Carbonyl-rich Poly(pyrene-4,5,9,10-tetraone Sulfide) as Anode Materials for High-Performance Li and Na-Ion Batteries

Organic carbonyl electrode materials are widely employed for alkali metal-ion secondary batteries in terms of their sustainability, structure designability and abundant resources. As a typical redox-active organic electrode materials, pyrene-4, 5, 9, 10-tetraone (PT) shows high theoretical capacity due to the rich carbonyl active sites. But its electrochemical behavior in secondary batteries still needs further exploration. Herein, PT-based linear polymers (PPTS) is synthesized with thioether bond as bridging group and then employed as an anode material for lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs). As expected, PPTS shows improved conductivity and insolubility in the non-aqueous electrolyte. When used as an anode material for LIBs, PPTS delivers a high reversible specific capacity of 697.1 mAh g⁻¹ at 0.1 A g⁻¹ and good rate performance (335.4 mAh g⁻¹ at 1 A g⁻¹). Moreover, a reversible specific capacity of 205.2 mAh g⁻¹ at 0.05 A g⁻¹ could be obtained as an anode material for SIBs.     

Multiple Active Sites: Lithium Storage Mechanism of Cu‐TCNQ as an Anode Material for Lithium‐Ion Batteries

Recently, carboxylate metal‐organic framework (MOF) materials were reported to perform well as anode materials for lithium‐ion batteries (LIBs); however, the presumed lithium storage mechanism of MOFs is controversial. To gain insight into the mechanism of MOFs as anode materials for LIBs, a self‐supported Cu‐TCNQ (TCNQ: 7,7,8,8‐tetracyanoquinodimethane) film was fabricated via an in situ redox routine, and directly used as electrode for LIBs. The first discharge and charge specific capacities of the self‐supported Cu‐TCNQ electrode are 373.4 and 219.4 mAh g^?1, respectively. After 500 cycles, the reversible specific capacity of Cu‐TCNQ reaches 280.9 mAh g^?1 at a current density of 100 mA g^?1. Mutually validated data reveal that the high capacity is ascribed to the multiple‐electron redox conversion of both metal ions and ligands, as well as the reversible insertion and desertion of Li⁺ ions into the benzene rings of ligands. This work raises the expectation for MOFs as electrode materials of LIBs by utilizing multiple active sites and provides new clues for designing improved electrode materials for LIBs.     

Two-Dimensional Germanium Sulfide Nanosheets as an Ultra-Stable and High Capacity Anode for Lithium Ion Batteries

Lithium ion batteries (LIBs) at present still suffer from low rate capability and poor cycle life during fast ion insertion/extraction processes. Searching for high-capacity and stable anode materials is still an ongoing challenge. Herein, a facile strategy for the synthesis of ultrathin GeS₂ nanosheets with the thickness of 1.1 nm is reported. When used as anodes for LIBs, the two-dimensional (2D) structure can effectively increase the electrode/electrolyte interface area, facilitate the ion transport, and buffer the volume expansion. Benefiting from these merits, the as-synthesized GeS₂ nanosheets deliver high specific capacity (1335 mAh g⁻¹ at 0.15 A g⁻¹), extraordinary rate performance (337 mAh g⁻¹ at 15 A g⁻¹) and stable cycling performance (974 mAh g⁻¹ after 200 cycles at 0.5 A g⁻¹). Importantly, our fabricated Li-ion full cells manifest an impressive specific capacity of 577 mAh g⁻¹ after 50 cycles at 0.1 A g⁻¹ and a high energy density of 361 Wh kg⁻¹ at a power density of 346 W kg⁻¹. Furthermore, the electrochemical reaction mechanism is investigated by the means of ex-situ high-resolution transmission electron microscopy. These results suggest that GeS₂ can use to be an alternative anode material and encourage more efforts to develop other high-performance LIBs anodes.     

