Effect of oxygen pressure on structure and properties of Bi1.5Zn1.0Nb1.5O7 pyrochlore thin films prepared by pulsed laser deposition

The Bi₂O₃-ZnO-Nb₂O₅ (BZN) cubic pyrochlore thin films were prepared on Pt/TiO₂/SiO₂/Si(1 0 0) substrates by using pulsed laser deposition process. The oxygen pressure was varied in the range of 5-50 Pa to investigate its effect on the structure and dielectric properties of BZN thin films. It is found that oxygen pressure during deposition plays an important role on structure and other properties of BZN films. The BZN films deposited at temperature of 650 °C and at O₂ pressure of 5 Pa have an amorphous BZN and Nb₂O₅ phases but exhibits a cubic pyrochlore structure with a preferential (2 2 2) orientation when the oxygen pressure increases to 10 Pa. Dielectric constant and loss tangent of the films deposited at 10 Pa are 185 and 0.0008 at 10 kHz, respectively. The dielectric tunability is about 10% at a dc bias field of 0.9 MV/cm.     

Multilayer Bi1.5Zn1.0Nb1.5O7/Ba0.6Sr0.4TiO3/Bi1.5Zn1.0Nb1.5O7 thin films for tunable microwave applications

Bi_1.5Zn_1.0Nb_1.5O₇/Ba_0.6Sr_0.4TiO₃/Bi_1.5Zn_1.0Nb_1.5O₇ tunable multilayer thin film has been fabricated by pulsed laser ablation and characterized. Phase composition and microstructure of multilayer films were characterized by X-ray diffraction, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The film has very smooth surface with RMS roughness of 1.5-2 nm and grain size of 100-150 nm. Total film thickness has been measure to be 375 nm. The BZN thin films at 300 K, on Pt(1 1 1)/SiO₂/Si substrate showed zero-field dielectric constant of 105 and dielectric loss tangent of 0.002 at frequency of 0.1 MHz. Thin films annealed at 700 °C shows the dielectric tunability of 18% with biasing field 500 kV/cm at 0.1 MHz. The multilayer thin film shows nonferroelectric behavior at room temperature. The good physical and electrical properties of multilayer thin films make them promising candidate for tunable microwave device applications.     

KrF pulsed laser deposition of La5Ca9Cu24O41 thin films on various substrates

Recent studies on single crystals of cuprate oxides containing spin chains and ladders have reported large anisotropic magnon-mediated thermal conductivity. A potential use of thin films of such materials could be in the thermal management of electronic devices for the guiding of unwanted heat to a heat sink. In this article, the pulsed laser deposition and characterization of La₅Ca₉Cu₂₄O₄₁ thin films on SrLaAlO₄, SrTiO₃, MgO, and Si substrates are reported for the first time. The films were grown using a pulsed UV laser (KrF, 248 nm) and various substrate temperatures up to 650 °C. The XRD spectra revealed successful target-film stoichiometric transfer and high texturing of the thin films with (0 k 0) preferred orientation.     

Effect of deposition temperature on orientation and electrical properties of (K0.5Na0.5)NbO3 thin films by pulsed laser deposition

Lead-free ferroelectric K_0.5Na_0.5NbO₃ (KNN) thin films have been prepared on Pt/TiO₂/SiO₂/Si substrates by pulsed laser deposition process. The structures, crystal orientations and electrical properties of thin films have been investigated as a function of deposition temperature from 680 °C to 760 °C. It is found that the deposition temperature plays an important role in the structures, crystal orientations and electrical properties of thin films. The crystallization of thin films improves with increasing deposition temperature. The thin film deposited at 760 °C exhibits strong (0 0 1) preferential orientation, large dielectric constant of 930 and the remnant polarization of 8.54 μC/cm².     

Structural, optical and magnetic properties of Nd-doped BiFeO3 thin films prepared by pulsed laser deposition

Nd-doped BiFeO₃ thin films were grown by pulsed laser deposition on quartz substrate and their structural, optical and magnetic properties have been studied. X-ray diffraction analysis revealed that Nd addition caused structural distortion even with 5% of Nd concentration, additional secondary phase appeared in all samples but its intensity was greatly reduced with Nd addition. Doping-induced variations in texture and structure modifying both magnetic and optical properties of BiFeO₃ thin films. The energy band gap decreases while the refractive index increases with addition of Nd³⁺ in BiFeO₃ for Bi³⁺. These variations in energy band gap and refractive index have been explained on the basis of density of states and increase in disorders in the system. All the samples were found to exhibit ferromagnetism at room temperature and the saturation magnetization increases with the increase in structural distortion with addition of Nd. Finally, Nd-doping modifies the physical properties of BiFeO₃ in comparison to undoped BiFeO₃ thin films.     

