Effect of anionic surfactant and short-chain alcohol mixtures on adsorption at quartz/water and water/air interfaces and the wettability of quartz

Measurements of the advancing contact angles for aqueous solutions of sodium dodecyl sulfate (SDDS) or sodium hexadecyl sulfonate (SHS) in mixtures with methanol, ethanol, or propanol on a quartz surface were carried out. On the basis of the obtained results and Young and Gibbs equations the critical surface tension of quartz wetting, the composition of the surface layer at the quartz-water interface, and the activity coefficients of the anionic surfactants and alcohols in this layer as well as the work of adhesion of aqueous solutions of anionic surfactant and alcohol mixtures to the quartz surface were determined. The analysis of the contact angle data showed that the wettability of quartz changed visibly only in the range of alcohol and anionic surfactant concentration at which these surface-active agents were present in the solution in the monomeric form. The analysis also showed that there was a linear dependence between the adhesion and the surface tension of aqueous solutions of anionic surfactant and alcohol mixtures. This dependence can be described by linear equations for which the constants depend on the anionic surfactant and alcohol concentrations. The slope of all linear dependence between adhesion and surface tension was positive. The critical surface tension of quartz wetting determined from this dependence by extrapolating the adhesion tension to the value equal to the surface tension (for contact angle equal zero) depends on the assumption whether the concentration of anionic surfactant or alcohol was constant. Its average value is equal to 29.95mN/m and it is considerably lower than the quartz surface tension. The positive slope of the adhesion-surface tension curves was explained by the possibility of the presence of liquid vapor film beyond the solution drop which settled on the quartz surface and the adsorption of surface-active agents at the quartz/monolayer water film-water interface. This conclusion was confirmed by the work of adhesion of aqueous solutions of anionic surfactants and short-chain alcohol mixtures to the quartz surface determined on the basis of the contact angle data and molar fraction of anionic surfactants and alcohols and their activity coefficient in the surface layer.     

Influence of 1-decanol on the surface tension and wetting power of a new anionic surfactant derived from sugar

We studied the adsorption behaviour at the liquid/air and liquid/solid interface of a new anionic surfactant derived from sugar, the sodium decyl galacturonate. The surface tension of aqueous solutions, measured in equilibrium and as a function of time, is particularly affected by the presence of decanol, synthesis residue, which amount ranges between about 0 and 13%. The surface tension lowering is accelerated in presence of decanol, owing to its rapid diffusion to the interface or/and because it affects the mobility and adsorption process of the anionic surfactant molecules. The wetting power of surfactant solutions were also investigated in relation with textile treatment applications. We measured the kinetics of absorption of surfactant solutions in a piece of standard cotton and compared it to the absorption of pure decanol, a completely wetting liquid and to the absorption of an alkylpolyglucoside. The time at which the fabric piece is saturated appears to be related to the adsorption of surface-active molecules on the fibers at the advancing liquid front/fabric contact line. Decanol was found to promote absorption and micellar life-time seem to reflect the differences observed at high concentration. This study shows the importance of controlling the amount of surface-active residues which may alter the kinetics of surfactant adsorption, particularly in industrial processes where equilibrium conditions are not reached.     

Effect of sodium dodecyl sulfate and cetyltrimethylammonium bromide catanionic surfactant on the enzymatic hydrolysis of Avicel and corn stover

Nonionic surfactants could effectively improve the enzymatic hydrolysis efficiency of lignocellulose, while small molecule anionic and cationic surfactants usually inhibited the enzymatic hydrolysis. The results showed that the anionic surfactant sodium dodecyl sulfate (SDS) could improve the enzymatic hydrolysis efficiency of Avicel at the concentration range of 0.1–1 mM, but it did inhibit enzymatic hydrolysis at higher concentration. Cationic surfactant cetyltrimethylammonium bromide (CTAB) was used to regulate the surface charge of SDS; thereby catanionic surfactant SDS-CTAB was formed. The effect of SDS-CTAB catanionic surfactant with varied molar ratios on the enzymatic hydrolysis of pure cellulose and corn stover at various enzymatic hydrolysis environments was investigated. SDS-CTAB could increase the enzymatic hydrolysis of corn stover at high solid loading from 33.3 to 42.4%. Using SDS-CTAB could reduce about 58% of the cellulase dosage to achieve 80% of the enzymatic hydrolysis of corn stover. SDS-CTAB catanionic surfactant could regulate the surface charge of cellulase in the hydrolyzate and reduce the non-productive adsorption of cellulase on the lignin, thereby improving the enzymatic hydrolysis efficiency of lignocellulose.     

