利用脉冲激光沉积技术在双轴织构的Ni基带上外延CeO2薄膜

利用脉冲激光沉积技术在氢还原气氛下成功地在双轴织构的Ni基带上外延了高质量的CeO₂薄膜. x射线衍射θ—２θ扫描和ω扫描结果表明，CeO₂薄膜在Ni基带上呈c轴方向生长，存在很强的平面外织构；极图和φ扫描显示它具有良好的平面内织构. Ni基片上织构的CeO₂薄膜为进一步在其上外延高质量的YBa₂Cu₃O_7-x超导薄膜提供了很好的模板. 关键词： 双轴织构的Ni基带 2薄膜')" href="#">CeO₂薄膜 脉冲激光沉积     

线性微波化学气相沉积制备SiNx薄膜的微结构及光学性能研究

利用自主研发的线性微波化学气相沉积系统在不同微波功率、微波占空比、基片温度、特气比例条件下制备了SiN_x薄膜. 通过扫描电子显微镜、椭圆偏振仪等表征测量技术, 研究了不同工艺参数对SiN_x薄膜表面形貌、元素配比、折射率、沉积速度的影响, 并探讨了薄膜元素配比、折射率、沉积速度间的关系. 结果表明: 利用线性微波沉积技术, 不同工艺参数下制备的SiN_x薄膜组成元素分布均匀, 同时具有平整的表面状态; 特气比例和微波占空比是影响薄膜折射率的最主要因素, 薄膜折射率在1.92–2.33之间连续可调; 微波功率、微波占空比、沉积温度、特气比例都对SiN_x 薄膜沉积速度影响较大, 制备的SiN_x薄膜最大沉积速度为135 nm·min^-1.     

MgB2 超薄膜的制备和性质研究

利用混合物理化学气相沉积法在6H-SiC(001)衬底上制备干净的MgB₂超导超薄膜.在本底气体压强、载气氢气流量等条件一定的情况下,改变B₂H₆流量及沉积时间,制备得到不同厚度的系列MgB₂超薄膜样品,并研究了超导转变温度T_c、剩余电阻率ρ_(42K)、上临界磁场H_c2等与膜厚的关系.该系列超薄膜沿c轴外延生长,随膜厚度的变小,T_c(0)降低,ρ_(42K)升高.膜在衬底上的生长遵循Volmer-Weber岛状生长模式.对于厚度为7.5 nm的MgB₂超薄膜,T_c(0) =32.8 K,ρ_(42K) =118 μΩcm,是迄今为止所观测到的厚度为7.5 nm的MgB₂超薄膜最高的T_c值;对于厚度为10 nm的MgB₂膜,T_c(0)=35.5 K,ρ_(42K)=17.7 μΩcm,上临界磁场μ₀H_c2估算为12 T左右,零磁场、4 K时的临界电流密度J_c=1.0×10⁷ A/cm²,是迄今为止10 nm厚MgB₂超薄膜的最高J_c值,且其表面连接性良好,均方根粗糙度为0.731 nm.这预示MgB₂超薄膜在超导纳米器件上具有广阔的应用前景. 关键词： 2超薄膜')" href="#">MgB₂超薄膜 薄膜生长 氢气流量 混合物理化学气相沉积     

Preparation and photocatalytic property of CeO2 lamellar

A novel room temperature solid-state chemical synthesis was introduced to successfully fabricate CeO₂ samples, coupled by a polyethylene glycol 400 (PEG 400)/cetyl trimethylammonium bromide (CTAB)/sodium dodecyl sulfate (SDS). The as-prepared products were characterized by XRD, TEM, SEM, BET and UV. A study of photocatalytic degradation of the methylene blue MB under UV illumination has been carried out. It is indicated that the samples exhibit excellent photocatalytic activity. Besides, the samples assisted with surfactants possess higher photocatalytic activity than the sample without any surfactants, wherein the sample with SDS as an additive shows the highest photocatalytic activity, which is able to reach 89.6% MB degradation ratio within 60 min illumination. Moreover, the effects of important operational parameters such as initial MB concentration, catalyst loading and pH were also investigated. The above sample under the optimum conditions obtained the maximum MB degradation ratio up to 96.5%, which is higher than that of the commercial TiO₂ P25 under the same conditions. It can be concluded that CeO₂ will be a potential photocatalyst in the application of organic pollutant.     