Pulsed laser deposition of Bi2Te3 thermoelectric films

Bi₂Te₃ is one of the most used materials for thermoelectric applications at ambient temperature. An improvement of thermoelectric performances through a suitable modification of electron and phonon transport mechanisms is predicted for low dimensional or nanostructured systems, but this requires a control of the material structure down to the nanoscale. We show that pulsed laser deposition provides control on film composition, phase and structure, necessary for a comprehension of the relationship between structure and thermoelectric properties. We have explored the role of deposition temperature, background inert gas type and pressure, laser fluence and target-to-substrate distance and we found the experimental condition ranges to obtain crystalline films containing the Bi₂Te₃ phase only, by comparing energy dispersive X-ray spectroscopy, Raman spectroscopy and X-ray diffraction analysis. Variations of substrate temperature and deposition gas pressure prove to be crucial also for the control of film morphology and crystallinity. Substrate type has no influence on film stoichiometry and crystallinity, but highly oriented growth can be achieved on mica due to van der Waals epitaxy.     

High temperature thermoelectric properties of highly c-axis oriented Bi2Sr2Co2Oy thin films fabricated by pulsed laser deposition

High-temperature thermoelectric transport property measurements have been performed on the highly c-axis oriented Bi2Sr2Co20v thin films prepared by pulsed laser deposition on LaA1Oa （001）. Both the electric resistivity p and the seebeck coefficient S of the film exhibit an increasing trend with the temperature from 300 K-1000 K and reach up to 4.8 m. cm and 202 V/K at 980 K, resulting in a power factor of 0.85 mW/mK which are comparable to those of the single crystalline samples. A small polaron hopping conduction can be responsible for the conduction mechanism of the film at high temperature. The results demonstrate that the Bi2Sr2Co2Oy thin film has potential application has high temperature thin film thermoelectric devices,     

Lead-free ferroelectric BaTiO3 doped-(Na0.5Bi0.5)TiO3 thin films processed by pulsed laser deposition technique

The difficulties in synthesizing phase pure BaTiO₃ doped-(Na_0.5Bi_0.5)TiO₃ are known. In this work, we reporting the optimized pulsed laser deposition (PLD) conditions for obtaining pure phase 0.92(Na_0.5Bi_0.5)TiO₃-0.08BaTiO₃, (BNT-BT_0.08), thin films. Dielectric, ferroelectric and piezoelectric properties of BNT-BT_0.08, thin films deposited by PLD on Pt/TiO₂/SiO₂/Si substrates are investigated in this paper. Perovskite structure of BNT-BT_0.08 thin films with random orientation of nanocrystallites has been obtained by deposition at 600 °C. The relative dielectric constant and loss tangent at 100 kHz, of BNT-BT_0.08 thin film with 530 nm thickness, were 820 and 0.13, respectively. Ferroelectric hysteresis measurements indicated a remnant polarization value of 22 μC/cm² and a coercive field of 120 kV/cm. The piezoresponse force microscopy (PFM) data showed that most of the grains seem to be constituted of single ferroelectric domain. The as-deposited BNT-BT_0.08 thin film is ferroelectric at the nanoscale level and piezoelectric.     

衬底温度对PLD法生长的Mg0.05Zn0.95O薄膜结构和发光特性的影响

用脉冲激光沉积(PLD)法在不同温度的Si(111)衬底上成功制备了c轴择优取向的Mg_005Zn_095O薄膜.通过X射线衍射(XRD)和光致发光谱(PL)研究了衬底温度对Mg_005Zn_095O薄膜结构和发光特性的影响,探讨了薄膜的结晶质量与发光特性之间的关系.结果表明,在衬底温度为450℃时生长的Mg_005Zn_095O薄膜具有很好的c轴取向和较强的光致发光峰.室温下分别用激发波长为240,300和325nm的氙灯作为激发光源得到不同样品的PL谱,分析表明紫外发光峰和紫峰来源于自由激子的复合辐射且发光强度与薄膜的结晶质量密切相关,蓝绿发光峰与氧空位有关.此外,探讨了衬底温度影响紫外光致发光峰红移和蓝移的可能机理. 关键词： 005Zn_095O薄膜')" href="#">Mg_005Zn_095O薄膜 PLD 衬底温度 光致发光     

