Nanosilver surface plasmon response enhanced the photovoltaic performance of organic solar cells

Nanosilver island thin films with different thickness were synthesized by vacuum vapor deposition between ITO and PEDOT:PSS for organic solar cells, forming the structure of ITO/AgNPs layer/PEDOT:PSS/P3HT:PCBM/LiF/Al. Surface morphology and UV–vis absorption spectrum were investigated by AFM and UV–vis scanning spectrophotometer. It was found that after adding the nanosilver film, the optical properties of the device were enhanced with increasing the thickness of nanosilver island films. When the thickness of nanosilver thin films is 3.0 nm, the most significant surface plasmon response and red-shift of the resonance absorption peak appeared. Meanwhile, short circuit current density of the device increased from 9.93 mA/cm² to 12.98 mA/cm², the fill factor increased from 49.35% to 52.79% and the power conversion efficiency increased from 3.05% to 4.01%. These results provided a theoretical guidance to optimize the design and increase the performance of solar cells.     

Thickness study of Al:ZnO film for application as a window layer in Cu(In1−xGax)Se2 thin film solar cell

Structural, electrical and optical properties of Al doped ZnO (Al:ZnO) thin film of various thicknesses, grown by radio-frequency magnetron sputtering system were studied in relation to the application as a window layer in Cu(In_1−xGa_x)Se₂ (CIGS) thin film solar cell. It was found that the electrical and structural properties of Al:ZnO film improved with increasing its thickness, however, the optical properties degraded. The short circuit current density, J_sc of the fabricated CIGS based solar cells was significantly influenced by the variation of the Al:ZnO window layer thickness. Best efficiency was obtained when CIGS solar cell was fabricated with electrically and optically optimized Al:ZnO window layer.     

In_2O_3:Sn中间层改善B掺杂ZnO薄膜的性能及其应用研究

金属有机化学气相沉积(MOCVD)法生长的掺硼氧化锌(BZO)薄膜,具有天然的"类金字塔"绒面结构,作为硅基薄膜太阳电池的前电极具有良好的陷光效果.但直接获得的BZO薄膜表面形貌过于尖锐,影响后续硅基薄膜材料生长质量及太阳电池的光电转换效率.本文设计了以一层超薄In2O3:Sn(ITO)薄膜(～4 nm厚度)作为中间层的多层膜,并通过对顶层BZO薄膜的厚度调制,改善BZO薄膜的表面特性,薄膜结构为:glass/底层BZO/ITO/顶层BZO.合适厚度的顶层BZO薄膜有助于获得类似"菜花状"形貌特征,尖锐的表面趋于"柔和",而较厚的顶层BZO薄膜仍然保持"类金字塔状"结构."柔和"的BZO薄膜表面结构有助于提高后续生长薄膜电池的结晶质量.将获得的新型"三明治"结构多层膜应用于p-i-n型氢化微晶硅(μc-Si:H)薄膜太阳电池,相比传统的BZO薄膜,电池的量子效率QE在500—800 nm波长范围提高了～10%,并且电池的Jsc和Voc均有所提高.     

Low temperature deposition of transparent conducting ITO/Au/ITO films by reactive magnetron sputtering

Transparent conducting indium tin oxide/Au/indium tin oxide (ITO) multilayered films were deposited on unheated polycarbonate substrates by magnetron sputtering. The thickness of the Au intermediated film varied from 5 to 20 nm. Changes in the microstructure, surface roughness and optoelectrical properties of the ITO/Au/ITO films were investigated with respect to the thickness of the Au intermediated layer. X-ray diffraction measurements of ITO single layer films did not show characteristic diffraction peaks, while ITO/Au/ITO films showed an In₂O₃ (2 2 2) characteristic diffraction peak. The optoelectrical properties of the films were also dependent on the presence and thickness of the Au thin film. The ITO 50 nm/Au 10 nm/ITO 40 nm films had a sheet resistance of 5.6 Ω/□ and an average optical transmittance of 72% in the visible wavelength range of 400-700 nm. Consequently, the crystallinity, which affects the optoelectrical properties of ITO films, can be enhanced with Au intermediated films.     

