Morphological and chemical study of the initial growth of CdS thin films deposited using an ammonia-free chemical process

We study the initial growth stages of CdS thin films deposited by an ammonia-free chemical bath deposition process. This ammonia-free process is more environmentally benign because it reduces potential ammonia release to the environment due to its high volatility. Instead of ammonia, sodium citrate was used as the complexing agent. We used atomic force microscopy (AFM), Rutherford backscattering (RBS) and X-ray photoelectron spectroscopy (XPS) to investigate the morphological and chemical modifications at the substrate surface during the first initial stages of the CdS deposition process. Additionally, X-ray diffraction (XRD) and optical transmission spectroscopy measurements were carried out to compliment the study. XPS results show that the first nucleation centers are composed by Cd(OH)₂ which agglomerate in patterns of bands, as demonstrated by AFM results. It is also observed that the conversion to CdS (by anionic exchange) of the first nucleus begins before the substrate surface is completely covered by a homogenous film.     

On the structure, morphology, and optical properties of chemical bath deposited Sb2S3 thin films

In the present paper, we have reported the room temperature growth of antimony sulphide (Sb₂S₃) thin films by chemical bath deposition and detailed characterization of these films. The films were deposited from a chemical bath containing SbCl₃ and Na₂S₂O₃ at 27 °C. We have analysed the structure, morphology, composition and optical properties of as deposited Sb₂S₃ films as well as those subjected to annealing in nitrogen atmosphere or in air. As-deposited films are amorphous to X-ray diffraction (XRD). However, the diffused rings in the electron diffraction pattern revealed the existence of nanocrystalline grains in these films. XRD analysis showed that upon annealing in nitrogen atmosphere these films transformed into polycrystalline with orthorhombic structure. Also, we have observed that during heating in air, Sb₂S₃ first converts into orthorhombic form and then further heating results in the formation of Sb₂O₃ crystallites. Optical bandgap energy of as deposited and annealed films was evaluated from UV-vis absorption spectra. The values obtained were 2.57 and 1.73 eV for the as-deposited and the annealed films respectively.     

Properties of In2S3 thin films deposited onto ITO/glass substrates by chemical bath deposition

In₂S₃ films have been chemically deposited on ITO coated glass substrates by chemical bath deposition, using different deposition times and precursor concentrations. The bilayers are intended for photovoltaic applications. Different characterization methods have been employed: optical properties of the films were investigated from transmittance measurements, structural properties by XRD and micro-Raman, and surface morphology by SEM microscopy analysis. Also, the direct and indirect band-gaps and the surface gap states were studied with surface photovoltage spectroscopy (SPS). We proposed that electronic properties of the In₂S₃ samples are controlled by two features: shallow tail states and a broad band centred at 1.5 eV approximately. Their relation with the structure is discussed, suggesting that their origin is related to defects created on the S sub-lattice, and then both defects are intrinsic to the material.     

Effect of [Zn]/[S] ratios on the properties of chemical bath deposited zinc sulfide thin films

ZnS thin films have been prepared by chemical bath deposition (CBD) technique onto glass substrates deposited at about 80 °C using aqueous solution of zinc sulfate hepta-hydrate, ammonium sulfate, thiourea, ammonia and hydrazine hydrate. Ammonia and hydrazine hydrate were used as complexing agents. The influence of the ratio of [Zn]/[S] on formation and properties of ZnS thin films has been investigated. The ratio of [Zn]/[S] was changed from 3:1 to 1:9 by varying volumes and/or concentrations of zinc sulfate hepta-hydrate and thiourea in the deposition solution. The structural and morphological characteristics of films have been investigated by X-ray diffraction (XRD), scanning electron microscope and UV-vis spectroscopic analysis. ZnS films were obtained with the [Zn]/[S] ratio ranged from1:1 to 1:6. In the cases of [Zn]/[S] ratio ≥ 3:1 or ≤1:9, no deposition was found. Transparent and polycrystalline ZnS film was obtained with pure-wurtzite structure at the [S]/[Zn] ratio of 1:6. The related formation mechanisms of CBD ZnS are discussed. The deposited ZnS films show good optical transmission (80-90%) in the visible region and the band gap is found to be in the range of 3.65-3.74 eV. The result is useful to further develop the CBD ZnS technology.     

