Determination of the nanoscale dielectric properties in ferroelectric lead zirconate titanate (PZT) thin films

We report on nanoscale experiments with <100 nm lateral resolution being able to differentiate the effective dielectric polarisation P_z, deposited charge density σ, surface dielectric constant ε_surface, its voltage dependence ε_surface(U), as well as the built-in electric bias voltage U_int in ferroelectric lead zirconate titanate (PZT) thin films. This is possible by combining piezoresponse force microscopy (PFM) and pull-off force spectroscopy (PFS), both methods based on scanning force microscopy (SFM). The differentiation becomes possible since both P_z and σ contribute additively in PFS, while they are subtractive in PFM, hence allowing the two contributions to be separated. ε_surface can be quantified by means of the experimental PFS data and the calculated effective penetration depth of PFM developed in a finite element modelling. Finally, U_int and ε_surface(U) are derived by an absolute matching of the P_z values measured by PFM and PFS.Our nanoscale results obtained on PZT thin films reveal values for the above specified quantities that have the same order of magnitude as those obtained from macroscopic measurements reflecting the integral response using large electrode areas. However, we stress that the data reported here reveal physical properties deduced on the nanometer scale. Furthermore, they are recorded during one single experimental investigation, using one single set-up only.     

Comparison of the effect of PLT and PZT buffer layers on PZT thin films for ferroelectric materials applications

In order to study the effect of different buffer layers on the Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films, 10-nm thick (Pb_0.72La_0.28)Ti_0.93O₃ (PLT) and Pb(Zr_0.52Ti_0.48)O₃ buffer layers have been deposited on the Pt(1 1 1)/Ti/SiO₂/Si substrates by pulsed laser deposition, respectively. The top buffer layers were also deposited on PZT thin films with the same thickness of the seed layers in order to enhance the fatigue characteristics of PZT thin films. We compared the results of dielectric constant, hysteresis loops and fatigue resistance characteristics. It was found that the dielectric properties of PZT thin films with PLT buffer layers were improved by comparing with PZT thin films with PZT buffer layers. The polarization characteristics of PZT thin films with PLT buffer layers were observed to be superior to those of PZT thin films using PZT buffer layers. The remanent polarization of PZT thin films showed 36.3 μC/cm² and 2.6 μC/cm² each in the case of use PLT and PZT buffer layers. For the switching polarization endurance analysis, PZT thin films with PLT buffer layers showed more excellent result than that of PZT thin films with PZT buffer layers.     

PZT铁电薄膜纳米尺度畴结构的扫描力显微术研究

利用扫描力显微术中压电响应模式原位研究了（111）择优取向的PZT60/40铁电薄膜的纳米尺度畴结构及其极化反转行为.铁电畴图像复杂的畴衬度与晶粒中的畴排列和晶粒的取向密切相关.直接观察到极化反转期间所形成的小至30nm宽的台阶结构，该台阶结构揭示了（111）取向的PZT60/40铁电薄膜在极化反转期间其畴成核与生长机理主要表现为铁电畴的纵向生长机理. 关键词： 畴结构 反转机理 PZT薄膜 扫描力显微术     

Polarization modification of PZT thin films by means of electric fields and stress in scanning force microscopy

Polarization switching in scanning force microscopy (SFM) is influenced by both electric fields and stress, whereby the latter can arise inherently from Maxwell stress. We discuss the influence of electric charges and of the polarization asymmetry on the switching behaviour. For single crystallites of PZT(53/47) thin films, the sectors for ferroelectric, ferroelastoelectric and ferroelastic switching are represented in a field-stress map. The influence of stress on the second harmonic of the SFM is also discussed.     

