Miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends by transesterification

The effects of transesterification on the miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) were studied. Blends were obtained by solution precipitation at room temperature to avoid transesterification during blend preparation. The physical blends and transesterified products were analyzed by wide-angle x-ray scattering, differential scanning calorimetry, and nuclear magnetic resonance spectroscopy. It was found that the physical blends are immiscible and when the extent of transesterification reaches 50% of the completely randomized state, independent of blend composition, the blends are not crystallizable and show a single glass transition temperature between those of starting polymers. The interchange reactions were significantly influenced by annealing temperature and time but negligibly by blend composition. © 1996 John Wiley & Sons, Inc.     

Complete miscibility of ternary aryl polyesters demonstrating a new criterion and horizon for miscibility characterization

A ternary miscible blend system comprising only crystallizable aryl polyesters [poly(ethylene terephthalate), poly(trimethylene terephthalate), and poly(butylene terephthalate)] was characterized with the criteria of thermal analyses, microscopy, and X‐ray characterizations. The reported ternary miscibility (in the quenched amorphous state of blends of the three aryl polyesters) was truly physical and under the condition of no chemical transesterifications; this justified that transesterification was not a necessary condition for miscibility in polyester blends in this case. This study further proposed and tested a novel concept of a new criterion for miscibility characterization for polymer blends of only crystallizable polymers. A single composition‐dependent cold‐crystallization‐temperature (T_cc) peak in blends of only semicrystalline polymers was taken as an indication of an intimate mixing state of miscibility. The theoretical background for establishing the single composition‐dependent T_cc peak as a valid miscibility criterion for crystallizable polymer blends was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2394–2404, 2003     

Biodegradable poly(alkylene succinate) blends: Thermal behavior and miscibility study

New binary blends composed of poly(ethylene succinate) and poly(propylene succinate) or poly(ethylene succinate) and poly(butylene succinate) were prepared. Both PESu/PPSu and PESu/PBSu systems belong to semicrystalline/semicrystalline pairs. The miscibility and crystallization behavior was investigated using differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and polarizing light microscopy (PLM). Blends of PESu and PPSu exhibited a single composition dependent glass transition temperature over the entire range of composition, indicating that the system is miscible. The melting point depression of the high melting temperature component, PESu, was analyzed according to the Nishi‐Wang equation. A negative polymer–polymer interaction parameter was obtained, indicating that the blends are thermodynamically miscible in the melt. The two components crystallized sequentially when the blends were cooled rapidly to a low temperature. DSC traces of PESu/PBSu blends after quenching showed two distinct composition dependent glass transition temperatures between those of the neat polymers, showing that the polymers are partially miscible. The amorphous PESu/PBSu blends in the intermediate compositions showed three cold‐crystallization peaks, indicating the influence of mixing. The crystallization rates of PBSu were reduced and those of PESu were increased. WAXD showed reduced crystallinity and peak broadening in the patterns of the blends of intermediate compositions, while no spherulites could be detected by PLM. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 584–597, 2006     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

TMDSC and Atomic Force Microscopy Studies of Morphology and Recrystallization in Polyesters Including Oriented Films

The thermal and crystal morphological properties of poly[ethylene teraphthalate] (PET) and poly(ethylene-2,6-naphthalenedicarboxylate) (PEN) biaxially oriented films were compared to amorphous and other isotropic semi-crystalline samples. Crystal melting as a function of temperature was characterized by temperature modulated DSC (TMDSC) and found to begin just above the glass transition for both oriented films. About 75°C above the glass transitions, substantial exothermic recrystallization begins and continues through the final melting region in oriented films. The maximum in the non-reversing TMDSC signal for the oriented films signifies the maximum recrystallization exothermic activity with peaks at 248°C and 258°C for PET and PEN, respectively. The final melting endotherm detected was 260°C and 270°C for PET and PEN, and is shown by the TMDSC data and by independent rapid heating rate melting point determinations to be due to the melting of species recrystallized during the heating scan. The results are compared with TMDSC data for initially amorphous and melt crystallized samples. The volume fraction of rigid species (F_rigid=total crystal fraction plus rigid amorphous or non-crystalline species) were measured by TMDSC glass transition data, and contrasted with the area fraction of rigid species at the oriented film surface characterized with very high resolution atomic force microscopy (AFM) phase data. The data suggest that the 11 nm wide hard domains in PET, and 21 nm wide domains in PEN film detected by AFM consist of both crystal and high stiffness interphase species.This revised version was published online in November 2005 with corrections to the Cover Date.     

