Study on the effect of different acids on the structure and photocatalytic activity of mesoporous titania

Nanocrystalline mesoporous titania was synthesized via a combined sol–gel process with surfactant-assisted templating method using cetyltrimethyl ammonium bromide (CTAB) as the structure-directing agent. The process was catalyzed by different acid (hydrochloric acid, nitric acid, sulfuric acid, or phosphoric acid). The prepared samples were characterized by XRD, TEM, BET and FT-IR. The photocatalytic activity of the samples was determined by degradation of phenol in aqueous solution. Results showed that different acid had different effect on the structure and crystal phase of the samples. The sample adjusted by phosphoric acid showed highest surface area and photocatalytic activity. The formation mechanism of the samples catalyzed by different acid was also discussed.     

Properties of mesoporous tungstosilicic acid/titania composites prepared by sol-gel method

The tungstosilicic acid/titania composites were prepared by the sol-gel method. Titanium isopropoxide was used as titania precursor, and urea as a low-cost template. The tungstosilicic acid (TSA) was added in the same step as that in which titania hydrogel is formed. The TSA-modified samples only showed the characteristic peaks of anatase phase of titanium oxide in the XRD patterns, indicating that the presence of TSA retarded the crystallization of the anatase phase and its transformation into the rutile phase. Spherical particles with sizes between 200 and 700 nm, formed by aggregation of nanoparticle aggregates (4-50 nm in size), were observed. The particle size increased when the TSA content was raised and also increased slightly with the thermal treatment temperature. Mesoporous materials were obtained, with a mean pore diameter higher than 3.1 nm. Both the increase of the TSA concentration in the solid and the calcination temperature led to a decrease in the specific surface area of the samples. The main heteropolyoxometallate species present in the composites is the [SiW₁₂O₄₀]⁴⁻ anion for the composites calcined up to 500 °C. The band gap energy decreased as a result of the introduction of TSA into the titania matrix, though it remained almost constant with the calcination temperature increase.     

Effect of heat treatment on bioactivity of anodic titania films

Anodic oxidation could be employed to produce crystalline titania films on Ti6Al4 V surfaces for inducing apatite formation in simulated body fluid (SBF). In this work, the effect of further heat treatment on the bioactivity of anodic titania films was researched. The surface constitution, morphology, crystal structure and apatite-forming ability of titania films were characterized by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results indicated the apatite formation on the Ti6Al4 V surfaces could be attributed to abundance of Ti-OH groups formed via anodic oxidation, but subsequent heat treatment would decrease the amount of surface hydroxyl (OH) groups and result in the loss of the apatite-forming ability.     

The influence of UV irradiation on the surface of chitosan films

The surface properties of chitosan films before and after UV-irradiation (λ = 254 nm and 248 nm, respectively) were investigated using the technique of scanning electron microscopy (SEM) and by means of contact angle measurements allowing the calculation of surface free energy. Moreover, in order to determine the film mass changes, quartz crystal microbalance (QCM) measurements were performed. Measurements of the contact angle for diiodomethane (D), formamide (F) and glycerol (G) on the surface of chitosan films were made. The chemical and structural changes during UV irradiation were studied by FTIR-ATR spectroscopy.The contact angle and the surface free energy were altered by UV irradiation of chitosan films. The microscopy images have shown that the KrF excimer laser irradiation caused visible damages on the surface in comparison with the surface exposed to the mercury UV lamp. The surface modification of chitosan films can be achieved using both, the low intensity UV lamp and the excimer laser.     