The Dispersion Properties of Precipitated Calcium Carbonate Suspensions Adsorbed with Alkyl Polyglycoside in Aqueous Medium

The zeta potentials and dispersion properties of precipitated calcium carbonate suspensions adsorbed with alkyl polyglycosides in aqueous medium were investigated. Within the investigated pH ranges, the adsorption curves of alkyl polyglycosides on calcium carbonates show sigmoidal shapes, and the zeta potential decreases as the amount of adsorption increases. At positively charged surfaces of low pH, the adsorption amounts were greater than those at negatively charged surfaces, indicating that alkyl polyglycosides were negatively charged in aqueous solutions. At low concentrations of alkyl polyglycosides, the dispersion stabilities of suspensions were very poor and showed no linearity with zeta potentials over the entire range of pHs, which may be attributed to the onset of hydrophobic interaction between particles due to the adsorption of surfactant molecules. This destabilization continued until monolayer coverage by the surfactant layer was complete. Based on the classical DLVO theory, there may be a strong hydrophobic interaction between particles. Beyond monolayer adsorption, the dispersion stability increases, probably by the formation of hemimicelle or admicelle. Therefore, it is believed that ionization of alkyl polyglycosides and admicelles of surfactants on particle surface plays a key role in the stability of dispersions and the abrupt increase in adsorption. Copyright 2000 Academic Press.     

Chemisorption of phosphoric acid and surface characterization of As passivated AlN powder against hydrolysis

By simply refluxing a commercial AlN powder in a mixture solution of ethanol, H(3)PO(4), and Al(H(2)PO(4))(3) for 24 h at 80 degrees C, the powder was successfully passivated against hydrolysis. The phosphate layer formed on the surface of AlN powder was found to be quite stable toward protecting the powder from hydrolysis. The efficacy of the coating was established by suspending the treated and the untreated powders in water for 72 h and subsequently characterizing them by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and Raman analysis. The good dispersing behavior of the treated AlN powder in water was confirmed by the low viscosity of an AlN suspension containing 50 vol % solids demonstrating the viability of replacing organic solvents by water in colloidal processing of AlN-based ceramics.     

A review on experimental studies of surfactant adsorption at the hydrophilic solid-water interface

The progresses of understanding of the surfactant adsorption at the hydrophilic solid-liquid interface from extensive experimental studies are reviewed here. In this respect the kinetic and equilibrium studies involves anionic, cationic, non-ionic and mixed surfactants at the solid surface from the solution. Kinetics and equilibrium adsorption of surfactants at the solid-liquid interface depend on the nature of surfactants and the nature of the solid surface. Studies have been reported on adsorption kinetics at the solid-liquid interface primarily on the adsorption of non-ionic surfactant on silica and limited studies on cationic surfactant on silica and anionic surfactant on cotton and cellulose. The typical isotherm of surfactants in general, can be subdivided into four regions. Four-regime isotherm was mainly observed for adsorption of ionic surfactant on oppositely charged solid surface and adsorption of non-ionic surfactant on silica surface. Region IV of the adsorption isotherm is commonly a plateau region above the CMC, it may also show a maximum above the CMC. Isotherms of four different regions are discussed in detail. Influences of different parameters such as molecular structure, temperature, salt concentration that are very important in surfactant adsorption are reviewed here. Atomic force microscopy study of different surfactants show the self-assembly and mechanism of adsorption at the solid-liquid interface. Adsorption behaviour and mechanism of different mixed surfactant systems such as anionic-cationic, anionic-non-ionic and cationic-non-ionic are reviewed. Mixture of surface-active materials can show synergistic interactions, which can be manifested as enhanced surface activity, spreading, foaming, detergency and many other phenomena.     