Changes in the optical properties of as-deposited plasma polymerized 2,6-diethylaniline thin films by iodine doping

In this study, plasma polymerized 2, 6-diethylaniline (PPDEA) thin films of different thicknesses were synthesized using a glow discharge plasma polymerization method. Scanning electron microscopy showed that the surface morphology of an as-deposited PPDEA thin film was comparatively smooth after iodine doping. The iodine-doped PPDEA was found to be thermally stable up to ca about 560 K, which was slightly lower than that observed for as-deposited PPDEA. Ultraviolet-visible spectroscopic analyses demonstrated that iodine doping resulted in a significant decrease in the optical energy gap. As the doping period increased, the direct optical transition energy gap was reduced from 3.56 to 2.79 eV and the indirect optical transition energy gap was decreased from 2.23 to 1.97 eV. Thus it is observed that, the optical parameters of as-deposited PPDEA thin films with different thicknesses can be modified with different iodine doping periods.     

Phase evolution and effect of pre-heating temperature on the characteristics of PZT thin films grown by using a triol sol--gel route

Lead zirconate titanate (PZT) films were fabricated on Pt(111)/Ti/SiO₂/Si(100) using the triol sol--gel method. The effect of the pre-heating temperature on the phase transformations, microstructures, electrical properties and ferroelectric properties of the PZT thin films was investigated. Randomly-oriented PZT thin films pre-heated at 400°C for 10?min and annealed at 600°C for 30?min showed well-defined ferroelectric hysteresis loops with a remanent polarization of 26.57?µC?cm^?2 and a coercive field of 115.42?kV?cm^?1. The dielectric constant and dielectric loss of the PZT films were 621 and 0.0395, respectively. The microstructures of the thin films are dense, crack-free and homogeneous with fine grains about 15–20?nm in size.     

Synthesis and characterization of ZnO thin films by thermal evaporation

ZnO thin films have been successfully synthesized by thermal evaporation of pure zinc at 900 °C under the flow of different percentages of argon and oxygen gases. The films were characterized by X-ray diffraction (XRD), variable pressure scanning electron microscopy (VPSEM), energy dispersive X-ray spectroscopy (EDS) and UV–vis spectroscopy. The aim of this paper is to study the influence of the oxygen percentage on the structural and morphological properties of the ZnO films. VPSEM results show that very thick needle structures were produced at high oxygen percentages. EDS results revealed that only Zn and O are present in the sample, indicating a composition of pure ZnO. XRD results showed that the ZnO synthesized under different quantities of oxygen were crystalline with the hexagonal wurtzite structure. UV–vis spectroscopy results indicated that the optical band gap energies from the transmission spectrum are between 3.62 and 3.69 eV for ZnO thin films.     

Influence of oxygen partial pressure on the properties of pulsed laser deposited nanocrystalline zirconia thin films

ZrO₂ thin films were deposited at various oxygen partial pressures (2.0 × 10⁻⁵-3.5 × 10⁻¹ mbar) at 973 K on (1 0 0) silicon and quartz substrates by pulsed laser deposition. The influence of oxygen partial pressure on structure, surface morphology and optical properties of the films were investigated. X-ray diffraction results indicated that the films are polycrystalline containing both monoclinic and tetragonal phases. The films prepared in the oxygen partial pressures range 2.0 × 10⁻⁵-3.5 × 10⁻¹ mbar contain nanocrystals of sizes in the range 54-31 nm for tetragonal phase. The peak intensity of the tetragonal phase decreases with the increase of oxygen partial pressures. Surface morphology of the films examined by AFM shows the formation of nanostructures. The RMS surface roughness of the film prepared at 2.0 × 10⁻⁵ mbar is 1.3 nm while it is 3.2 nm at 3.5 × 10⁻¹ mbar. The optical properties of the films were investigated using UV-visible spectroscopy technique in the wavelength range of 200-800 nm. The refractive index is found to decrease from 2.26 to 1.87 as the oxygen partial pressure increases from 2.0 × 10⁻⁵ to 3.5 × 10⁻¹ mbar. The optical studies show two different absorption edges corresponding to monoclinic and tetragonal phases.     