Properties of ZnO thin films deposited on (glass,ITO and ZnO:Al) substrates

ZnO thin films were deposited on glass, ITO (In₂O₃; Sn) and on ZnO:Al coated glass by spray pyrolysis. The substrates were heated at 350 °C. Structural characterization by X-ray diffraction (XRD) measurements shows that films crystallize in hexagonal structure with a preferential orientation along (0 0 2) direction. XRD peak-shift analysis revealed that films deposited on glass substrate (−0.173) were compressive, however, films deposited onto ITO (0.691) and on ZnO:Al (0.345) were tensile. Scanning electron microscopies (SEM) show that the morphologies of surface are porous in the form of nanopillars. The transmittance spectra indicated that the films of ZnO/ITO/glass and ZnO/ZnO:Al/glass exhibit a transmittance around 80% in the visible region. An empirical relationship modeled by theoretical numerical models has been presented for estimating refractive indices (n) relative to energy gap. All models indicate that the refractive index deceases with increasing energy band gap (E_g).     

Synthesis, characterization and photoelectrochemical properties of n-CdS thin films

Cadmium sulfide thin films have been deposited on glass substrates by simple and cost effective chemical bath deposition technique. Triethanolamine was used as a complexing agent. The preparative parameters like ion concentration, temperature, pH, speed of substrate rotation and deposition time have been optimized for good quality thin films. The ‘as-grown’ films are characterized for structural, electrical, optical and photoelectrochemical (PEC) properties. The X-ray diffraction (XRD) studies reveal that the films are polycrystalline in nature. Energy-dispersive analysis by X-ray (EDAX) shows that films are cadmium rich. Uniform deposition of CdS thin films on glass substrate is observed from scanning electron microscopy (SEM) and atomic force microscopy (AFM) micrographs. Optical studies reveal a high absorption coefficient (10⁴ cm⁻¹) with a direct type of transition. The band gap is estimated to be 2.47 eV. The film shows n-type conduction mechanism. The photoelectrochemical (PEC) cell with CdS thin film as a photoanode and sulfide/polysulfide (1 M) solution as an electrolyte have been constructed and investigated for various cell parameters. The solar to electrical conversion efficiency (η) and fill factor (ff) are found to be 0.049% and 0.36, respectively.     

Observations on the influence of pH control on the properties of chemically deposited CdS films in an ammonia-free system

In this work we report on the properties of chemically deposited CdS thin films in an ammonia-free cadmium-sodium citrate system. We studied the influence on the properties of the films of the pH control of the reaction solution. For this, we deposited two types of CdS films employing two different types of reaction solutions. The only difference between both reaction solutions was the addition of a pH buffer in one of them in order to control its pH throughout the deposition process. Several sets of CdS films were deposited from growth solutions with different contents of Cd to determine also the influence of this parameter on the properties of the films. The CdS films were studied by X-ray diffraction, optical transmission and reflection spectroscopy and scanning electron microscopy measurements. We found that the properties of the films depend both on the amount of Cd in the growth solutions and on their pH control. The increase in Cd in the reaction solution yields to films with shorter lattice constant and then higher energy band gap. On the other hand, the pH control of the reaction produces higher deposition rate, larger final thickness and higher energy band gaps in the CdS films.     

Physical properties of ZnSe thin films deposited on glass and silicon substrates

ZnSe thin films were deposited onto Corning glass and silicon substrates using thermal evaporation. The samples were prepared at different substrate temperatures. The thin films’ surface chemical composition was determined through Auger electron spectroscopy (AES). AES signals corresponding to Zn and Se were only detected in AES spectra. The samples’ crystallographic structure was studied through X-ray diffraction. The material crystallised in the cubic structure with preferential orientation (111). Optical properties of the ZnSe films were studied over two energy ranges via electron energy loss spectroscopy (10–90 eV) and spectral transmittance measurements (0.4–4 eV). In both cases, the spectral variation of the refractive index and the absorption coefficient were determined by fitting the experimental results with well-established theoretical models. Experimental values for the material’s gap were also found, and photoconductivity (PC) measurements were carried out. Transitions between bands, usually labelled Γ^V₈ → Γ^C₆ and Γ^V₇ → Γ^C₆, were found in the optical and PC responses. A wide spectral photoconductive response between 300 and 850 nm was found in the ZnSe/Si samples prepared at 250 °C substrate temperature.     