ZnO nanorods/plates on Si substrate grown by low-temperature hydrothermal reaction

The zinc oxide (ZnO) nanorods/plates are obtained via hydrothermal method assisted by etched porous Al film on Si substrate. The products consist of nanorods with average diameter of 100 nm and nanoplates with thickness of 200-300 nm, which are uniformly distributed widely and grown perpendicularly to the substrate. The ZnO nanoplates with thickness of 150-300 nm were grown on Si substrate coated with a thin continuous Al film (without etching) in the same aqueous solution. The growth mechanism and room temperature photoluminescence (PL) properties of ZnO nanorods/plates and nanoplates were investigated. It is found that the introduction of the etched Al film plays a key role in the formation of ZnO nanorods/plates. The annealing process is favorable to enhance the UV PL emissions of the ZnO nanorods/plates.     

Characteristic difference between ITO/ZrCu and ITO/Ag bi-layer films as transparent electrodes deposited on PET substrate

The metallic-glass film of ZrCu layer deposited by co-sputtering was utilized as the metallic layer in the bi-layer structure transparent conductive electrode of ITO/ZrCu (IZC) deposited on the PET substrate using magnetron sputtering at room temperature. In addition, the pure Ag metal layer was applied in the same structure of transparent conductive film, ITO/Ag, in comparison with the IZC film. The ZrCu layer could form a continuous and smooth film in thickness lower than 6 nm, compared with the island structure of pure Ag layer of the same thickness. The 30 nm ITO/3 nm ZrCu films could show the optical transmittance of 73% at 550 nm wavelength. The 30 nm ITO/12 nm ZrCu films could show the better sheet resistance of 20 Ω/sq, but it was still worse than that of the ITO/Ag films. It was suggested that an alloy system with lower resistivity and negative mixing heat between atoms might be another way to form a continuous layer in thickness lower than 6 nm for metal film.     

Electro-optical characterization and analysis of CuPc-based solar cells with high photovoltage

Organic solar cells using the CuPc and PTCBI semiconductor layers were studied. A high open circuit voltage of 1.15 V was obtained in a device with ITO/PEDOT:PSS/CuPc (15 nm)/PTCBI (7 nm)/Al structure. Results were interpreted in terms of a modified CuPc-Al Schottky diode for the thin PTCBI case and a CuPc-PTCBI heterojunction for the thick PTCBI case. Also, the formation of a thin aluminum oxide layer under the aluminum electrode was postulated. This layer has a beneficial aspect wherein shunting losses are reduced and a high photovoltage is enabled. However, it adds greatly to the series resistance to a point where the short circuit current density is reduced. CuPc Schottky diodes with an ITO/PEDOT:PSS/CuPc/Al structure yielded a high V _oc of 900 mV for a CuPc layer of thickness 140 nm. The V _oc increased with increase in CuPc layer thickness.     

Direct current magnetron sputter-deposited ZnO thin films

Zinc oxide (ZnO) is a very promising electronic material for emerging transparent large-area electronic applications including thin-film sensors, transistors and solar cells. We fabricated ZnO thin films by employing direct current (DC) magnetron sputtering deposition technique. ZnO films with different thicknesses ranging from 150 nm to 750 nm were deposited on glass substrates. The deposition pressure and the substrate temperature were varied from 12 mTorr to 25 mTorr, and from room temperature to 450 °C, respectively. The influence of the film thickness, deposition pressure and the substrate temperature on structural and optical properties of the ZnO films was investigated using atomic force microscopy (AFM) and ultraviolet-visible (UV-Vis) spectrometer. The experimental results reveal that the film thickness, deposition pressure and the substrate temperature play significant role in the structural formation and the optical properties of the deposited ZnO thin films.     

