Electrical properties of SrBi2(Nb0.5Ta0.5)2O9 ceramics

Aurivillius SrBi₂(Nb_0.5Ta_0.5)₂O₉ (SBNT 50/50) ceramics were prepared using the conventional solid-state reaction method. Scanning electron microscopy was applied to investigate the grain structure. The XRD studies revealed an orthorhombic structure in the SBNT 50/50 with lattice parameters a=5.522 Å, b=5.511 Å and c=25.114 Å. The dielectric properties were determined by impedance spectroscopy measurements. A strong low frequency dielectric dispersion was found to exist in this material. Its occurrence was ascribed to the presence of ionized space charge carriers such as oxygen vacancies. The dielectric relaxation was defined on the basis of an equivalent circuit. The temperature dependence of various electrical properties was determined and discussed. The thermal activation energy for the grain electric conductivity was lower in the high temperature region (T>303.6 °C, E_a−ht=0.47 eV) and higher in the low temperature region (T<303.6 °C, E_a−lt=1.18 eV).     

Micromechanical and thermal behaviour of gel grown pure- and sodium-modified copper tartrate crystals

Results regarding micromechanical characteristics of gel grown pure- and sodium-modified copper tartrate crystals, bearing composition CuC₄H₄O₆·3H₂O, (Cu)_0.77(Na)_0.23C₄H₄O₆·3H₂O and (Cu)_0.65(Na)_0.35C₄H₄O₆·H₂O, as obtained on using indentation induced hardness testing technique are reported. Thermal behaviour of these crystals in the temperature ranging from room temperature (∼25 °C) to about 600 °C is also reported. Pure copper tartrate crystals are found to be thermally more stable than the sodium-modified ones. Dependence of Vickers’ hardness number H_v on load ranging from 0.049 to 2.94 N on two different planes for all the three compositions is analyzed. It is shown that after initial rise in the value of H_v, the same achieves saturation at a load of 0.49 N. Modification of copper tartrate crystal by introducing sodium in its lattice brings about a change in the micromechanical characteristics. The saturation value of H_v decreases with increase in the concentration of sodium ions. The results on (0 0 1) and (1 1 1) planes for both pure and modified copper tartrate crystals suggest hardness anisotropy. Relative difference of hardness between the two planes and yield strength for both pure and modified copper tartrate crystals is worked out. The experimental results are analyzed for applicability of Meyer’s law and Proportional Specimen Resistance Model. It is suggested that the experimental results indicating reverse ISE phenomenon may be explained in terms of the existence of a distorted zone near the crystal-medium interface. The integral method of Coats and Redfern approximation applied to the thermoanalytical data suggests “Random Nucleation Model” for the reaction kinetics of these crystals. Non-isothermal kinetic parameters such as activation energy, frequency factor and order of reaction are calculated.     

Studies on vibrational, dielectric, mechanical and thermal properties of organic nonlinear optical co-crystal: 2,6-diaminopyridinium-4-nitrophenolate-4-nitrophenol

This article presents the vibrational, dielectric, mechanical and thermal properties of 2,6-diaminopyridine-4-nitrophenolate-4-nitrophenol co-crystals (DAP:NP) grown by slow evaporation solution growth technique. It crystallizes in orthorhombic noncentrosymmetric space group Pna2₁ with cell dimension a=10.86 Å, b=12.00 Å and c=13.53 Å; α=β=γ=90° with V=1764 Å³. Functional groups present in the molecule have been identified from FTIR study. Dielectric constant (ε_r), dielectric loss (tanδ) and ac conductivity (σ_ac) behaviors of the crystals have been studied at different temperatures. Presence of piezoelectric resonance peaks at lower frequency in dielectric measurements may increase the electro-optic coefficient of the crystals. Mechanical strength and its parameters of the grown crystals have been determined by Vickers microhardness test. TG/DTA analysis shows the melting point of the material is 150 °C and it undergoes two stages of decomposition.     

Densification, microstructural evolution, and dielectric properties of CaTiO3-LaGaO3 microwave ceramics

The relations among the densification, microstructural evolution, and microwave dielectric properties of the (1−x)CaTiO₃-xLaGaO₃ ceramics with x=0.34 and 0.36 were investigated in this study. The results indicated that (1−x)CaTiO₃−xLaGaO₃ ceramics can be densified at 1300 °C with at least 97% of the theoretical value. The ceramics reported an orthorhombic perovskite structure, and no other detectable phases were found. Both ε_r and Q×f values can be improved by slowing the cooling rate during sintering. The ε_r and Q×f values of the 0.64CaTiO₃-0.36LaGaO₃ ceramics at cooling rates of >10 °C/min and 0.1 °C/min are 48.1 and 27,500 and 48.7 and 38,000, respectively. The higher densification obtained at a slower cooling rate plays an important role in improving the microwave dielectric properties.     

