Preparation of Fe2O3/SrTiO3 composite powders and their photocatalytic properties

Fe₂O₃/SrTiO₃ composite powders have been prepared and their photocatalytic activities were investigated by photooxidizing methanol. These powders were characterized by ultraviolet (UV)-visible diffuse reflectance spectra, scanning electron microscope (SEM) and X-ray diffraction (XRD). The results showed that the Fe₂O₃/SrTiO₃ composite powders with optimum proportion exhibited higher photocatalytic activity than pure SrTiO₃, Fe₂O₃ and TiO₂ (P25) under visible light (λ>440 nm) irradiation. The SEM image of the composite powders showed that SrTiO₃ and Fe₂O₃ particles contacted well. Further research revealed that the calcination temperature is an important factor in the preparation of the composite powder with relatively high photocatalytic ability.     

Preparation, characterization and photocatalytic activity of polycrystalline Bi2O3/SrTiO3 composite powders

Bi₂O₃/SrTiO₃ composite powders have been prepared and their photocatalytic activities were investigated by photooxidation of methanol. These powders were characterized by UV-Visible diffuse reflectance spectra, SEM and X-ray diffraction (XRD). The results revealed that all the Bi₂O₃/SrTiO₃ composite powders exhibited higher photocatalytic activity than pure SrTiO₃, Bi₂O₃ and TiO₂ (P25) under visible light irradiation (λ>440 nm). The effects of the Bi₂O₃ contents on the photocatalytic activities of the composite powders were examined, the photocatalytic activities increased with the content of Bi₂O₃ increasing to a maximum of 83% and then decreased under visible light irradiation. The effects of the calcination temperatures on the photocatalytic activities of the composite powders were also investigated.     

Preparation and visible light photocatalytic performance of methylene blue intercalated K4Nb6O17

K₄Nb₆O₁₇ was prepared by hydrothermal treatment of Nb₂O₅ in KOH solution at 180 °C, and then Methylene blue (MB) intercalated K₄Nb₆O₁₇ (K₄Nb₆O₁₇-MB) was prepared by one-pot reaction in which n-propylamine (PA) was used as an intercalation compound. The MB intercalated structure of K₄Nb₆O₁₇-MB was characterized by HRTEM and XRD measurements. K₄Nb₆O₁₇-MB shows good absorption in the visible region and is thermally stable up to 328 °C. By extending the hydrothermal time and selecting the K₄Nb₆O₁₇ with high crystallinity, the K₄Nb₆O₁₇-MB prepared by one-pot reaction showed higher visible light (λ>550 nm) photocatalytic activity than that prepared by traditional two-step electrostatic self-assembly deposition (ESD) method for the degradation of methyl orange (MO).     

Characteristics of spherical-shaped Li4Ti5O12 anode powders prepared by spray pyrolysis

Spherical-shaped Li₄Ti₅O₁₂ anode powders with a mean size of 1.5 μm were prepared by spray pyrolysis. The precursor powders obtained by spray pyrolysis had no peaks of crystal structure of Li₄Ti₅O₁₂. The powders post-treated at temperatures of 800 and 900 °C had the single phase of spinel Li₄Ti₅O₁₂. The powders post-treated at a temperature of 1000 °C had main peaks of the Li₄Ti₅O₁₂ phase and small impurity peaks of Li₂Ti₃O₇. The spherical shape of the precursor powders was maintained after post-treatment at temperatures below 800 °C. The Brunauer-Emmett-Teller (BET) surface areas of the Li₄Ti₅O₁₂ anode powders post-treated at temperatures of 700, 800 and 900 °C were 4.9, 1.6 and 1.5 m²/g, respectively. The initial discharge capacities of Li₄Ti₅O₁₂ powders were changed from 108 to 175 mAh/g when the post-treatment temperatures were changed from 700 to 1000 °C. The maximum initial discharge capacity of the Li₄Ti₅O₁₂ powders was obtained at a post-treatment temperature of 800 °C, which had good cycle properties below current densities of 0.7 C.     

