From silver nanoparticles to thin films: Evolution of microstructure and electrical conduction on glass substrates

Silver nanoparticles embedded in a dielectric matrix are investigated for their potential as broadband-absorbing optical sensor materials. This contribution focuses on the electrical properties of silver nanoparticles on glass substrates at various morphological stages. The electrical current through thin films, consisting of silver nanoparticles, was characterized as a function of film thickness. Three distinct conductivity zones were observed. Two relatively flat zones (“dielectric” for very thin films and “metallic” for films thicker than 300-400 Å) are separated by a sharp transition zone where percolation dominates. The dielectric zone is characterized by isolated particle islands with the electrical conduction dominated by a thermally activated tunneling process. The transition zone is dominated by interconnected silver nanoclusters—a small increase of the film thickness results in a large increase of the electrical conductivity. The metallic conductivity zone dominates for thicknesses above 300-400 Å.     

Ginzburg-Landau simulation for a vortex around a columnar defect in a superconducting film

By means of numerical simulations based on Ginzburg-Landau theory, we study the vortex depinning from a columnar defect in a superconducting film. We evaluate the limiting thickness of the film, below which the depinning does not occur even under an application of the magnetic field perpendicular to the columnar defect. The limiting thickness is a measure of the pinning strength of the columnar defect. The dependence of this limiting thickness on the magnitude of the applied field is obtained for two types of columnar defects.     

Rapid treatment of CIGS particles by intense pulsed light

Intense pulsed light (IPL) technique has been proposed to make large grains Cu(In_0.7Ga_0.3)Se₂ (CIGS) film using CIGS particles. The proposed process is non-vacuum based and performed at room temperature without selenization treatment. Melting and recrystallization of CIGS particles to larger grains without structural deformation and phase transformation are proved with adequate characterization evidences. X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and energy dispersion analysis (EDS) were used to characterize the prepared films. Melting of the CIGS particles and recrystallization to larger grains by light energy in 20 ms short reaction time could be the reason for no structural deformation and secondary phase generation during the process. The CIGS film prepared from its constituent nanoparticles by IPL treatment has great potential for use as absorber layer for solar cell application and is expected to have large impact on cell fabrication process in terms of cost reduction and simplified processing.     

Spectroscopic characterization of Ni films on sub-10-nm silica layers: Thermal metamorphosis and chemical bonding

The thermal evolution in the chemical and physical characteristics of the Ni film of thickness 1-50 nm deposited on silica of thickness less than 10 nm was studied. The chemical composition of silica affected the thermal behavior of the Ni overlayer substantially. Nickel deposited on native oxide may diffuse downward into native oxide during annealing and was oxidized. It mainly produced Ni₃O₂ and silicides below 150 °C. Increasing the temperature to 300 °C caused further oxidation of Ni to yield NiO. The sub-10-nm silicon dioxide layer, on the other hand, can inhibit the diffusion of Ni atoms downward when the Ni-deposited sample was annealed. Instead, these atoms aggregated into small particles on the surface at elevated temperatures, causing the substrate to be exposed. The size of the particles produced can be controlled, as it increased almost linearly with the thickness of the Ni film deposited in the low thickness regime. The thinner Ni films yielded smaller, round nanoparticles with better dispersity. The particles formed were strongly adhered to the silicon dioxide surface. The bulk of the particles formed was mainly metallic. Exposing to the air of the Ni particles formed on silicon dioxide mainly produces Ni₂O₃ on the particles.     

The influence of thermal diffusion on laser ablation of metal films

Single-shot ablation thresholds of nickel and gold films in the thickness range from 50 nm to 7 m have been measured for 14 ns laser pulses at 248 nm, using photoacoustic shock wave detection in air. The metal films were deposited on fused silica substrates. The ablation threshold was found to increase linearly with film thickness up to the thermal diffusion length of the film. Beyond this point it remains independent of film thickness. The proportionality between threshold fluence and thickness allows the prediction of ablation thresholds of metal films from the knowledge of their optical properties, evaporation enthalpies and thermal diffusivities. Physically it proves that ablation is driven by the energy density determined by the thermal diffusion length. A simple thermodynamic model describes the data well. Thermal diffusivities, an essential input for this model, were measured using the technique of transient thermal gratings. In addition, the substrate dependence of the ablation threshold was investigated for 150 nm Ni films.     