Iminodiacetic acid doped ferroelectric triglycine sulphate crystal: Crystal growth and characterization

Single crystals of iminodiacetic acid (HN(CH₂COOH)₂) doped triglycine sulphate (IDATGS) crystals have been grown from aqueous solution containing 1-10 mol% of iminodiacetic acid at constant temperature by slow evaporation technique. The effects of different amounts of doping entities on the growth habit have been investigated. X-ray powder diffraction pattern for pure and doped TGS was collected to determine the lattice parameters. The grown crystals were subjected to Fourier transform infrared (FTIR) spectroscopy studies to find the presence of various functional groups qualitatively. The dielectric permittivity has been studied as a function of temperature. An increase in the transition temperature (49.2-49.7 °C) of IDATGS crystals is observed. The dielectric constant (ε′_max) of IDATGS crystals vary in the range 922-2410 compared to pure TGS (T_c=49.12 °C and ε′_max=3050). Curie Weiss constants C_p and C_f in the paraelectric and ferroelectric phases were determined. The transition temperature (T_c) is found to decrease with increase in dopant concentration. P-E hysteresis studies show the presence of internal bias field in the crystal. Piezoelectric measurements were also carried out at room temperature. Domain patterns on b-cut plates were observed using scanning electron microscope. The micro hardness studies reveal that the doped crystals are harder than the pure TGS crystals. The low dielectric constant, higher transition temperature, internal bias field and hardness suggest that IDATGS crystals could be a potential material for IR detectors.     

Full potential calculation of structural, elastic properties and high-pressure phase of binary noble metal carbide: ruthenium carbide

We present in this paper the results of an ab initio theoretical study within the local density approximation (LDA) to determine in rock-salt (B1), cesium chloride (B2), zinc-blende (B3), and tungsten carbide (WC) type structures, the structural, elastic constants, hardness properties and high-pressure phase of the noble metal carbide of ruthenium carbide (RuC).The ground state properties such as the equilibrium lattice constant, elastic constant, the bulk modulus, its pressure derivative, and the hardness in the four phases are determined and compared with available theoretical data. Only for the three phases B1, B3, and WC, is the RuC mechanically stable, while in the B2 phase it is unstable, but in B3 RuC is the most energetically favourable phase with the bulk modulus 263 GPa, and at sufficiently high pressure (P_t=19.2 GPa) the tungsten carbide (WC) structure would be favoured, where ReC-WC is meta-stable.The highest bulk modulus values in the B3, B2, and WC structures and the hardnesses of H(B3)=36.94 GPa, H(B1)=25.21 GPa, and H(WC)=25.30 GPa indicate that the RuC compound is a superhard material in B3, and is not superhard in B1 and WC structures compared with the H(diamond)=96 GPa.     

Electrical properties of high Curie temperature (1−x)Pb(In1/2Nb1/2)O3-xPbTiO3 single crystals grown by the solution Bridgman technique

0.65Pb(In_1/2Nb_1/2)O₃-0.35PbTiO₃ (PINT65/35) (starting composition) single crystals were grown successfully through the solution Bridgman technique using PbO flux and PMNT67/33 seed crystals. Because of the composition variation, the final composition of achievable crystals is in a range of 0.32-0.34 with the corresponding T_c range of 265-269 °C. The (001) plates of as-grown PINT66/34 single crystals show high Curie temperature (T_c=269 °C) and rhombohedral-tetragonal phase transition temperature (T_rt=134 °C). Besides, good electrical properties with high dielectric constant (ε>3000), low dielectric loss (tan δ∼1.2%), high piezoelectric constant (d₃₃∼2000 pC/N) and large electromechanical coupling factor (k_t≈59%) at room temperature have been obtained on the (001) plates. The sound velocity, acoustic impedance and other piezoelectric parameters were also measured on the (001) plates in this study, which provide us more detailed information about PINT66/34 single crystals.     