Improvement of organic solar cells by flexible substrate and ITO surface treatments

In this paper, surface treatments on polyethylene terephthalate with polymeric hard coating (PET-HC) substrates are described. The effect of the contact angle on the treatment is first investigated. It has been observed that detergent is quite effective in removing organic contamination on the flexible PET-HC substrates. Next, using a DC-reactive magnetron sputter, indium tin oxide (ITO) thin films of 90 nm are grown on a substrate treated by detergent. Then, various ITO surface treatments are made for improving the performance of the finally developed organic solar cells with structure Al/P3HT:PCBM/PEDOT:PSS/ITO/PET. It is found that the parameters of the ITO including resistivity, carrier concentration, transmittance, surface morphology, and work function depended on the surface treatments and significantly influence the solar cell performance. With the optimal conditions for detergent treatment on flexible PET substrates, the ITO film with a resistivity of 5.6 × 10⁻⁴ Ω cm and average optical transmittance of 84.1% in the visible region are obtained. The optimal ITO surface treated by detergent for 5 min and then by UV ozone for 20 min exhibits the best WF value of 5.22 eV. This improves about 8.30% in the WF compared with that of the untreated ITO film. In the case of optimal treatment with the organic photovoltaic device, meanwhile, 36.6% enhancement in short circuit current density (J_sc) and 92.7% enhancement in conversion efficiency (η) over the untreated solar cell are obtained.     

The influence of using different substrates on the structural and optical characteristics of ZnO thin films

ZnO thin films with thikness d = 100 nm were deposited onto different substrates such as glass, kapton, and silicon by radio frequency magnetron sputtering. The structural analyses of the films indicate they are polycrystalline and have a wurtzite (hexagonal) structure.The ZnO layer deposited on kapton substrate shows a stronger orientation of the crystallites with (0 0 2) plane parallel to the substrate surface, as compared with the other two samples of ZnO deposited on glass and silicon, respectively.All three layers have nanometer-scale values for roughness, namely 1.7 nm for ZnO/glass, 2.4 nm for ZnO/silicon, and 6.8 nm for ZnO/kapton. The higher value for the ZnO layer deposited on kapton substrate makes this sample suitable for solar cells applications. Transmission spectra of these thin films are strongly influenced by deposition conditions. With our deposition conditions the transparent conducting ZnO layer has a good transmission (78-88%) in VIS and NIR domains. The values of the energy gap calculated from the absorption spectra are 3.23 eV for ZnO sample deposited onto glass substrate and 3.30 eV for the ZnO sample deposited onto kapton polymer foil substrate. The influence of deposition arrangement and oxidation conditions on the structural, morphological, and optical properties of the ZnO films is discussed in the present paper.     

Preparation of chemically deposited thin films of CdS/PbS solar cell

The present paper reports the preparation of a solar cell which has a cross-sectional scheme: ITO/CdS/PbS, containing a commercially transparent conductive ITO; chemically deposited n-type CdS (340 nm) and absorbed layer of p-type PbS (1400 nm). The structural and optical properties of the constituent films are presented. X-ray diffraction showed that all of the thin films are polycrystalline. Using scanning electron microscopy, the present study revealed that the films have uniform surface morphology over the substrate. The solar cell was characterized by determining the open circuit voltage, short-circuit current density, and J–V under 40 mW/cm² solar radiation. The efficiency of the solar cells was 1.35%, which is much higher (0.041, 0.5 and 0.1–0.4%) and slightly smaller (1.65%) than some solar cells reported in the literature.     

ZnO/Ag/ZnO multilayer films for the application of a very low resistance transparent electrode

Transparent conductive ZnO/Ag/ZnO multilayer electrodes having much lower electrical resistance than the widely used transparent electrodes were prepared by simultaneous RF magnetron sputtering of ZnO and DC magnetron sputtering of Ag. An Ag film with different thickness was used as intermediate metallic layers. The optimum thickness of Ag thin films was determined to be 6 nm for high optical transmittance and good electrical conductivity. With about 20-25 nm thick ZnO films, the multilayer showed high optical transmittance in the visible range of the spectrum and had color neutrality. The electrical and optical properties of the multilayers were changed mainly by Ag film properties. A high quality transparent electrode, having sheet resistance as low as 3 ohm/sq and high transmittance of 90% at 580 nm, was obtained and could be reproduced by controlling the preparation parameter properly. The above property is suitable as transparent electrode for dye sensitized solar cells (DSSC).     

