Comparison of O adsorption on Ni3Al (0 0 1), (0 1 1), and (1 1 1) surfaces through first-principles calculations

First-principles calculations were performed to study the properties of O adsorption on Ni₃Al (0 0 1), (0 1 1), and (1 1 1) surfaces using the Cambridge serial total package (CASTEP) code. Stable adsorption sites are identified. The atomic and electronic structures and adsorption energies are predicted. The adsorption sites for O on the Ni₃Al (0 0 1) surface are at the 2Ni–2Al fourfold hollow site, whereas O prefers to adsorb at the Ni–Al bridge site on (0 1 1) surface and 2Ni–Al threefold hollow site on (1 1 1) surface. It is found that O shows the strongest affinity for Al and the state of O is the most stabilized when O adsorbs on (0 0 1) surface, while the affinity of O for Al on (0 1 1) surface is weaker than (0 0 1) surface, and (1 1 1) surface is the weakest. The stronger O and Al affinity indicates more stable Al₂O₃ when oxidized. The experiment has shown that the oxidation resistance of single crystal superalloy in different orientations improves in the order of (1 1 1), (0 1 1), and (0 0 1) surface, suggesting that the oxidation in different crystallographic orientations may be related to the affinity of O for Al in the surface.     

Theoretical study of CO adsorption on the illuminated TiO2 (0 0 1) surface

A quantum modeling of the CO adsorption on illuminated anatase TiO₂ (0 0 1) is presented. The calculated adsorption energy and geometries of illuminated case are compared with the ground state case. The calculations were achieved by using DFT formalism and the BH and HLYP. Upon photoexcitation, an electron-hole pair is generated. Comparing of natural population in the ground state and the exited state, shows that an electron is trapped in a Ti⁴⁺ ion and a hole is localized in an oxygen ion. The photoelectron helps generation of a CO₂ molecule on the TiO₂ surface. As shown by optimization of these systems, the CO molecule adsorbed vertically on the TiO₂ (0 0 1) surface in the ground state case while the CO molecule made an angle of 134.3° to this surface at the excited state case. Based on the here used model the obtained adsorption energy was 0.36 eV which is in excellent agreement with the reported experimental value. In the present work the C-O stretch IR frequencies are calculated which are 1366.53 and 1423.16 cm⁻¹. These results are in good agreement with the earlier reported works for the surface carbonaceous compounds, and oxygenated carbon species.     

CO methanation on Ni(1 1 1) and modified Ni3Al(1 1 1) surfaces: A first-principle study

The adsorption energies of intermediates in CO methanation on the modified Ni₃Al(1 1 1) surface and the Ni(1 1 1) surface are calculated using density functional theory. A microkinetic analysis based on the calculated adsorption energies is performed to explain the different kinetics of CO methanation catalyzed by Ni₃Al and Ni powders. The electronic structures of different atoms on the modified Ni₃Al surface are also presented, and correlate well with the adsorption energies and geometries.     

Adsorption of CO, CO2 and NO molecules on a BaTiO3 (0 0 1) surface

Since the development of Scanning Tunnelling Microscopy (STM) technique, considerable attention has been devoted to various molecules adsorbed on various surfaces. Also, a new concept emerged with molecules on surfaces considered as nano machines by themselves. In this context, a thorough knowledge of surfaces and adsorbed molecules at an atomic scale are thus particularly invaluable. The present work describes the first Density Functional Theory (DFT) study of adsorption of CO, CO₂ and NO molecules on a BaTiO₃ surface following a first preliminary calculation of O and O₂ adsorption on the same surface. In the previously considered work, we found that a (0 0 1) surface with BaO termination is more stable than the one with TiO₂-termination. Consequently, we extended our study to CO, CO₂ and NO molecules adsorbed on a (0 0 1) surface with BaO termination. The present calculation was performed on a (1 × 1) cell with one monolayer of adsorbed molecules. Especially, a series of cases implying CO molecules adsorbed in various geometrical configurations has been examined. The corresponding adsorption energy varies in the range of −0.17 to −0.10 eV. The adsorption energy of a CO₂ molecule directly located above an O surface atom (called O_s) is of the order of −0.18 eV. The O-C distance length is then 1.24 Å and the O-C-O and O-C-O_s angles are 134.0° and 113.0°, respectively. For NO adsorption, the most important induced structural changes are the followings: (i) the N-O bond is broken when a NO molecule is absorbed on a Ba-O_s bridge site. In that case, N and O atoms are located above an O and a Ba surface atom, respectively, whereas the O-Ba-O_s and N-O_s-Ba angles are 106.5° and 63.0°, respectively. The N-O distance is as large as 2.58 Å and the adsorption energy is as much as −2.28 eV. (ii) In the second stable position, the NO molecule has its N atom adsorbed above an O_s atom, the N-O axis being tilted toward the Ba atom. The N-O_s-Ba angle is then 41.1° while the adsorption energy is only −0.10 eV. At last, the local densities of states around C, O as well as N atoms of the considered adsorbed molecules have also been discussed.     