Vertically Grown Few-Layer MoS2 Nanosheets on Hierarchical Carbon Nanocages for Pseudocapacitive Lithium Storage with Ultrahigh-Rate Capability and Long-Term Recyclability

Molybdenum disulfide (MoS₂) is an intensively studied anode material for lithium-ion batteries (LIBs) owing to its high theoretical capacity, but it is still confronted by severe challenges of unsatisfactory rate capability and cycle life. Herein, few-layer MoS₂ nanosheets, vertically grown on hierarchical carbon nanocages (hCNC) by a facile hydrothermal method, introduce pseudocapacitive lithium storage owing to the highly exposed MoS₂ basal planes, enhanced conductivity, and facilitated electrolyte access arising from good hybridization with hCNC. Thus, the optimized MoS₂/hCNC exhibits reversible capacities of 1670 mAh g⁻¹ at 0.1 A g⁻¹ after 50 cycles, 621 mAh g⁻¹ at 5.0 A g⁻¹ after 500 cycles, and 196 mAh g⁻¹ at 50 A g⁻¹ after 2500 cycles, which are among the best for MoS₂-based anode materials. The specific power and specific energy, which can reach 16.1 kW and 252.8 Wh after 3000 cycles, respectively, indicate great potential in high-power and long-life LIBs. These findings suggest a promising strategy for exploring advanced anode materials with high reversible capacity, high-rate capability, and long-term recyclability.     

Pseudocapacitive Lithium Storage of Cauliflower-Like CoFe2O4 for Low-Temperature Battery Operation

Binary transition-metal oxides (BTMOs) with hierarchical micro–nano-structures have attracted great interest as potential anode materials for lithium-ion batteries (LIBs). Herein, we report the fabrication of hierarchical cauliflower-like CoFe₂O₄ (cl-CoFe₂O₄) via a facile room-temperature co-precipitation method followed by post-synthetic annealing. The obtained cauliflower structure is constructed by the assembly of microrods, which themselves are composed of small nanoparticles. Such hierarchical micro–nano-structure can promote fast ion transport and stable electrode–electrolyte interfaces. As a result, the cl-CoFe₂O₄ can deliver a high specific capacity (1019.9 mAh g⁻¹ at 0.1 A g⁻¹), excellent rate capability (626.0 mAh g⁻¹ at 5 A g⁻¹), and good cyclability (675.4 mAh g⁻¹ at 4 A g⁻¹ for over 400 cycles) as an anode material for LIBs. Even at low temperatures of 0 °C and −25 °C, the cl-CoFe₂O₄ anode can deliver high capacities of 907.5 and 664.5 mAh g⁻¹ at 100 mA g⁻¹, respectively, indicating its wide operating temperature. More importantly, the full-cell assembled with a commercial LiFePO₄ cathode exhibits a high rate performance (214.2 mAh g⁻¹ at 5000 mA g⁻¹) and an impressive cycling performance (612.7 mAh g⁻¹ over 140 cycles at 300 mA g⁻¹) in the voltage range of 0.5–3.6 V. Kinetic analysis reveals that the electrochemical performance of cl-CoFe₂O₄ is dominated by pseudocapacitive behavior, leading to fast Li⁺ insertion/extraction and good cycling life.     

Hierarchical Hollow-Nanocube Ni−Co Skeleton@MoO3/MoS2 Hybrids for Improved-Performance Lithium-Ion Batteries