Study on the electrical and optical properties of Ag/Al-doped ZnO coatings deposited by electron beam evaporation

A layer of silver was deposited onto the surface of glass substrates, coated with AZO (Al-doped ZnO), to form Ag/AZO film structures, using e-beam evaporation techniques. The electrical and optical properties of AZO, Ag and Ag/AZO film structures were studied. The deposition of Ag layer on the surface of AZO films resulted in lowering the effective electrical resistivity with a slight reduction of their optical transmittance. Ag (11 nm)/AZO (25 nm) film structure, with an accuracy of ±0.5 nm for the thickness shows a sheet resistance as low as 5.6 ± 0.5 Ω/sq and a transmittance of about 66 ± 2%. A coating consisting of AZO (25 nm)/Ag (11 nm)/AZO (25 nm) trilayer structure, exhibits a resistance of 7.7 ± 0.5 Ω/sq and a high transmittance of 85 ± 2%. The coatings have satisfactory properties of low resistance, high transmittance and highest figure of merit for application in optoelectronics devices including flat displays, thin films transistors and solar cells as transparent conductive electrodes.     

Effect of mesh patterning with UV pulsed-laser on optical and electrical properties of ZnO/Ag-Ti thin films

In this study, the ZnO/Ag-Ti structure for transparence conducting oxide (TCO) is investigated by optimizing the thickness of the Ag-Ti alloy and ZnO layers. The Ag-Ti thin film is deposited by DC magnetron sputtering and its thicknesses is well controlled. The ZnO thin film is prepared by sol-gel method using zinc acetate as cation source, 2-methoxiethanol as solvent and monoethanolamine as solution stabilizer. The ZnO film deposition is performed by spin-coating technique and dried at 150 °C on Corning 1737 glass. Due to the conductivity of ZnO/Ag-Ti is dominated by Ag-Ti, the sheet resistance of ZnO/Ag-Ti decrease dramatically as the thickness of Ag-Ti layer increases. However, the transmittances of ZnO/Ag-Ti become unacceptable for TCO application after the thickness of Ag-Ti layer beyond 6 nm. The as-deposited ZnO/Ag-Ti structure has the optical transmittance of 83% @ 500 nm and the low resistivity of 1.2 × 10⁻⁵ Ω-cm. Furthermore, for improving the optical and electrical properties of ZnO/Ag-Ti, the thermal treatment using laser is adopted. Experimental results indicate that the transmittance of ZnO/Ag-Ti is improved from 83% to 89% @ 500 nm with resistivity of 1.02 × 10⁻⁵ Ω-cm after laser drilling. The optical spectrum, the resistance, and the morphology of the ZnO/Ag-Ti will be reported in the study.     

Effect of electrically degenerated layer on the carrier transport property of ZnO epitaxial thin films

ZnO films were prepared on (1 1 1) YSZ and (0 0 0 1) sapphire by pulsed laser deposition method. Effect of lattice mismatch on the carrier transport properties of ZnO epitaxial thin films was investigated. The carrier mobility of the ZnO films on YSZ was larger than that of ZnO/sapphire due to smaller lattice mismatch when the thickness was below 150 nm. The effect of electrically degenerated layer on the carrier transport property increased with decreasing the film thickness of ZnO film. The carrier density and electron mobility of 20 nm-thick-ZnO film on either substrate were regardless of the temperature. We concluded that the dominant carrier scattering mechanism in ZnO ultra thin films is double Schottky barriers at the grain boundary and that their height depends on the carrier concentration.     

Effect of doping on structural,optical and electrical properties of nanostructure ZnO films deposited onto a-Si:H/Si heterojunction

We investigated the structural; optical and electrical properties of ZnO thin films as the n-type semiconductor for silicon a-Si:H/Si heterojunction photodiodes. The ZnO film forms the front contact of the super-strata solar cell and has to exhibit good electrical (high conductivity) and optical (high transmittance) properties. In this paper we focused our attention on the influence of doping on device performance. The results show that the X-ray diffraction (XRD) spectra revealed a preferred orientation of the crystallites along c-axis. SEM images show that all films display a granular, polycrystalline morphology and the ZnO:Al exhibits a better grain uniformity. The transmittance of the doped films was found to be higher when compared to undoped ZnO. A low resistivity of the order of 2.8 × 10⁻⁴ Ω cm is obtained for ZnO:Al using 0.4 M concentration of zinc acetate. The photoluminescence (PL) spectra exhibit a blue band with two peaks centered at 442 nm (2.80 eV) and 490 nm (2.53 eV). It is noted that after doping the ZnO films a shift of the band by 22 nm (0.15 eV) is recorded and a high luminescence occurs when using Al as a dopant. Dark I–V curves of ZnO/a-Si:H/Si structure showed large difference, which means there is a kind of barrier to current flow between ZnO and a-Si:H layer. Doping films was applied and the turn-on voltages are around 0.6 V. Under reverse bias, the current of the ZnO/a-Si:H/Si heterojunction is larger than that of ZnO:Al/a-Si:H/Si. The improvement with ZnO:Al is attributed to a higher number of generated carriers in the nanostructure (due to the higher transmittance and a higher luminescence) that increases the probability of collisions.     

