The effect of the addition of carbon black and the increase in film thickness on the sensing layers of ZnO / ZnFe2O4 in polymer thick film gas sensors

The aim of this work is to investigate the effect of increasing the carbon black and the sensing layer thickness on the response of a sensor. Three sensors of 60/40 mol% ZnO/Fe₂O₃ with different percentages of carbon black (1.5, 2 and 2.5 wt%) were fabricated on alumina substrates and copper thin film electrodes. The base resistance of the 1.5 wt% carbon black sensor was while for the 2 wt% carbon black sensors it was . The lowest base resistance was recorded with the 2.5 wt% carbon black sensor to be . The sensors were used to detect propanol in the concentration range 2500–5000 ppm, increasing with a step size of 500 ppm, at room temperature. The responses of the sensors were determined as ((R_gas−R_air)/R_air)×100 while the sensitivity was calculated as the slope of the graphs. The sensitivity was increased as the amount of carbon black decreased. The sensitivities of the sensors to propanol at room temperature were 0.0105, 0.005 and 0.002%/ppm for the three sensors. On the other hand, four sensors have different thickness were fabricated used by the same manner. It was found that the response of the sensor increased relatively as the thicknesses of the sensing layer decreased. Results show that the one-layer sensor has the highest response, followed by a decrease in the responses for sensors with higher numbers of layers, 2, 3, 4 and 5 successively.     

Synthesis and magnetic properties of hard magnetic (CoFe2O4)-soft magnetic (Fe3O4) nano-composite ceramics by SPS technology

CoFe₂O₄/Fe₃O₄ nano-composite ceramics were synthesized by Spark Plasma Sintering. The X-ray diffraction patterns show that all samples are composed of CoFe₂O₄ and Fe₃O₄ phases when the sintering temperature is below 900 °C. It is found that the magnetic properties strongly depend on the sintering temperature. The two-step hysteresis loops for samples sintered below 500 °C are observed, but when sintering temperature reaches 500 °C, the step disappears, which indicates that the CoFe₂O₄ and Fe₃O₄ are well exchange coupled. As the sintering temperature increases from 500 to 800 °C, the results of X-ray diffractometer indicate the constriction of crystalline regions due to the ion diffusion at the interfaces of CoFe₂O₄/Fe₃O₄ phases, which have great impact on the magnetic properties.     

Synthesis and electrical properties of In2O3(ZnO)m superlattice nanobelt

One-dimensional（ID） In₂O₃（ZnO）_m superlattice nanobelts are synthesized by a chemical vapor deposition method.The formation of the In₂O₃（ZnO）_m superlattice is verified by the high-resolution transmission electron microscopy images.The typical zigzag boundaries could be clearly observed.An additional peak at 614 cm^-1 is found in the Raman spectrum,which may correspond to the superlattice structure.The study about the electrical transport properties reveals that the In₂O₃（ZnO）_m nanobelts exhibit peculiar nonlinear I-V characteristics even under the Ohmic contact measurement condition,which are different from the Ohmic behaviors of the In-doped ZnO nanobelts.The photoelectrical measurements show the differences in the photocurrent property between them,and their transport mechanisms are also discussed.     

Comparison of magnetic properties in LixCoO2 and its decomposition products LiCo2O4 and Co3O4

Thermal stability of cathode material in the charged state is an important aspect for the safety of rechargeable batteries. It is well known that layered Li_xCoO₂ decomposes to a mixture of LiCoO₂ and Co₃O₄ at elevated temperatures. However, not many experimental evidences exist on intermediate phases those may form during the decomposition. Using magnetic measurements we show that it is possible to distinguish between the spinels LiCo₂O₄ and Co₃O₄ and thereby follow the decomposition of Li_xCoO₂. We characterize the magnetic behavior of thermally aged Li_xCoO₂ (x = 0.98, 0.76, 0.55) with increasing annealing time. Our results reveal the appearance of magnetic ordering in the thermally degraded products. The detailed analysis illustrates that the formation of Co₃O₄ is preceded by the formation of a meta stable LiCo₂O₄ phase.     

