Electrical behaviour of SiOxNy thin films and correlation with structural defects

Silicon oxynitride thin films were deposited by reactive r.f. sputtering from a silicon target. Different Ar:O₂:N₂ gas atmospheres were used at fixed power density (3.18 W cm⁻²) and pressure (0.4 Pa) to obtain various film composition. Pt-SiO_xN_y-Pt sandwich type structure was realised for electrical property investigations. The C-V measurements showed the absence of a Schottky barrier and thus confirmed that Pt electrode provides an ohmic contact. The evolution of the current density showed a decrease of the film conductivity when the oxygen concentration in the films increases. The various layer composition leads to two different conduction mechanisms which were identified as space charge limited current (SCLC) and Poole-Frenkel effect. Finally, the structural defects of the films were studied by EPR analysis and the spin densities were correlated to both the composition and the electrical behaviour of the films.     

AlNxOy thin films deposited by DC reactive magnetron sputtering

AlN_xO_y thin films were produced by DC reactive magnetron sputtering, using an atmosphere of argon and a reactive gas mixture of nitrogen and oxygen, for a wide range of partial pressures of reactive gas. During the deposition, the discharge current was kept constant and the discharge parameters were monitored. The deposition rate, chemical composition, morphology, structure and electrical resistivity of the coatings are strongly correlated with discharge parameters. Varying the reactive gas mixture partial pressure, the film properties change gradually from metallic-like films, for low reactive gas partial pressures, to stoichiometric amorphous Al₂O₃ insulator films, at high pressures. For intermediate reactive gas pressures, sub-stoichiometric AlN_xO_y films were obtained, with the electrical resistivity of the films increasing with the non-metallic/metallic ratio.     

Electrical property of HfOxNy-HfO2-HfOxNy sandwich-stack films

The effects of HfO_xN_y on the electrical property of HfO_xN_y-HfO₂-HfO_xN_y sandwich-stack (signed as SS) films were investigated. Excellent electrical performances were achieved in SS films, with a high dielectric constant of 16 and a low leakage current of ∼2 × 10⁻⁸ A/cm² at 1 MV/cm. Schottky (SK) emission and Frenkel-Poole (PF) emission are found to be the dominant mechanisms for the current conduction behavior. After a long time stress, the flat-band voltage shift in the SS film is much smaller than that in a pure HfO_xN_y film indicating fewer charge traps existed in the SS film. Based on the experiments, the new SS structure is more favorable for the improvement of electrical performances than a pure HfO_xN_y or HfO₂ structure.     

Sputter deposition of high transparent TiO2−xNx/TiO2/ZnO layers on glass for development of photocatalytic self-cleaning application

In this study, TiO_2−xN_x/TiO₂ double layers thin film was deposited on ZnO (80 nm thickness)/soda-lime glass substrate by a dc reactive magnetron sputtering. The TiO₂ film was deposited under different total gas pressures of 1 Pa, 2 Pa, and 4 Pa with constant oxygen flow rate of 0.8 sccm. Then, the deposition was continued with various nitrogen flow rates of 0.4, 0.8, and 1.2 sccm in constant total gas pressure of 4 Pa. Post annealing was performed on as-deposited films at various annealing temperatures of 400, 500, and 600 °C in air atmosphere to achieve films crystallinity. The structure and morphology of deposited films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and atomic force microscopy (AFM). The chemical composition of top layer doped by nitrogen was evaluated by X-ray photoelectron spectroscopy (XPS). Photocatalytic activity of samples was measured by degradation of Methylene Blue (MB) dye. The optical transmittance of the multilayer film was also measured using ultraviolet-visible light (UV-vis) spectrophotometer. The results showed that by nitrogen doping of a fraction (∼1/5) of TiO₂ film thickness, the optical transmittance of TiO_2−xN_x/TiO₂ film was compared with TiO₂ thin film. Deposited films showed also good photocatalytic and hydrophilicity activity at visible light.     