CO2 dissociation on Ni(2 1 1)

The direct and H-mediated dissociation of CO₂ on Ni(2 1 1) were investigated at the level of density functional theory. Although formate (HCOO) formation via CO₂ hydrogenation was widely reported for CO₂ adsorption on metal surfaces, it is found that on Ni(2 1 1) HCOO dissociation into CHO and O is much difficult, while direct dissociation of adsorbed CO₂ into CO and O is more favorable. It is also found that the degree of electron transfer from surface to adsorbed CO₂ correlates with the elongation of C-O bond lengths and the reduction of the CO₂ dissociation barrier.     

Density functional study of oxygen adsorption on the Mg3Nd (0 0 1) surface

The adsorption of oxygen atoms on Mg₃Nd (0 0 1) surface was studied based on density function theory (DFT), in which the exchange-correlation potential was chosen as the generalized gradient approximation (GGA) in the Perdew and Wang (PW91). The most preferred adsorption position was at the top-hollow site. Upon the optimization on top-hollow site with different coverage, it was found that the adsorption energy decreased with oxygen coverage. The density of states analysis showed that obvious charge transfer took place between O atom and the nearest Nd atom and chemical bond formed between O atom and the nearest Nd atom after O adsorption. The result of surface energy as a function of chemical potential change of oxygen indicated the clean Mg₃Nd (0 0 1) surface was easy to adsorb oxygen and form 1.00 ML surface.     

A theoretical investigation on Pt3Sn(1 0 2) surface alloy and CO-Pt3Sn(1 0 2) system

The adsorption properties of CO on experimentally verified stepped Pt₃Sn(1 0 2) surface were investigated using quantum mechanical calculations. The two possible terminations of Pt₃Sn(1 0 2) were generated and on these terminations all types of possible adsorption sites were determined. The adsorption energies and geometries of the CO molecule for all those sites were calculated. The most favorable sites for adsorption were determined as the short bridge site on the terrace of pure-Pt row of the mixed-atom-ending termination, atop site at the step-edge of the pure row of pure-Pt-ending termination and atop site at the step-edge of the pure-Pt row of the mixed-atom-ending termination. The results were compared with those for similar sites on the flat Pt₃Sn(1 1 0) surface considering the fact that Pt₃Sn(1 0 2) has terraces with (1 1 0) orientation. The LDOS analysis of bare sites clearly shows that there are significant differences between the electronic properties of Pt atoms at stepped Pt₃Sn(1 0 2) surface and the electronic properties of Pt atoms at flat (1 1 0) surface, which leads to changes in the CO bonding energies of these Pt atoms. Adsorption on Pt₃Sn(1 0 2) surface is in general stronger compared to that on Pt₃Sn(1 1 0) surface. The difference in adsorption strength of similar sites on these two surface terminations is a result of stepped structure of Pt₃Sn(1 0 2). The local density of states (LDOS) of the adsorbent Pt and C of adsorbed CO was utilized. The LDOS of the surface metal atoms with CO-adsorbed atop and of their bare state were compared to see the effect of CO chemisorption on the electron density distribution of the corresponding Pt atom. The downward shift in energy peak in the LDOS curves as well as changes in the electron densities of the corresponding energy levels indicate the orbital mixing between CO molecular orbitals and metal d-states. The present study showed that the adsorption strength of the sites has a direct relation with their LDOS profiles.     