Effect of deposition time on structural, electrical, and optical properties of SnS thin films deposited by chemical bath deposition

The effect of deposition time on the structural, electrical and optical properties of SnS thin films deposited by chemical bath deposition onto glass substrates with different deposition times (2, 4, 6, 8 and 10 h) at 60 °C were investigated. The obtained films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and optical absorption spectra. All deposited films were polycrystalline and had orthorhombic structure with small crystal grains. Their microstructures had changed with deposition time, and their compositions were nearly stoichiometric. Electrical parameters such as resistivity and type of electrical conduction were determined from the Hall Effect measurements. Hall Effect measurements show that obtained films have p-type conductivity and resistivity values of SnS films have changed with deposition time. For allowed direct, allowed indirect, forbidden direct and forbidden indirect transitions, band gap values varied in the range 1.30-1.97 eV, 0.83-1.36 eV, 0.93-1.49 eV and 0.62-1.23 eV, respectively.     

Study of reactions between HfO2 and Si in thin films with precise identification of chemical states by XPS

Reactions between HfO₂ and Si in HfSiO films during deposition and post-annealing have been studied. Intermixing of HfO₂ and Si is achieved by radio frequency sputtering with HfO₂/Si compound targets, and post-annealing is used to promote the reaction at different temperatures. The structural characteristics of the mixture, HfSiO films, are analyzed by X-ray photoelectron spectroscopy and X-ray diffraction, and a careful assessment of chemical states is performed for precise identification. XPS results show that with ratios of Si:Hf ranging from 0 to 0.3 in HfSiO films, Si fully reacts with HfO₂ to form silicate during deposition. However, SiO₂ appears when the ratio of Si:Hf rises to 1.2. When the annealing temperature reaches 600 °C, decomposition of hafnium silicate is observed and hafnium silicide forms in the bulk of the films. XRD results reveal that HfSiO films remain amorphous with the annealing temperature below 600 °C but crystallize at 800 °C.     

Effect of freon flow rate on tin oxide thin films deposited by chemical vapor deposition

High quality fluorine-doped tin oxide (SnO₂:F) films on glass substrates were been prepared using chemical vapor deposition (CVD) method. The electrical properties, surface morphologies, structural properties and optical properties of the films were studied by varying the freon flow rates. The structure was analyzed by X-ray diffraction (XRD). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to study the morphology. Energy-dispersive spectroscopy (EDS) was conducted to understand the surface fluorine composition of the film. The results showed that crystalline structure of the film had a have cassiterite-like diffraction patterns with a preferred orientation of (1 1 0). Surface roughness was evaluated by atomic force microscopy, characterized by root mean square (RMS) and average value (Ra). The SnO₂:F resistivity decreased as the freon flow rate increased. The films had a uniform thickness and a transmittance of 80–90% within the visible region of the spectrum.     

Effect of precursor concentration and bath temperature on the growth of chemical bath deposited tin sulphide thin films

SnS is a promising candidate for a low-cost, non-toxic solar cell absorber layer. Tin sulphide thin films have been deposited by chemical bath deposition technique from a solution containing stannous chloride, thioacetamide, ammonia and triethanolamine (TEA). The effects of concentration of tin salt, triethanolamine and bath temperature on the growth of tin sulphide films have been investigated in order to optimize the growth conditions to obtain tin monosulphide (SnS) films. SnS films obtained under optimized conditions were found to be polycrystalline in nature with orthorhombic structure. The optical band gap of these films was found to be 1.5 eV.     