化学水浴法和磁控溅射法制备硫化镉薄膜的性能研究

以氯化铵、氯化镉、氢氧化钾和硫脲为反应物采用化学水浴法制备了硫化镉薄膜,为了作对比研究,采用射频磁控溅射以硫化镉为靶材,氩气为溅射气体,制备了硫化镉薄膜。采用X射线衍射、扫描电子显微镜和紫外-可见光光谱仪分别表征了硫化镉薄膜的结构、形貌和光学吸收特性。结果表明,采用以上两种方法制备的硫化镉均具有(002)择优取向,溅射法制备的硫化镉薄膜较致密,薄膜表面较光滑,平均晶粒尺寸在20～30nm;水浴法制备的硫化镉薄膜颗粒尺寸较小,缺陷较多。除了在短波段溅射所得硫化镉薄膜的透过率略差于水浴法所得硫化镉薄膜之外,溅射法制备的硫化镉薄膜的性能整体上优于水浴法制备的薄膜。两种方法制备的硫化镉薄膜的能隙在2.3～2.5eV。     

Synthesis and characterization of porous crystalline SiC thin films prepared by radio frequency reactive magnetron sputtering technique

Hexagonal SiC thin films have been deposited using radio frequency reactive magnetron sputtering technique by varying the substrate temperature and other deposition conditions. Prior to deposition surface modification of the substrate Si(1 0 0) played an important role in deposition of the hexagonal SiC structure. The effect of substrate temperature during deposition on structure, composition and surface morphology of the SiC films has been analyzed using atomic force microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry. X-ray diffraction in conventional θ-2θ mode and omega scan mode revealed that the deposited films were crystalline having 8H-SiC structure and crystallinity improved with increase of deposition temperature. The bonding order and Si-C composition within the films showed improvement with the increase of deposition temperature. The surface of thin films grew in the shape of globes and columns depending upon deposition temperature. The optical properties also showed improvement with increase of deposition temperature and the results obtained by ellipsometry reinforced the results of other techniques.     

Leakage currents in ferroelectric thin films

The main mechanisms of leakage currents in thin lead zirconate titanate (PZT) ferroelectric films prepared by the sol–gel method are discussed. Four specific regions are determined in I–V dependencies. At very weak fields (10–20 kV/cm), the current falls with the voltage increase as a result of depolarization. In the low fields region (about 70–100 kV/cm), the leakage current decreases with the decrease of voltage ramp speed and its components are the ohmic and displacement currents. In the high fields region (≥130 kV/cm), the leakage current increases with the decrease of step voltage ramp in contrast to the previous case. Possible conductivity mechanisms are the Poole– Frenkel emission and hopping conduction. In the transition region between above-mentioned ones (from 80–90 to ～130 kV/cm), an abrupt unstable increase of current is observed caused by breakdown of reverse bias Schottky barrier. Depolarization currents are studied for sol–gel PZT films prepared at different preparation conditions.     

Influence of the blend compatibility on the morphology of thin polymer blend films

Thin films of incompatible polymer blends can form a variety of structures on preparation. For the polymer blend system consisting of two poly(styrene-co-para-bromo-styrene)s at different degrees of bromination, PBr_xS/PBr_yS, the compatibility can be tuned through a variation of the difference in the degree of bromination. Within this blend system, two series of samples with different compatibilities were investigated at various blend compositions. The surface morphology of the thin films was investigated by atomic force microscopy (AFM) measurements, while diffuse X-ray scattering provided additional depth sensitivity at a comparable lateral resolution. The results are indicative for phase separation lateral, as well as perpendicular, to the sample surface.     

Investigations on the mechanism of carrier transport in plasma polymerized pyrrole thin films

Plasma polymerization is found to be an excellent technique for the preparation of good quality, pinhole-free, polymer thin films from different monomer precursors. The present work describes the preparation and characterization of polypyrrole (PPy) thin films by ac plasma polymerization technique in their pristine and in situ iodine doped forms. The electrical conductivity studies of the aluminium-polymer-aluminium (Al-polymer-Al) structures have been carried out and a space charge limited conduction (SCLC) mechanism is identified as the most probable mechanism of carrier transport in these polymer films. The electrical conductivity shows an enhanced value in the iodine doped sample. The reduction of optical band gap by iodine doping is correlated with the observed conductivity results.     

