Thermal, electrical, and electrochemical properties of Lanthanum-doped Ba0.5Sr0.5 Co0.8Fe0.2O3-δ

Crystal structure, thermogravimetry (TG), thermal expansion coefficient (TEC), electrical conductivity and AC impedance of (Ba_0.5Sr_0.5)_1-xLa_xCo_0.8Fe_0.2O_3-δ (BSLCF; 0.05?x?0.20) were studied in relation to their potential use as intermediate temperature solid oxide fuel cell (IT-SOFC) cathode. A single cubic pervoskite was observed by X-ray diffraction (XRD). The TEC of BSLCF was increasing slightly with the increasing content of La, and all the compounds showed abnormal expansion at high temperature. Proved by the TG result, it was associated with the loss of lattice oxygen. The electrical conductivity, which is the main defect of Ba_0.5Sr_0.5 Co_0.8Fe_0.2O_3-δ (BSCF), was improved by La doping, e.g., the compound of x=0.20 demonstrated a conductivity of σ=376 S cm⁻¹ at 392 °C. The increase of electrical conductivity resulted from the increased concentration of charge carrier induced by La doping. In addition, the AC impedance revealed the better electrochemical performance of BSLCF. For example, at 500 °C, the sample with composition x=0.15 yielded the resistance values of 2.12 Ω cm², which was only 46% of BSCF.     

Defect formation and transport in mixed-conducting La0.90Sr0.10Al0.85−xFexMg0.15O3−δ

The redox behavior of perovskite-type La_0.90Sr_0.10Al_0.85−xFe_xMg_0.15O_3−δ (x=0.20-0.40) mixed conductors was analyzed by the Mössbauer spectroscopy and measurements of the total conductivity and Seebeck coefficient in the oxygen partial pressure range from 10⁻²⁰ to 0.5 atm at 1023-1223 K. The results combined with oxygen-ion transference numbers determined by the faradaic efficiency technique in air, were used to calculate defect concentrations, mobilities, and partial ionic and p- and n-type electronic conductivities as a function of oxygen pressure. The redox and transport processes can be adequately described in terms of oxygen intercalation and iron disproportionation reactions, with the thermodynamic functions independent of defect concentrations. No essential delocalization of the electronic charge carriers was found. The oxygen non-stoichiometry values estimated from the conductivity vs. p(O₂) dependencies, coincide with those evaluated from the Mössbauer spectra.     

Electrical conductivity of (Er,U)O2+x and (Ce,U)O2+x

The electrical conductivity (σ) of (Er_yU_1−y)O_2+x (y=0.06, 0.20) and (Ce_yU_1−y)O_2+x (y=0.05, 0.15, 0.25) has been measured as a function of oxygen partial pressure in the temperature range of 1100≤T/°C≤1300 by a d.c. 4-probe method. Both of the oxides exhibited Po₂-regions where the electrical conductivity is independent of oxygen partial pressure, which indicates that doped Er and Ce exist as trivalent cations on uranium sites and fix the hole concentration by acting as electron acceptors, i.e. [h]=[Er′_U] and [h]=[Ce′_U], respectively. It is considered that strong oxidization tendency of uranium and reduction tendency of cerium simultaneously render the cerium ions exist exclusively as Ce³⁺ in the uranium dioxide. The electron-hole mobility of (Er_yU_1−y)O_2+x and (Ce_yU_1−y)O_2+x in the Po₂ region where σ is constant has been calculated by the combination of the electrical conductivity and charge carrier concentration; the activation energy (E_H) of each oxide has been obtained from the temperature dependence of the mobility. Small polaron hopping conduction mechanism was confirmed by small magnitude of the mobility (0.018-0.052 cm² V⁻¹ s⁻¹) and the activation energy (0.12-0.22 eV).     