Improving the performance of anode materials for lithium-ion batteries (LIBs) is a hotly debated topic. Herein, hollow Ni−Co skeleton@MoS₂/MoO₃ nanocubes (NCM-NCs), with an average size of about 193 nm, have been synthesized through a facile hydrothermal reaction. Specifically, MoO₃/MoS₂ composites are grown on Ni−Co skeletons derived from nickel–cobalt Prussian blue analogue nanocubes (Ni−Co PBAs). The Ni−Co PBAs were synthesized through a precipitation method and utilized as self-templates that provided a larger specific surface area for the adhesion of MoO₃/MoS₂ composites. According to Raman spectroscopy results, as-obtained defect-rich MoS₂ is confirmed to be a metallic 1T-phase MoS₂. Furthermore, the average particle size of Ni−Co PBAs (≈43 nm) is only about one-tenth of the previously reported particle size (≈400 nm). If assessed as anodes of LIBs, the hollow NCM-NC hybrids deliver an excellent rate performance and superior cycling performance (with an initial discharge capacity of 1526.3 mAh g⁻¹ and up to 1720.6 mAh g⁻¹ after 317 cycles under a current density of 0.2 A g⁻¹). Meanwhile, ultralong cycling life is retained, even at high current densities (776.6 mAh g⁻¹ at 2 A g⁻¹ after 700 cycles and 584.8 mAh g⁻¹ at 5 A g⁻¹ after 800 cycles). Moreover, at a rate of 1 A g⁻¹, the average specific capacity is maintained at 661 mAh g⁻¹. Thus, the hierarchical hollow NCM-NC hybrids with excellent electrochemical performance are a promising anode material for LIBs.     

Hybrid Sub-1 nm Nanosheets of Co-assembled MnZnCuOx and Polyoxometalate Clusters as Anodes for Li-ion Batteries

Transition metal oxide (TMO) anode materials in lithium-ion batteries (LIBs) usually suffer from serious volume expansion leading to the pulverization of structures, further giving rise to lower specific capacity and worse cycling stability. Herein, by introducing polyoxometalate (POM) clusters into TMOs and precisely controlling the amount of POMs, the MnZnCuO_x-phosphomolybdic acid hybrid sub-1 nm nanosheets (MZC-PMA HSNSs) anode is successfully fabricated, where the special electron rich structure of POMs is conducive to accelerating the migration of lithium ions on the anode to obtain higher specific capacity, and the non-covalent interactions between POMs and TMOs make the HSNSs possess excellent structural and chemical stability, thus exhibiting outstanding electrochemical performance in LIBs, achieving a high reversible capacity (1157 mAh g⁻¹ at 100 mA g⁻¹) and an admirable long-term cycling stability at low and high current densities.     

Synthesis of Co3O4/CoOOH via electrochemical dispersion using a pulse alternating current method for lithium-ion batteries and supercapacitors

We report a convenient, low-cost and ecofriendly approach for the fabrication of a Co₃O₄/CoOOH electrode material intended for lithium ion batteries (LIBs) and supercapacitors (SCs) using the electrochemical dispersion of the cobalt foil through the pulse alternating current (PAC) method. The synthesized material is a Co₃O₄/CoOOH composite (with about 10–15 wt% CoOOH) in the form of nanosheets with a length of approximately 200 nm and a thickness of 10–20 nm. It is found to exhibit high reversible discharge specific capacities and good cycling behavior while tested as the anode material in LIBs. Measuring the reversible capacitance at high (2C) and low (C/20) cycling rates gives the values of 610 mAh g⁻¹ and 1030 mAh g⁻¹, respectively. The specimen possesses excellent performance as the electrode for SCs with the retention of capacitance up to 98% at the current density increasing from 0.5 to 10 A g⁻¹. After 1000 cycles at a current density of 10 A g⁻¹ the electrode maintains about 90% of its initial capacitance which evidences the long cycle life. Hence, electrochemically prepared Co₃O₄/CoOOH seems to be a promising candidate for high-performance LIBs and SCs applications.     