Growth and characterization of a new organic NLO material: Glycine nitrate

Single crystals of glycine nitrate [(C₂H₆NO₂)⁺ · (NO₃)⁻] were grown using submerged seed solution method. The crystals were characterized by using single crystal X-ray diffraction and density measurements. Spectroscopic, thermal and optical studies were carried out for analyzing the presence of the functional groups, thermal stability, decomposition and transparency of the sample. These studies showed that the crystals are thermally stable upto 145 °C and transparent for the fundamental and second harmonic generation of Nd:YAG (λ = 1064 nm) laser. Second harmonic generation (SHG) conversion efficiency was investigated to explore the NLO characteristics of this material. Microhardness and dielectric studies were also carried out.     

The role of As2O3 on the stability and some physical properties of PbO-Sb2O3 glasses

PbO-Sb₂O₃ glasses added with different concentrations of As₂O₃ (10-55 mol%) were prepared to understand their IR spectra, elastic properties (Young's modulus E, Shear modulus G, microhardness H), optical absorption and dielectric properties (constant ε, loss tan δ, ac conductivity σ_ac over a moderately wide range of frequency and temperature and breakdown strength in air medium at room temperature). Results have indicated that the structure of the PbO-Sb₂O₃-As₂O₃ glass is more rigid when the concentration of As₂O₃ is around 40 mol%.     

Low-temperature sintering and microwave dielectric properties of Ca2Zn4Ti15O36 ceramics

The sintering behavior, microstructures, and microwave dielectric properties of Ca₂Zn₄Ti₁₅O₃₆ ceramics with B₂O₃ addition were investigated. The crystalline phases and microstructures of Ca₂Zn₄Ti₁₅O₃₆ ceramics with 0-10 wt% B₂O₃ addition were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The sintering temperature of Ca₂Zn₄Ti₁₅O₃₆ ceramic was lowered from 1170 to 930 °C by 10 wt% B₂O₃ addition. Ca₂Zn₄Ti₁₅O₃₆ ceramics with 8 wt% B₂O₃ addition sintered at 990 °C for 2 h exhibited good microwave dielectric properties, i.e., a quality factor (Qf) 11,400 GHz, a relative dielectric constant (ε_r) 41.5, and a temperature coefficient of resonant frequency (τ_f) 94.4 ppm/°C.     

Characterization, sintering and dielectric properties of nanocrystalline zinc oxide prepared by a citric acid-based combustion route

Nanosized zinc oxide has been synthesized through a novel single step solution combustion route using citric acid as fuel. The X-ray diffraction (XRD) analysis revealed that the synthesized ZnO nanopowder has the pure wurtzite structure. The phase purity of the nanopowder has been confirmed using differential thermal analysis (DTA), thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FT-IR). The morphology and crystalline size of the as-prepared nanopowder characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that the powder consisted of a mixture of nanoparticles and nanorods. The nanocrystalline ZnO could be sintered to ∼97% of the theoretical density at 1200 °C in 4 h. The dielectric constant (ε_r) and dielectric loss (ε_i) of sintered ZnO pellets at 5 MHz were 1.38 and 9×10⁻², respectively, at room temperature.     

Fiber laser annealing of nanocrystalline PZT thick film prepared by aerosol deposition

Nanocrystalline PZT thick films (1 mm square and over 10 μm thick) directly deposited onto stainless-steel substrates (PZT/SUS) by aerosol deposition (AD) technique and then annealed using focused laser beam with a fiber laser to suppress thermal damage to the back sides of the PZT/SUS and substrate near the film edge and to retain the dielectric and/or ferroelectric properties of the PZT/SUS. Compared with CO₂ laser annealing, fiber laser annealing suppressed thermal damage to the substrate. Compared with PZT/SUS annealed at 600 °C using an electric furnace, PZT/SUS annealed at 600 °C using a fiber laser showed superior properties, namely, dielectric constant ? > 1200 at a frequency of 100 Hz, remanent polarization P_r > 30 μC/cm², and coercive field strength E_c < 50 kV/cm at a frequency of 10 Hz. Furthermore, the grain growth for the PZT/SUS formed by AD technique and annealed by fiber laser irradiation was occurred within the laser spot size.     

Thermochemical behavior of metallic citrate precursors for the production of pure LaAlO3

Pure LaAlO₃ nanoparticles were synthesized, using a citrate-precursor technique. La(NO₃)₃, Al(NO₃)₃, and C₃H₄(OH)(COOH)₃, in a molar ratio of 1:1:4.5, were dissolved in deionized water. The pH of the aqueous solution was adjusted using NH₄OH. After drying, the citrate precursors were charred at 350 °C, followed by calcination at different temperatures. The thermochemical behavior of the charred citrate precursor to form LaAlO₃ was investigated using X-ray diffractometry, infrared spectroscopy, thermogravimetric analysis, and differential thermal analysis. While the charred specimen obtained at pH=2 (without NH₄OH addition) was composed of LaAl(OOCH₂)₃, the charred specimens obtained at pH>2 were composed of LaAlO_3−x−y(CO₃)_x(OH)_2y. All these metallic salts were decomposed at temperatures between 600 and 780 °C to form crystalline LaAlO₃ but calcining the specimens in air at ?800 °C were required to remove all residual chars to produce pure LaAlO₃. At 900 °C, the citrate-derived particles obtained at pH>2 were composed of LaAlO₃ crystallites with an average size of ∼30 nm.     