Patterning of nanoparticulate transparent conductive ITO films using UV light irradiation and UV laser beam writing

Indium tin oxide (ITO) thin film is one of the most widely used as transparent conductive electrodes in all forms of flat panel display (FPD) and microelectronic devices. Suspension of already crystalline conductive ITO nanoparticles fully dispersed in alcohol was spun, after modifying with coupling agent, on glass substrates. The low cost, simple and versatile traditional photolithography process without complication of the photoresist layer was used for patterning ITO films. Using of UV light irradiation through mask and direct UV laser beam writing resulted in an accurate linear, sharp edge and very smooth patterns. Irradiated ITO film showed a high transparency (∼85%) in the visible region. The electrical sheet resistance decrease with increasing time of exposure to UV light and UV laser. Only 5 min UV light irradiation is enough to decrease the electrical sheet resistance down to 5 kΩ□.     

Preparation of Ag-doped mesoporous titania and its enhanced photocatalytic activity under UV light irradiation

Ag-doped mesoporous titania was synthesized via a combined sol-gel process with surfactant-assisted templating method using cetyltrimethyl ammonium bromide (CTAB) as the structure-directing agent. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), N₂ adsorption-desorption measurements (BET) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activity of the samples was determined by degradation of model contaminant water of phenol in aqueous solution. Results showed that different amounts of Ag-doping had different effects on the crystal phase structure and photocatalytic activity of the samples. The sample with 0.5% Ag doping shows the highest photocatalytic activity, which is 2.3 times that of the undoped mesoporous titania.     

Degradation of white anodic-oxide coatings in UV irradiation in vacuum

Photostimulated degradation of the reflectivity of white anodic-oxide coatings on Al alloy (Al-AOCs) that are used as thermal-regulating coatings of space vehicles is investigated by spectroscopy of diffuse reflection in the region of 0.5–6 eV. It is established that irradiation in vaccum when λ≤300 nm leads to the appearance in diffuse-reflection spectra of the absorption bands at 4.0 and ∼4.6 eV that are similar to these induced by vacuum heating for T≥350 K. A growth in the absorption bands is accompanied by gas release from the coatings. These processes have a common excitation spectrum, basic kinetic regularities, and a thermoactivated character. UV irradiation in vacuum is assumed to initiate Al-AOC destruction with the formation of color centers. This process is accompanied by the desorption of molecular products. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 6, pp. 801–806, November–December, 1997.     

Comparison of self-cleaning properties of three titania coatings on float glass

This work compares the self-cleaning properties of experimental TiO₂ and TiO₂-Ag coatings on float glass with a commercial self-cleaning glass. In the experimental surfaces, TiO₂ coating was applied to float glass via the sol-gel route, while TiO₂-Ag coating was applied by the liquid flame spray method, which deposits TiO₂-Ag composite nanoparticles on the surface. The effect of the coatings on the surface wettability and the activation time for achieving hydrophilicity was studied through water contact angle as a function of exposure time to UV light. The surface morphology was investigated by using scanning electron microscopy (SEM) and confocal optical microscopy. The photocatalytic activity of the coatings was examined with methylene blue and stearic acid degradation tests. Finally, the soil attachment to the surfaces was tested with a sebum-based model soil. The sol-gel TiO₂ coating became superhydrophilic within a few hours, while the activation time needed for the commercial titania coated glass was several days. The surface with the TiO₂-Ag nanoparticles did not show any marked changes in the water contact angle. The commercial titania coated and the sol-gel TiO₂ surfaces showed self-cleaning properties and clearly lower attachment of soil than the uncoated and TiO₂-Ag coated surfaces. The difference in the interaction of the surfaces with the organic contaminants was assumed to depend mainly on differences in the thickness of the coatings.     

Characterization of vanadium-doped mesoporous titania and its adsorption of gaseous benzene

A series of vanadium-doped mesoporous titania with different metal contents was synthesized in the study via a sol-gel process with the assistance of a dodecylamine surfactant. The existence of vanadium ions not only suppressed crystallization and sintering but also enhanced the porosity of the mesoporous TiO₂. Varying the vanadium concentration led to significant changes in the chemical oxidation state of each component. The presence of metal dopants significantly improved the removal efficiency of benzene and the doping the titania with 5 mol% vanadium removed the most benzene, regardless of the adsorption temperature. The adsorption behavior was elucidated by the specific surface area, the interactions between surface hydroxyl groups and the π-electrons of benzene, and the formation of σ-bonding and d-π* back-donation between the adsorbent and organic compounds.     

