磁控溅射制备本征ZnO/Ag/ZnO透明导电薄膜的性质研究

室温下采用射频磁控溅射氧化锌（ZnO）粉末靶、银（Ag）靶,在玻璃衬底上制备ZnO/Ag/ZnO透明导电薄膜。首先,ZnO厚度为30 nm时,改变Ag厚度制备3层透明导电薄膜,研究Ag层厚度及膜层间配比对光电性能的影响;其次,按ZnO∶Ag厚度比为30∶11比例制备不同厚度的3层透明导电薄膜,研究多层厚度对薄膜光电性能的影响。结果表明：Ag厚度为8 nm及11 nm的ZnO/Ag/ZnO表面相对平整,结晶程度较好,在可见光范围内最高透过率达到90%及86%,并且方块电阻为6 Ω/□及3.20 Ω/□,具有优良的光电性;当按配比制备ZnO/Ag/ZnO 3层膜时,增加ZnO厚度对Ag层的增透作用反而减弱,同时增加Ag层厚度也会降低3层薄膜的整体光学性。     

ZnO/Ag/ZnO multilayer films for the application of a very low resistance transparent electrode

Transparent conductive ZnO/Ag/ZnO multilayer electrodes having much lower electrical resistance than the widely used transparent electrodes were prepared by simultaneous RF magnetron sputtering of ZnO and DC magnetron sputtering of Ag. An Ag film with different thickness was used as intermediate metallic layers. The optimum thickness of Ag thin films was determined to be 6 nm for high optical transmittance and good electrical conductivity. With about 20-25 nm thick ZnO films, the multilayer showed high optical transmittance in the visible range of the spectrum and had color neutrality. The electrical and optical properties of the multilayers were changed mainly by Ag film properties. A high quality transparent electrode, having sheet resistance as low as 3 ohm/sq and high transmittance of 90% at 580 nm, was obtained and could be reproduced by controlling the preparation parameter properly. The above property is suitable as transparent electrode for dye sensitized solar cells (DSSC).     

Au层退火温度对ZnO/Au/ZnO多层膜的结构、光学及电学性质的影响

采用金属有机化学气相沉积(MOCVD)技术在蓝宝石衬底上制备出晶体质量较好的透明导电的ZnO/Au/ZnO(ZAZ)多层膜,其中,Au夹层是通过射频磁控溅射的方法获得。通过对Au夹层进行不同温度的退火处理,研究了Au层退火温度对ZAZ多层膜的结构特性、电学性能和光学特性的影响。利用原子力显微镜(AFM)、扫描电子显微镜(SEM)、X射线衍射(XRD)仪、霍尔效应测试和透射谱分析等测试手段对ZAZ多层膜的性质进行了分析。测试结果表明,在200 ℃下对Au夹层进行快速退火处理,多层膜的结构、电学和光学性质达到最优,表面等离子体效应也更明显。其中,XRD(002)衍射峰的半高宽为0.14°,电阻率为2.7×10^-3 Ω·cm,载流子浓度为1.07×10²⁰ cm^-3,可见光区平均透过率为75.3%。     

Highly flexible transparent and conductive ZnS/Ag/ZnS multilayer films prepared by ion beam assisted deposition

ZnS/Ag/ZnS (ZAZ) multilayer films were prepared on polyethene terephthalate (PET) by ion beam assisted deposition at room temperature. The structural, optical and electrical characteristics of ZAZ multilayers dependent on the thickness of silver layer were investigated. The ZAZ multilayers exhibit a low sheet resistance of about 10 Ω/sq., a high transmittance of 92.1%, and the improved resistance stabilities when subjected to bending. When the inserted Ag thickness is over 12 nm, the ZAZ multilayers show good resistance stabilities due to the existence of a ductile Ag metal layer. The results suggest that ZAZ film has better optoelectrical and anti-deflection characteristics than conventional indium tin oxide (ITO) single layer.     

Study on the electrical and optical properties of Ag/Al-doped ZnO coatings deposited by electron beam evaporation

A layer of silver was deposited onto the surface of glass substrates, coated with AZO (Al-doped ZnO), to form Ag/AZO film structures, using e-beam evaporation techniques. The electrical and optical properties of AZO, Ag and Ag/AZO film structures were studied. The deposition of Ag layer on the surface of AZO films resulted in lowering the effective electrical resistivity with a slight reduction of their optical transmittance. Ag (11 nm)/AZO (25 nm) film structure, with an accuracy of ±0.5 nm for the thickness shows a sheet resistance as low as 5.6 ± 0.5 Ω/sq and a transmittance of about 66 ± 2%. A coating consisting of AZO (25 nm)/Ag (11 nm)/AZO (25 nm) trilayer structure, exhibits a resistance of 7.7 ± 0.5 Ω/sq and a high transmittance of 85 ± 2%. The coatings have satisfactory properties of low resistance, high transmittance and highest figure of merit for application in optoelectronics devices including flat displays, thin films transistors and solar cells as transparent conductive electrodes.     