Scalable Synthesis of Porous SiFe@C Composite with Excellent Lithium Storage

Utilizing cost-effective raw materials to prepare high-performance silicon-based anode materials for lithium-ion batteries (LIBs) is both challenging and attractive. Herein, a porous SiFe@C (pSiFe@C) composite derived from low-cost ferrosilicon is prepared via a scalable three-step procedure, including ball milling, partial etching, and carbon layer coating. The pSiFe@C material integrates the advantages of the mesoporous structure, the partially retained FeSi₂ conductive phase, and a uniform carbon layer (12–16 nm), which can substantially alleviate the huge volume expansion effect in the repeated lithium-ion insertion/extraction processes, effectively stabilizing the solid–electrolyte interphase (SEI) film and markedly enhancing the overall electronic conductivity of the material. Benefiting from the rational structure, the obtained pSiFe@C hybrid material delivers a reversible capacity of 1162.1 mAh g⁻¹ after 200 cycles at 500 mA g⁻¹, with a higher initial coulombic efficiency of 82.30 %. In addition, it shows large discharge capacities of 803.1 and 600.0 mAh g⁻¹ after 500 cycles at 2 and 4 A g⁻¹, respectively, manifesting an excellent electrochemical lithium storage. This work provides a good prospect for the commercial production of silicon-based anode materials for LIBs with a high lithium-storage capacity.     

Scalable Synthesis of One-Dimensional Mesoporous ZnMnO3 Nanorods with Ultra-Stable and High Rate Capability for Efficient Lithium Storage

The cost-efficient ZnMnO₃ has attracted increasing attention as a prospective anode candidate for advanced lithium-ion batteries (LIBs) owing to its resourceful abundance, large lithium storage capacity and low operating voltage. However, its practical application is still seriously limited by the modest cycling and rate performances. Herein, a facile design to scalable synthesize unique one-dimensional (1D) mesoporous ZnMnO₃ nanorods (ZMO-NRs) composed of nanoscale particles (≈11 nm) is reported. The 1D mesoporous structure and nanoscale building blocks of the ZMO-NRs effectively promote the transport of ions/electrons, accommodate severe volume changes, and expose more active sites for lithium storage. Benefiting from these appealing structural merits, the obtained ZMO-NRs anode exhibits excellent rate behavior (≈454 mAh g⁻¹ at 2 A g⁻¹) and ultra-long term cyclic performance (≈949.7 mAh g⁻¹ even over 500 cycles at 0.5 A g⁻¹) for efficient lithium storage. Additionally, the LiNi_0.8Co_0.1Mn_0.1O₂//ZMO-NRs full cell presents a practical energy density (≈192.2 Wh kg⁻¹) and impressive cyclability with approximately 91 % capacity retention over 110 cycles. This highlights that the ZMO-NRs product is a highly promising high-rate and stable electrode candidate towards advanced LIBs in electronic devices and sustainable energy storage applications.     

Advanced Li-Ion Batteries with High Rate,Stability, and Mass Loading Based on Graphene Ribbon Hybrid Networks

To optimize the cycle life and rate performance of lithium-ion batteries (LIBs), ultra-fine Fe₂O₃ nanowires with a diameter of approximately 2 nm uniformly anchored on a cross-linked graphene ribbon network are fabricated. The unique three-dimensional structure can effectively improve the electrical conductivity and facilitate ion diffusion, especially cross-plane diffusion. Moreover, Fe₂O₃ nanowires on graphene ribbons (Fe₂O₃/GR) are easily accessible for lithium ions compared with the traditional graphene sheets (Fe₂O₃/GS). In addition, the well-developed elastic network can not only undergo the drastic volume expansion during repetitive cycling, but also protect the bulk electrode from further pulverization. As a result, the Fe₂O₃/GR hybrid exhibits high rate and long cycle life Li storage performance (632 mAh g⁻¹ at 5 A g⁻¹, and 471 mAh g⁻¹ capacity maintained even after 3000 cycles). Especially at high mass loading (≈4 mg cm⁻²), the Fe₂O₃/GR can still deliver higher reversible capacity (223 mAh g⁻¹ even at 2 A g⁻¹) compared with the Fe₂O₃/GS (37 mAh g⁻¹) for LIBs.     