Effect of Al incorporation on the structural,morphological, optoelectronic and transport properties of PbS thin films

Doping of PbS thin films with different metal atoms produce considerable changes in structural and material properties that make them useful in the technology of thin film devices. The goal of this work is to study the effects of doping on the structural, morphological, optoelectronic and transport properties of PbS thin films as a function of Al³⁺ concentration. Thin films of pure and Al doped PbS nanoparticles are prepared on soda lime glass substrates by chemical bath deposition technique. The Al content in aqueous solution is varied from 0 to 20 mg. XRD analysis of the films revealed significant enhancement in crystallinity and crystallite size up to an optimum concentration of doping. Films are polycrystalline with crystallite size 19–32 nm, having face centered cubic structure. The optical band gap energy exhibits a decreasing trend and is shifted from 2.41 to 1.34 eV with increasing Al content. The room temperature conductivity of the as-deposited PbS films is in the range of 0.78×10⁻⁸ to 0.67×10⁻⁶(Ω cm)⁻¹ with a maximum for optimum Al content. The Al doped PbS thin film, which we synthesize with optimum Al concentration of 15 mg is found to be a most suitable material for solar control coating applications.     

Composition depth profiles of Bi3.15Nd0.85Ti3O12 thin films studied by X-ray photoelectron spectroscopy

In the present work, X-ray photoelectron spectroscopy (XPS) was used to investigate the composition depth profiles of Bi_3.15Nd_0.85Ti₃O₁₂ (BNT) ferroelectric thin film, which was prepared on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by chemical solution deposition (CSD). It is shown that there are three distinct regions formed in BNT film, which are surface layer, bulk film and interface layer. The surface of film is found to consist of one outermost Bi-rich region. High resolution spectra of the O 1s peak in the surface can be decomposed into two components of metallic oxide oxygen and surface adsorbed oxygen. The distribution of component elements is nearly uniform within the bulk film. In the bulk film, high resolution XPS spectra of O 1s, Bi 4f, Nd 3d, Ti 2p are in agreement with the element chemical states of the BNT system. The interfacial layer is formed through the interdiffusion between the BNT film and Pt electrode. In addition, the Ar⁺-ion sputtering changes lots of Bi³⁺ ions into Bi⁰ due to weak Bi-O bond and high etching energy.     

Influence of Si substrate preparation on surface chemistry and morphology of L-CVD SnO2 thin films studied by XPS and AFM

Results of experimental studies of the influence of substrate preparation on the surface chemistry and surface morphology of the laser-assisted chemical vapour deposition (L-CVD) SnO₂ thin films are presented in this paper. The native Si(1 0 0) substrate cleaned by UHV thermal annealing (TA) as well as thermally oxidized Si(1 0 0) substrate cleaned by ion bombardment (IBA) have been used as the substrates. X-ray photoemission spectroscopy (XPS) has been used for the control of surface chemistry of the substrates as well as of deposited films. Atomic force microscopy (AFM) has been used to control the surface morphology of the L-CVD SnO₂ thin films deposited on differently prepared substrates. Our XPS shows that the L-CVD SnO₂ thin films deposited on thermally oxidized Si(1 0 0) substrate after cleaning with ion bombardment exhibit the same stoichiometry, i.e. ratio [O]/[Sn] = 1.30 as that of the layers deposited on Si(1 0 0) substrate previously cleaned by UHV prolonged heating. AFM shows that L-CVD SnO₂ thin films deposited on thermally oxidized Si(1 0 0) substrate after cleaning with ion bombardment exhibit evidently increasing rough surface topography with respect to roughness, grain size range and maximum grain height as the L-CVD SnO₂ thin films deposited on atomically clean Si substrate at the same surface chemistry (nonstoichiometry) reflect the higher substrate roughness after cleaning with ion bombardment.     