Influence of substrate temperature and post-treatment on the properties of ZnO:Al thin films prepared by pulsed laser deposition

Highly transparent conductive Al₂O₃ doped zinc oxide (AZO) thin films have been deposited on the glass substrate by pulsed laser deposition technique. The effects of substrate temperature and post-deposition annealing treatment on structural, electrical and optical properties of AZO thin films were investigated. The experimental results show that the electrical resistivity of films deposited at 240 °C is 6.1 × 10⁻⁴ Ω cm, which can be further reduced to as low as 4.7 × 10⁻⁴ Ω cm by post-deposition annealing at 400 °C for 2 h in argon. The average transmission of AZO films in the visible range is 90%. The optical direct band gap of films was dependent on the substrate temperature and the annealing treatment in argon. The optical direct band gap value of AZO films increased with increasing annealing temperature.     

LiFePO4 thin films grown by pulsed laser deposition: Effect of the substrate on the film structure and morphology

Well crystallized and homogeneous LiFePO₄/C (LFPO) thin films have been grown by pulsed laser deposition (PLD). The targets were prepared by the sol-gel process at 600 °C. The structure of the polycrystalline powders was analyzed with X-ray powder diffraction (XRD) data. The XRD patterns were indexed having a single phase olivine structure (Pnma). LFPO thin films have been deposited on three different substrates: aluminum (Al), stainless steel (SS) and silicon (Si) by pulsed laser deposition (PLD). The structure of the films was analyzed by X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). It is found that the crystallinity of the thin films depends on the substrate temperature which was set at 500 °C. When annealed treatments were used, secondary phases were found, so, one step depositions at 500 °C were made.Stainless steel is demonstrated to be the best choice to act as substrate for phosphate deposition. LiFePO₄ thin films grown on stainless steel plates exhibited the presence of carbon, inducing a slight conductivity enhancement that makes these films promising candidates as one step produced cathodes in Li-ion microbatteries.     

Effects of deposition temperature on the structural and morphological properties of SnO2 films fabricated by pulsed laser deposition

Tin oxide (SnO₂) thin films were grown on Si (1 0 0) substrates using pulsed laser deposition (PLD) in O₂ gas ambient (10 Pa) and at different substrate temperatures (RT, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using X-ray diffraction (XRD), atomic force microscopy (AFM) and scanning electron microscopy (SEM). XRD measurements showed that the almost amorphous microstructure transformed into a polycrystalline SnO₂ phase. The film deposited at 400 °C has the best crystalline properties, i.e. optimum growth conditions. However, the film grown at 300 °C has minimum average root mean square (RMS) roughness of 3.1 nm with average grain size of 6.958 nm. The thickness of the thin films determined by the ellipsometer data is also presented and discussed.     

脉冲激光沉积温度及氧压对Bi2Sr2Co2Oy热电薄膜晶体结构与电输运性能的影响

利用脉冲激光沉积技术在c-Al₂O₃单晶基片上制备了Bi₂Sr₂Co₂O_y热电薄膜并研究了沉积温度和氧压对薄膜晶体结构及电输运性能的影响.在最佳沉积条件下制备的单相、c轴取向的Bi₂Sr₂Co₂O_y薄膜的室温电阻率ρ和塞贝克系数S分别为2.9mΩ/cm和110μupV/K,其功率因子S²/ρ好于在单晶样品上得到的值.此外,该薄膜在低温下表现出较强的负磁阻效应,在2K,9T时达到了40%.     

Characterization of polymer thin films obtained by pulsed laser deposition

The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate).The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry.It was found that for laser fluences up to 1.5 J/cm² the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm² the polyepichlorohydrin films present deviations from the bulk polymer.Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm²).The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material.The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.     