Crystallization and melting behaviour of poly(m-xylene adipamide)

The melting and crystallisation behaviour of poly(m-xylene adipamide) (MXD6) are investigated by using the conventional DSC, X-ray diffraction and polarised light microscopy. Triple, double or single melting endotherms are obtained in subsequent heating scan for the samples after isothermal crystallisation from the melt state at different temperatures. The lowest melting peak can be ascribed to the melting of secondary crystals. The melting of primary crystals causes the medium melting peak and the highest melting peak is attributed to the melting of recrystallised species formed during heating. Following the Hoffman–Weeks theory, the equilibrium melting temperature is equal to 250°C and the equilibrium melting enthalpy ΔH _m ⁰ to 175 J g^–1. Then, using the Lauritzen–Hoffmann theory of secondary crystallisation, the analyse of the spherulitic growth shows that the temperature of transition between the growing regimes II and III is equal to 176°C. Finally the Gibbs-Thomson relationship allows the determination of the distribution function of crystalline lamellae.     

Supramolecular poly(ether ketone)–polyisobutylene pseudo‐block copolymers

The association behavior of telechelic hydrogen‐bonded poly(ether ketone) (PEK) and polyisobutylene (PIB) polymers and the formation of a new class of pseudo‐block copolymers is reported. The attachment of complementing hydrogen bonds (thymine/2,6‐diaminotriazine and cytosine/2,6‐diaminotriazine) onto the respective PIB and PEK polymers leads to a dramatic increase in the miscibility between the normally immiscible PEK and PIB polymers. The structure formation in the liquid state was studied by dynamic NMR spectroscopy as well as in the solid state via solid‐state NMR‐spectroscopy, DSC, and TEM methods. The polymers form a nanophase structure with a periodicity of 70 nm with the microphase separation occurring specifically within the donor–acceptor pair with the higher binding constant (thymine/2,6‐diaminotriazine) and not within the weaker bonded cytosine/2,6‐diaminotriazine pair. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 162–172, 2004     

Investigation of Progesterone Loaded Poly(D,L-Lactide) Microspheres Using TMDSC,SEM and PXRD

Poly(d,l-lactide) microspheres with progesterone loadings of 0, 10, 20, 30 and 50% w/w were manufactured using an interrupted solvent evaporation process. Spherical microspheres with loadings close to the theoretical values were produced. The glass transition of the polymer could be identified by a step change in the heat capacity measured by TMDSC. Progesterone was found to plasticise the glass transition temperature at contents of 20% w/w or less. At a 30% loading, cold crystallisation of progesterone was seen indicating that an amorphous form of the drug was present; these microspheres were found to exhibit a pitted surface. TMDSC of the 50% progesterone samples suggested that most of the drug was present as crystals. This was supported by the SEM and PXRD results. This revised version was published online in July 2006 with corrections to the Cover Date.     