Formation and structure of sphene/titania composite coatings on titanium formed by a hybrid technique of microarc oxidation and heat-treatment

Sphene/titania composite coatings were fabricated on titanium by a hybrid technique of microarc oxidation (MAO) and heat treatment. The high-applied voltages promote the formation of sphene in the MAO coatings after heat-treatment. Heat treatment could change the surface morphology of the MAO coatings such as roughness, macropores size and density and the thickness of the MAO coatings. Increasing the heat-treatment temperature decreased the atomic concentration ratios of Ti/Si and Ti/Ca of the MAO coatings. The chemical states of Ti⁴⁺, Ca²⁺, Si²⁺ and O²⁻ were observed on all the coatings. Additionally, Ti²⁺ was detected in the MAO and heat-treated MAO coatings at 600 and 700 °C. The heat-treatment has obvious effect on the chemical states of Si, Ti and O elements due to the formation of sphene and oxidation of TiO phase of the MAO coating, but did not affect that of Ca. In the heat-treated MAO coatings at 800 °C (MAO-H8), the titanium surface shows a MAO top layer and oxidized interior layer. A concentration gradient in components in the MAO layer of the MAO-H8 coating was formed.     

Formation of titania composite coatings on carbon steel by plasma electrolytic oxidation

Titania composite coatings were prepared on carbon steel by plasma electrolytic oxidation in silicate electrolyte and aluminate electrolyte with titania powers doping in the electrolytes. The microstructure of the coatings was characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The properties of the coatings including bond strength, thickness, thermal shock resistance and corrosion resistance varying with the quantities of titania powers in the electrolytes were studied. Investigation results revealed that the coating obtained in silicate electrolyte was composed of anatase-TiO₂, rutile-TiO₂ crystal phases and some Fe, Si, P elements; coating obtained in aluminate electrolyte consisted of anatase-TiO₂, Al₂TiO₅ and some Fe, P elements. Coatings obtained in two types of electrolytes show porous and rough surface. With increasing the concentration of titania powers in the electrolytes, the coating surface first became more compact and less porous and then became more porous and coarse. The bond strength and thickness were not strongly affected by concentration of titania powers in electrolytes. The valves were 23 MPa and for 66 μm for coatings obtained in aluminate electrolyte, and 21 MPa and 35 μm for coatings obtained in silicate electrolyte. Coatings obtained in silicate electrolyte showed a little better thermal shock resistance than those obtained in aluminate electrolyte and the best coatings were obtained with middle concentration of titania powers in the electrolytes. All coated samples showed better corrosion resistance than the substrate in 3.5 wt% NaCl solution. The best coatings were also obtained with middle concentration of titania powers doping in both electrolytes whose corrosion current density was decreased by 2 orders of magnitude compared with the substrate.     

Influences of ultraviolet irradiation on structure and tribological properties of diamond-like carbon films

Two types of diamond-like carbon (DLC) films with different bonding configurations were produced by pulse-assisted and DC-assisted plasma chemical vapor deposition. The chemical composition, surface morphology, microstructure, internal stress and tribological properties of the two films before and after the ultraviolet (UV) irradiation were investigated and compared. It was found that the UV irradiation had little effects on the chemical composition and surface morphology of both the films, but greatly influenced their tribological properties in the opposite trends. This result was attributed to the different changing outcomes of the bonding configuration induced by the UV actions of primary photo-dissociation and secondary recombination, wherein the inherent bonding configuration and internal stress played important roles.     