Surface photoelectric and photodegradation activities of AgNbO3 synthesized by solvothermal method

Silver niobate (AgNbO₃) with different morphologies is obtained by annealing the precursors prepared at different temperatures by solvothermal method at 800 °C. Scanning electron microscope images of the samples show the formation process of the morphologies. The weakest photovoltaic and the highest photocatalytic properties of the sample obtained from the precursors prepared at 190 °C are possibly caused by the synergetic effects between several kinds of particles, and between AgNbO₃ and Nb₂O₅. Both the temperature and the amount of Nb₂O₅ are crucial for the morphologies, the photoelectric and photocatalytic properties of the samples.     

High-temperature crystal structure and electronic properties of cesium niobate Cs2Nb4O11

The antiferroelectric material Cs₂Nb₄O₁₁ transforms at 165 °C from a low-temperature, antiferroelectric phase in space group Pnna to a high-temperature, paraelectric phase in space group Imma; the latter structure has been determined by single-crystal X-ray diffraction. The high-temperature lattice is comprised of niobium-centered tetrahedra and octahedra connected through shared vertices and edges; cesium atoms occupy channels afforded by the three-dimensional polyhedral network. Calculated band structures for both phases predict a bandgap of 3.1-3.2 eV, which is similar to that found experimentally through photoluminescence. The calculated band structure is also conducive to its observed photocatalytic properties.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Immiscibility in the NiFe2O4-NiCr2O4 spinel binary

The solid solution behavior of the Ni(Fe_1−nCr_n)₂O₄ spinel binary is investigated in the temperature range 400-1200 °C. Non-ideal solution behavior, as exhibited by non-linear changes in lattice parameter with changes in n, is observed in a series of single-phase solids air-cooled from 1200 °C. Air-annealing for 1 year at 600 °C resulted in partial phase separation in a spinel binary having n=0.5. Spinel crystals grown from NiO, Fe₂O₃ and Cr₂O₃ reactants, mixed to give NiCrFeO₄, by Ostwald ripening in a molten salt solvent, exhibited single-phase stability down to about 750 °C (the estimated consolute solution temperature, T_cs). A solvus exists below T_cs. The solvus becomes increasingly asymmetric at lower temperatures and extrapolates to n values of 0.2 and 0.7 at 300 °C. The extrapolated solvus is shown to be consistent with that predicted using a primitive regular solution model in which free energies of mixing are determined entirely from changes in configurational entropy at room temperature.     

Sol-gel preparation and characterization of CoFe2O4-SiO2 nanocomposites

Magnetic nanocomposites formed by cobalt ferrite particles dispersed in a silica matrix were prepared by a sol-gel process. The effects of the thermal treatment temperature and the salt concentration on the structural and magnetic properties of the composites were investigated. By controlling these parameters, CoFe₂O₄/SiO₂ nanocomposites with different crystallite size and magnetic properties were obtained. By increasing the annealing temperature and salt concentration, composites with a progressive increase in the coercive field and of the density of magnetization were produced. In particular, a nanocomposite, with a Fe/Si molar concentration of 21%, obtained by drying the gel at 150 °C and further annealing at 800 °C, has a coercivity of 2000 Oe, which is more than twice higher than the coercivity of bulk cobalt ferrite.     

Electrical properties of SrBi2(Nb0.5Ta0.5)2O9 ceramics

Aurivillius SrBi₂(Nb_0.5Ta_0.5)₂O₉ (SBNT 50/50) ceramics were prepared using the conventional solid-state reaction method. Scanning electron microscopy was applied to investigate the grain structure. The XRD studies revealed an orthorhombic structure in the SBNT 50/50 with lattice parameters a=5.522 Å, b=5.511 Å and c=25.114 Å. The dielectric properties were determined by impedance spectroscopy measurements. A strong low frequency dielectric dispersion was found to exist in this material. Its occurrence was ascribed to the presence of ionized space charge carriers such as oxygen vacancies. The dielectric relaxation was defined on the basis of an equivalent circuit. The temperature dependence of various electrical properties was determined and discussed. The thermal activation energy for the grain electric conductivity was lower in the high temperature region (T>303.6 °C, E_a−ht=0.47 eV) and higher in the low temperature region (T<303.6 °C, E_a−lt=1.18 eV).     