Blends of a novel high-temperature poly(oxy-1,4′-diphenyleneoxy-1,4-phenylenecarbonyl-1,4-phenylene) with poly(ether imide): structure, interaction, and miscibility

 Polymer miscibility has been discovered in a blend system comprising poly(ether imide) (PEI) and a new poly(ether diphenyl ether ketone) (PEDEK). The miscibility of the PEDEK/PEI polymer system (quenched from the molten state) was investigated in this study using differential scanning calorimetry and Fourier transform (FT-IR) spectroscopy. A composition-dependent single glass-transition temperature (T _g) in the PEDEK/PEI blends over a full composition range was observed; the sharp transition width and the T _g–composition relationship both suggest that the scale of mixing is fine and uniform. Evidence based on observation of the cold-crystallization peak and suppression of the blend crystallinity and melting peak also indicated intimate intermolecular mixing. The FT-IR result yielded further evidence that the physical interactions leading to miscibility were weak, with no apparent specific interactions between the constituent polymers. Relationships between structures and interactions responsible for the miscibility in PEI and several ether-ketone-type polymers are briefly discussed. Received: 8 July 1999 Accepted in revised form: 21 October 1999     

Reversible and irreversible heat capacity of poly(trimethylene terephthalate) analyzed by temperature‐modulated differential scanning calorimetry

The heat capacity of poly(trimethylene terephthalate) (PTT) has been analyzed using temperature‐modulated differential scanning calorimetry (TMDSC) and compared with results obtained earlier from adiabatic calorimetry and standard differential scanning calorimetry (DSC). Using quasi‐isothermal TMDSC, the apparent reversing and nonreversing heat capacities were determined from 220 to 540 K, including glass and melting transitions. Truly reversible and time‐dependent irreversible heat effects were separated. The extrapolated vibrational heat capacity of the solid and the total heat capacity of the liquid served as baselines for the analysis. As one approaches the melting region from lower temperature, semicrystalline PTT shows a reversing heat capacity, which is larger than that of the liquid, an observation that is common also for other polymers. This higher heat capacity is interpreted as a reversible surface or bulk melting and crystallization, which does not need to undergo molecular nucleation. Additional time‐dependent, reversing contributions, dominating at temperatures even closer to the melting peak, are linked to reorganization and recrystallization (annealing), while the major melting is fully irreversible (nonreversing contribution). © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 622–631, 2000     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. I. Samples crystallized from the glassy state

The melting behavior of poly(L ‐lactic acid) film crystallized from the glassy state, either isothermally or nonisothermally, was studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), differential scanning calorimetry (DSC), and temperature‐modulated differential scanning calorimetry (TMDSC). Up to three crystallization and two melting peaks were observed. It was concluded that these effects could largely be accounted for on the basis of a “melt‐recrystallization” mechanism. When molecular weight is low, two melting endotherms are readily observed. But, without TMDSC, the double melting phenomena of high molecular weight PLLA is often masked by an exotherm just prior to the final melting, as metastable crystals undergo melt‐recrystallization during heating in the DSC. The appearance of a double cold‐crystallization peak during the DSC heating scan of amorphous PLLA film is the net effect of cold crystallization and melt‐recrystallization of metastable crystals formed during the initial cold crystallization. Samples cold‐crystallized at 80 and 90 °C did not exhibit a long period, although substantial crystallinity developed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3200–3214, 2006     

Thermal and dynamic mechanical properties of PES/PPS blends

Blends of poly(ether-sulfone) (PES) and poly(phenylene sulfide) (PPS) with various compositions were prepared using an internal mixer at 290°C and 50 rpm for 10 min. The thermal and dynamic mechanical properties of PES/PPS blends have been investigated by means of DSC and DMA. The blends showed two glass transition temperatures corresponding to PPS-rich and PES-rich phases. Both of them decreased obviously for the blends with PES matrix. On the other hand, T_g of PPS and PES phase decreased a little when PPS is the continuous phase. In the blends quenched from molten state the cold crystallization temperature of PPS was detected in the blends of PES/PPS with mass ratio 50/50 and 60/40. The melting point, crystallization temperature and the crystallinity of blended PPS were nearly unaffected when the mass ratio of PES was less than 60%, however, when the amount of PES is over 60% in the blends, the crystallization of PPS chains was hindered. The thermal and the dynamic mechanical properties of the PPS/PES blends were mainly controlled by the continued phase. This revised version was published online in August 2006 with corrections to the Cover Date.     