Structural and optical properties of SrCu2O2 films deposited on sapphire substrates by pulsed laser deposition

We deposited SrCu₂O₂ (SCO) films on sapphire (Al₂O₃) (0 0 0 1) substrates by pulsed laser deposition. The crystallographic orientation of the SCO thin film showed clear dependence on the growth temperature. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis showed that the film deposited at 400 °C was mainly oriented in the SCO [2 0 0] direction, whereas when the growth temperature was increased to 600 °C, the SCO film showed a dominant orientation of SCO [1 1 2]. The SCO film deposited at 500 °C was obvious polycrystalline, showing multi peaks from (2 0 0), (1 1 2), and (2 1 1) diffraction in the XRD spectrum. The SCO film deposited at 600 °C showed a band gap energy of 3.3 eV and transparency up to 80% around 500 nm. The photoluminescence (PL) spectra of the SCO films grown at 500 °C and 600 °C mainly showed blue-green emission, which was attributed to the intra-band transition of the isolated Cu⁺ and Cu⁺–Cu⁺ pairs according to the temperature dependent-PL analysis.     

Nanomechanical characteristics of SnO2:F thin films deposited by chemical vapor deposition

The nanoindentation characterizations and mechanical properties of fluorine-doped tin oxide (SnO₂:F) films deposited on glass substrates, using chemical vapor deposition (CVD) method, were studied, which included the effects of the indentation loads, the loading time and the hold time on the thin film. The surface roughness, fractal dimension and frictional coefficient were also studied by varying the freon flow rates. X-ray diffraction (XRD), atomic force microscopy (AFM) and frictional force microscopy (FFM) were used to analyze the morphology of the microstructure. The results showed that crystalline structure of the film had a high intensity (1 1 0) peak orientation, especially at a low freon flow rate. According to the nanoindentation records, the Young's modulus ranged from 62.4 to 75.1 GPa and the hardness ranged from 5.1 to 9.9 GPa at a freon flow rate of 8000 sccm. The changes in measured properties were due to changing loading rate.     

Influence of deposition temperature on the structural and morphological properties of Be3N2 thin films grown by reactive laser ablation

Be₃N₂ thin films have been grown on Si(1 1 1) substrates using the pulsed laser deposition method at different substrate temperatures: room temperature (RT), 200 °C, 400 °C, 600 °C and 700 °C. Additionally, two samples were deposited at RT and were annealed after deposition in situ at 600 °C and 700 °C. In order to obtain the stoichiometry of the samples, they have been characterized in situ by X-ray photoelectron (XPS) and reflection electron energy loss spectroscopy (REELS). The influence of the substrate temperature on the morphological and structural properties of the films was investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD). The results show that all prepared films presented the Be₃N₂ stoichiometry. Formation of whiskers with diameters of 100-200 nm appears at the surface of the films prepared with a substrate temperature of 600 °C or 700 °C. However, the samples grown at RT and annealed at 600 °C or 700 °C do not show whiskers on the surface. The average root mean square (RMS) roughness and the average grain size of the samples grown with respect the substrate temperature is presented. The films grown with a substrate temperature between the room temperature to 400 °C, and the sample annealed in situ at 600 °C were amorphous; while the αBe₃N₂ phase was presented on the samples with a substrate temperature of 600 °C, 700 °C and that deposited with the substrate at RT and annealed in situ at 700 °C.     

Photocatalytic behavior of heavy La-doped TiO2 films deposited by pulsed laser deposition using non-sintered target

We have investigated the control of photocatalytic behavior under deposited conditions of non-sintered target of different molar ratios with TiO₂ and La₂O₃ from 1:0 to 1:2 for heavily La doping, and post-annealing temperature from 600 °C to 1000 °C for crystallizing by pulsed laser deposition. We have successfully crystallized heavily La-doped TiO₂ films with post-annealing temperature over 800 °C and with molar ratio of TiO₂:La₂O₃ over 1:1 on a quartz substrate. Heavily La-doped TiO₂ films are observed the decomposition of methylene blue and a water-splitting reaction in photocatalytic behavior under Xe light irradiation. When stoichiometric La-doped TiO₂ (TiO₂:La₂O₃ = 1: 1) is synthesized with heat-treatment at 900 °C, the best results are obtained under photocatalytic behavior and pure La₂Ti₂O₇ crystalline were obtained.     

Influence of [S2O3]/[Sm] on Sm2S3 thin films deposited by liquid phase deposition method on self-assembled monolayers

Sm₂S₃ thin films were prepared on Si (1 0 0) substrates using SmCl₃ and Na₂S₂O₃ as precursors by liquid phase deposition method on self-assembled monolayers. The influence of the molar concentration ratio of [S₂O₃²⁻]/[Sm³⁺] on the phase compositions, surface morphologies and optical properties of the as-deposited films were investigated. The as-deposited Sm₂S₃ thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), ultraviolet-visible (UV-vis) and photoluminescence spectrum (PL). Results show that it is important to control the [S₂O₃²⁻]/[Sm³⁺] during the deposition process and monophase Sm₂S₃ thin films with orientation growth along (0 1 1) direction can be achieved when [S₂O₃²⁻]/[Sm³⁺] = 2.0, pH 3.0, with citric acid as a template agent. The as-deposited thin films exhibit a dense and crystalline surface morphology. Good transmittance in the visible spectrum and excellent absorbency of ultraviolet light of the thin films are observed, and the band gap of the thin films first decrease and then increase with the increase of the [S₂O₃²⁻]/[Sm³⁺]. The as-deposited thin films also exhibit red photoluminescence properties under visible light excitation. With the increase of the [S₂O₃²⁻]/[Sm³⁺] in the deposition solution, the PL properties of Sm₂S₃ thin films are obviously improved.     