新疆褐煤疏水改性提高其成浆性能

针对新疆褐煤具有较高内水的问题,制备了阴离子AKD改性剂和非离子AKD改性剂,对褐煤颗粒进行疏水改性。研究了改性前后煤粒表面化学成分、孔隙分布、亲疏水性和Zeta电位等煤粒表面特性,并结合NSF分散剂在改性前后煤粒表面吸附量大小,探讨了改性前后褐煤水煤浆的成浆性、流变性和稳定性。结果表明,改性后煤粒孔隙结构降低,煤粒表面碳的相对含量增加,氧的相对含量降低,煤水界面接触角增加,煤粒疏水性能增强。NSF分散剂在改性煤表面吸附量增加,煤粒表面负电性增强。由阴离子AKD改性煤、非离子AKD改性煤制备的水煤浆最大成浆质量分数从原煤56.6%分别增加至61.0%、62.5%,浆体析水率从原煤13.97%分别降低至7.45%、7.89%,同时改性后煤粒制备的浆体均表现出剪切变稀的假塑性流体。因此,改性煤粒更容易制备高浓度、低黏度、高稳定性且易于储存和运输的水煤浆。     

Dispersion stability of a ceramic glaze achieved through ionic surfactant adsorption

The adsorption of cetylpyridinium chloride (CPC) and sodium dodecylbenzenesulfonate (SDBS) onto a ceramic glaze mixture composed of limestone, feldspar, quartz, and kaolin has been investigated. Both adsorption isotherms and the average particle zeta potential have been studied in order to understand the suspension stability as a function of pH, ionic strength, and surfactant concentration. The adsorption of small amounts of cationic CPC onto the primarily negatively charged surfaces of the particles at pH 7 and 9 results in strong attraction and flocculation due to hydrophobic interactions. At higher surfactant concentrations a zeta potential of more than +60 mV results from the bilayered adsorbed surfactant, providing stability at salt concentrations < or = 0.01 M. At 0.1 M salt poor stability results despite substantial zeta potential values. Three mechanisms for SDBS adsorption have been identified. When anionic SDBS monomers either adsorb by electrostatic interactions with the few positive surface sites at high pH or adsorb onto like charged negative surface sites due to dispersion or hydrophobic interactions, the magnitude of the negative zeta potential increases slightly. At pH 9 this increase is enough to promote stability with an average zeta potential of more than -55 mV, whereas at pH 7 the zeta potential is lower at about -45 mV. The stability of suspensions at pH 7 is additionally due to steric repulsion caused by the adsorption of thick layers of neutrally charged Ca(DBS)2 complexes created when the surfactant interacts with dissolved calcium ions from the calcium carbonate component.     

Control of surfactant level in starve-fed emulsion polymerization. I. Sulfate-containing oligomers: Preparation and application as surfactant in emulsion polymerization

It is well known that the amount of surfactant must be carefully controlled during starve-fed emulsion polymerization processes. Too little surfactant leads to emulsion instability and coagulation, while too much surfactant leads to secondary particle formation. Although these relationships are qualitatively understood in the art, there is little quantitative basis to guide the synthetic chemist, especially in multistep starve-fed emulsion polymerization processes to make larger supermicron particles. We have developed a method, which will be described in a companion article, to control the surfactant level by monitoring the surface tension during polymerization. In order to quantitatively predict how much surfactant to add at any given time, one needs to know in advance the adsorption characteristics of the soap. Further complicating the matter is the formation of “in situ” or oligomeric surfactant during polymerization with aqueous initiators such as ammonium persulfate. This work demonstrates how to prepare surface-active oligomers and how to make latex particles using them as surfactant. First, we established the mass balance for the initiator-derived sulfate groups in seed latexes by conductometric, potentiometric, and iodometric titrations. Based on the characterization of seed latexes, a method for determining the effective sulfate concentration has been developed. When surface-active oligomers were used as the only surfactant, we obtained a series of monodisperse, supermicron copolymer latex particles with diameters up to 3.22 μm. This is a similar result to that obtained with a commercially made anionic surfactant. © 1995 John Wiley & Sons, Inc.     