Stability and characterization of mesoporous molecular sieve using natural clay as a raw material obtained by microwave irradiation

Mesoporous molecular sieve was synthesized via microwave irradiation method, and using natural clay, sodium silicate and aluminum chloride as raw materials and cetyl trimethyl ammonium bromide (CTAB) as a template agent under alkaline condition. The samples were characterized by various analytic and spectroscopic tools such as XRD, FT-IR, TEM, TG-DSC and N₂ physical adsorption, respectively. The results show that the synthesized sample has typical mesoporous structure and exhibits good mesoporous ordering. On the other hand, the as synthesized sample after calcination at 550 °C for 10 h has a surface area of 576.0 m²/g and an average pore size of 4.83 nm. Furthermore, the synthesized mesoporous molecular sieve still exhibits good mesoporous ordering after calcination at 750 °C for 3 h or hydrothermal treatment at 100 °C for 10 days.     

Effects of proton irradiation on structure of NdFeB permanent magnets studied by X-ray diffraction and X-ray absorption fine structure

The effects of proton irradiation on the structure of NdFeB permanent magnet were investigated by X-ray diffraction and X-ray absorption fine structure (XAFS). The results reveal that proton irradiation has no effect on the long-range structure, but significantly affects the atomic local structure of the NdFeB magnet. The alignment degree of the magnet decreases and the internal stress of the lattice increases after proton irradiation. XAFS results show that the coordination number of Fe-Nd in the first neighboring coordination shell of the Fe atoms decreases and the disorder degree increases.     

Synthesis and characterization of Co (Ni or Cu)-MCM-41 mesoporous molecular sieves with different amount of metal obtained by using microwave irradiation method

Co (Ni or Cu)-MCM-41 mesoporous molecular sieves with different amount of metal were synthesized by using cetyltrimethyl ammonium bromide as a template and by a novel microwave irradiation method. These samples were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR) and N₂ physical adsorption. The experimental results show that Co (Ni or Cu)-MCM-41 mesoporous molecular sieves were successfully synthesized. When the as-synthesized samples were calcined at 550 °C for 10 h, the template was effectively removed. Under microwave irradiation condition, Co-MCM-41 mesoporous molecular sieves have specific surface areas in a range of 745.7-1188.8 m²/g and average pore sizes in a range of 2.46-2.75 nm; Ni-MCM-41 mesoporous molecular sieves have specific surface areas in a range of 625.8-1161.3 m²/g and average pore sizes of ca. 2.7 nm; Cu-MCM-41 mesoporous molecular sieves have specific surface areas in a range of 601.6-1142.9 m²/g and average pore sizes in a range of 2.46-2.76 nm. On the other hand, with increasing the introduced metal amount, the specific surface area and pore volume of the synthesized Co (Ni or Cu)-MCM-41 mesoporous molecular sieves became small, and the mesoporous ordering of the samples became poor. Under the comparable synthesis conditions, the synthesized Co-MCM-41 mesoporous molecular sieve has a bigger specific surface area and a more uniform pore distribution as compared with the synthesized Ni-MCM-41and Cu-MCM-41 mesoporous molecular sieves.     

Study of Humidity and UV Wavelength Effects on Degradation of Photo-Irradiated Polyethylene Films Using DMA

Plastic bags, mostly made of polyethylene, cause pollution as solid waste due to their nondegradable nature. Accelerated degradation, as a solution to mitigate the menace, can be achieved through moisture enhanced photolysis. This study evaluated the effect of three relative humidity environments, i.e., 25%, 40%, and 60% RH, at a constant temperature of 55°C. The effect was studied for ultraviolet (UV) irradiated and nonirradiated samples of polyethylene (PE) films processed under conventional ways. Photodegradation was initiated using ultraviolet irradiation in the ranges (200–300) nm and (300–400) nm for two hours and the effects of subsequent humidity treatment analyzed. Dynamic mechanical analysis was used to measure the dynamic storage modulus to monitor degradation. For nonirradiated samples, there was essentially no change in storage modulus at the three relative humidity environments after 550 hrs. Irradiation in the (300–400) nm range showed faster degradation than for the (200–300)nm range with the highest drop in storage modulus being 67% after 550 hrs. Raising the humidity from 25% to 40% and 60% RH resulted in 41%, 62%, and 67% drop of storage modulus, respectively, at the 550 hrs.     