纳米TiO2薄膜的低温等离子体制备技术

以四氯化钛为源物质,氩气为载气,氧气为反应气体,利用低温等离子体增强化学气相沉积在硅基表面制备出了TiO2薄膜。使用场发射扫描电子显微镜、X射线衍射仪等检测分析表征TiO2薄膜的性能与性质,并探讨了工艺条件如基片材料、沉积时间和基片温度对薄膜性能的影响。结果表明：制备的薄膜表面光滑均匀,结构致密,最小晶粒尺寸约15 nm;薄膜的晶型主要依赖于沉积温度,低于300 ℃沉积的薄膜是无定形的,300 ℃之上沉积的薄膜是锐钛矿结构。     

Optical and gas sensing properties of thick TiO2 films grown by laser deposition

In this work the optical and the gas sensing properties of thick TiO₂ waveguide films, produced by pulsed laser deposition, were investigated by m-line spectroscopy. The films were deposited on (0 0 1) SiO₂ substrates at temperature of 100 °C. The thickness of the films was measured to be in the range from 650 to 1900 nm and the roughness increases from 5 to 14.6 nm. High quality mode spectra, consisted of thin and bright TE and TM modes, were observed in the films with thickness up to 1200 nm. All the films revealed anisotropic optical properties. Gas sensitivity of the films to CO₂ was examined at room temperature on the basis of the variations of the refractive index. CO₂ concentration of 3 × 10⁴ ppm was detected, which corresponds to a refractive index variation of about 1 × 10⁻⁴. The crystal structure and the optical transmittance of the films were also presented and discussed.     

Pulsed laser deposition of Bi2Te3 thermoelectric films

Bi₂Te₃ is one of the most used materials for thermoelectric applications at ambient temperature. An improvement of thermoelectric performances through a suitable modification of electron and phonon transport mechanisms is predicted for low dimensional or nanostructured systems, but this requires a control of the material structure down to the nanoscale. We show that pulsed laser deposition provides control on film composition, phase and structure, necessary for a comprehension of the relationship between structure and thermoelectric properties. We have explored the role of deposition temperature, background inert gas type and pressure, laser fluence and target-to-substrate distance and we found the experimental condition ranges to obtain crystalline films containing the Bi₂Te₃ phase only, by comparing energy dispersive X-ray spectroscopy, Raman spectroscopy and X-ray diffraction analysis. Variations of substrate temperature and deposition gas pressure prove to be crucial also for the control of film morphology and crystallinity. Substrate type has no influence on film stoichiometry and crystallinity, but highly oriented growth can be achieved on mica due to van der Waals epitaxy.     

Buffers for high temperature superconductor coatings. Low temperature growth of CeO2 films by metal–organic chemical vapor deposition and their implementation as buffers

Smooth, epitaxial cerium dioxide thin films have been grown in-situ in the 450–650°C temperature range on (001) yttria-stabilized zirconia (YSZ) substrates by metal–organic chemical vapor deposition (MOCVD) using a new fluorine-free liquid Ce precursor. As assessed by X-ray diffraction, transmission electron microscopy (TEM), and high-resolution electron microscopy (HREM), the epitaxial films exhibit a columnar microstructure with atomically abrupt film-substrate interfaces and with only minor bending of the crystal plane parallel to the substrate surface near the interface and at the column boundaries. With fixed precursor temperature and gas flow rate, the CeO₂ growth rate decreases from 10 Å/min at 450°C to 6.5 Å/min at 540°C. The root-mean-square roughness of the films also decreases from 15.5 Å at 450°C to 4.3 Å at 540°C. High-quality, epitaxial YBa₂C₃O_7−x films have been successfully deposited on these MOCVD-derived CeO₂ films grown at temperatures as low as 540°C. They exhibit T_c=86.5 K and J_c=1.08×10⁶ A/cm² at 77.4 K.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Preparation of photocatalytic Fe2O3-TiO2 coatings in one step by metal organic chemical vapor deposition