TMDSC analysis of single-site copolymer blends after thermal fractionation

Temperature-modulated differential scanning calorimetry (TMDSC) has been used to study the melting of a series of blends containing linear low-density polyethylene (LLDPE) and very low-density polyethylenes (VLDPE) with long chain branches. After the blends were subjected to different thermal histories including thermal fractionation by stepwise isothermal cooling, they were examined by TMDSC. TMDSC curves have been interpreted in terms of a combination of the reversing and non-reversing specific heats that result from reversible and irreversible events at the time and temperature, which they are detected, respectively. It was found that crystals formed at different crystallisation conditions had different internal order; hence they showed different amounts of reversing and non-reversing contributions. There is no exothermic activity seen in the non-reversing signal for the thermally fractionated polymers and their blends suggesting formation of crystals approaching equilibrium. In contrast, polymers and blends cooled at 10°C min^-1 cooling rate showed large exothermic contributions corresponding to irreversible effects. In addition, a true reversible melting contribution is also detected for both fast-cooled and thermally-fractionated samples during the quasi-isothermal measurements. This revised version was published online in July 2006 with corrections to the Cover Date.     

DSC Studies of Thermally Induced Phase Separation of Hydrogen Bonded Polymer Blends

The thermally induced phase separation behavior of hydrogen bonded polymer blends, poly(n-hexyl methacrylate) (PHMA) blended with poly(styrene-co-vinyl phenol) (STVPh) random copolymers having various vinyl phenol contents, was studied by temperature modulated differential scanning calorimetry (TMDSC).The enthalpy of phase separation was determined to be about 0.5 cal g^–1 for one of the blends. A phase diagram was constructed from the TMDSC data for one of the blends. The kinetics of phase separation was studied by determining the phase compositions from the glass transition temperatures of quenched samples after phase separation. Subsequently, the phase separated samples were annealed at temperatures below the phase boundary to observe the return to the homogeneous state.This revised version was published online in November 2005 with corrections to the Cover Date.     

Miscible blends prepared from two crystalline polymers

Differential scanning calorimetry was used to determine the miscibility behavior of several polyester/Saran blends, the two polymers forming these blends being semicrystalline. It was found that Saran is miscible with polycaprolactone (PCL), polyvalerolactone, poly(butylene adipate), and poly(hexamethylene sebacate) since a single glass transition temperature T_g was observed at each composition. However, immiscibility was found between Saran and poly(ethylene adipate), poly-(ethylene succinate), poly(β-propiolactone), and poly(α-methyl-α-n-propyl-β-propiolactone) since two T_g's were recorded at several compositions. Blends were then obtained containing, over a wide range of composition, a miscible amorphous phase and two different types of crystals. From melting-point depression data on PCL and Saran crystals, thermodynamic interaction parameters χ were calculated and found to be different for PCL-rich blends and for Saran-rich blends. This result suggests a variation of χ with composition. Saran is a polymer which does not contain α-hydrogens and its miscibility with polyesters may result from a β-hydrogen bonding interaction or a C?O/C? Cl dipole-dipole interaction.     

Poly(N-phenyl-2-hydroxytrimethylene amine): Its blends with poly(ϵ-caprolactone) and water-soluble polyethers

A new polymer with pendant hydroxyl groups, namely, poly(N-phenyl-2-hydroxytrime-thylene amine) (PHA), was synthesized by a direct condensation polymerization of aniline and epichlorohydrin in an alkaline medium. The new polymer is amorphous with a glass transition temperature (T_g) of 70°C. Blends of PHA with poly(ϵ-caprolactone) (PCL), as well as with two water-soluble polyethers, poly(ethylene oxide) (PEO) and poly(vinyl methyl ether) (PVME), were prepared by casting from a common solvent. It was found that all the three blends were miscible and showed a single, composition dependent glass transition temperature (T_g). FTIR studies revealed that PHA can form hydrogen bonds with PCL, PEO, and PVME, which are driving forces for the miscibility of the blends. © 1997 John Wiley & Sons, Inc.     