Synthesis and performance of core-shell structured ZnO/In2O3 composites in situ growth

Core-shell structured ZnO/In₂O₃ composites were successfully synthesized via situ growth method. Phase structure, morphology, microstructure and property of the products were investigated by X-ray diffraction (XRD), TG-DTA, field emission scanning electron microscopy (FESEM), energy-dispersive spectrometry (EDS), transmission electron microscope (TEM) and photoluminescence (PL). Results show that the core-shell structures consist of spindle-like ZnO with about 800 nm in length and 200 nm in diameter, and In₂O₃ particles with a diameter of 50 nm coated on the surface of ZnO uniformly. HMTA plays an important role in the formation of core-shell structures and the addition of In₂O₃ has a great effect on PL spectrum. Possible mechanism for the formation of core-shell structures is also proposed in this paper.     

A facile synthesis of monodisperse CoFe2O4/SiO2 nanoparticles

Aminated-CoFe₂O₄/SiO₂ magnetic nanoparticles (NPs) were prepared from primary silica particles using modified StÖber method. By optimizing the preparation conditions, monodisperse CoFe₂O₄/SiO₂ NPs with high amino groups’ density were obtained, which is necessary for enzyme immobilization. TEM confirm that the sample is a core/shell structure. These aminated-CoFe₂O₄/SiO₂ NPs have narrow size distributions with a mean size of about 60 nm. Moreover, the aminated-CoFe₂O₄/SiO₂ NPs can be easily dispersed in aqueous medium. The experimental results also show that the NPs have superparamagnetism, indicating that the aminated-CoFe₂O₄/SiO₂ NPs can be used as an effective carrier for the enzyme immobilization.     

Characterization and electrochemical performance of the spinel LiMn2O4 prepared from -MnO2

The preparation and characterization of the spinel LiMn₂O₄ obtained by solid state reaction from quasi-amorphous -MnO₂ is reported. A well-defined highly pure spinel was characterized from X-ray diffractograms. The average manganese valence of -MnO₂ and spinel samples was found to be 3.89±0.01 and 3.59±0.01, respectively. The electrochemical performance of the spinel was evaluated through cyclic voltammetry and chronopotentiometry. The voltammetric profiles obtained at 1 mV/s for the LiMn₂O₄ electrode in 1 M LiClO₄ dissolved in a 2:1 mixture of ethylene carbonate and dimethyl carbonate showed typical peaks for the lithium insertion/extraction reactions. The charge capacity of this electrode was found to be 110 mA h g⁻¹ for the first charge/discharge cycles.     

Synthesis and characterization of thermoluminescent Li2B4O7 nanophosphor

Lithium borate (Li₂B₄O₇) is a low Z_eff, tissue equivalent material that is commonly used for medical dosimetry using the thermoluminescence (TL) technique. Nanocrystals of lithium borate were synthesized by the combustion method for the first time in the laboratory. TL characteristics of the synthesized material were studied and compared with those of commercially available microcrystalline Li₂B₄O₇. The optimum pre-irradiation annealing condition was found to be 300 °C for 10 min and that of post-irradiation annealing was 300 °C for 30 min. The synthesized Li₂B₄O₇ nanophosphor has very poor sensitivity for low doses of gamma up to 10¹ Gy whereas from 10¹ to 4.5×10² Gy this phosphor exhibits a linear response and then from 4.5×10² to 10³ Gy it shows supralinearity. Thermoluminescence properties of Li₂B₄O₇ nanophosphor doped with Cu has also been investigated in this paper. It shows low fading and a linear response over a wide range of gamma radiation from 1×10² to 5×10³ Gy. Therefore the synthesized lithium borate nanophosphor doped with Cu may be used for high dose measurements of gamma radiations.     

Direct micron-sized LiMn2O4 particle coating on LiCoO2 cathode material using surfactant

Micron-sized LiMn₂O₄ particles were easily coated on LiCoO₂ cathodes using an amphoteric gelatin surfactant at pH4–5. The coated LiCoO₂ material showed a significantly higher thermal stability during charging and capacity retention on cycling at 4.6 V, compared to the bare LiCoO₂.     