Characterization of HfOxNy gate dielectrics using a hafnium oxide as target

Hafnium oxynitride (HfO_xN_y) gate dielectric has been deposited on Si (1 0 0) by means of radio frequency (rf) reactive sputtering using directly a HfO₂ target in N₂/Ar ambient. The thermal stability and microstructural characteristics for the HfO_xN_y films have been investigated. XPS results confirmed that nitrogen was successfully incorporated into the HfO₂ films. XRD analyses showed that the HfO_xN_y films remain amorphous after 800 °C annealing in N₂ ambient. Meanwhile the HfO_xN_y films can also effectively suppress oxygen diffusion during high temperature annealing and prevent interface layer from forming between HfO_xN_y films and Si substrates. AFM measurements demonstrated that surface roughness of the HfO_xN_y films increase slightly as compared to those pure HfO₂ films after post deposition annealing. By virtue of building reasonable model structure, the optical properties of the HfO_xN_y films have been discussed in detail.     

Composition, microstructure, and properties of CrNx films deposited using medium frequency magnetron sputtering

CrN_x films were deposited on stainless steel and Si (1 1 1) substrates via medium frequency magnetron sputtering in a N₂ + Ar mixed atmosphere. The influence of N₂ content on the deposition rate, composition, microstructure, mechanical and tribological properties of the as-deposited films was investigated by means of the X-ray photoelectron spectrometry (XPS), X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), nanoindentation and tribometer testing. It was found that the N atomic concentration increased and the phase transformed from a mixture of Cr₂N + Cr(N) to single-phase Cr₂N, and then Cr₂N + CrN to pure CrN phase with the increase of N₂ content. The Cr 2p_3/2 and N 1s of XPS spectra also confirmed the evolution of phase. Accordingly, all films exhibited a typical columnar structure which lies in the zone T of Thornton Model. The mixed Cr₂N and Cr(N) phases showed low hardness and high friction coefficient. Cr₂N possessed higher hardness than CrN while CrN exhibited lower friction coefficient.     

Effect of nitrogen content on the properties of CrNxOyCz coating prepared by DC reactive magnetron sputtering

The CrN_xO_yC_z coatings were deposited by planar DC reactive magnetron sputtering onto AZ31 Mg alloy and high speed tool steel (HSTS) substrates at a substrate temperature of 200 °C. The effect of N₂ content on composition and structure of the CrN_xO_yC_z coatings was investigated. The structure of the CrN_xO_yC_z coatings was analyzed by a glancing angle X-ray diffraction (GXRD). The cross-section morphology and thickness of the CrN_xO_yC_z coatings were checked by a field emission scanning electron microscope (FESEM), and the composition profile and chemical state were carried out by an X-ray photoelectron spectroscopy (XPS). The experimental results showed that the structure and phase composition of the CrN_xO_yC_z coatings depended on N₂ content. The evolution of the structure of CrN_xO_yC_z coatings was consistent with CrN_x-based coatings, and the CrN_xO_yC_z coatings contained Cr₂O₃, CrO₂, CrO, Cr₃C₂, CrN_x (Cr, CrN, Cr₂N), as well as different chromium oxynitride. However, the carbide and oxynitride were oxidized after annealing.     

Preparation and characterization of CrNxOy thin films: The effect of composition and structural features on the electrical behavior

Metallic oxynitrides have attracted the attention of several researchers in the last decade due to their versatile properties. Through the addition of a small amount of oxygen into a transition metal nitride film, the material's bonding states between ionic and covalent types can be tailored, thus opening a wide range of electrical, optical, mechanical and tribological responses. Among the oxynitrides, chromium oxynitride (CrN_xO_y) has many interesting applications in different technological fields. In the present work the electrical behavior of CrN_xO_y thin films, deposited by DC reactive magnetron sputtering, were investigated and correlated with their compositional and structural properties. The reactive gas flow, gas pressure, and target potential were monitored during the deposition in order to control the chemical composition, which depend strongly on reactive sputtering process. Depending on the particular deposition parameters that were selected, it was possible to identify three types of films with different growth conditions and physical properties. The electrical resistivity of the films, measured at room temperature, was found to depend strongly on the chemical composition of the samples.     