Deposition and characterization of transparent and conductive sprayed ZnO:B thin films

Highly transparent and conductive Boron doped zinc oxide (ZnO:B) thin films were deposited using chemical spray pyrolysis (CSP) technique on glass substrate. The effect of variation of boron doping concentration in reducing solution on film properties was investigated. Low angle X-ray analysis showed that the films were polycrystalline fitting well with a hexagonal wurtzite structure and have preferred orientation in [002] direction. The films with resistivity 2.54×10⁻³ Ω-cm and optical transmittance >90% were obtained at optimized boron doping concentration. The optical band gap of ZnO:B films was found ∼3.27 eV from the optical transmittance spectra for the as-deposited films. Due to their excellent optical and electrical properties, ZnO:B films are promising contender for their potential use as transparent window layer and electrodes in solar cells.     

The influence of Au thickness on the structural,optical and electrical properties of ZnO/Au/ZnO multilayer films

Transparent and conductive ZnO/Au/ZnO (ZAZ) multilayer films were deposited on glass substrates by magnetron sputtering without intentional substrate heating. The thickness of Au interlayer was set at 1, 2 and 3 nm.The observed structural, optical and electrical properties were dependent on the thickness of the Au interlayer. For all of the ZAZ films, the diffraction peaks in the XRD pattern were identified as the (002) and (103) planes of a ZnO films and the (111) plane of an Au interlayer. The ZAZ films with a 2 nm thick Au interlayer showed a higher figure of merit than the other ZAZ films prepared in this study, and they also demonstrated the relatively high work function of 5.13 eV.From these results, we concluded that a ZAZ film with a 2 nm thick Au interlayer is an alternative candidate for use as a transparent electrode in OLEDs and various flat panel displays.     

Characteristic difference between ITO/ZrCu and ITO/Ag bi-layer films as transparent electrodes deposited on PET substrate

The metallic-glass film of ZrCu layer deposited by co-sputtering was utilized as the metallic layer in the bi-layer structure transparent conductive electrode of ITO/ZrCu (IZC) deposited on the PET substrate using magnetron sputtering at room temperature. In addition, the pure Ag metal layer was applied in the same structure of transparent conductive film, ITO/Ag, in comparison with the IZC film. The ZrCu layer could form a continuous and smooth film in thickness lower than 6 nm, compared with the island structure of pure Ag layer of the same thickness. The 30 nm ITO/3 nm ZrCu films could show the optical transmittance of 73% at 550 nm wavelength. The 30 nm ITO/12 nm ZrCu films could show the better sheet resistance of 20 Ω/sq, but it was still worse than that of the ITO/Ag films. It was suggested that an alloy system with lower resistivity and negative mixing heat between atoms might be another way to form a continuous layer in thickness lower than 6 nm for metal film.     

Characteristics of ZnO-Cu-ZnO multilayer films on copper layer properties

ZnO/Cu/ZnO multilayers on glass with different copper layer thickness were prepared by simultaneous RF magnetron sputtering of ZnO and dc magnetron sputtering of Cu. Different optimization procedure were used for good transparent conductive film. Several analytical tools such as spectrophotometer, scanning electron microscope (SEM), four point probes were used to explore the causes of the changes in electrical and optical properties. The sheet resistance of the structure was severely influenced by the deposition condition of both top ZnO and intermediate Cu layer. Effect of substrate temperature and annealing treatment on ZnO and Cu layer was analyzed. A sheet resistance of 10 Ω/sq and transmittance over 85% at 580 nm wavelength was achieved and could be reproduced by controlling the preparation process parameter. The results of an optimization condition of both oxide layers and metallic Cu layers are illustrated.     

Influence of post-annealing on the properties of Sc-doped ZnO transparent conductive films deposited by radio-frequency sputtering

Sc-doped ZnO transparent conductive films are deposited on glass substrates by radio-frequency sputtering. The influence of post-annealing on the structural, morphologic, electrical, and optical properties of the films is investigated by energy dispersion X-ray spectroscopy, X-ray diffraction, Hall measurement, and optical transmission spectroscopy. The experimental results show that these films are polycrystalline with a preferred [0 0 1] orientation. The lowest resistivity of 2.6 × 10⁻⁴ Ω cm is obtained from the film annealed at 500 °C. The average optical transmittance of the films is over 90%. These results suggest that Sc-doped ZnO is a good candidate for fabricating high performance transparent conductive films.     