Effects of temperature-induced stress on the structural,electrical, and optical properties of ZnO:Ga thin films grown on Si substrates

Crystalline ZnO:Ga thin films with highly preferential c-axis oriented crystals were prepared on Si(001) substrates at different temperatures using the reactive magnetron sputtering technique. Effects of temperature-induced stress in ZnO:Ga films were investigated using X-ray diffraction (XRD), atomic force microscopy (AFM), electrical transport, and spectroscopic ellipsometry measurements. XRD results showed that the films were highly c-axis (out-of-plane) oriented and crystallinity improved with growth temperature. The residual compressive stress in films grown at low temperature relaxes with substrate temperature and becomes tensile stress with further increases in growth temperature. Resistivity of the films decreases with increasing stress, while the carrier concentration and mobility increase as the stress increases. The mechanism of the stress-dependent bandgap of ZnO:Ga films grown at different temperatures is suggested in the present work.     

Impact of chloride treatment on the physical properties of polycrystalline thin CdTe films for solar cell applications

This report presents the microstructural, optoelectrical and surface morphological properties of e-beam evaporated thin CdTe films with the activation of post-chloride treatment. The thin films having thickness 800 nm were deposited onto glass and ITO substrates subsequently processed with CdCl₂ treatment at various temperatures and then subjected to different characterization tools to investigate the physical properties. The films were found to be polycrystalline in nature having a cubic phase with preferred orientation (111) up to 320 °C and completely oxidized at 470 °C while the ohmic nature of films is confirmed by I–V characteristics. The absorbance is found to be higher in the visible range and lowest transmittance is observed for film processed at 170 °C. The surface morphology reveals that films have uniform surface with improved grain growth and elemental analysis confirms the deposition and treatment. The optimized results attract attention to use the processed films at 170 °C as an effective absorber-layer in CdTe based solar cells.     

Substrate dependent properties of electrodeposited EuTe thin films

In electrodeposition, substrate besides providing mechanical support to the electrodeposit, affects significantly the structural and morphological properties of a film. Electrodeposition and characterization of EuTe thin films onto different substrates such as stainless steel (SS), titanium (Ti), copper (Cu), fluorine-doped tin oxide (F:SnO₂) covered glasses have been described. The deposition potentials have been estimated from the polarization curves. The reaction mechanism is proposed for the formation of EuTe electrodeposits. Preparative parameters such as deposition potential, current density, and deposition time are studied. The films have been characterized by X-ray diffraction, scanning electron microscopy (SEM), atomic force microscopy (AFM) and energy dispersive analysis by X-rays (EDAX) techniques. The electrodeposited EuTe films are polycrystalline on all the substrates with same cubic crystal structure. The SEM studies reveal that the surface morphology is different for the substrates studied. However, no cracks have been observed in the SEM micrographs. The AFM images show large spherical grains supporting the polycrystalline nature of the samples. The EDAX analysis shows that the EuTe films are nearly stoichiometric, slightly rich in tellurium.     

Effect of excess Pb on crystallinity and ferroelectric properties of PZT(40/60) films on LaNiO3 coated Si substrates by MOD technique

Pb(Zr_0.4Ti_0.6)O₃ [PZT(40/60)] films were deposited onto LaNiO₃ (LNO) coated Si substrates by metal-organic decomposition (MOD) technique. Excess Pb was incorporated in the film by using excess Pb (2%–15%) in the solution. The crystallinity and ferroelectric properties of PZT films were investigated by using X-ray diffraction (XRD), RT66A test system and HP4194 impedance analyzer, respectively. Rayleigh law was employed to analyze the defect concentration in the films. The results show that all the PZT films show the (1 0 0) preferential orientation with complete perovskite structure except for the 2% film displaying some pyrochlore phase. The (1 0 0) preferential orientation is mainly attributed to LNO bottom electrode, which has the highly (1 0 0) preferential orientation. The 10% film shows the best polarization and dielectric properties. The remnant polarization and coercive field are about 10.1 μC/cm² and 73 kV/cm under an electric field around 330 kV/cm, respectively. And the dielectric constant and dissipation factor are about 656 and 0.022 at a frequency of 1 kHz, respectively. The good ferroelectric properties of the 10% film are mainly attributed to the low defect concentration in the film.     