Highly cation-deficient manganese perovskite, La1−xMn1−yO3 with x=y

Oxidative (δ>0) nonstoichiometry in the perovskite ‘LaMnO_3+δ’ has been known to be manifested not with O interstitials but rather with cation vacancies of equal amounts at the two cation sites, La and Mn, i.e. La_1−xMn_1−yO₃ with x=y. Here, we report the fabrication of samples with record-high cation-vacancy concentrations (x>0.12 or δ>0.4) by means of a variety of high-pressure oxygenation techniques. Linear (negative) dependence of the cell volume on x was observed within the whole x range investigated, down to 56.9 Å³ (per formula unit) for a sample oxygenated at 5 GPa and 1100 °C using Ag₂O₂ as an excess oxygen source. With increasing degree of cation deficiency in La_1−xMn_1−xO₃, the ferromagnetic transition temperature was found to follow a bell shape with respect to x exhibiting a maximum of ∼250 K about x≈0.1. For moderately oxygenated samples large magnetoresistance effect was evidenced.     

Preparation, structure and oxide ion conductivity in Ce6−xYxMoO15−δ (x=0.1-1.4) solid solutions

The Ce_6−xY_xMoO_15−δ solid solution with fluorite-related structure have been characterized by differential thermal analysis/thermogravimetry (DTA/TG), X-ray diffraction (XRD), IR, Raman, scanning electric microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) methods. The electric conductivity of samples is investigated by Ac impedance spectroscopy. An essentially pure oxide-ion conductivity of the oxygen-deficiency was observed in pure argon, oxygen and air. The highest oxygen-ion conductivity was found in Ce_5.5Y_0.5MoO_15−δ ranging from 5.9×10⁻⁵ (S cm⁻¹) at 300 °C to 1.3×10⁻² (S cm⁻¹) at 650 °C, respectively. The oxide-ion conductivities remained stable over 80 h-long test at 800 °C. These properties suggested that significant oxide-ionic conductivity exists in these materials at moderately elevated temperatures.     

Increase of Tc in the 1:2:3 superconductors YBCO and (CaxLa1−x)(LauBa1−u)2Cu3Oy after slow cooling or low temperature annealing

The well known phenomenon of the increase of T_c of YBCO after slow cooling or low temperature annealing without change of the oxygen content, was found also for the YBCO like tetragonal superconductors of (Ca_xLa_1−x)(La_uBa_1−u)₂Cu₃O_y (this compound has been previously denoted as CLBLCO, CLBCO or CaLaBaCuO). It has been observed at 150 and 100 °C for oxygen underdoped, optimally- and overdoped ceramics. The products retain their tetragonal unit cells. The possible reasons of this phenomenon are discussed.     

Luminescent properties of HTP AgGd1−xW2O8:Eux and AgGd1−x(W1−yMoy)2O8:Eux phosphor for white LED

Intense red phosphors, AgGd_1−xEu_x(W_1−yMo_y)₂O₈ (x=0.0-1.0, y=0.0-1.0), have been synthesized through traditional solid-state reaction and characterized by X-ray diffraction (XRD) and photoluminescence (PL). XRD results reveal that AgGd_1−xEu_xW₂O₈ synthesized at 1000 °C has a tetragonal crystal structure, which is named as high temperature phase (HTP) AgGdW₂O₈. All phosphors compositions with Eu³⁺ show red and green emission on excitation either in the charge-transfer or Eu³⁺ levels. Analysis of the emission spectra with different Eu³⁺ concentrations reveal that the optimum dopant concentration for Eu³⁺ is x=0.6 in the HTP AgGd_1−xEu_xW₂O₈ (x=0.0-1.0). Studies on the AgGd_0.4Eu_0.6(W_1−yMo_y)₂O₈ (y=0.0-1.0) and AgGd_1−xEu_x(W_0.7Mo_0.3)₂O₈ (x=0.0-1.0) show that the emission intensity is maximum for compositions with y=0.3 and x=0.5, respectively, and a decrease in emission intensity is observed for higher y or x values. The Mo⁶⁺ and Eu³⁺ co-doped AgGd(WO₄)₂ phosphors show higher emission intensity in comparison with the singly Eu³⁺-doped AgGd(WO₄)₂ in UV region. The intense emission of the tungstate/molybdate phosphors under 394 and 465 nm excitations, respectively, suggests that these materials are promising candidates as red-emitting phosphors for near-UV/blue GaN-based white LED for white light generation.     