On the dependence of surface undulation on film thickness

This paper investigates the dependence of surface undulation on a film thickness considerably greater than the critical value of a thin film system. It considers that surface tension and residual stress are the main cause of surface undulation. The study found that there is a critical undulation wavelength that minimizes the free energy of a thin film system, that this critical wavelength depends on the film thickness, and the effect of undulation amplitude is insignificant. The research also found that the surface undulation has a negligible influence on the residual stresses in the thin film system.     

Influence of Tb incorporation on the structural and the optical properties of ZnO nanoparticles

Structural and optical properties of the Tb doped ZnO nanoparticles are systematically studied as a function of the Tb mole-fraction. Our study suggests that the Tb incorporates mostly on the surface and affects the optical properties of the ZnO nanoparticles by influencing the attachment of certain adsorbed groups, which are found to be responsible for the appearance of a broad green luminescence (GL) band in the photoluminescence spectra recorded for these nanoparticles. It has been found that the accumulation of Tb on the surface of the nanoparticles not only enhances the band edge to green luminescence intensity ratio under the vacuum condition but also increases the band gap energy by introducing a hydrostatic compressive strain in individual nanoparticles, which provides a unique opportunity to study the pressure dependence of the optical properties of nanoparticles without applying any external pressure. The hydrostatic compressive strain is explained in terms of the increase of the surface strain energy as a result of the Tb accumulation on the surface of the nanoparticles. The average value of the surface energy density for the particles has been estimated as a function of Tb mole-fraction. The pressure coefficient of the band gap which is obtained from the variation of the band gap energy with the hydrostatic strain has been found to decrease significantly with the particle size for the ZnO nanoparticles.     

Modeling cohesive energy and melting temperature of nanocrystals

A model has been developed to account for the size dependent cohesive energy and melting temperature of nanocrystals. This model can deal with the thermodynamic properties of nanoparticles (spherical and non-spherical), nanowires and nanofilms with free surface or non-free surface (embedded in a matrix). The cohesive energy depression of nanocrystals has been predicted, and the conditions of superheating are obtained. It is found that the present theoretical results are consistent with the available experimental values.     

Ferromagnetic properties of glucose coated Cu2O nanoparticles

Magnetic properties of glucose coated cuprous oxide nanoparticles of different sizes have been studied. Unlike bulk Cu₂O, which shows diamagnetic behavior, the nanoparticles show superparamagnetic behavior. A superparamagnetic blocking temperature of 21 K is observed for 5 nm particles. A magnetic hysteresis loop with a coercivity of 406 Oe is observed for these particles at 5 K. The magnetization and the coercivity increase with decreasing particle size. The superparamagnetic behavior, along with the increase in magnetization and coercivity with decreasing particle size, is due to the enhanced surface contributions to the magnetism.     

Self-discharge performance of Ni-MH battery by using electrodes with hydrophilic/hydrophobic surface

The polytetrafluoroethylene (PTFE) and carboxymethyl cellulose (CMC) film is separately coated on the surface of the metal hydride (MH) and Ni(OH)₂ electrodes to obtain the electrodes with hydrophobic or hydrophilic surface. The effects of the surface treatment on the oxygen and hydrogen evolution from the electrodes are studied by using cyclic voltammetry tests. Although the positive and negative active materials of the Ni-MH batteries show a lower self-decomposition rate after the CMC treatment, the self-discharge rate of the batteries show little change. On the contrary, the self-discharge rate of the batteries decreases from 35.9% to 27.1% by using the PTFE-treated Ni(OH)₂ electrodes, which might be related to the suppression of the reaction between NiOOH and H₂ by the hydrophobic film.     

Film thickness dependence of electro-optic effect in epitaxial BaTiO3 thin films

Based on the phenomenological Landau-Devonshire theory, we investigate the film thickness dependence of ferroelectric and electro-optic properties of epitaxial BaTiO₃ thin films grown on SrTiO₃ and MgO substrates. By using the effective substrate lattice parameter concept, the film thickness dependence of misfit strain is incorporated into the theory. Therefore, the film thickness dependence of ferroelectric and electro-optic properties in epitaxial BaTiO₃ thin films can be explained. Moreover, a large quadratic electro-optic effect was obtained in the BaTiO₃ thin films, which is in good agreement with the experimental result of BaTiO₃ thin films on the MgO substrate.     