粉末靶制备的AZO/Ag/AZO透明导电薄膜的光电性能

室温下,采用射频磁控溅射AZO粉末靶和Ag靶在玻璃基底上制备Ag层厚度分别为12 nm和15 nm两组对称结构掺铝氧化锌/银/掺铝氧化锌(AZO/Ag/AZO)透明导电薄膜,研究了Ag层和AZO层厚度对薄膜光电性能的影响。结果表明:3层薄膜的可见光区平均透光率达到了80%,550 nm处的最高透过率达到了88%,方块电阻小于5 Ω/□。Ag层厚度是影响AZO/Ag/AZO薄膜光电性能的主要因素,AZO层的厚度对薄膜光学性能影响较大。     

Deposition of Ni, Ag, and Pt-based Al-doped ZnO double films for the transparent conductive electrodes by RF magnetron sputtering

Ni, Ag, and Pt-based Al-doped ZnO (AZO) films have been deposited as transparent conductivity layers on quartz by RF magnetron sputtering and characterized by X-ray diffraction, Hall measurement, optical transmission spectroscopy, scanning electron microscopy (SEM). The deposition of thicker metal layer in double layers resulted in lowering the effective electrical resistivity with a slight reduction of their optical transmittance. A film consisting of AZO (250 nm)/Ni (2 nm) double structure, exhibits a sheet resistance of 21.0 Ω/sq, a high transmittance of 76.5%, and characterize good adhesion to substrate. These results make the satisfactory for GaN-based light-emitting diodes (LEDs) and solar cells with metal-based AZO double films as current spread layers.     

Influence of buffer layer thickness on the structure and optical properties of ZnO thin films

A series of ZnO thin films were deposited on ZnO buffer layers by DC reactive magnetron sputtering. The buffer layer thickness determination of microstructure and optical properties of ZnO films was investigated by X-ray diffraction (XRD), photoluminescence (PL), optical transmittance and absorption measurements. XRD results revealed that the stress of ZnO thin films varied with the buffer layer thickness. With the increase of buffer layer thickness, the band gap edge shifted toward longer wavelength. The near-band-edge (NBE) emission intensity of ZnO films deposited on ZnO buffer layer also varied with the increase of thickness due to the spatial confinement increasing the Coulomb interaction between electrons and holes. The PL measurement showed that the optimum thickness of the ZnO buffer layer was around 12 nm.     

Transparent conductive ITO/Ag/ITO multilayer electrodes deposited by sputtering at room temperature

ITO/Ag/ITO multilayers have been prepared onto conventional soda lime glass substrates by sputtering at room temperature. The optical and electrical characteristics of single layer and multilayer structures have been investigated as a function of the Ag and ITO film thicknesses. Transmittance and sheet resistance values are found mainly dependent on the Ag film thickness; whereas the wavelength range at which the maximum transmittance is achieved can be changed by adjusting the ITO films thickness. ITO/Ag/ITO electrodes with sheet resistance below 6 Ω/sq have been obtained for Ag film thickness above 10 nm and ITO layers thickness in the 30-50 nm range. These multilayers also show high transmittance in the visible spectral region, above 90% by discounting the glass substrate, with a maximum that is located at higher wavelengths for thicker ITO.     

Design and fabrication of nanometric ZnS/Ag/MoO3 transparent conductive electrode and investigating the effect of annealing process on its characteristics

In this paper, a ZnS/Ag/MoO₃ (ZAM) nano-multilayer structure is designed theoretically and optimum thicknesses of each layer are calculated. ZnS/Ag/MoO₃ multilayer films with optimized thicknesses have also been fabricated on glass substrates by thermal evaporation method at room temperature. The structural, electrical and optical properties of ZnS/Ag/MoO₃ multilayer are investigated with respect to the variation of annealing temperature. X-ray diffraction patterns show that increase in annealing temperature increases the crystallinity of the structures. High-quality multilayer films with the sheet resistance of 4.5 Ω/sq and the maximum optical transmittance of 85% at 100 °C annealing temperature are obtained. The allowed direct band gap for annealing at different temperatures is estimated to be in the range of 3.37–3.79 eV. The performance of the ZAM multilayer films are evaluated using a predefined figure of merit. These multilayer films can be used as transparent conductive electrodes in optoelectronic devices such as solar cells and organic light emitting diodes.     

Structural and optical properties of sputtered ZnO thin films

Zinc oxide (ZnO) and aluminium-doped zinc oxide (ZnO:Al) thin films were prepared by RF diode sputtering at varying deposition conditions. The effects of negative bias voltage and RF power on structural and optical properties were investigated. X-ray diffraction measurements (XRD) confirmed that both un-doped and Al-doped ZnO films are polycrystalline and have hexagonal wurtzite structure. The preferential 〈0 0 1〉 orientation and surface roughness evaluated by AFM measurements showed dependence on applied bias voltage and RF power. The sputtered ZnO and ZnO:Al films had high optical transmittance (>90%) in the wavelength range of 400-800 nm, which was not influenced by bias voltage and RF power. ZnO:Al were conductive and highly transparent. Optical band gap of un-doped and Al-doped ZnO thin films depended on negative bias and RF power and in both cases showed tendency to narrowing.     