Effect of fabrication parameters on the electrical conductivity of YxSr1−xTiO3 for anode materials

Yttrium-doped strontium titanate (Y_xSr_1−xTiO₃), as probable anode material for SOFC, was prepared by solid-state reaction. The solubility of yttrium in SrTiO₃ at different temperatures was examined and the electrical conductivities of Y_xSr_1−xTiO₃ were measured from 500 to 1000 °C. The effects of doping amount, fabrication atmosphere, and sintering temperature on the electrical conductivity of Y_xSr_1−xTiO₃ were investigated. Y_xSr_1−xTiO₃ with x=0.08 was found to give the maximum electrical conductivity, 71 S/cm at 800 °C in pure hydrogen. Reducing atmospheres and appropriate sintering temperatures play a positive role in improving the electrical conductivity.     

Electrical and electrochemical properties of molten salt-synthesized Li4Ti5−xSnxO12 (x=0.0, 0.05 and 0.1) as anodes for Li-ion batteries

Submicron-sized polyhedral Li₄Ti_5−xSn_xO₁₂ (x=0.0, 0.05, and 0.1) materials were successfully prepared by a single-step molten salt method. The structural, morphological, transport and electrochemical properties of the Li₄Ti_5−xSn_xO₁₂ were studied. X-ray diffraction patterns showed the formation of a cubic structure with a lattice constant of 8.31 Å, and the addition of dopants follows Vegard's law. Furthermore, FT-IR spectra revealed symmetric stretching vibrations of octahedral groups of MO₆ lattice in Li₄Ti₅O₁₂. The formation of polyhedral submicron Li₄Ti_5−xSn_xO₁₂ particles was inferred from FE-SEM images, and a particle size reduction was observed for Sn-doped Li₄Ti₅O₁₂. The chemical composition of Ti, O and Sn was verified by EDAX. The DC electrical conductivity was found to increase with increasing temperature, and a maximum conductivity of 8.96×10⁻⁶ S cm⁻¹ was observed at 200 °C for Li₄Ti₅O₁₂. The galvanostatic charge–discharge behavior indicates that the Sn-doped Li₄Ti₅O₁₂ could be used as an anode for Li-ion batteries due to its enhanced electrochemical properties.     

Preparation and multi-properties of insulated single-phase BiFeO3 ceramics

Six types of BiFeO₃ ceramic samples, with subtle differences in synthesis conditions, were prepared. The comparison of their phases, electrical resistivity, and porosity revealed that the use of Bi₂O₃ and Fe₂O₃ powders of <1 μm size and a rapid liquid-phase sintering process of 855 °C for 5 min at 100 °C/s is beneficial to synthesize poreless single-phase BiFeO₃ samples with high electrical resistivity of ∼5×10¹² Ω cm. Deoxygenated Bi_xFe_yO_{1.5x+1.5y−δ} (x≠y, δ≥0) impurities were identified and found to be the main cause of low electrical resistivity and high porosity in the multi-phase samples. Large saturation polarization of 16.6 μC/cm² and low leakage current density of 30 mA/m², both at a high electric field of 145 kV/cm, were measured in the optimized single-phase samples at room temperature besides a large piezoelectric d₃₃ coefficient of 27 pC/N and an obvious canted antiferromagnetic behavior.     