Optical properties of sol-gel fabricated Ni/SiO2 glass nanocomposites

Nickel nanoparticles were grown in silica glass by annealing of the sol-gel prepared silicate matrices doped with nickel nitrate. TEM characterization of Ni/SiO₂ glass proves the formation of isolated spherical nickel nanoparticles with mean sizes 6.7 and 20 nm depending on annealing conditions. The absorption and photoluminescence spectra of Ni/SiO₂ glasses were measured. In the absorption spectra, we observed the band related to the surface plasmon resonance (SPR) in Ni nanoparticles. The broadening of SPR was observed with decrease of Ni nanoparticle size. The width of the surface plasmon band decreases 1.5 times at the lowering of temperature from 293 to 2 K because of strong electron-phonon interaction. The spectra proved the creation of nickel oxide NiO clusters and Ni²⁺ ions in silica glass as well.     

Spatially controlled dissolution of Ag nanoparticles in irradiated SiO2 sol-gel film

In this paper, we report the spatially controlled dissolution of silver nanoparticles in irradiated SiO₂ sol-gel films. The Ag nanoparticles have been formed in the sol-gel solution before the film deposition by adding Triton and ascorbic acid and also after the film deposition using a heat treatment at 700 °C for few minutes or at 550 °C for 6 h in reducing atmosphere. Using a spectrometer, a new view white light interferometer and a micro-thermal analyzer, we demonstrate that the silver nanoparticles can be dissolved using a continuous black ray UV lamp or with a near-infrared (NIR) femtosecond laser, due to a significantly increase in the local temperature. We confirm that the micro-thermal analyzer can be used as a new tool to study the dissolution of metallic nanoparticles in thin film if located at the surface of the films.     

Surface modification with EDTA molecule: A feasible method to enhance the adsorption property of ZnO

Surface-functionalized zinc oxide (ZnO) nanoparticles were synthesized with ethylene diamine tetraacetic acid (EDTA) as a modification agent, which were used as adsorbents in the adsorption of Cu²⁺ at certain conditions. The transmission electron microscopy (TEM) results show that the average size of ZnO particles is about 45 nm, and it exhibits hexagonal wurtzite structure. Fourier transform infrared (FTIR) spectra reveal that the EDTA species are chemically bonded on the surface of ZnO. Compared with bare ZnO particles, the functionalized ZnO nanoparticles have a better activity in the Cu²⁺ adsorption. The maximum adsorption capacity of functionalized ZnO nanoparticles is 20.97 mg/g, while it is 17.93 mg/g for the bare ZnO. The adsorption isotherm of bare ZnO particles is in accordance with the Freundlich model, and the chemical adsorption is in a dominant position in the adsorption process of Cu²⁺ on functionalized ZnO particles.     

Investigations of magnetic and dielectric properties of cupric oxide nanoparticles

Cupric oxide nanoparticles of ∼8-10 nm width and 40-45 nm length self assembled as large particles ∼1-1.5 μm have been investigated, in the 10-325 K temperature range, using magnetic and dielectric measurements. In magnetic measurements a single broad peak at ∼230 K in a zero field cooled sample has been observed. Coercivity, in magnetization measurements at 10 K, suggests that the nanoparticles are core-shell type particles with an antiferromagnetic core and a ferromagnetic shell. Dielectric measurements, at various frequencies from 3.7 Hz to 949 kHz, exhibit a sharp peak at 284 K followed by weak anomalies around 213 and 230 K.     

Fluorescent photoswitchable nanohybrids based on photochromism

A new type of fluorescent photoswitchable nanohybrids based on photochromism has been assembled, in which hydrophobic diarylethene and matched fluorescent dye are assembled in the nanoscale crosslinked polymeric matrix via a modified miniemulsion polymerization process and a seeded polymerization technique. The nanohybrids exhibited excellent fluorescent photoswitchable action owing to efficient photoinduced energy transfer whether the nanohybrids as nanoparticles dispersed in water or in a polymer film, and the improved photo-thermal stability of both essential components could be readily achieved. Importantly, our assembling approach is much simpler than the covalent chemical synthesis, and is a general method for other hydrophobic photochromic compounds.     