First-principles calculations for the elastic properties of Ni-base model superalloys: Ni/Ni3Al multilayers

A model system consisting of Ni[001](100)/Ni3Al[001](100) multi-layers are studied using the density functional theory in order to explore the elastic properties of single crystal Ni-based superalloys. Simulation results are consistent with the experimental observation that rafted Ni-base superalloys virtually possess a cubic symmetry. The convergence of the elastic properties with respect to the thickness of the multilayers are tested by a series of multilayers from 2γ′+2γ to 10γ′+10γ atomic layers. The elastic properties are found to vary little with the increase of the multilayer’s thickness. A Ni/Ni3Al multilayer with 10γ′+10γ atomic layers (3.54 nm) can be used to simulate the mechanical properties of Ni-base model superalloys. Our calculated elastic constants, bulk modulus, orientation-dependent shear modulus and Young’s modulus, as well as the Zener anisotropy factor are all compatible with the measured results of Ni-base model superalloys R1 and the advanced commercial superalloys TMS-26, CMSX-4 at a low temperature. The mechanical properties as a function of the γ′ phase volume fraction are calculated by varying the proportion of the γ and γ′ phase in the multilayers. Besides, the mechanical properties of two-phase Ni/Ni3Al multilayer can be well predicted by the Voigt-Reuss-Hill rule of mixtures.     

Solvent effects for CO and H2 adsorption on Cu2O (1 1 1) surface: A density functional theory study

To investigate solvent effects, CO and H₂ adsorption on Cu₂O (1 1 1) surface in vacuum, liquid paraffin, methanol and water are studied by using density functional theory (DFT) combined with the conductor-like solvent model (COSMO). When H₂ and CO adsorb on Cu_cus of Cu₂O (1 1 1) surface, solvent effects can improve CO and H₂ activation. The H-H bond increases with dielectric constant increasing as H₂ adsorption on O_suf of Cu₂O (1 1 1) surface, and the H-H bond breaks in methanol and water. It is also found that both the structural parameters and Mulliken charges are very sensitive to the COSMO solvent model. In summary, the solvent effects have obvious influence on the clean surface of Cu₂O (1 1 1) and the adsorptive behavior.     

Theoretical study of Ni adsorption on the GaN(0 0 0 1) surface

First-principles pseudo-potential calculations within density-functional theory framework are performed in order to study the structural and electronic properties of nickel adsorption and diffusion on a GaN(0 0 0 1)-2×2 surface. The adsorption energies and potential energy surfaces are investigated for a Ni adatom on the Ga-terminated (0 0 0 1) surface of GaN. This surface is also used to study the effect of the nickel surface coverage. The results show that the most stable positions of a Ni adatom on GaN(0 0 0 1) are at the H₃ sites and T₄ sites, for low and high Ni coverage respectively. In addition, confirming previous experimental results, we have found that the growth of Ni monolayers on the GaN(0 0 0 1) surface is possible.     

Order–disorder transition in nanocrystalline Ni3Al prepared by a chemical route

Ni₃Al alloys of nanometer dimensions in the range 10–38 nm could be synthesized by reaction sintering of sol–gel-derived Ni/SiO₂ nanocomposite and commercially available micrometer-sized aluminum powder. The sintering was carried out at a temperature of 923 K and a pressure of 2.4 MPa. By a suitable choice of sintering conditions a disordered phase of Ni₃Al was stabilized. The disordered phase could be converted to an ordered one by an increase of heat treatment temperature.     

Density functional study of hypophosphite adsorption on Ni (1 1 1) and Cu (1 1 1) surfaces

Surface structures and electronic properties of hypophosphite, H₂PO₂⁻, molecularly adsorbed on Ni(1 1 1) and Cu(1 1 1) surfaces are investigated in this work by density functional theory at B3LYP/6-31++g(d, p) level. We employ a four-metal-atom cluster as the simplified model for the surface and have fully optimized the geometry and orientation of H₂PO₂⁻ on the metal cluster. Six stable orientations have been discovered on both Ni (1 1 1) and Cu (1 1 1) surfaces. The most stable orientation of H₂PO₂⁻ was found to have its two oxygen atoms interact the surface with two PO bonds pointing downward. Results of the Mulliken population analysis showed that the back donation from 3d orbitals of the transition metal substrate to the unfilled 3d orbital of the phosphorus atom in H₂PO₂⁻ and 4s orbital's acceptance of electron donation from one lone pair of the oxygen atom in H₂PO₂⁻ play very important roles in the H₂PO₂⁻ adsorption on the transition metals. The averaged electron configuration of Ni in Ni₄ cluster is 4s^0.634p^0.023d^9.35 and that of Cu in Cu₄ cluster is 4s^1.004p^0.033d^9.97. Because of this subtle difference of electron configuration, the adsorption energy is larger on the Ni surface than on the Cu surface. The amount of charge transfers due to above two donations is larger from H₂PO₂⁻ to the Ni surface than to the Cu surface, leading to a more positively charged P atom in Ni_nH₂PO₂⁻ than in Cu_nH₂PO₂⁻. These results indicate that the phosphorus atom in Ni_nH₂PO₂⁻ complex is easier to be attacked by a nucleophile such as OH⁻ and subsequent oxidation of H₂PO₂⁻ can take place more favorably on Ni substrate than on Cu substrate.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Ab initio simulation of the BaZrO3 (0 0 1) surface structure