Thickness dependence of electrical properties of ITO film deposited on a plastic substrate by RF magnetron sputtering

Indium tin oxide (ITO) films with various thicknesses in range of 40-280 nm were prepared onto a plastic substrate (PMMA). Deposition was carried out with RF magnetron sputtering method and the substrate temperature was held at ∼70 °C, in lack of the thermal damage to the polymer substrate. Changes in microstructure and electrical properties of ITO films according to their thicknesses were investigated. It was found that amorphous layer with thickness of 80 nm was formed at the interface on the polymer substrate and polycrystalline ITO could be obtained above the thickness. Conductivity of ITO films was found to be strongly dependent on the crystallinity. Consequently, it is suggested that crystallinity of the deposited films should be enhanced at the initial stage of deposition and the thickness of amorphous region be reduced in order to prepare high quality ITO thin films on polymer substrates.     

Growth and characterization of ZnO-SDS hybrid thin films prepared by electrochemical self-assembly method

ZnO-SDS hybrid thin films were grown on ITO glass using the potentiostatic electrodeposition route from aqueous zinc nitrate solution containing surfactant sodium dodecyle sulfanate (SDS). The electrochemical process of the hybrid films was analyzed by comparing the cyclic voltammetric curve and current-time curve with those of pure ZnO film. Results showed that the addition of a small amount of SDS could decrease the deposition current density, and inhibit the growth of ZnO crystals significantly. The hybrid films electrodeposited at −0.9 V for 30 min exhibited smooth and platelet-like morphology, with the film thickness of about 110 nm. The well-defined ZnO-SDS lamellar structures could be clearly observed, with two interlayer spaces of 35.1 and 30.9 Å, respectively. Optical analysis showed that the hybrid films had good optical quality, and exhibited the fundamental absorption edge of ZnO at 380 nm.     

Highly crystallized sputtered silicon with textured morphology for thin-film solar cells

A light-trapping structure with textured morphology for thin-film solar cell is demonstrated in this paper. It is fabricated through Al evaporation, and has a root-mean-roughness (Rms) of about 120 nm and lateral width of about 1 μm for single bulge. A Mo layer is introduced to be a barrier layer. Subsequently sputtered amorphous silicon film is 100% crystallized by Cu induced crystallization. Reflectivity of samples with different silicon thickness is studied to reveal the light-trapping efficiency and the reflectivity as low as 10% is obtained with only 840 nm thick silicon film. This is a low-cost structure promising for future thin-film solar cells with high efficiency.     

倒置异质结有机太阳能电池的电子传输层

制备了结构为ITO/BCP或Alq3(x=0,2,6,10,20,40 nm)/C60(50 nm)/Rubrene(50 nm)/MoO3(5nm)/Al(130 nm)的倒置异质结有机太阳能电池,其中BCP或Alq3作电子传输层。实验结果表明:当BCP或Alq3≤6 nm时,器件性能随电子传输层厚度的变化不大;当BCP或Alq3≥10 nm时,随电子传输层厚度的增加,含Alq3器件的性能衰减很快,含BCP器件的性能衰减相对较慢,且其开路电压保持不变。分析表明:当电子传输层较薄时,粗糙的ITO使电子较容易从C60注入到ITO;当电子传输层较厚时,BCP/C60之间的能带弯曲使二者之间几乎不存在势垒,含BCP器件性能较差主要源于BCP较差的电子迁移率,而含Alq3器件性能较差主要源于Alq3/C60之间的势垒。