Interfacial and micellar properties of some anionic/cationic binary surfactant systems. 1. Surface properties and prediction of surface tension

The surface tension equations of binary surfactant mixtures are established by combining the Szyszkowski equation for pure surfactant solutions and extended nonideal theory for mixed adsorption. They are then successfully applied to two relatively long-chain anionic/cationic binary surfactant systems: triethanolammonium dodecylpoly(oxyethylene)sulfate, as an anionic species (containing about 2 ethylene oxide units), mixed with dodecyltrimethylammonium bromide or hexadecyltrimethylammonium bromide. The composition of the mixed monolayer is mixing-ratio dependent and is slightly asymmetric: for overall equimolar mixtures, the larger mole fraction in the mixed monolayer is that of the more surface-active ion. The strong synergetic effects observed in the surface tension reduction efficiency are reflected by large negative β^s parameters, according to regular solution theory. They can be interpreted by the more negative adsorption free energy of each surfactant and the smaller area occupied by surfactant hydrocarbon chains in the mixed monolayer. Received: 20 April 1998 /Accepted in revised form: 27 August 1999     

Effect of polyelectrolytes and polyelectrolyte mixtures on the electrokinetic potential of dispersed particles. 1. Electrokinetic potential of polystyrene particles in solutions of surfactants, polyelectrolytes and their mixtures

The effect of cationic and anionic surfactants, as well as cationic and anionic polyelectrolytes (PE), their binary mixtures on the electrokinetic potential of monodisperse carboxylated polystyrene (PS) particles as a function of the reagents dose, pH, the charge density (CD) of polymers, the surfactant/PE and binary PE mixture composition, and sequence of components addition to the suspension has been studied. It has been shown that addition of increasing amount of anionic surfactant/polyelectrolytes increases the absolute value of the negative zeta-potential of PS particles; this increase is stronger the CD of the PE and pH of the system are higher. Adsorption of cationic surfactant/polyelectrolytes leads to a significant decrease in the negative ζ-potential and to overcharging the particles; changes in the ζ-potential are more pronounced for PE samples with higher CD and for suspensions with lower pH values. In mixtures of cationic and anionic PE, in a wide range of mixture composition, the ζ-potential of particles is determined by the adsorbed amount of the anionic polymer independently of the CD of PEs and the sequence of addition of the mixture components. The isoelectric point of the surface is reached at the adsorbed amount of positive charges of PE that is approximately equal to the surface CD of particles. The laws observed were explained by features of macromolecules conformation in adsorbed mixed PE layers. Considerations about the role of coulombic and non-coulombic forces in the mechanism of anionic/cationic PE adsorption are presented.     

Assessment of the Surface Heterogeneity of Talc Materials

The hydrophobic and hydrophilic components of the surface of talc materials in aqueous solution were determined using ionic surfactants and their polar headgroup adsorption isotherms. The hydrophilic and hydrophobic surface areas are inferred from the amount of probe molecule adsorbed and the structure of the adsorbed layer. Natural dispersion of talc shows at 298 K a pH of 9.4 and the electrophoretic measurements indicate that the particles are negatively charged. The hydrophilic surface area is estimated from the adsorption of benzyltrimethylammonium ions (BTMA(+)) through electrostatic interactions as supported by the increase of divalent ions in the bulk phase and the decrease in the exothermic displacement enthalpy. It was also observed from the adsorption isotherm of benzene sulfonate anions that the density of positive surface sites is very low and is thus neglected. The adsorption of an anionic surfactant essentially occurs through dispersive interactions between the nonpolar organic tail of the molecule and the hydrophobic surface. Furthermore, some assumptions on the structure of dodecyl sulfate surfactant aggregates at the interface allow the hydrophobic part of the talc particles to be estimated. The cationic surfactant adsorption has been investigated and found to corroborate the hydrophilic and hydrophobic area values first obtained. Copyright 2001 Academic Press.     