Electronic and atomic structures of different terminations of the (0 0 1) non-polar orientation of BaZrO₃ surfaces have been studied using first-principles calculations. We found that surface energies at both possible surface terminations, BaO and ZrO₂, were very close. The (0 0 1)-BaO and (0 0 1)-ZrO₂ terminated surfaces have bandgap values smaller than that of a bulk BaZrO₃ crystal. In addition, the relative surface stability has been analyzed as a function of chemical environment.     

Theoretical study of oxygen adsorption at the Fe(1 1 0) and (1 0 0) surfaces

Electronic, magnetic and structural properties of atomic oxygen adsorbed in on-surface and subsurface sites at the two most densely packed iron surfaces are investigated using density functional theory combined with a thermodynamics formalism. Oxygen coverages varying from a quarter to two monolayers (MLs) are considered. At a 1/4 ML coverage, the most stable on-surface adsorption sites are the twofold long bridge sites on the (1 1 0), and the fourfold-hollow sites on the (1 0 0) surface. The presence of on-surface oxygen atoms enhances the magnetic moments of the atoms of the two topmost Fe layers. Detailed results on the surface magnetic properties, due to O incorporation, are presented as well. Subsurface adsorption is found unfavored. The most stable subsurface O, in tetrahedral positions at the (1 0 0) and octahedral ones at the (1 1 0) surface, are characterized by substantially lower binding than that in the on-surface sites. Subsurface oxygen increases the interplanar distance between the uppermost Fe layers. The preadsorbed oxygen overlayer enhances binding of subsurface O atoms, particularly for tetrahedral sites beneath the (1 1 0) surface.     

The corrosion behavior of intermetallic compounds Ni3(Si,Ti) and Ni3(Si,Ti) + 2Mo in acidic solutions

The corrosion behavior of the intermetallic compounds homogenized, Ni₃(Si,Ti) (L1₂: single phase) and Ni₃(Si,Ti) + 2Mo (L1₂ and (L1₂ + Ni_ss) mixture region), has been investigated using an immersion test, electrochemical method and surface analytical method (SEM; scanning electron microscope and EPMA: electron probe microanalysis) in 0.5 kmol/m³ H₂SO₄ and 0.5 kmol/m³ HCl solutions at 303 K. In addition, the corrosion behavior of a solution annealed austenitic stainless steel type 304 was studied under the same experimental conditions as a reference. It was found that the intergranular attack was observed for Ni₃(Si,Ti) at an initial stage of the immersion test, but not Ni₃(Si,Ti) + 2Mo, while Ni₃(Si,Ti) + 2Mo had the preferential dissolution of L1₂ with a lower Mo concentration compared to (L1₂ + Ni_ss) mixture region. From the immersion test and polarization curves, Ni₃(Si,Ti) + 2Mo showed the lowest corrosion resistance in both solutions and Ni₃(Si,Ti) had the highest corrosion resistance in the HCl solution, but not in the H₂SO₄ solution. For instance, it was found that unlike type 304 stainless steel, these intermetallic compounds were difficult to form a stable passive film in the H₂SO₄ solution. The results obtained were explained in terms of boron segregation at grain boundaries, Mo enrichment and film stability (or strength).     

First-principle study of NO adsorption on the LaFeO3 (0 1 0) surface

The adsorption of NO molecule on the LaFeO₃ (0 1 0) surface was studied using first-principle calculations based on density functional theory. The calculated results indicate that the Fe-top site is the most favorable for NO adsorption. The N-O bond length, Mulliken charge, and the N-O vibration frequency of the NO molecule are discussed after adsorption. The analysis results of the density of the states show that when NO is adsorbed with the Fe-NO configuration, the bonding mechanism is mainly from the interaction between the NO and the Fe d orbit.     