Few-Layer MoS2 Nanosheets Encapsulated in N-Doped Carbon Hollow Spheres as Long-Life Anode Materials for Lithium-Ion Batteries

Two-dimensional molybdenum disulfide (MoS₂) has been recognized as a promising anode material for lithium-ion batteries (LIBs) due to its high theoretical capacity, but its rapid capacity decay owing to poor conductivity, structure pulverization, and polysulfide dissolution presents significant challenges in practical applications. Herein, triple-layered hollow spheres in which MoS₂ nanosheets are fully encapsulated between inner carbon and outer nitrogen-doped carbon (NC) were fabricated. Such an architecture provides high conductivity and efficient lithium-ion transfer. Moreover, the NC shell prevents aggregation and exfoliation of MoS₂ nanosheets and thus maintains the integrity of the nanostructure during the charge/discharge process. As anode materials for LIBs, the C@MoS₂@NC hollow spheres deliver a high reversible capacity (747 mA h g⁻¹ after 100 cycles at 100 mA g⁻¹) and excellent long-cycle performance (650 mA h g⁻¹ after 1000 cycles at 1.0 A g⁻¹), which confirm its potential for high-performance LIBs.     

Facile Synthesis of Ultra-Small Few-Layer Nanostructured MoSe2 Embedded on N,P Co-Doped Bio-Carbon for High-Performance Half/Full Sodium-Ion and Potassium-Ion Batteries

Sodium/potassium-ion batteries (SIBs/PIBs) arouse intensive interest on account of the natural abundance of sodium/potassium resources, the competitive cost and appropriate redox potential. Nevertheless, the huge challenge for SIBs/PIBs lies in the scarcity of an anode material with high capacity and stable structure, which are capable of accommodating large-size ions during cycling. Furthermore, using sustainable natural biomass to fabricate electrodes for energy storage applications is a hot topic. Herein, an ultra-small few-layer nanostructured MoSe₂ embedded on N, P co-doped bio-carbon is reported, which is synthesized by using chlorella as the adsorbent and precursor. As a consequence, the MoSe₂/NP-C-2 composite represents exceedingly impressive electrochemical performance for both sodium-ion batteries (SIBs) and potassium-ion batteries (PIBs). It displays a promising reversible capacity (523 mAh g⁻¹ at 100 mA g⁻¹ after 100 cycles) and impressive long-term cycling performance (192 mAh g⁻¹ at 5 A g⁻¹ even after 1000 cycles) in SIBs, which are some of the best properties of MoSe₂-based anode materials for SIBs to date. To further probe the great potential applications, full SIBs pairing the MoSe₂/NP-C-2 composite anode with a Na₃V₂(PO₄)₃ cathode also exhibits a satisfactory capacity of 215 mAh g⁻¹ at 500 mA g⁻¹ after 100 cycles. Moreover, it also delivers a decent reversible capacity of 131 mAh g⁻¹ at 1 A g⁻¹ even after 250 cycles for PIBs.     

Porous ZnO/Co3O4/N‐doped carbon nanocages synthesized via pyrolysis of complex metal–organic framework (MOF) hybrids as an advanced lithium‐ion battery anode

Metal oxides have a large storage capacity when employed as anode materials for lithium‐ion batteries (LIBs). However, they often suffer from poor capacity retention due to their low electrical conductivity and huge volume variation during the charge–discharge process. To overcome these limitations, fabrication of metal oxides/carbon hybrids with hollow structures can be expected to further improve their electrochemical properties. Herein, ZnO‐Co₃O₄ nanocomposites embedded in N‐doped carbon (ZnO‐Co₃O₄@N‐C) nanocages with hollow dodecahedral shapes have been prepared successfully by the simple carbonizing and oxidizing of metal–organic frameworks (MOFs). Benefiting from the advantages of the structural features, i.e. the conductive N‐doped carbon coating, the porous structure of the nanocages and the synergistic effects of different components, the as‐prepared ZnO‐Co₃O₄@N‐C not only avoids particle aggregation and nanostructure cracking but also facilitates the transport of ions and electrons. As a result, the resultant ZnO‐Co₃O₄@N‐C shows a discharge capacity of 2373 mAh g^?1 at the first cycle and exhibits a retention capacity of 1305 mAh g^?1 even after 300 cycles at 0.1 A g^?1. In addition, a reversible capacity of 948 mAh g^?1 is obtained at a current density of 2 A g^?1, which delivers an excellent high‐rate cycle ability.     