Effect of annealing temperature on microstructure, hardness and adhesion properties of TiSixNy superhard coatings

A series of TiSi_xN_y superhard coatings with different Si contents were prepared on M42 steel substrates using two Ti and two Si targets by reactive magnetron sputtering at 500 °C. These samples were subsequently vacuum-annealed at 500, 600, 700, 800 and 900 °C, respectively. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), microindenter, Rockwell hardness tester and scratch tester were applied to investigate the microstructure, phase configuration, hardness and adhesion properties of as-deposited and annealed samples. The results indicated that there were two bonds, TiN and Si₃N₄, in all presently deposited TiSi_xN_y thin films, that structure was nanocomposite of nanocrystalline (nc-) TiN embedded into amorphous Si₃N₄ matrices. Annealing treatment below 900 °C played a little role in microstructure and hardness of the coatings although it greatly affected those of steel substrates. The film-substrate adhesion strength was slightly increased, followed by an abrupt decrease with increasing annealing temperature. Its value got to the maximum at 600 °C. Annealing had little effect on the friction coefficient with its value varying in the range of 0.39-0.40.     

Tribological development of TiCN coatings by adjusting the flowing rate of reactive gases

TiCN coatings were deposited by means of direct current magnetron sputtering of Ti targets in presence of N₂ and C₂H₂ reactive gases. The microstructure, composition, mechanical and tribological properties of the deposited thin films were analyzed by using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), nanoindentation, ball-on-disc, scratch test, and three dimensional (3D) optical microscopy. The obtained results presents a reproducible processing route for tailoring microstructure, mechanical and tribological behavior of TiCN coatings by controlling flowing rate of the reactive gases.     

Properties of MgxZn1−xO thin films sputtered in different gases

Mg_xZn_1−xO alloy films were prepared on sapphire substrates using Ar and N₂ as the sputtering gases. The effect of the sputtering gas on the structural, optical and electrical properties of the Mg_xZn_1−xO films was studied. By using N₂ as the sputtering gas, the Mg_xZn_1−xO film shows p-type conductivity and the band gap is larger than that employing Ar as the sputtering gas. The reason for this phenomenon is thought to be related to the reaction between N-O or N-Zn, and the N-doping.     

微波ECR磁控溅射制备SiNx薄膜的XPS结构研究

利用微波电子回旋共振等离子体增强非平衡磁控溅射法在不同N₂流量下制备无氢SiN_x薄膜.通过X光电子能谱、纳米硬度仪等表征技术,研究了不同N₂流量下制备的SiN_x薄膜的化学键结构、化学键含量、元素配比及各元素沿深度分布.研究结果表明,N₂流量是影响SiN_x薄膜化学键结构、元素配比、元素延深度分布等性质的主要因素.在N_{2关键词： x}')" href="#">SiN_x 磁控溅射 XPS 化学键结构     

Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy

Composite coatings using pure Al powder blended with α-Al₂O₃ as feedstock were deposited on AZ91D magnesium alloy substrates by cold spray (CS). The content of α-Al₂O₃ in the feedstock was 25 wt.% and 50 wt.%, respectively. The effects of α-Al₂O₃ on the porosity, microhardness, adhesion and tensile strength of the coatings were studied. Electrochemical tests were carried out in neutral 3.5 wt.% NaCl solution to evaluate the effect of α-Al₂O₃ on the corrosion behavior of the coatings. The results showed that the composite coatings possessed lower porosity, higher adhesion strength and tensile strength than cold sprayed pure Al coating. The corrosion current densities of the composite coatings were similar to that of the pure Al coating and much higher than that of bare AZ91D magnesium alloy.     