Photoluminescence of Y2O3:Eu thin film phosphors by sol-gel deposition and rapid thermal annealing

Y₂O₃:Eu³⁺ phosphor films have been developed by using the sol-gel process. Comprehensive characterization methods such as Photoluminescent (PL) spectroscopy, X-ray diffraction (XRD) and Fourier Transform Infrared (FTIR) spectroscopy were used to characterize the Y₂O₃:Eu³⁺ phosphor films. In this experiment, the XRD profiles show that the Y₂O₃:Eu³⁺ phosphor films crystallization temperature and optimum annealing temperature occur at about 650 and 750 °C, respectively. The optimum dopant concentration is 12 mol% Eu³⁺ and the critical transfer distance (R_c) among Eu³⁺ ions is calculated to be about 0.84 nm. Vacuum environment is more efficient than oxygen and nitrogen to eliminate the OH content and hence yields higher luminescent phosphor films. The PL emission intensity of Y₂O₃:Eu³⁺ phosphor films is also dependent on the annealing time. It was found that the H₂O impurities were effectively eliminated after annealing time of 25 s at 750 °C in vacuum environment. From the experiment results, the schematic energy band diagram of Y₂O₃:Eu³⁺ phosphor films is constructed.     

Synthesis of In-doped Ga2O3 zigzag-shaped nanowires and optical properties

In-doped Ga₂O₃ zigzag-shaped nanowires and undoped Ga₂O₃ nanowires have been synthesized on Si substrate by thermal evaporation of mixed powders of Ga, In₂O₃ and graphite at 1000 °C without using any catalyst via a vapor-solid growth mechanism. The morphologies and microstructures of the products were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and photoluminescence spectroscopy (PL). The nanowires range from 100 nm to several hundreds of nanometers in diameter and several tens of micrometers in length. A broad emission band from 400 to 700 nm is obtained in the PL spectrum of these nanowires at room temperature. There are two blue-emission peaks centering at 450 and 500 nm, which originate from the oxygen vacancies, gallium vacancies and gallium-oxygen vacancy pairs.     

Microstructure and interfacial properties of HfO2-Al2O3 nanolaminate films

High-k HfO₂-Al₂O₃ composite gate dielectric thin films on Si(1 0 0) have been deposited by means of magnetron sputtering. The microstructure and interfacial characteristics of the HfO₂-Al₂O₃ films have been investigated by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and spectroscopic ellipsometry (SE). Analysis by XRD has confirmed that an amorphous structure of the HfO₂-Al₂O₃ composite films is maintained up to an annealing temperature of 800 °C, which is much higher than that of pure HfO₂ thin films. FTIR characterization indicates that the growth of the interfacial SiO₂ layer is effectively suppressed when the annealing temperature is as low as 800 °C, which is also confirmed by spectroscopy ellipsometry measurement. These results clearly show that the crystallization temperature of the nanolaminate HfO₂-Al₂O₃ composite films has been increased compared to pure HfO₂ films. Al₂O₃ as a passivation barrier for HfO₂ high-k dielectrics prevents oxygen diffusion and the interfacial layer growth effectively.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Synthesis and luminescence properties of needle-like SrAl2O4:Eu, Dy phosphor via a hydrothermal co-precipitation method

Needle-like SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors had been prepared by calcining the precursors obtained from hydrothermal process at the temperature of 1100 °C in a weak reductive atmosphere of active carbon. The crystal structure, morphology and optical properties of the composites were characterized. X-ray diffraction (XRD) patterns illustrated that the single-phase SrAl₂O₄ was formed at 1100 °C, which is much lower than that prepared by the traditional method. The transmission electron microscope (TEM) observation revealed the precursors and the resulted SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors had well-dispersed distribution and needle-like morphology with an average diameter about 150 nm at the center and the length up to 1 μm. After irradiation by ultraviolet radiation with 350 nm for 5 min, the phosphors emit green color long-lasting phosphorescence corresponding to the typical emission of Eu²⁺ ion, both the PL spectra and luminance decay revealed that the phosphors had efficient luminescent and long lasting properties.     