Diffusion research between Ni3Al coating and titanium alloy produced by plasma spraying process

A Ni₃Al coating was prepared by plasma spraying technique on the surface of titanium alloy. Ni-Al mixed powders, coatings and reaction products were investigated by scanning electron microscope, EDS, DSC and XRD. A tight bonding between the coating and the substrate was formed. The X-ray diffraction analysis of the patterns showed that the coating not only had Ni₃Al phase, but also had NiO and Al₂O₃ phase microcontent. Comparing Ni coated Al to Ni₃Al at 900 °C, the diffusion was stronger and the diffusion layer was thicker. A minute pore structure was formed at 1200 °C in the front edge of solid-state reaction layer. So Ni₃Al restrained the solid-state reaction of the coating with the substrate, and as a whole weakened the entry of oxygen atoms into the substrate and quenched the out-diffusion of titanium.     

Structural properties and diffusion processes of the Cu3Au (0 0 1) surface

The surface relaxation and surface energy of both the mixed AuCu and pure Cu terminated Cu₃Au (0 0 1) surfaces are simulated and calculated by using the modified analytical embedded-atom method. We find that the mixed AuCu termination is energetically preferred over the pure Cu termination thereby the mono-vacancy diffusion is also investigated in the topmost few layers of the mixed AuCu terminated Cu₃Au (0 0 1) surface. In the mixed AuCu terminated surface the relaxed Au atoms are raised above Cu atoms for 0.13 Å in the topmost layer. All the surface atoms displace outwards, this effect occurs in the first three layers and changes the first two inter-layer spacing. For mono-vacancy migration in the first layer, the migration energies of Au and Cu mono-vacancy via two-type in-plane displace: the nearest neighbor jump (NNJ) and the second nearest neighbor jump (2NNJ), are calculated and the results show that the NNJ requires a much lower energy than 2NNJ. For the evolution of the energy requirements for successive nearest neighbor jumps (SNNJ) along three different paths: circularity, zigzag and beeline, we find that the circularity path is preferred over the other two paths due to its minimum energy barriers and final energies. In the second layer, the NN jumps in intra- and inter-layer of the Cu mono-vacancy are investigated. The calculated energy barriers and final energies show that the vacancy prefer jump up to a proximate Cu site. This replacement between the Cu vacancy in the second layer and Cu atom in the first layer is remunerative for the Au atoms enrichment in the topmost layer.     

DFT study on dissociative adsorption of SiH4 and GeH4 on SiGe(1 0 0)-2 × 1 surface

SiH₄ and GeH₄ dissociative adsorptions on a buckled SiGe(1 0 0)-2 × 1 surface have been analyzed using density functional theory (DFT) at the B3LYP level. The Ge alloying in the Si(1 0 0)-2 × 1 surface affects the dimer buckling and its surface reactivity. Systematic Ge influences on the reaction energetics are found in SiH₄ and GeH₄ reactions with four dimers of Si^∗-Si, Ge^∗-Si, Ge^∗-Ge, and Si^∗-Ge (∗ denotes the protruded atom). On a half H-covered surface, the energy barriers for silane and germane adsorption are higher than those on the pristine surface. The energy barrier for silane adsorption is higher than the corresponding barrier for germane adsorption. Rate constants are also calculated using the transition-state theory. We conclude that the SiGe surface reactivity in adsorption reaction depends on the Ge presence in dimer form. If the surface Ge is present in form of Ge^∗-Ge, the surface reactivity decreases as the Ge^∗-Ge content increases. If the surface Ge prefers to be in form of Ge^∗-Si at low Ge contents, the surface reactivity increases first, then decreases at high Ge surface contents when Ge^∗-Ge prevails. The calculated rate constant ratio of GeH₄ adsorption on Si^∗-Si over Ge^∗-Ge at 650 °C is 2.1, which agrees with the experimental ratio of GeH₄ adsorption probability on Si(1 0 0) over Si(1 0 0) covered by one monolayer Ge. The experimental ratio is 1.7 measured through supersonic molecular beam techniques. This consistency between calculation and experimental results supports that one monolayer of Ge on Si(1 0 0) exists in form of Ge^∗-Ge dimer.