Electrodeposition and growth mechanism of SnSe thin films

Tin selenide (SnSe) thin films were electrochemically deposited onto Au(1 1 1) substrates from an aqueous solution containing SnCl₂, Na₂SeO₃, and EDTA at room temperature (25 °C). The electrochemical behaviors and the codeposition potentials of Sn and Se were explored by cyclic voltammetry. X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and UV-vis absorption spectroscopy were employed to characterize the thin films. When the electrodeposition potential increased, the Se content in the films decreased. It was found that the stoichiometric SnSe thin films could be obtained at −0.50 V. The as-deposited films were crystallized in the preferential orientation along the (1 1 1) plane. The morphologies of SnSe films could be changed from spherical grains to platelet-like particles as the deposition potential increases. The SEM investigations show that the film growth proceeds via nucleation, growth of film layer and formation of needle-like particles on the overlayer of the film. The optical absorption study showed the film has direct transition with band gap energy of 1.3 eV.     

Influence of polyethylene glycol-300 addition on nanostructured lead sulfide thin films properties

The concentration of polyethylene glycol-300 was found to play a crucial role in the formation of nanoparticles in PbS-chemical bath deposition process. We report here an endeavor to set up a relation between the variation of lead sulfide (PbS) nanocrystalline thin film properties, grown by (CBD) process at room temperature on corning glass and Si(100) substrates, with amount fluctuations of polyethylene glycol-300 in the solution. The transmittance of the films, for a fixed reaction time, increased up to ∼ 80% with the increase of % polyethylene glycol-300 in the solution, indicating the formation of very thin films due to the decrease of reaction rate with the increase of the concentration of polyethylene glycol-300. The optical band gaps were found to strongly rely on the composition of the bath deposition and increase with the increase of the polyethylene glycol-300 amount in the solution. Particle sizes between 2.8 and 8.7 nm were obtained by varying the % of polyethylene glycol-300 from 0.2 to 1.5. The concentration of polyethylene glycol-300 not only affects the reaction rate but also the morphology of the obtained films. PbS nanoparticles were found to be oriented preferentially along the < 200> plane. The absorption shifts towards short wavelength indicating a blue-shifting as a consequence of quantum confinement.     

Influence of Fe ions in characteristics and optical properties of mesoporous titanium oxide thin films

Fe-doped mesoporous titanium dioxide (M-TiO₂-Fe) thin films have been prepared on indium tin oxide (ITO) glass substrates by sol–gel and spin coating methods. All films exhibited mesoporous structure with the pore size around 5–9 nm characterized by small angle X-ray diffraction (SAXRD) and further confirmed by high resolution transmission electron microscopy (HRTEM). Raman spectra illustrated that lower Fe-doping contributed to the formation of nanocrystalline of M-TiO₂-Fe thin films. X-ray photoelectron spectroscopy (XPS) data indicated that the doped Fe ions exist in forms of Fe³⁺, which can play a role as e⁻ or h⁺ traps and reduce e⁻/h⁺ pair recombination rate. Optical properties including refractive indices/n, energy gaps/E_g and Urbach energy width/E₀ of the thin films were estimated and investigated by UV/vis transmittance spectra. The presence of Fe content extended the light absorption band and decreased the values of n, implying enhanced light response and performance on dye-sensitized solar cells (DSSC). The optimum Fe content in M-TiO₂-Fe thin films is determined as 10 mol%, for its compatibility of well crystalline and well potential electron transfer performance.