Structural and impedance properties of Ca3Nb2O8 ceramics

Polycrystalline sample of Ca₃Nb₂O₈ was prepared by a high-temperature solid-state reaction technique. X-ray diffraction (XRD) analysis confirms the formation of single-phase compound of hexagonal (rhombohedral) crystal structure at room temperature. Scanning electron micrograph of the material showed uniform grain distribution on the surface of the sample. Detailed studies of dielectric properties of the compound, studied in a wide frequency range (10²-10⁶ Hz) at different temperatures (25-500 °C), exhibit a dielectric anomaly suggesting phase transition of ferroelectric-paraelectric and structural type at 300 °C. Electrical properties of the material were analyzed using a complex impedance technique. The Nyquists plot showed the presence of bulk effect in the material in the studied temperature range. Studies of electrical conductivity over a wide temperature range suggest that the compound has negative temperature coefficient of resistance behavior.     

Facile synthesis of Nb2O5 nanorod array films and their electrochemical properties

Nb₂O₅ nanorod array films were synthesized by a facile hydrothermal process using niobium metal foil and NH₄F as precursors. The Nb₂O₅ nanorods stand on the niobium metal foil substrate and are less than 100 nm in diameter and about 1 μm in length. X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM) characterizations indicate that these nanorods have orthorhombic structure and grew longitudinally along 〈0 0 1〉 direction. The nanorod growth mechanism was discussed. Thermal annealing at a temperature below 500 °C did not change the microstructure of nanorods but improve the crystallinity. The Nb₂O₅ nanorod array films have been tested as cathode material for lithium battery, which showed a good specific capacity up to 380 mAh g⁻¹ even after 50 charge/discharge cycles.     

Nanoparticles of the giant dielectric material, CaCu3Ti4O12 from a precursor route

A method of preparing the nanoparticles of CaCu₃Ti₄O₁₂ (CCTO) with the crystallite size varying from 30 to 200 nm is optimized at a temperature as low as 680 °C from the exothermic thermal decomposition of an oxalate precursor, CaCu₃(TiO)₄(C₂O₄)₈·9H₂O. The phase singularity of the complex oxalate precursor is confirmed by the wet chemical analyses, X-ray diffraction, FT-IR and TGA/DTA analyses. The UV-vis reflectance and ESR spectra of CCTO powders indicate that the Cu(II) coordination changes from distorted octahedra to nearly flattened tetrahedra (squashed) to square-planar geometry with increasing annealing temperature. The HRTEM images have revealed that the evolution of the microstructure in nanoscale is related to the change in Cu(II) coordination around the surface regions for the chemically prepared powder specimens. The nearly flattened tetrahedral geometry prevails for CuO₄ in the near surface regions of the particles, whereas square-planar CuO₄ groups are dominant in the interior regions of the nanoparticles. The powders derived from the oxalate precursor have excellent sinterability, resulting in high-density ceramics which exhibited giant dielectric constants upto 40,000 (1 kHz) at 25 °C, accompanied by low dielectric loss <0.07.     

Study of phase transition in ZrO2 doped with Pb3O4

Electrical conductivity of ZrO₂ doped with Pb₃O₄ has been measured at different temperatures for different molar ratios (x=0, 0.01, 0.02, 0.03, 0.04, 0.05 and 0.06). The conductivity increases due to migration of vacancies, created by doping. The conductivity increases with increase in temperature till 180 °C and thereby decreases due to collapse of the fluorite framework. A second rise in conductivity at higher temperatures beyond 500-618 °C is due to phase transition of ZrO₂. DTA and X-ray powder diffraction were carried out for confirming doping effect and transition in ZrO₂.The addition of Pb₃O₄ to ZrO₂ shifted the phase transition of ZrO₂ due to the interaction between Pb₃O₄ and ZrO₂.     

Characterization of CuAlO2 thin film prepared by rapid thermal annealing of an Al2O3/Cu2O/sapphire structure

CuAlO₂ thin film was successfully prepared by rapid thermal annealing of an Al₂O₃/Cu₂O/sapphire structure in air above 1000 °C. The film was mostly with single crystalline structure as verified by X-ray diffraction methods. We found that crystal quality and electrical conductivity of the films were affected by the cooling rate after annealing. The highest conductivity obtained in this work was 0.57 S/cm. Optical gap of this film was determined to be 3.75 eV.