Adsorption of sodium dodecylsulfate on modified carbon adsorbents

The adsorption of anionic surfactants on carbon adsorbents modified with water-soluble derivatives of natural polymers, cellulose and chitin, is considered with sodium dodecylsulfate taken as an example. It is shown that such modification leads to changes in the adsorption structural characteristics and the particle size distribution of carbon-water suspensions of the original adsorbent, and to the emergence of new functional groups on its surface that are able to interact selectively with adsorbate molecules. It is assumed that adsorption of anionic surfactant on carbon adsorbents under equilibrium conditions proceeds via stepwise filling of the carbon??s porous structure: we first observe volume filling of micropores according to their sizes, and then the formation of a surfactant??s monolayer in mesopores and on the outer surface of the adsorbate. It is established by thermal analysis that the thermal stability of carbon adsorbents is enhanced through the preferential localization of anionic surfactants in micropores. The filling of mesopores and the outer carbon surface by surfactant molecules leads to a regular decrease in thermal stability and an increase in the adsorbent surface??s hydrophilicity.     

The influence of stabilizing agents on the interaction between styrene/butadiene latex and calcium carbonate: a calorimetric and a dynamic electrokinetic study

The role of stabilizing agents in the interaction between styrene/butadiene latex and calcium carbonate particles has been studied using isothermal titration calorimetry (ITC) and an electrokinetic sonic amplitude (ESA) technique. It is demonstrated that the polyacrylate sodium salt (dispersing agent, referred to as NaPA) used as stabilizing agent for the calcium carbonate suspensions principally affects the interfacial properties of the calcite surface. An electrostatic barrier is created and this decreases the attractive interactions between the latex and the negatively charged mineral surface. The total enthalpy change observed when an emulsion of styrene/butadiene particles substantially free from surfactant was added to the dispersed calcium carbonate could be described via a relatively complex path. The process included (i) an exothermic response from the association of the latex particles (adsorption process) with the dispersed calcium carbonate surface and (ii) an endothermic bulk phase effect due to the adsorption on the latex particles of dissolved species originating from the calcium carbonate. Stabilization of the latex particles with sodium dodecyl benzene sulfonate (SDBS) or a non-ionic fatty alcohol ethoxylate surfactant did not significantly change the enthalpy of interaction. It was further demonstrated that SDBS had a very weak affinity for the dispersed calcium carbonate particles and that dissolution of species, such as calcium ions, from the calcium carbonate surface, allows further adsorption of SDBS onto the latex particles.     

Adsorption of anionic surfactants on positively charged polystyrene particles II

In the case of cationic polystyrene latex, the adsorption of anionic surfactants involves a strong electrostatic interaction between both the particle and the surfactant, which may affect the conformation of the surfactant molecules adsorbed onto the latex-particle surface. The adsorption isotherms showed that adsorption takes place according to two different mechanisms. First, the initial adsorption of the anionic surfactant molecules on cationic polystyrene surface would be due to the attractive electrostatic interaction between both ionic groups, laying the alkyl-chains of surfactant molecules flat on the surface as a consequence of the hydrophobic interaction between these chains and the polystyrene particle surface, which is predominantly hydrophobic. Second, at higher surface coverage the adsorbed surfactant molecules may move into a partly vertical orientation with some head groups facing the solution. According to this second mechanism the hydrophobic interactions of hydrocarbon chains play an important role in the adsorption of surfactant molecules at high surface coverage. This would account for the very high negative mobilities obtained at surfactant concentration higher than 5×10^–7 M. Under high surface-coverage conditions, some electrophoretic mobility measurements were performed at different ionic strength. The appearance of a maximum in the mobility-ionic strength curves seems to depend upon alkyl-chain length. Also the effects of temperature and pH on mobilities of anionic surfactant-cationic latex particles have been studied. The mobility of the particles covered by alkyl-sulphonate surfactants varied with the pH in a similar manner as it does with negatively charged sulphated latex particles, which indicates that the surfactant now controls the surface charge and the hydrophobic-hydrophilic character of the surface.Dedicated to the memory of Dr. Safwan Al-Khouri IbrahimPresented at the Euchem Workshop on Adsorption of Surfactants and Macromolecules from Solution, Åbo (Turku), Finland, June 1989     