Structural and optical properties of SrCu2O2 films deposited on sapphire substrates by pulsed laser deposition

We deposited SrCu₂O₂ (SCO) films on sapphire (Al₂O₃) (0 0 0 1) substrates by pulsed laser deposition. The crystallographic orientation of the SCO thin film showed clear dependence on the growth temperature. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis showed that the film deposited at 400 °C was mainly oriented in the SCO [2 0 0] direction, whereas when the growth temperature was increased to 600 °C, the SCO film showed a dominant orientation of SCO [1 1 2]. The SCO film deposited at 500 °C was obvious polycrystalline, showing multi peaks from (2 0 0), (1 1 2), and (2 1 1) diffraction in the XRD spectrum. The SCO film deposited at 600 °C showed a band gap energy of 3.3 eV and transparency up to 80% around 500 nm. The photoluminescence (PL) spectra of the SCO films grown at 500 °C and 600 °C mainly showed blue-green emission, which was attributed to the intra-band transition of the isolated Cu⁺ and Cu⁺–Cu⁺ pairs according to the temperature dependent-PL analysis.     

Vanadium-Al2O3 nanostructured thin films prepared by pulsed laser deposition: Optical switching

The formation and optical response of VO_x nanoparticles embedded in amorphous aluminium oxide (Al₂O₃) thin films by pulsed laser deposition is studied. The thin films have been grown by alternate laser ablation of V and Al₂O₃ targets, which has resulted in a multilayer structure with embedded nanoparticles. The V content has been varied by changing the number of pulses on the V target. It is found that VO_x nanoparticles with dimensions around 5 nm have been formed. The structural analysis shows that the vanadium nanoparticles are oxidized, although probably there is not a unique oxide phase for each sample. The films show a different optical response depending on their vanadium content. Optical switching as a function of temperature has been observed for the two films with the highest vanadium content, at transition temperatures of about −20 °C and 315 °C thus suggesting the presence of nanoparticles with compositions V₄O₇ and V₂O₅, respectively.     

Enhanced dielectric permittivity in poly (vinylidene) fluoride/multiwalled carbon nanotubes nanocomposite thin films fabricated by pulsed laser deposition

The fabrication of high quality thin films of poly (vinylidene fluoride) embedded with multiwalled carbon nanotubes using pulsed laser deposition technique is reported. The prepared films were characterized for structural, morphology and dielectric properties. The morphology analysis revealed uniform dispersion of multiwalled carbon nanotubes throughout the polymer matrix. X-ray diffraction results suggested that the poly (vinylidene fluoride) film is in amorphous phase while addition of multiwalled carbon nanotubes showed presence of crystalline peaks in the nanocomposites films. It was interesting to note that the nanocomposite films exhibits significant enhancement of the ferroelectric β-phase as evidenced by the X-ray diffraction and Fourier transform infrared spectroscopy results. The dielectric analysis shows a remarkable enhancement in the dielectric permittivity of nanocomposites with lower loss and conductivity level. The results can be attributed to the formation of minicapacitor network and relatively higher percolation threshold in the nanocomposites.     

Chemical bath deposition of hausmannite Mn3O4 thin films

A low-temperature chemical bath deposition (CBD) technique has been used for the preparation of Mn₃O₄ thin films onto glass substrates. The kinetic behavior and the formation mechanism of the solid thin films from the aqueous solution have been investigated. Structure (X-ray diffraction and Raman), morphological (atom force microscope), and optical (UV-vis-NIR) characterizations of the deposited films are presented. The results indicated that the deposited Mn₃O₄ thin films of smooth surface with nanosized grains were well crystalline and the optical bandgap of the film was estimated to be 2.54 eV.     

VO2-WO3 nanocomposite thin films synthesized by pulsed laser deposition technique

Pure VO₂ and VO₂-WO₃ composite thin films were grown on quartz substrate by pulsed laser deposition (PLD) technique. The influence of varying WO₃ molar concentration in the range from x = 0.0 to x = 0.4 on structural, electrical and optical properties of VO₂-WO₃ nanocomposite thin films has been systematically investigated. X-ray diffraction studies reveal the single crystalline monoclinic VO₂ phase (m-VO₂) up to 10% of WO₃ content whereas both m-VO₂ as well as h-WO₃ (hexagonal WO₃) phases were present at higher WO₃ content (0.2 ≤ x ≤ 0.4). Optical transmittance spectra of the films showed blue shift in the absorption edge with increase in WO₃ content. Temperature dependence of resistivity (R-T) measurements indicates significant variation in metal-insulator transition temperature, width of the hysteresis, and shape of the hysteresis curve. Cyclic Voltammetry measurements were performed on VO₂-WO₃ thin films. A direct correlation between V/W ratio and structure-property relationship was established. The present investigations reveal that doping of WO₃ in VO₂ is effective to increase the optical transmittance and to reduce the semiconductor to metal phase transition temperature close to room temperature.