Preparation and antibacterial effect of silver-hydroxyapatite/titania nanocomposite thin film on titanium

The composite which contains Ag⁺ and nanosized hydroxyapatite with TiO₂ was deposited onto titanium by dipping method. The morphology, chemical components and structures of the thin film were characterized by XRD, scanning electronic microscope (SEM) and energy dispersive X-ray analysis (EDX). Staphylococcus aureus and Escherichia coli were utilized to test the antibacterial effect. XRD results demonstrated that the films have characteristic diffraction peaks of pure HA. EDX results showed that the deposited films consisted of Ca, P, Ti, O and Ag, all of which distribute uniformly. With regard to the antibacterial effect, 98% of S. aureus and more than 99% of E. coli were killed after 24 h incubation and pictures of SEM showed obviously fewer cells on the surface with coating.     

In vitro cell irradiation systems based on 210Po alpha source: construction and characterisation

One way of studying the risk to human health of low-level radiation exposure is to make biological experiments on living cell cultures.

Two ²¹⁰Po -particle emitting devices, with 0.5 and 100 MBq activity, were designed and constructed to perform such experiments irradiating monolayers of cells. Estimates of dose rate at the cell surface were obtained from measurements by a PIPS -particle spectrometer and from calculations by the SRIM 2000, Monte Carlo charged particle transport code. Particle fluence area distributions were measured by solid state nuclear track detectors. The design and dosimetric characterisation of the devices are discussed.     

Study of Temperature and UV Wavelength Range Effects on Degradation of Photo-Irradiated Polyethylene Films Using DMA

Plastic bags mostly made of polyethylene (PE) cause pollution as solid waste due to their non-degradability nature. Initiation of a degradative process by enhanced photo-oxidation is a possible method for an accelerated degradation. This paper presents temperature treatment effects on PE films where photodegradation was initiated using ultraviolet (UV) irradiation in the ranges of 200–300 nm and 300–400 nm for 2 hr. Effects of temperature of 40°C and 55°C on non-UV-irradiated and UV-irradiated PE films processed by conventional methods were investigated and evaluated after 50 hr, 150 hr, and 350 hr of temperature exposure. The effects of UV wavelength range irradiation on the degradation were deduced. Measuring the dynamic moduli using a dynamic mechanical analyzer monitored the degradation. The decrease in average storage modulus was 62% with treatment at 55°C, higher than the 16% drop at 40°C for unirradiated samples after 350-hr exposure. Cross-linking in UV-exposed samples, characterized by an increase in dynamic modulus (stiffening), was observed followed by a reduction of storage modulus. Temperature treatment at 55°C together with 300–400-nm UV range irradiation resulted in the largest increase, i.e., 22% after 150 hr, followed by the largest reduction of storage modulus, i.e., 74.6% for a cumulative 350-hr exposure.     

紫外光表面处理对ZnO纳米粒子的晶体结构与光学性质的影响

利用溶胶凝胶法制备了ZnO纳米粒子,用紫外光照射对其进行表面处理。探讨了表面处理对ZnO纳米粒子晶体结构与光学性质的影响。结果显示：在晶体结构方面,紫外光照射会降低ZnO纳米粒子的团聚现象,缩短晶格常数,使其所受应力由压缩应力释放变为伸张应力,增大表面能,为使能量最佳化并稳定而导致ZnO纳米粒子形成再构。在光学性质方面,紫外光照射会使ZnO纳米粒子表面产生较多的氧空位,而氧空位又会使其表面容易吸附羟基,使得ZnO纳米粒子变得更加亲水。