Fluorophosphate glasses containing manganese

New fluorophosphate glasses based on MnF₂, NaPO₃ and MF_n (M=Zn²⁺, Sr²⁺, Mg²⁺, Ba²⁺, Li⁺, Na⁺ and K⁺) have been synthesised and characterized. Large vitreous areas were observed. Samples of 4 mm in thickness have been obtained. These glasses are easy to prepare and stable in ambient air. Depending on the composition and the nature of the M cation, glass transition temperature, T_g, lies between 230 and 314 °C, crystallisation temperature, T_x is between 320 and 475 °C. These glasses are pink coloured, and infrared transmission extends up to 4.5 μm with extrinsic OH⁻ absorption band at 3200 cm⁻¹ and other bands around 2200 and 1600 cm⁻¹ that relate to PO₄ tetrahedron vibration. Other physical properties including density, microhardness, Young modulus, thermal expansion and refractive index were investigated and correlated to composition.     

Synthesis, growth and characterization of novel second harmonic nonlinear chalcone crystal

Nonlinear optical (NLO) materials are useful in many of the industrial applications. New NLO chalcone derivative (2E)-3-[4-(methylsulfanyl)phenyl]-1-(4-nitrophenyl)prop-2-en-1-one (4N4MSP) crystals have been grown by slow evaporation technique at ambient temperature. The grown crystals were subjected to single crystal X-ray diffraction study. The crystal has noncentrosymmetric structure in the orthorhombic system with space group Aba2 and unit cell parameters a=14.0647(15) Å, b=33.738(4) Å and c=6.0039(6) Å. To confirm the presence of various functional groups in the compound, FT-IR spectrum was recorded. The crystal was subjected to TGA/DTA analysis to find its thermal stability. The grown crystals were characterized for their optical transmission and mechanical hardness. The second harmonic generation (SHG) efficiency of the crystal is obtained by classical powdered technique using Nd:YAG laser and its value is 28.57 times that of urea. The laser damage threshold for 4N4MSP crystal was determined using Q-switched Nd:YAG laser. The refractive index values for green and red wavelengths were measured by Brewster angle technique. The dielectric and electrical measurements were carried out to study the different polarization mechanism and conductivity of the crystal. Good thermal, mechanical, transmission and SHG response make it desirable for the NLO applications.     

Microstructure and antibacterial properties of microwave plasma nitrided layers on biomedical stainless steels

Nitriding of AISI 303 austenitic stainless steel using microwave plasma system at various temperatures was conducted in the present study. The nitrided layers were characterized via scanning electron microscopy, glancing angle X-ray diffraction, transmission electron microscopy and Vickers microhardness tester. The antibacterial properties of this nitrided layer were evaluated. During nitriding treatment between 350 °C and 550 °C, the phase transformation sequence on the nitrided layers of the alloys was found to be γ → (γ + γ_N) → (γ + α + CrN). The analytical results revealed that the surface hardness of AISI 303 stainless steel could be enhanced with the formation of γ_N phase in nitriding process. Antibacterial test also demonstrated the nitrided layer processed the excellent antibacterial properties. The enhanced surface hardness and antibacterial properties make the nitrided AISI 303 austenitic stainless steel to be one of the essential materials in the biomedical applications.     

Electrical and electromechanical properties of lead-potassium-yttrium-niobate ceramics—piezoelectric applications