Protecting nanoscaled non-oxidic particles from oxygen uptake by coating with nitrogen-containing surfactants

To suppress the reactivity of nanoscaled non-oxidic powders of titanium nitride (TiN) and silicon carbonitride (SiCN) against hydrolysis and oxidation, chemical surface modification with nitrogen-containing surfactants was investigated. Among these surfactants, long-chain primary amines, ethylenediamines, guanidines, nitriles, isocyanates, and succinimides were examined. Thermogravimetry, elemental analysis, and behavior against the water-vapor adsorption of the modified particles were used as methods to estimate the protective capacity of the organic coating material. The best results were obtained by using the long-chain amines and octadecylisocyanate, which were indicated by a significant shift of the powder oxidation toward the higher temperatures and an increase of the particle hydrophobicity. A long-chain succinimide was found to be the most effective in dispersing nanoscaled TiN in organic media. Preparation of a stable aqueous dispersion without significant changes in the elemental composition of the powder was achieved by the application of an ionic surfactant to the surface-modified particles.     

Adsorption/aggregation of surfactants and their mixtures at solid-liquid interfaces

Adsorption of surfactants and polymers at solid-liquid interfaces is used widely to modify interfacial properties in a variety of industrial processes such as flotation, ceramic processing, flocculation/dispersion, personal care product formulation and enhanced oil recovery. The behavior of surfactants and polymers at interfaces is determined by a number of forces, including electrostatic attraction, covalent bonding, hydrogen bonding, hydrophobic bonding, and solvation and desolvation of various species. The extent and type of the forces involved varies depending on the adsorbate and the adsorbent, and also the composition and other characteristics of the solvent and dissolved components in it. The influence of such forces on the adsorption behavior is reviewed here from a thermodynamics point of view. The experimental results from microcalorimetric and spectroscopic studies of adsorbed layers of different surfactant and polymer systems at solid-liquid interfaces are also presented. Calorimetric data from the adsorption of an anionic surfactant, sodium octylbenzenesulfonate, and a non-ionic surfactant, dodecyloxyheptaethoxyethylalcohol, and their mixtures on alumina, yielded important thermodynamic information. It was found that the adsorption of anionic surfactants alone on alumina was initially highly exothermic due to the electrostatic interaction with the substrate. Further adsorption leading to a solloid (hemimicelle) formation is proposed to be mainly an entropy-driven process. The entropy effect was found to be more pronounced for the adsorption of anionic-non-ionic surfactant mixtures than for the anionic surfactant alone. Fluorescence studies using a pyrene probe on an adsorbed surfactant and polymer layers, along with electron spin resonance (ESR) spectroscopy, reveal the role of surface aggregation and the conformation of the adsorbed molecules in controlling the dispersion and wettability of the system.     

Kinetics of sodium dodecyl benzene sulfonate adsorption on hematite and its interaction with polyacrylamide