In Situ Nitrogen Retention of Carbon Anode for Enhancing the Electrochemical Performance for Sodium-Ion Battery

Retaining nitrogen for polyacrylonitrile (PAN) based carbon anode is a cost-effective way to make full use of the advantages of PAN for sodium-ion batteries (SIBs). Here, a simple strategy has been successfully adopted to retain N atoms in situ and increase production yield of a novel composite PAZ by mixing 3 wt % of zinc borate (ZB) with poly (acrylonitrile-co-itaconic acid) (PANIA). Among the prepared carbonised fibre (CF) samples, PAZ-CF-700 maintains the highest N content, retaining 90 % of the original N from PANIA. It represents the highest capacity storage contribution (80.55 %) and the lowest impedance R_ct (117 Ω). Consequently, the specific capacity increases from 60 mAh g⁻¹ of PANIA-CF-700 to 190 mAh g⁻¹ of PAZ-CF-700 at a current density of 100 mA g⁻¹. At the same time, PAZ-CF-700 exhibits a good rate performance and excellent long-term cycling stability with a specific capacity of 94 mAh g⁻¹ after 4000 cycles at 1.6 A g⁻¹.     

Metal–Organic Frameworks-Derived Mesoporous Si/SiOx@NC Nanospheres as a Long-Lifespan Anode Material for Lithium-Ion Batteries

Silicon (Si)-based anode materials with suitable engineered nanostructures generally have improved lithium storage capabilities, which provide great promise for the electrochemical performance in lithium-ion batteries (LIBs). Herein, a metal–organic framework (MOF)-derived unique core–shell Si/SiO_x@NC structure has been synthesized by a facile magnesio-thermic reduction, in which the Si and SiO_x matrix were encapsulated by nitrogen (N)-doped carbon. Importantly, the well-designed nanostructure has enough space to accommodate the volume change during the lithiation/delithiation process. The conductive porous N-doped carbon was optimized through direct carbonization and reduction of SiO₂ into Si/SiO_x simultaneously. Benefiting from the core–shell structure, the synthesized product exhibited enhanced electrochemical performance as an anode material in LIBs. Particularly, the Si/SiO_x@NC-650 anode showed the best reversible capacities up to 724 and 702 mAh g⁻¹ even after 100 cycles. The excellent cycling stability of Si/SiO_x@NC-650 may be attributed to the core–shell structure as well as the synergistic effect between the Si/SiO_x and MOF-derived N-doped carbon.     

A Self‐Standing and Flexible Electrode of Yolk–Shell CoS2 Spheres Encapsulated with Nitrogen‐Doped Graphene for High‐Performance Lithium‐Ion Batteries

Flexible lithium‐ion batteries (LIBs) have recently attracted increasing attention with the fast development of bendable electronic systems. Herein, a facile and template‐free solvothermal method is presented for the fabrication of hybrid yolk–shell CoS₂ and nitrogen‐doped graphene (NG) sheets. The yolk–shell architecture of CoS₂ encapsulated with NG coating is designed for the dual protection of CoS₂ to address the structural and interfacial stability concerns facing the CoS₂ anode. The as‐prepared composite can be assembled into a film, which can be used as a binder‐free and flexible electrode for LIBs that does not require any carbon black conducting additives or current collectors. When evaluating lithium‐storage properties, such a flexible electrode exhibits a high specific capacity of 992 mAh g^?1 in the first reversible discharge capacity at a current rate of 100 mA g^?1 and high reversible capacity of 882 mAh g^?1 after 150 cycles with excellent capacity retention of 89.91 %. Furthermore, a reversible capacity as high as 655 mAh g^?1 is still achieved after 50 cycles even at a high rate of 5 C due to the yolk–shell structure and NG coating, which not only provide short Li‐ion and electron pathways, but also accommodate large volume variation.     