Tungsten bronze (TB)-type oxide ceramic Pb_0.74K_0.13Y_0.13Nb₂O₆ (PKYN) has been synthesized by the standard solid state reaction method. Single phase formation, orthorhombic crystal structure was confirmed by X-ray diffraction (XRD). The substitution of Y³⁺ in Pb_0.74K_0.52Nb₂O₆ (PKN) decreased the unit cell volume and T_C=260 °C. PKYN exhibited the remnant polarization, P_r=8.5 μC/cm², and coercive field, E_c=28.71 kV/cm. Electrical spectroscopy studies were carried out over the temperature (35-595 °C) and frequency (45 Hz-5 MHz) ranges, and the charge carrier phenomenon, grain-grain boundary contribution and non-Debye-type relaxation were analyzed. The relaxation species are immobile charges in low temperature and oxygen vacancies at higher temperature. The theoretical values computed using the relations, ε′=ε_∞+sin(n(T)π/2)(a(T)/ε₀)(ω^n(T)−1); σ(ω)=σ_dc+Aωⁿ are fitted with the experimental one. The n and A parameters suggested that the charge carrier's couple with the soft mode and become mobile at T_C. The activation enthalpy, H_m=0.38 eV, has been estimated from the hopping frequency relation ω_p=ω_e exp(−H_m/k_BT). The piezoelectric constants K_t=35.4%, d₃₃=69×10⁻¹² C/N, d₃₁=−32×10⁻³ mV/N, S₁₁^E=17.8 pm²/N, etc., achieved in PKYN indicate the material is interesting for transducer applications. The activation energies from different formalisms confirmed the ionic-type conduction.     

Identification of optical nonlinearities of dye-doped nematic and polymer-dispersed liquid crystals using Z-scan technique

This study investigates the nonlinear optical properties of azo-dye-doped nematic and polymer-dispersed liquid crystal (ADDPDLC) films with nano-sized LC droplets using the Z-scan technique, which is a simple but powerful technique for measuring the optical Kerr constants of materials. The results indicate that the optical Kerr constant (n₂) of the azo-dye-doped nematic LC (ADDLC) film is large because of the photoisomerization effect and the thermal effect. Therefore, the optical Kerr constant of this material can be modulated by varying the temperature of the sample and the direction of polarization of incident laser. The range of n₂ modulated is from −5.26 × 10⁻³ to 1.62 × 10⁻³ cm²/W. The optical Kerr constants of ADDPDLC films at various temperatures are also measured. The experimental results reveal that liquid crystals in the ADDPDLC film strengthen the nonlinearity. The n₂ of the ADDPDLC film is maximal at ∼35 °C, because of the decrease in the clearing temperature of the ADDPDLC films. The clearing temperatures of the liquid crystals (E7), and the ADDPDLC film used in this work were found to be 61 °C and 43 °C, respectively.     

Characterization of ZrB2(0 0 0 1) surface prepared by ex situ HF solution treatment toward applications as a substrate for GaN growth

ZrB₂(0 0 0 1) crystals grown by the rf-floating zone technique were characterized by X-ray photoelectron spectroscopy, reflection high-energy electron diffraction, and atomic force microscopy. These characteristics were investigated as a function of thermal cleaning temperature up to 1000 °C in vacuum for as-received substrates as well as substrates treated ex situ in HF aqueous solution. The HF treatment process removed the ZrO₂ native oxide layer present on as-received substrates and resulted in ZrB₂(0 0 0 1) surfaces exhibiting long-range order. Upon annealing the HF-treated surface in high vacuum, two types of reconstructions were observed: an incommensurate reconstruction from 650 to 900 °C related to residual H₂ gas, and n × n reconstructions at 1000 °C, possibly related to oxygen.     

Effect of sintering temperature on the structural, dielectric and ferroelectric properties of tungsten substituted SBT ceramics

Structural, dielectric and ferroelectric properties of tungsten (W) substituted SrBi₂(Ta_1−xW_x)₂O₉ (SBTW) [x=0.0, 0.025, 0.05, 0.075, 0.1 and 0.2] have been studied as a function of sintering temperature (1100-1250 °C). X-ray diffraction patterns confirm the single-phase layered perovskite structure formation up to x=0.05 at all sintering temperatures. The present study reveals an optimum sintering temperature of 1200 °C for the best properties of SBTW samples. Maximum T_c of ∼390 °C is observed for x=0.20 sample sintered at 1200 °C. Peak-dielectric constant (ε_r) increases from ∼270 to ∼700 on increasing x from 0.0 to 0.20 at 1200 °C sintering temperature. DC conductivity of the SBTW samples is nearly two to three orders lower than that of the pristine sample. Remnant polarization (P_r) increases with the W content up to x≤0.075. A maximum 2P_r (∼25 μC/cm²) is obtained with x=0.075 sample sintered at 1200 °C. The observed behavior is explained in terms of improved microstructural features, contribution from the oxygen and cationic vacancies in SBTW. Such tungsten substituted samples sintered at 1200 °C exhibiting enhanced dielectric and ferroelectric properties should be useful for memory applications.