Control of luminescence and conductivity of delafossite-type CuYO2 by substitution of rare earth cation (Eu, Tb) and/or Ca cation for Y cation

Delafossite-type oxides of CuTb_yY_1−yO₂, CuEu_yY_1−yO₂, CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ have been prepared by solid state reactions. The lattice-parameter dependence on the composition implies substitution of the Tb³⁺, Eu³⁺ and Ca²⁺ cations for the Y³⁺ site. Noticeable sharp emission lines due to the f-f transitions (⁵D₄→⁷F_J, J=3-6) of Tb³⁺ or due to the f-f transitions (⁵D₀→⁷F_J, J=0-4) of Eu³⁺ are observed at room temperature. Electrical conductivities of CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ are larger than those of CuTb_yY_1−yO₂ and CuEu_yY_1−yO₂, indicating the increase of the hole concentration caused by the substitution of Ca²⁺ for the Y³⁺ site. These results indicate the controllability of the luminescence and conductivity in CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ delafossite-type oxides by simultaneous substitution of the rare earth Tb³⁺ or Eu³⁺ cation and the Ca²⁺ cation for the Y³⁺ site.     

Effect of Bi2O3 on EPR, optical transmission and DC conductivity of vanadyl doped alkali bismuth borate glasses

Glasses with composition xBi₂O₃·(30−x)M₂O·70B₂O₃ (M=Li, Na) containing 2 mol% V₂O₅ have been prepared over the range 0≤x≤15 (x is in mol%). The electron paramagnetic resonance spectra of VO²⁺ of these glasses have been recorded in the X-band (≈9.3 GHz) at room temperature (RT≈300 K). Spin Hamiltonian parameters, g_∥, g_⊥, A_∥, A_⊥, dipolar hyperfine coupling parameter, P, and Fermi contact interaction parameter, K, have been calculated. The molecular orbital coefficients, α² and γ², have been calculated by recording the optical transmission spectra. In xBi₂O₃·(30−x)Li₂O·70B₂O₃ glasses there is decrease in the tetragonality of the V⁴⁺O₆ complex for x up to 6 mol% whereas for x≥6 mol%, tetragonality increases. In xBi₂O₃·(30−x)Na₂O·70B₂O₃ glasses there is increase in the tetragonality of the V⁴⁺O₆ complex with increasing x. The 3d_xy orbit expands with increase in Bi₂O₃:M₂O ratio. Values of the theoretical optical basicity, Λ_th, have also been reported. The DC conductivity increases with increase in temperature. The order of conductivity is 10⁻⁵ ohm⁻¹ m⁻¹ at low temperature and 10⁻³ ohm⁻¹ m⁻¹ at high temperature. The DC conductivity decreases and the activation energy increases with increase in Bi₂O₃:M₂O ratio.     

Phase transition, structural and electrical properties of Pb(Zn1/3Nb2/3)O3-doped Pb(Ni1/3Nb2/3)O3-PbTiO3 ceramics prepared by solid-state reaction method

Phase pure perovskite (1−x−y)Pb(Ni_1/3Nb_2/3)O₃-xPb(Zn_1/3Nb_2/3)O₃-yPbTiO₃ (PNN-PZN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via a B-site oxide mixing route. The PNN-PZN-PT ceramics sintered at the optimized condition of 1185 °C for 2 h exhibit high relative density and rather homogenous microstructure. With the increase of PbTiO₃ (PT) content, crystal structure and electrical properties of the synthesized PNN-PZN-PT ceramics exhibit successive phase transformation. A morphotropic phase boundary (MPB) is supposed to form in (0.9−x)PNN-0.1PZN-xPT at a region of x=32-36 mol% confirmed by X-ray diffraction (XRD) measurement and dielectric measurement. The MPB composition can be pictured as providing a “bridge” connecting rhombohedral ferroelectric (FE) phase and tetragonal one since crystal structure of the MPB composition is similar to both the rhombohedral and tetragonal lattices. Dielectric response of the sintered PNN-PZN-PT ceramics also exhibits successive phase-transition character. 0.64PNN-0.1PZN-0.26PT exhibits broad, diffused and frequency dependent dielectric peaks indicating a character of diffused FE-paraelectric (PE) phase transition of relaxor ferroelectrics and 0.40PNN-0.1PZN-0.50PT exhibits narrow, sharp and frequency independent dielectric peaks indicating a character of first-order FE-PE phase transition of normal ferroelectrics. The FE-PE phase transition of 0.56PNN-0.1PZN-0.34PT is nearly first-order with some diffused character, which also exhibits the largest value of piezoelectric constant d₃₃ of 462pC/N.     