There are two major difficulties in the TiO₂ liquid-solid photocatalytic system: effective immobilization of the TiO₂ particles; and improving the catalytic activity under visible light. To simultaneously solve these two problems, Fe₂O₃-TiO₂ coatings supported on activated carbon fiber (ACF), have been prepared in one step by a convenient and efficient method—metal organic chemical vapor deposition (MOCVD). XRD results revealed that Fe₂O₃-TiO₂ coatings mainly composed of anatase TiO₂, α-Fe₂O₃ phases and little Fe₂Ti₃O₉. The pore structure of ACF was preserved well after loading with Fe₂O₃-TiO₂ coatings. UV-vis diffuse reflectance spectra showed a slight shift to longer wavelengths and an enhancement of the absorption in the visible region for Fe₂O₃-TiO₂ coatings, compared to the pure TiO₂ sample. A moderate Fe₂O₃-TiO₂ loading (13.7 wt%) was beneficial to mineralizing wastewater because the intermediates could be adsorbed onto the surface of photocatalyst following decomposition. The stable performance revealed that the Fe₂O₃-TiO₂ coatings were strongly adhered to the ACF surface, and the as prepared catalysts could be reused showing potential application for wastewater treatment.     

Influence of different oxidants on band alignment of HfO2 films deposited by atomic layer deposition

Based on X-ray photoelectron spectroscopy (XPS), influences of different oxidants on band alignment of HfO₂ films deposited by atomic layer deposition (ALD) are investigated in this paper. The measured valence band offset (VBO) value for H₂O-based HfO₂ increases from 3.17 eV to 3.32 eV after annealing, whereas the VBO value for O₃-based HfO₂ decreases from 3.57 eV to 3.46 eV. The research results indicate that the silicate layer changes in different ways for H₂O-based and O₃-based HfO₂ films after annealing process, which plays a key role in generating the internal electric field formed by the dipoles. The variations of the dipoles at the interface between the HfO₂ and SiO₂ after annealing may lead the VBO values of H₂O-based and O₃-based HfO₂ to vary in different ways, which is in agreement with the varition of flat band (V_FB) voltage.     

Uniform thin films of TiO2 nanoparticles deposited by matrix-assisted pulsed laser evaporation

We report morphological and optical properties of a colloidal TiO₂ nanoparticle film, deposited on a quartz substrate by using the Matrix-Assisted Pulsed Laser Evaporation (MAPLE) technique. Atomic Force Microscopy demonstrated that a good uniformity of the deposition can be obtained. The presence of agglomerates with dimensions of about 1 μm in size was noticed. Form UV-vis transmission spectra, recorded in the 200-800 nm range, the optical constants and the energy gap were determined besides the film thickness. The optical constants resulted in agreement with the values reported in literature for TiO₂ nanoparticle thin films.     

Effects of oxygen vacancies on the room-temperature ferromagnetism of Co-doped polycrystalline CeO2

Pure and Co-doped single-phase CeO₂ crystals were synthesized by a solid-state reaction method. Samples of different oxygen vacancy concentration were studied, including (1) as-sintered crystals, (2) powders ground from the same crystal, and (3) a cold-pressed pellet from the ground powder that was unannealed and annealed at 800 °C. By analyzing the magnetic behaviors, surface/volume ratio and O vacancy concentration, the effects of oxygen vacancies on the room-temperature ferromagnetism (RT-FM) of Co-doped CeO₂ were systematically investigated. The results confirm that the RT-FM observed in Co-doped CeO₂ has a direct relationship with the oxygen vacancy concentration, and support the oxygen vacancy mediated FM mechanism.     

Laser spectroscopy of CaF2:Eu:Sm thin films grown by pulsed laser deposition

Thin films of CaF₂ co-doped with low concentrations of Eu and Sm ions were grown by pulsed laser deposition (PLD) using a KrF (λ=248 nm) as the ablation source. To the best of our knowledge, the work presented here is the first report of rare-earth-doped CaF₂ films grown by PLD with this source. Combined laser excitation-emission spectroscopy was used to map out electronic transitions of Eu³⁺ with ⁷F₀→⁵D₁ excitation and the ⁵D₀→⁷F₁ emission. At the low concentrations used here the crystal field center of cubic symmetry is dominant in the films that are same for laser targets. However, charge compensated centers are present in the bulk crystal precursor. The removal of the charge compensated centers in the films and the target is likely caused by the target preparation where high pressure and temperature were applied.     

脉冲激光沉积温度及氧压对Bi2Sr2Co2Oy热电薄膜晶体结构与电输运性能的影响

利用脉冲激光沉积技术在c-Al₂O₃单晶基片上制备了Bi₂Sr₂Co₂O_y热电薄膜并研究了沉积温度和氧压对薄膜晶体结构及电输运性能的影响.在最佳沉积条件下制备的单相、c轴取向的Bi₂Sr₂Co₂O_y薄膜的室温电阻率ρ和塞贝克系数S分别为2.9mΩ/cm和110μupV/K,其功率因子S²/ρ好于在单晶样品上得到的值.此外,该薄膜在低温下表现出较强的负磁阻效应,在2K,9T时达到了40%.