Pulsed laser ablation of zinc selenide in nitrogen ambience: Formation of zinc nitride films

Zinc nitride (Zn₃N₂) thin films are prepared using pulsed laser deposition (PLD) from zinc selenide (ZnSe) target at different nitrogen ambient pressures viz. 1, 3, 5, 7 and 10 Pa. The films prepared with nitrogen pressures 1 and 3 Pa are amorphous in nature, whereas the films prepared at 5, 7 and 10 Pa exhibit the presence of cubic bixbyite Zn₃N₂ structure with lattice parameter very close to bulk of Zn₃N₂. The particle size calculated by Debye Scherrer's formula is in the nano regime. Surface morphology of the films is studied by SEM and AFM analysis. Optical parameters such as band gap, refractive index and porosity of the films are calculated. Moreover, the present study confers an outlook about how do various factors such as substrate temperature, reactive supplementing gas and laser-target interaction influence the film developing process during pulsed lased deposition.     

Ellipsometric study of a-Be3N2 thin films prepared by radio frequency magnetron sputtering

The ellipsometric characterizations of amorphous beryllium nitride (a-Be₃N₂) thin films deposited on Si (1 0 0) and quartz at temperature <50 °C using reactive RF sputtering deposition were examined in the wavelength range 280-1600 nm. X-ray diffraction of the films showed no structure, suggesting the Be₃N₂ films grown on the substrates are amorphous. The composition and chemical structures of the amorphous thin films were determined by using electron spectroscopy for chemical analysis. The surface morphology of a-Be₃N₂ was characterized by atomic force microscopy. The thicknesses and optical constants of the films were derived from spectroscopic ellipsometry measurements. The variation of the optical constants with thickness of the deposited films has been investigated. From the angle dependence of the polarized reflectivity we deduced a Brewster angle of 64°. At any angle of incidence, the a-Be₃N₂ shown high transmissivity (80-99%) and low reflectivity (<18%) in the visible and near infrared regions. Hence, the a-Be₃N₂ could be a good candidate for antireflection optical coatings under conditions of optimized the type of polarization and the angle of incidence.     

Mechanical, tribological, and electrochemical behavior of Cr1−xAlxN coatings deposited by r.f. reactive magnetron co-sputtering method

Chromium aluminum nitride (Cr_1−xAl_xN) coatings were deposited onto AISI H13 steel and silicon substrates by r.f. reactive magnetron co-sputtering in (Ar/N₂) gas mixture from chromium and aluminum targets. Properties of deposited Cr_1−xAl_xN coatings such as compositional, structural, morphological, electrochemical, mechanical and tribological, were investigated as functions of aluminum content. X-ray diffraction patterns of Cr_1−xAl_xN coatings with different atomic concentrations of aluminum (0.51 < x < 0.69) showed the presence and evolution of (1 1 1), (2 0 0), and (1 0 2) crystallographic orientations associated to the Cr_1−xAl_xN cubic and w-AlN phases, respectively. The rate of corrosion of the steel coated with Cr_1−xAl_xN varied with the applied power; however, always being clearly lower when compared to the uncoated substrate. The behavior of the protective effect of the Cr_1−xAl_xN coatings is based on the substitution of Cr for Al, when the power applied to the aluminum target increases. The mechanical properties were also sensitive to the power applied, leading to a maximum in hardness and a reduced elastic modulus of 30 and 303 GPa at 350 W and a monotonic decrease to 11 and 212 GPa at 450 W, respectively. Finally, the friction coefficient measured by pin-on disk revealed values between 0.45 and 0.70 in humid atmosphere.     

Effect of argon ion activity on the properties of Y2O3 thin films deposited by low pressure PACVD

Yttrium oxide thin films are deposited by microwave electron cyclotron resonance (ECR) plasma assisted metal organic chemical vapour deposition process using an indegeneously developed Y(thd)₃ {(2,2,6,6-tetramethyl-3,5-heptanedionate)yttrium} precursor. Depositions were carried out at two different argon gas flow rates keeping precursor and oxygen gas flow rate constant. The deposited coatings are characterized by X-ray photoelectron spectroscopy (XPS), glancing angle X-ray diffraction (GIXRD) and infrared spectroscopy. Optical properties of the films are studied by spectroscopic ellipsometry. Hardness and elastic modulus of the films are measured by load depth sensing nanoindentation technique. Stability of the film and its adhesion with the substrate is inferred from the nanoscratch test.It is shown here that, the change in the argon gas flow rates changes the ionization of the gas in the microwave ECR plasma and imposes a drastic change in the characteristics like composition, structure as well as mechanical properties of the deposited film.     