Magnetic properties of self-assembled nanostructure films on the base of amorphous Ni granules

We report on structural and magnetic properties of granular films consisting of 2.5 nm Ni nanoparticles. The films are fabricated by the original laser electrodispersion technique, which allows producing nearly monodisperse and amorphous particles. Atomic force microscopy (AFM) study shows that in 8 nm thickness films the particles are self-assembled in clusters with the lateral size 100-150 nm and the height of about 8 nm. Performed by SQUID, the films magnetization measurements reveal superparamagnetic behaviour, characteristic for an ensemble of non-interacting single domain magnetic particulates. It is found that the magnetic moment of the particulate is equal to that of about 3000 individual Ni nanoparticles and the blocking temperature is close to room temperature. Defined from magnetic measurements, the size of single domain particulates correlates well with the size of the clusters determined from AFM images. We propose that exchange interaction plays an important role in the formation of the particulates by aligning the magnetic moments of the individual Ni nanoparticles inside the clusters. Presence of magnetic clusters with high blocking temperature makes the fabricated films potentially useful for high-density magnetic data storage applications.     

Synthesis and magnetic properties of size-controlled FeNi alloy nanoparticles attached on multiwalled carbon nanotubes

FeNi alloy nanoparticles with controllable sizes were attached on the multiwalled carbon nanotubes by adjusting the atomic ratio of metal to carbon in the mixed solution of nitrate with Fe:Ni=1:1 (atomic ratio) via wet chemistry. Transmission electron microscopy (TEM) and high-resolution TEM indicated that quasi-spherical FeNi alloy nanoparticles with sizes in the range 12-25 nm are obtained. FeNi alloy composed of major face center cubic (fcc) and minor body center cubic (bcc) structures, which is proved by the X-ray powder diffraction (XRD). Magnetization measured by vibrating sample magnetometer demonstrated that both the coercive force and saturation magnetizations decrease as the size of the FeNi alloy nanoparticles decreased. The chemical method is promising for fabricating FeNi alloy nanoparticles attached on carbon nanotubes for magnetic storage and ultra high-density magnetic recording applications.     

Size-dependent nanoparticle reaction enthalpy: Oxidation of aluminum nanoparticles

Here we present a model describing the particle size dependence of the oxidation enthalpy of aluminum nanoparticles. The model includes the size dependence of the cohesive energy of the reactant particles, the size dependence of the product lattice energy, extent of product agglomeration, and surface capping effects. The strongest effects on aluminum nanoparticle energy release occur for particle diameters below 10 nm, with enhanced energy release for agglomerated oxide products and decreased energy release for nanoscale oxide products. An unusual effect is observed with all nanoparticle reaction enthalpies converging to the bulk value when agglomeration of the products approaches the transition between nanoparticle→nanoparticle and nanoparticle→bulk energetics. Optimal energy output for Al NP oxidation should occur for sub-10-nm particles reacting with significant agglomeration.     

A layer of reduced switchable polarisation in (Pb,La)TiO3 films leading to a thickness dependence of the ferroelectric parameters

Two sets of ferroelectric (Pb,La)TiO₃ thin films have been prepared by a diol-based sol-gel technique by varying the heating rate to the crystallisation temperature of 650°C. Films of increasing thickness were obtained by repeating the solution deposition from 1 to 5 times. The switchable polarisation was evaluated from hysteresis loops and from the integration of the switching current transients during pulse tests, and was found to significantly depend on film thickness. Measurements of the thickness dependence of the reciprocal capacitance and Rutherford backscattering spectrometry results indicate that a layer with different dielectric permittivity, and composition for one set of films, existed next to the bottom electrode. In the one set of films it originated because of interdiffusion between the film and the substrate, while in the other set, it was linked to the tensile stress at the film/substrate interface. These layers had a reduced switchable polarisation, which caused the observed dependence of their properties on thickness.