Boosting Fe Cationic Vacancies with Graphdiyne to Enhance Exceptional Pseudocapacitive Lithium Intercalation

Modulating the electronic structure of electrode materials at atomic level is the key to controlling electrodes with outstanding rate capability. On the basis of modulating the iron cationic vacancies (IV) and electronic structure of materials, we proposed the method of preparing graphdiyne/ferroferric oxide heterostructure (IV-GDY-FO) as anode materials. The goal is to motivate lithium-ion batteries (LIBs) toward ultra-high capacity, superior cyclic stability, and excellent rate performance. The graphdiyne is used as carriers to disperse Fe₃O₄ uniformly without agglomeration and induce high valence of Fe with reducing the energy in the system. The presence of Fe vacancy could regulate the charge distribution around vacancies and adjacent atoms, leading to facilitate electronic transportation, enlarge the lithium-ion diffusion, and decrease Li⁺ diffusion barriers, and thus displaying significant pseudocapacitive process and advantageous lithium-ion storage. The optimized electrode IV-GDY-FO reveals a capacity of 2084.1 mAh g⁻¹ at 0.1 C, superior cycle stability and rate performance with a high specific capacity of 1057.4 mAh g⁻¹ even at 10 C.     

Two π-Conjugated Covalent Organic Frameworks with Long-Term Cyclability at High Current Density for Lithium Ion Battery

Organic lithium ion batteries (LIBs) are considered as one of the next-generation green electrochemical energy storage (EES) devices. However, obtaining both high capacity and long-term cyclability is still the bottleneck of organic electrode materials for LIBs because of weak structural and chemical stability and low conductivity. Covalent organic frameworks (COFs) show potential to overcome these problems owing to its good stability and high capacity. Herein, the synthesis and characterization of two π-conjugated COFs, derived from the Schiff-base reaction of 2,4,6-triaminopyrimidne (TM) respectively with 1,4-phthalaldehyde (PA) and 1,3,5-triformylbenzene (TB) by a mechanochemical process are presented. As anode materials for LIBs, the COFs exhibit favorable electrochemical performance with the highest reversible discharge capacities of up to 401.3 and 379.1 mAh g⁻¹ at a high current density (1 A g⁻¹), respectively, and excellent long-term cyclability with 74.8 and 72.7 % capacity retention after 2000 cycles compared to the initial discharge capacities.     

Study of the Lithium Storage Mechanism of N-Doped Carbon-Modified Cu2S Electrodes for Lithium-Ion Batteries

Owing to their high specific capacity and abundant reserve, Cu_xS compounds are promising electrode materials for lithium-ion batteries (LIBs). Carbon compositing could stabilize the Cu_xS structure and repress capacity fading during the electrochemical cycling, but the corresponding Li⁺ storage mechanism and stabilization effect should be further clarified. In this study, nanoscale Cu₂S was synthesized by CuS co-precipitation and thermal reduction with polyelectrolytes. High-temperature synchrotron radiation diffraction was used to monitor the thermal reduction process. During the first cycle, the conversion mechanism upon lithium storage in the Cu₂S/carbon was elucidated by operando synchrotron radiation diffraction and in situ X-ray absorption spectroscopy. The N-doped carbon-composited Cu₂S (Cu₂S/C) exhibits an initial discharge capacity of 425 mAh g⁻¹ at 0.1 A g⁻¹, with a higher, long-term capacity of 523 mAh g⁻¹ at 0.1 A g⁻¹ after 200 cycles; in contrast, the bare CuS electrode exhibits 123 mAh g⁻¹ after 200 cycles. Multiple-scan cyclic voltammetry proves that extra Li⁺ storage can mainly be ascribed to the contribution of the capacitive storage.