Effect of oxidation temperature on microstructure, mechanical behaviors and surface morphology of nanocomposite Ti-Cx-Ny thin films

Two nanocomposite Ti-C_x-N_y thin films, TiC_0.95N_0.60 and TiC_2.35N_0.68, as well as one pure TiN, were deposited at 500 °C on Si(1 0 0) substrate by reactive unbalanced dc-magnetron sputtering. Oxidation experiments of these films were carried out in air at fixed temperatures in a regime of 250-600 °C with an interval of 50 °C. As-deposited and oxidized films were characterized and analyzed using X-ray diffraction (XRD), microindentation, Newton's ring methods and atomic force microscopy (AFM). It was found that the starting oxidation temperature of nanocomposite Ti-C_x-N_y thin films was 300 °C irrespective of the carbon content; however their oxidation rate strongly depended on their carbon content. Higher carbon content caused more serious oxidation. After oxidation, the film hardness value remained up to the starting oxidation temperature, followed by fast decrease with increasing heating temperature. The residual compressive stress did not show a similar trend with the hardness. Its value was first increased with increase of heating temperature, and got its maximum at the starting oxidation temperature. A decrease in residual stress was followed when heating temperature was further increased. The film surface roughness value was slightly increased with heating temperature till the starting oxidation temperature, a great decrease in surface roughness was followed with further increase of heating temperature.     

Preparation and annealing study of TaNx coatings on WC-Co substrates

To prevent Co diffusion from cemented carbides at high temperatures, we fabricated TaN_x coatings by reactive direct current (d.c.) magnetron sputtering onto 6 wt.% cobalt cemented carbide substrates, to form diffusion barrier layers. Varying the nitrogen flow ratio, N₂/(Ar + N₂), from 0.05 to 0.4 during the sputtering process had a significant effect on coating structure and content. Deposition rate reduced as the nitrogen flow ratio increased. The effects of nitrogen flow ratio on the crystalline characteristics of the TaN_x coatings were examined by X-ray diffraction. The TaN_x coatings annealing conditions were 500, 600, 700, and 800 °C for 4 h in air. We evaluated the performance of the diffusion barrier using both Auger electron spectroscopy depth-profiles and X-ray diffraction techniques. We also investigated oxidation resistance of the TaN_x coatings annealed in air, and under a 50 ppm O₂-N₂ atmosphere, to evaluate the fabricated layers effectiveness as a protective coating for glass molding dies.     

Composition of Ta2O5 stacked films on N2O- and NH3-nitrided Si

The composition and microstructure of rf sputtered 20 nm Ta₂O₅ on N₂O or NH₃ Rapid Thermal Nitrided (RTN) Si substrates have been investigated by X-ray photoelectron spectroscopy. RTN at 800 and 850 °C is effective to suppress active oxidation of Si. There is no evidence for the presence of SiO₂ at Si interface. A lightly nitrided surface is established in both cases without a formation of detectable oxynitride layer at Si. A layered nature of the films is observed, with stoichiometric tantalum pentoxide at and close to the films’ surface. In the depth, the films are mixed ones whose composition depends on the nitridation ambient. N₂O treatment stimulates oxidation processes during the film deposition while NH₃ nitridation results to a less effective oxidation and produces Ta-silicate like film. The correlation between the composition of the interfacial regions and the nitridation gas is also discussed. The results suggest that hydrogen, as a component of nitridation ambient, plays significant role in the reactions controlling the exact composition of the deposited Ta₂O₅, activating reactions with nitrogen. Nitrogen related reactions likely occur with NH₃ processing but do not with N₂O one. The presence of nitrogen feature is not detected in N₂O-samples spectra at all. In the integration perspective, preliminary RTN of Si in N₂O or NH₃ could be a suitable way to produce layered Ta₂O₅-based films with more or less presence of tantalum silicate with a trace of nitrogen, either only at the interface with Si (N₂O-process) or in the whole film (NH₃-process).