Sol-gel synthesis, characterization and optical properties of mercury-doped TiO2 thin films deposited on ITO glass substrates

The Hg-doped and undoped nano-crystalline TiO₂ films on ITO glass substrates surface and polycrystalline powders were prepared by sol-gel dip coating technique. The crystal structure and surface morphology of TiO₂ were characterized by means of X-ray diffractometer (XRD), atomic force microscope (AFM), spectrophotometer, Fourier-transform infrared (FTIR), and spectroscopic ellipsometry (SE). The results indicated that the powder of TiO₂, doped with 5% Hg in room temperature was only composed of the anatase phase whereas in the undoped powder exhibits an amorphous phase were present. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 400 °C. The average crystallite size of the undoped TiO₂ films was about 8.17 nm and was increased with Hg-doping in the TiO₂ films. Moreover, the grains distributed more uniform and the surface roughness was greater in the Hg-doped TiO₂ films than in the undoped one. Refractive index and porosity were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range (1.95-2.49) and the porosity is in the range (47-2.8). The coefficient of transmission varies from 60 to 90%. SE study was used to determine the annealing temperature effect on the optical properties in the wavelength range from 0.25 to 2 μm and the optical gap of the Hg-doped TiO₂ thin films.     

Preparation of p-type CdS thin films and in situ dark conductivity in vacuum deposited CdS:Cu films

CdS:Cu thin films were prepared using a vacuum co-evaporation technique. The Hall measurements indicate that the conductivity characteristic of CdS thin films transformed from highly compensated in as-grown or weakly annealed materials to p-type conductive in strongly annealed materials. X-ray diffraction spectra show that as-deposited thin films were the hexagonal phase of CdS except the presence of copper for high Cu doping and the diffraction peaks of Cu disappeared after annealing. From the X-ray photoelectron spectroscopy we found the ionization of Cu atoms and the formation of an acceptor level. In situ dark conductivity in vacuum as-deposited CdS:Cu was performed in the temperature range between 27 and 250 °C. An abnormal temperature dependence of conductivity was observed in medium and heavily Cu-doped films. The formation of a p-type material at a certain temperature was also studied by the hot probe measurements, which indicates a complex compensation process in the Cu-doped CdS films.     

不同衬底和CdCl2退火对磁控溅射CdS薄膜性能的影响

在科宁7059玻璃, FTO, ITO, AZO四种衬底上磁控溅射CdS薄膜, 并在CdCl₂+干燥空气380 ℃退火, 分别研究了不同衬底和退火工艺对CdS薄膜形貌、结构和光学性能的影响. 扫描电子显微镜形貌表明: 不同衬底原位溅射CdS薄膜的形貌不同, 退火后相应CdS薄膜的晶粒度和表面粗糙度明显增大. XRD衍射图谱表明: 不同衬底原位溅射和退火CdS薄膜均为六角相和立方相的混相结构, 退火前后科宁7059玻璃, FTO, AZO衬底上CdS薄膜有 H(002)/C(111) 最强衍射峰, ITO衬底原位溅射CdS薄膜没有明显的最强衍射峰, 退火后出现 H(002)/(111) 最强衍射峰. 紫外-可见分光光度计分析表明: AZO, FTO, ITO, 科宁7059玻璃衬底CdS薄膜的可见光平均透过率依次减小, 退火后相应衬底CdS薄膜的可见光平均透过率增大, 光学吸收系数降低; 退火显著增大了不同衬底CdS薄膜的光学带隙. 分析得出: 上述结果是由于不同衬底类型和退火工艺对CdS多晶薄膜的形貌、结构和带尾态掺杂浓度改变的结果. 关键词： CdS薄膜 磁控溅射 退火再结晶 带尾态     

Influence of air annealing on the structural, morphological, optical and electrical properties of chemically deposited ZnSe thin films

Zinc selenide nanocrystalline thin films are grown onto amorphous glass substrate from an aqueous alkaline medium, using chemical bath deposition (CBD) method. The ZnSe thin films are annealed in air for 4 h at various temperatures and characterized by structural, morphological, optical and electrical properties. The as-deposited ZnSe film grew with nanocrystalline cubic phase alongwith some amorphous phase present in it. After annealing metastable nanocrystalline cubic phase was transformed into stable polycrystalline hexagonal phase with partial conversion of ZnSe into ZnO. The optical band gap, E_g, of as-deposited film is 2.85 eV and electrical resistivity of the order of 10⁶-10⁷ Ω cm. Depending upon annealing temperature, decrease up to 0.15 eV and 10² Ω cm were observed in the optical band gap, E_g, and electrical resistivity, respectively.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.