Temperature modulated dynamic mechanical analysis

Temperature modulated dynamic mechanical analysis (TMDMA) was performed in the same way as temperature modulated DSC (TMDSC) measurements. Temperature modulation with amplitude 0.5 K and period 20 min was realised by a series of linear heating and cooling cycles (saw-tooth modulation). As in TMDSC TMDMA allows for the investigation of reversible and non-reversible phenomena in the melting and crystallisation region of polymers. The advantage of TMDMA compared to TMDSC is the high sensitivity for small and slow changes in crystallinity, e.g. during re-crystallisation. The combination of TMDMA and TMDSC yields new information about local processes at the surface of polymer crystallites. It is shown that during and after isothermal crystallisation the surface of the individual crystallites is in equilibrium with the surrounding melt.     

Thermal memory of poly(3‐hydroxybutyrate) using temperature‐modulated differential scanning calorimetry

The influence of thermal history on morphology, melting, and crystallization behavior of bacterial poly(3‐hydroxybutyrate) (PHB) has been investigated using temperature‐modulated DSC (TMDSC), wide‐angle X‐ray diffraction (WAXRD) and polarized optical microscopy (POM). Various thermal histories were imparted by crystallization with continuous and different modulated cooling programs that involved isoscan and cool–heat segments. The subsequent melting behavior revealed that PHB experienced secondary crystallization during heating and the extent of secondary crystallization varied with the cooling treatment. PHB crystallized under slow, continuous, and moderate cooling rates were found to exhibit double melting behavior due to melting of TMDSC scan‐induced secondary crystals. PHB underwent considerable secondary crystallization/annealing that took place under modulated cooling conditions. The overall melting behavior was interpreted in terms of recrystallization and/or annealing of crystals. Interestingly, the PHB analyzed by temperature modulation programs showed a broad exotherm before the melting peak in the nonreversing heat capacity curve and a multiple melting reversing curve, verifying that the melting–recrystallization and remelting process was operative. WAXRD and POM studies supported the correlations from DSC and TMDSC results. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 70–78, 2006     

Isothermal crystallisation kinetics of poly(3-hydroxybutyrate) using step-scan DSC

The crystallisation kinetics, melting behaviour and morphology, of bacterial poly(3-hydoxybutyrate) (PHB) have been investigated by using differential scanning calorimetry (DSC), step-scan DSC (SDSC), wide angle X-ray diffraction (WAXRD) and hot stage polarised optical microscopy (HSPOM). DSC imparted isothermal crystallisation thermal history. The subsequent melting behaviour revealed that all PHB materials experienced secondary crystallisation during heating and the extent of secondary crystallisation varied depending on the crystallisation temperature. PHB samples were found to exhibit double melting behaviour due to melting of SDSC scan-induced secondary crystals, while considerable secondary crystallisation or annealing took place under the modulated heating conditions. The overall melting behaviour was rationalised in terms of recrystallisation and/or annealing of crystals. Interestingly, the PHB materials analysed by SDSC showed a broad exotherm before the melting peak in the non-reversing curve and a multiple melting peak reversing curve, verifying that the melting-recrystallisation and remelting process was operative. HSOM studies supported the conclusions from DSC that the radial growth rate of the PHB spherulites was significantly varied upon the crystallisation conditions. One form of crystals was shown by WAXRD from isothermally crystallised PHB.     

Miscibility in a ternary system of poly(ether imide) with semicrystalline poly(ethylene terephthalate) and poly(butylene terephthalate)

A rare case of thermodynamic miscibility has been demonstrated in the amorphous state (quenched glass as well as molten state) of a ternary blend system formed by poly(ether imide) and semicrystalline poly(ethylene terephthalate) and poly-(butylene terephthalate). A single glass transition temperature (T_g) in the ternary blends was observed using differential scanning calorimetry and dynamic mechanical analysis.