Enhanced ferroelectric properties of (Pb0.90La0.10)Ti0.975O3 multilayered thin films prepared by RF magnetron sputtering

The (Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PLT/PT), PbTiO₃/(Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PT/PLT/PT) multilayered thin films with a PbO_x buffer layer were in situ deposited by RF magnetron sputtering at the substrate temperature of 600 °C. With this method, highly (1 0 0)-oriented PLT/PT and PT/PLT/PT multilayered thin films were obtained. The PbO_x buffer layer leads to the (1 0 0) orientation of the films. The dielectric, ferroelectric and pyroelectric properties of the PLT multilayered thin films were investigated. It is found that highly (1 0 0)-oriented PT/PLT/PT multilayered thin films possess higher remnant polarization 2P_r (44.1 μC/cm²) and better pyroelectric coefficient at room temperature p (p = 2.425 × 10⁻⁸ C/cm² K) than these of PLT and PLT/PT thin films. These results indicate that the design of the PT/PLT/PT multilayered thin films with a PbO_x buffer layer should be an effective way to enhance the dielectric, ferroelectric and pyroelectric properties. The mechanism of the enhanced ferroelectric properties was also discussed.     

Synthesis, physical and photo electrochemical characterization of La-doped SrSnO3

The transport properties of Sr_0.98La_0.02SnO_3−δ in the system Sr_1−xLa_xSnO_3−δ, after which the pyrochlore La₂Sn₂O₇ appears, were investigated over the temperature range 4.2-300 K. The oxide was found to be n-type semiconductor with concomitant reduction of Sn⁴⁺ into Sn²⁺. The magnetic susceptibility was measured down to 4.2 K and is less than 3×10⁻⁵ emu cgs mol⁻¹ consistent with itinerant electron behavior. The electron is believed to travel in a narrow band of Sn:5s character with an effective mass ∼4 m_o. The highest band gap is 4.32 eV and the optical transition is directly allowed. A further indirect transition occurs at 4.04 eV. The electrical conductivity follows an Arrhenius-type law with a thermal activation of 40 meV and occurs by small polaron hopping between nominal states Sn^4+/2+. The linear increase of thermo-power with temperature yields an electron mobility μ_300 K (2×10⁻⁴ cm² V⁻¹ s⁻¹) thermally activated. The insulating-metal transition seems to be of Anderson type resulting from random positions of lanthanum sites and oxygen vacancies. At low temperatures, the conduction mechanism changes to a variable range hopping with a linear plot Ln ρ⁻¹ vs. T⁻⁴. The photo electrochemical (PEC) measurements confirm the n-type conductivity and give an onset potential of −0.46 V_SCE in KOH (1 M). The Mott-Schottky plot C⁻²-V shows a linear behavior from which the flat band potential V_fb=+0.01 V_SCE at pH 7 and the doping density N_D=1.04×10²¹ cm⁻³ were determined.     

Effect of microstructure on the conductivity of a NASICON-type lithium ion conductor

Sintering temperature is used to control the microstructure of Li_{1 + x + y}Al_xTi_2 − xSi_yP_3 − yO₁₂ (x = 0.3, y = 0.2), a NASICON-type glass-ceramic. Scanning Electron Microscope imaging, X-Ray Diffraction, and Electrochemical Impedance Spectroscopy are employed to show that increase in sintering temperature increases conductivity while generating secondary crystalline phases. Total conductivity is as high as 3.81 × 10⁻⁴ S cm⁻¹ for sintering temperatures above 1000 °C. Crystallization of dielectric phases places the optimal sintering temperature in the 900 °C to 1000 °C range. Thermal analysis of the glass precursor reveals the glass transition, and crystallization temperatures.     