Highly flexible,transparent, conductive and antibacterial films made of spin-coated silver nanowires and a protective ZnO layer

We prepared highly flexible, transparent, conductive and antibacterial film by spin coating a silver nanowire suspension on a poly (ethylene terephthalate) (PET) substrate. The ZnO layer covered the conductive silver nanowire (AgNW) network to protect the metal nanowires from oxidization and enhance both wire-to-wire adhesion and wire-to-substrate adhesion. It is found that the number of AgNW coatings correlates with both the sheet resistance (R_s) and the transmittance of the AgNW/ZnO composite films. An excellent 92% optical transmittance in the visible range and a surface sheet resistance of only 9 Ω sq⁻¹ has been achieved, respectively. Even after bending 1000 times (5 mm bending radius), we found no significant change in the sheet resistance or optical transmittance. The real-time sheet resistance measured as a function of bending radius also remains stable even at the smallest measured bending radius (1 mm). The AgNW/ZnO composite films also show antibacterial effects which could be useful for the fabrication of wearable electronic devices.     

Fabrication and characterization of Ag intermediate transparent and conducting TiON/Ag/TiON multilayer films

Silver (Ag) intermediate transparent and conducting TiON/Ag/TiON (TAgT) films were deposited by RF and DC magnetron sputtering on glass substrates. Changes in the optoelectrical properties of the films were investigated as a function of Ag thickness. The thickness of the Ag film varied from 5 to 20 nm.In XRD patterns, the TAgT films showed characteristic diffraction peaks for Ag (111), (200), (220), and (311) planes, while peaks for TiON were not observed. Thus, it was concluded that the Ag interlayer did not affect the crystalline structures of the upper TiON films. However, electrical resistivity was dependent on the thickness of the Ag interlayer. For TiON 50/Ag 20/TiON 30 nm films, electrical resistivity decreased to as low as 3.3 × 10^− 4 Ωcm. The optical transmittance was also influenced by the Ag interlayer. As the Ag thickness increased, the optical transmittance decreased to as low as 45% for TiON 50/Ag 20/TiON 30 nm films. From observed figure of merit and work function, it is concluded that a TAgT film with a 5 nm-thick Ag interlayer is a good candidate for use as a transparent electrode in OLEDs and flat panel displays.     

Transparent conductive and near-infrared reflective Cu-based Al-doped ZnO multilayer films grown by magnetron sputtering at room temperature

Cu-based Al-doped ZnO multilayer films were deposited on glass substrates by DC magnetron sputtering at room temperature. Three kinds of multilayer structures (AZO/Cu, AZO/Cu/AZO, and Cu/AZO) were designed for comparison, and the effects of the Cu layer thickness on photoelectrical properties of the multilayer films were investigated. The results revealed that the transparent-conductive property and near-infrared reflectance of the films are closely correlated with the Cu layer thickness, and among the three structures, AZO/Cu bi-layer films exhibited preferable photoelectrical properties. The AZO/Cu bi-layer film with a Cu layer thickness of 7 nm displayed the highest figure of merit of 4.82 × 10⁻³ Ω⁻¹, with a low sheet resistance of 21.7 Ω/sq and an acceptable visible transmittance of 80%. The near infrared reflectance above 50% can be simultaneously obtained. The good performance of the coatings indicates that they are promising for coated glasses, thin film solar cells and heat-reflectors.     

Design of near-unity transmittance dielectric/Ag/ITO electrodes for GaN-based light-emitting diodes

We designed a near-unity transmittance dielectric/Ag/ITO electrode for high-efficiency GaN-based light-emitting diodes by using the scattering matrix method. The transmittance of an ultrathin metal layer, sandwiched between a dielectric layer and an ITO layer, was investigated as a function of the thickness and the optical constant of each constituent layer. Three different metals (Ag, Au, and Al) were examined as the metal layer. The analytical simulation indicated that the transmittance of a dielectric/metal/ITO multilayer film is maximized with an approximately 10-nm-thick Ag layer. Additionally, the transmittance also tends to increase as the refractive index of the upper dielectric layer increases. By tailoring the thickness of the dielectric layer and the ITO layer, the dielectric/Ag/ITO structure yielded a transmittance of 0.97, which surpasses the maximum transmittance (0.91) of a single ITO film. Furthermore, this extraordinary transmittance was present for other visible wavelengths of light, including violet and green colors. A complex phasor diagram model confirmed that the transmittance of the dielectric/metal/ITO multilayer film is influenced by the interference of reflected partial waves. These numerical findings underpin a rational design principle for metal-based multilayer films that are utilized as transparent electrodes for the development of efficient light-emitting diodes and solar cell devices.