investigated using X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), nitrogen adsorption at −196 °C and CO-oxidation by O₂ at 80-220 °C using a static method. The dopants were Li₂O (2.5 mol%) and CoO (2.5 and 5 mol%). The results revealed that the increase in precalcination temperature from 400 to 600 °C and Li₂O-doping of CuO/Fe₂O₃ system enhanced CuFe₂O₄ formation. However, heating both pure and doped solids at 600 °C did not lead to complete conversion of reacting oxides into CuFe₂O₄. The promotion effect of Li₂O dopant was attributed to dissolution of some of dopant ions in the lattices of CuO and Fe₂O₃ with subsequent increase in the mobility of reacting cations. CoO-doping led also to the formation of mixed ferrite Co_xCu_1−xFe₂O₄. The doping process of the system investigated decreased to a large extent the crystallite size of unreacted portion of Fe₂O₃ in mixed solids calcined at 600 °C. This process led to a significant increase in the S_BET of the treated solids. Doping CuO/Fe₂O₃ system with either Li₂O or CoO, followed by calcination at 400 and 600 °C decreased its catalytic activity in CO-oxidation by O₂. However, the activation energy of the catalyzed reaction was not much affected by doping.     

An XPS study and electrical properties of Pb1.1Zr0.53Ti0.47O3/PbO/Si (MFIS) structures according to the substrate temperature of the PbO buffer layer

PbO and PZT thin films were deposited on the p-type (1 0 0) Si substrate by the rf magnetron sputtering method with PbO and Pb_1.1Zr_0.53Ti_0.47O₃ targets for the application of the metal-ferroelectric-insulator-semiconductor (MFIS) structure. The MFIS structures with the PbO buffer layer show the good electric properties including a high memory window and a low leakage current density. The maximum value of the memory window is 2.0 V under the applied voltage of 9 V for the Pt/PZT (200 nm, 400 °C)/PbO (80 nm)/Si structures with the PbO buffer layer deposited at the substrate temperature of 300 °C. From the X-ray photoelectron spectroscopy (XPS) results, we could confirm that the substrate temperature of PbO affects the chemical states of the interface between the PbO buffer layer and Si substrate, which results in the inter-diffusion of Pb and the formation of the intermediate phases (PbSiO₃). And the existence of the undesired SiO₂ layer, which is the low dielectric layer, was confirmed at the surface region of the Si substrate by the XPS depth profile analysis.     

Thermal stability, oxygen non-stoichiometry and transport properties of LaNi0.6Fe0.4O3

Thermal stability, oxygen non-stoichiometry and electrical conductivity of LaNi_0.6Fe_0.4O_3−δ were investigated in the temperature region of 20-1000 °C in Ar/O₂ gas flows at oxygen partial pressures between 0.5 and 21,000 Pa. Diffusion mobility was measured in Ar/O₂ gas flow at pO₂ = 18 Pa. Crystal structure of this compound was found to be stable at the mentioned experimental conditions. LaNi_0.6Fe_0.4O_3−δ is a p-type semiconductor with metallic type conductivity above 150 °C at the investigated pO₂ range. Two different (fast and slow) oxygen exchange areas on the temperature-pO₂ diagram were established, which are due to two different oxygen anion positions in the double B-site mixed perovskite structure. Oxygen non-stoichiometry in the fast oxygen exchange region reaches about 0.005 of oxygen atomic index. Chemical diffusion and oxygen surface exchange coefficients do not vary at 600-800 °C, but show visible increase above 800-850 °C.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Synthesis and ion conductivity of (Bi2O3)0.75(Dy2O3)0.25 ceramics with grain sizes from the nano to the micro scale

Using (Bi₂O₃)_0.75(Dy₂O₃)_0.25 nano-powder synthesized by reverse titration co-precipitation method as raw material, dense ceramics were sintered by both Spark Plasma Sintering (SPS) and pressureless sintering. According to the predominance area diagram of Bi-O binary system, the sintering conditions under SPS were optimized. (Bi₂O₃)_0.75(Dy₂O₃)_0.25 ceramics with relative density higher than 95% and an average grain size of 20 nm were sintered in only 10 min up to 500 °C. During the pressureless sintering process, the grain growth behavior of (Bi₂O₃)_0.75(Dy₂O₃)_0.25 followed a parabolic trend, expressed as D² − D₀² = Kt, and the apparent activation energy of grain growth was found to be 284 kJ mol^− 1. Dense (Bi₂O₃)_0.75(Dy₂O₃)_0.25 ceramics with different grain sizes were obtained, and the effect of grain size on ion conductivity was investigated by impedance spectroscopy. It was shown that the total ion conductivity was not affected by the grain size down to 100 nm, however lower conductivity was measured for the sample with the smallest grain size (20 nm). But, although only the δ phase was evidenced by X-ray diffraction for this sample, a closer inspection by Raman spectroscopy revealed traces of α-Bi₂O₃.     

Preparation and characterization of polyaniline (PANI)-Mn3O4 nanocomposite

Polyaniline (PANI)-Mn₃O₄ nanocomposite was synthesized by a combination of sonochemical synthesis of Mn₃O₄ NP's and in-situ polymerization of aniline. Structural characteristics were evaluated by XRD, FT-IR, TGA, VSM, TEM and SEM analysis, and conduction characteristics were evaluated by total conductivity measurements in the temperature range of 20-100 °C and frequency range of 0.1 Hz-1 MHz. Our findings show that PANI is successfully coated on nanoparticles surface and overall conductivity of nanocomposite is approximately 50-1000 times higher than that of uncapped Mn₃O₄ or PANI base with increase in temperature. Morphology of the synthesized powder was observed to be thin nanosheets with a thickness of 2-3 nm based on SEM analysis. Room temperature magnetization curves for nanocomposite show no hysteresis, indicating the super-paramagnetic character of the sample in the region of measured field strength. σ_AC increased after polyaniline coating.     

Promotion of surface SOx on the selective catalytic reduction of NO by hydrocarbons over Ag/Al2O3

The promotion of sulfur oxides on the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of a low concentration of sulfur oxides over Ag/Al₂O₃ has been investigated by a flow reaction test and in situ infrared spectroscopy. When the C₃H₆ (or C₁₀H₂₂) + NO + O₂ feed-flow reaction was tested, maximum NO reduction was below 30% over fresh Ag/Al₂O₃. After the addition of SO₂ to the feed flow, conversion increased slightly. Conversion increased further after SO₂ was cut-off from the feed flow. This demonstrated that the increase in NO reduction activity of the catalyst was related to SO_x adsorbed on the catalyst. SO_x adsorbed on the catalytic surface (1375 cm⁻¹) was detected by IR spectroscopy and was stable within the temperature range. NCO species, as an intermediate in NO reduction, on SO_x-adsorbed Ag/Al₂O₃ in a C₃H₆ + NO + O₂ feed flow was observed in in situ IR spectra during the elevation of the reaction temperature from 473 to 673 K, while it was only observed at 673 K on fresh Ag/Al₂O₃ under the same experimental conditions. We suggest that SO_x in low concentrations depressed the combustion of reductants by contaminating hydrocarbon combustion active sites on the catalyst, resulting in an increase in NO reduction efficiency of the reductants.