Effect of Mn-site vacancies on the magnetic entropy change and the Curie temperature of La0.67Ca0.33Mn1−xO3 perovskite

Single-phase polycrystalline samples of La_0.67Ca_0.33Mn_1−xO₃ (x=0.00, 0.02, 0.04, 0.06) have been prepared using the sol-gel method. The structure, magnetocaloric properties and the Curie temperature of the samples with different Mn vacancy concentrations have been investigated. The experimental results show that vacancy doping at the Mn-sites has a significant influence on the magnetic properties of La_0.67Ca_0.33Mn_1−xO₃. The Curie temperature decreases monotonically with increasing the Mn-site vacancy concentration x. A remarkable enhancement of the magnetic entropy change has been obtained in the La_0.67Ca_0.33Mn_0.98O₃ sample. The entropy change reaches |ΔS_M|=3.10 J kg⁻¹ K⁻¹ at its Curie temperature (264 K) under an applied magnetic field H=10 kOe, which is almost the same value as that of pure Gd.     

The microwave absorption properties of La0.8Sr0.2Mn1−yFeyO3 nanocrystalline powders in the frequency range 2-18 GHz

La_1−xSr_xMn_1−yFe_yO₃ nanocrystalline powders were prepared by the sol-gel method as a microwave absorption material. The reflectance, the dielectric loss tan δ_e and the magnetic loss tan δ_m of the samples were calculated according to the data of electromagnetism parameters measured by a microwave vector network analyzer in the frequency range 2-18 GHz. The dielectric loss tan δ_e and the magnetic loss tan δ_m had a step-change at a certain frequency so that the superiority of dielectric loss change into the superiority of magnetic loss, which indicated that anti-ferromagnetic clusters in the material change into ferromagnetic clusters by absorbing quantum of microwave electromagnetic field when the frequency of incident microwave reaches a certain value. The effective absorption bandwidth higher than 10 dB reached 6.2 GHz. As a result, the La_0.8Sr_0.2Mn_1−yFe_yO₃ has shown useful applications as a microwave absorption material.     

Dielectric properties of lanthanum-doped CaCu3Ti4O12 synthesized by semi-wet route

Effect of La³⁺ doping at Ca²⁺ site in CaCu₃Ti₄O₁₂ has been examined. Compositions with x=0.10, 0.20 and 0.30 were synthesized in the system Ca_(1−3x/2)La_xCu₃Ti₄O₁₂ by semi-wet method. Powder X-ray diffraction confirmed the formation of monophasic compounds. The structure remains cubic similar to CaCu₃Ti₄O₁₂. Lattice parameter increases slightly with increasing La³⁺ concentration. Microstructure has been studied using scanning electron microscopy (SEM). Average grain size is in the range 2-4 μm for various compositions. Energy-dispersive spectrometer (EDS) studies confirm the stoichiometry of the synthesized materials. Dielectric constant, dielectric loss and conductivity of the samples decrease with increasing lanthanum concentrations.     

Ionic to electronic dominant conductivity in Al2(WO4)3 at high pressure and high temperature

Electrical conduction and crystal structure of Al₂(WO₄)₃ at 400 °C have been studied as a function of pressure up to 5.5 GPa using impedance methods and synchrotron radiation X-ray diffraction, respectively. AC impedance spectroscopy and DC polarization measurements reveal an ionic to electronic dominant transition in electrical conductivity at a pressure as low as 0.9 GPa. Conductivity increases with pressure and reaches a maximum at 4.0 GPa, where the conductivity value is 5 orders of magnitude greater than the 1 atm value. Upon decompression, the conductivity retains the maximum value until the sample is cooled at 0.5 GPa. The high pressure-temperature X-ray diffraction results show that the lattice parameters decrease as pressure increases and the crystal structure undergoes an orthorhombic to tetragonal-like transformation at a pressure ∼3.0 GPa. The change of conduction mechanism from ionic to electronic may be explained by means of pressure-induced valence change of W⁶⁺→W⁵⁺, which results in electron transfer between W⁵⁺-W⁶⁺ sites at high pressure.