This article describes the adsorption of sodium dodecyl benzene sulfonate, an anionic surfactant, on a hematite surface and that when the surface is preadsorbed with polyacrylamide. The adsorption of surfactant on a hematite surface has been studied through equilibration and during kinetics measurements at three pH levels, viz. 4.0, 7.0, 8.9. The surfactant adsorbs strongly on the hematite surface. The adsorption density at equilibrium as well as the rate of adsorption are dependent on the suspension pH. The maximum adsorption density has been observed at pH 4, which reflects strong adsorption of negatively charged sulfonate ions on the oppositely charged Fe₂O₃ surface (point of zero charge, 6.4). The adsorption density reaches its equilibrium value sooner in the case of an alkaline suspension and later in the case of acidic pH. The polymer surfactant interaction has been noticed in the present study and is also a function of pH. The hematite mineral when preadsorbed with the polymer draws fewer of the surfactant molecules at lower surface coverage (during the initial period of the kinetics measurement) irrespective of the pH. When the adsorption of the surfactant reaches a value which is near the equilibrium one, the pH effect is evident. In the case of acidic pH, the surfactant adsorbs more on the hematite surface when preadsorbed with the polymer compared to the bare surface. In the case of neutral or alkaline pH, however, the density of surfactant adsorption remains lower throughout the kinetics measurement when the surface is preadsorbed with the flocculant compared to the bare surface. The particles also remain flocculated till the end of the experiment, whereas at pH 4 the particles are deflocculated. In addition to pH, the electrostatic nature of the adsorbent and the presence of anionic surfactant have an influence on the flocculation–deflocculation phenomena. The polymer–surfactant interaction has been schematically represented. The surfactant is bound with polymeric chains as a combination of its monomeric form as well as in the form of association in the case of acidic media and in competition with polymer in the case of alkaline media. Received: 18 April 2000/Accepted: 2 August 2000     

Multiple phase inversion of emulsions stabilized by in situ surface activation of CaCO3 nanoparticles via adsorption of fatty acids

The in situ surface activation of raw CaCO(3) nanoparticles by interaction with a series of sodium carboxylates of chain length between 6 and 12 as well as sodium 2-ethylhexylsulfosuccinate (AOT) was studied, and the impact of this on the stabilization and phase inversion of toluene-water emulsions was assessed. By using complementary experiments including measurement of particle zeta potentials, adsorption isotherms of amphiphile, and relevant contact angles, the mechanism of this activation was revealed. The results show that hydrophilic CaCO(3) nanoparticles can be surface activated by interaction with sodium carboxylates and AOT even if they are not surface-active themselves. Both the electrostatic interaction between the positive charges on particle surfaces and the negative charges of anionic amphiphile headgroups and the chain-chain interactions of the amphiphile result in monolayer adsorption of the amphiphile at the particle-water interface. This transforms the particles from hydrophilic to partially hydrophobic such that they become surface-active and stabilize oil-in-water O/W(1) emulsions and induce O/W(1) → water-in-oil W/O phase inversion, depending on the chain length of the carboxylate molecules. At high amphiphile concentration, bilayer or hemimicelle adsorption may occur at the particle-water surface, rendering particles hydrophilic again and causing their desorption from the oil-water interface. A second phase inversion, W/O → O/W(2), may occur depending on the surface activity of the amphiphile. CaCO(3) nanoparticles can therefore be made good stabilizers of both O/W and W/O emulsions once surface activated by mixing with traces of suitable anionic amphiphile.     

Adsorption behavior of hydrophobin and hydrophobin/surfactant mixtures at the solid-solution interface

The adsorption of surface-active protein hydrophobin, HFBII, and HFBII/surfactant mixtures at the solid-solution interface has been studied by neutron reflectivity, NR. At the hydrophilic silicon surface, HFBII adsorbs reversibly in the form of a bilayer at the interface. HFBII adsorption dominates the coadsorption of HFBII with cationic and anionic surfactants hexadecyltrimethyl ammonium bromide, CTAB, and sodium dodecyl sulfate, SDS, at concentrations below the critical micellar concentration, cmc, of conventional cosurfactants. For surfactant concentrations above the cmc, HFBII/surfactant solution complex formation dominates and there is little HFBII adsorption. Above the cmc, CTAB replaces HFBII at the interface, but for SDS, there is no affinity for the anionic silicon surface hence there is no resultant adsorption. HFBII adsorbs onto a hydrophobic surface (established by an octadecyl trimethyl silane, OTS, layer on silicon) irreversibly as a monolayer, similar to what is observed at the air-water interface but with a different orientation at the interface. Below the cmc, SDS and CTAB have little impact upon the adsorbed layer of HFBII. For concentrations above the cmc, conventional surfactants (CTAB and SDS) displace most of the HFBII at the interface. For nonionic surfactant C(12)E(6), the pattern of adsorption is slightly different, and although some coadsorption at the interface takes place, C(12)E(6) has little impact on the HFBII adsorption.