Immobilization of glucose oxidase using CoFe2O4/SiO2 nanoparticles as carrier

Aminated-CoFe₂O₄/SiO₂ magnetic nanoparticles (NPs) were prepared from primary silica particles using modified StÖber method. Glucose oxidase (GOD) was immobilized on CoFe₂O₄/SiO₂ NPs via cross-linking with glutaraldehyde (GA). The optimal immobilization condition was achieved with 1% (v/v) GA, cross-linking time of 3 h, solution pH of 7.0 and 0.4 mg GOD (in 3.0 mg carrier). The immobilized GOD showed maximal catalytic activity at pH 6.5 and 40 °C. After immobilization, the GOD exhibited improved thermal, storage and operation stability. The immobilized GOD still maintained 80% of its initial activity after the incubation at 50 °C for 25 min, whereas free enzyme had only 20% of initial activity after the same incubation. After kept at 4 °C for 28 days, the immobilized and free enzyme retained 87% and 40% of initial activity, respectively. The immobilized GOD maintained approximately 57% of initial activity after reused 7 times. The K_M (Michaelis-Menten constant) values for immobilized GOD and free GOD were 14.6 mM and 27.1 mM, respectively.     

Preparation and characterization of bifunctional, Fe3O4/ZnO nanocomposites and their use as photocatalysts

Bifunctional magnetic-optical Fe₃O₄/ZnO nanocomposites with different molar ratio were successfully synthesized by a facile two-step strategy. Compared with the other methods, it was found to be mild, inexpensive, green, convenient and efficient. Fe₃O₄ nanocrystal was used as seed for the deposit and growth of ZnO nanoparticle. A series of the characterizations manifested that the combination of Fe₃O₄ with ZnO nanoparticles was successful. Photocatalytic activity studies confirmed that as-prepared nanocomposites had excellent photodegradating behavior to Methyl Orange (MO) compared to the pure ZnO nanoparticles. The results showed that the degradation percentage of MO was about 93.6% for 1 h when the amount of catalyst was 0.51 g L⁻¹ and initial concentration of MO was 6 × 10⁻⁵ mol L⁻¹ in the pH 7 solution. Moreover, the kinetics of photocatalytic degradation reaction could be expressed by the first-order reaction kinetic model. Furthermore, the Fe₃O₄/ZnO nanocomposites could be also served as convenient recyclable photocatalysts because of their magnetic properties.     

Synthesis and properties of Au-Fe3O4 and Ag-Fe3O4 heterodimeric nanoparticles

Monodisperse Au-Fe 3 O 4 heterodimeric nanoparticles (NPs) were prepared by injecting precursors into a hot reaction solution.The size of Au and Fe 3 O 4 particles can be controlled by changing the injection temperature.UV-Vis spectra show that the surface plasma resonance band of Au-Fe 3 O 4 heterodimeric NPs was evidently red-shifted compared with the resonance band of Au NPs of similar size.The as-prepared heterodimeric Au-Fe 3 O 4 NPs exhibited superparamagnetic properties at room temperature.The Ag-Fe 3 O 4 heterodimeric NPs were also prepared by this synthetic method simply using AgNO 3 as precursor instead of HAuCl 4.It is indicated that the reported method can be readily extended to the synthesis of other noble metal conjugated heterodimeric NPs.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Preparation and magnetic properties of BaFe12O19/Ni0.8Zn0.2Fe2O4 nanocomposite ferrite

Nanocomposite of hard (BaFe₁₂O₁₉)/soft ferrite (Ni_0.8Zn_0.2Fe₂O₄) have been prepared by the sol–gel process. The nanocomposite ferrite are formed when the calcining temperature is above 800 °C. It is found that the magnetic properties strongly depend on the presintering treatment and calcining temperature. The “bee waist” type hysteresis loops for samples disappear when the presintering temperature is 400 °C and the calcination temperature reaches 1100 °C owing to the exchange-coupling interaction. The remanence of BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite with the mass ratio of 5:1 is higher than a single phase ferrite. The specific saturation magnetization, remanence magnetization and coercivity are 63 emu/g, 36 emu/g and 2750 G, respectively. The exchange-coupling interaction in the BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite is discussed.     

Synthesis and properties of colloidal ternary ZnGa2O4:Eu nanocrystals

A nonhydrolytic hot solution synthesis technique was used to grow monodisperse ternary oxide nanocrystals of ZnGa₂O₄:Eu³⁺. The shape of ZnGa₂O₄:Eu³⁺ nanocrystals was a function of the type of precursor, and their size was controlled by changing the concentration ratio of Zn precursor to surfactant. The crystal structure of synthesized ZnGa₂O₄ nanocrystals was a cubic spinel with no detectable secondary phases. Photoluminescence of red-emitting ZnGa₂O₄:Eu³⁺ nanocrystals resulted in a high (⁵D₀-⁷F₂)/(⁵D₀-⁷F₁) intensity ratio, suggesting that the Eu³⁺ ions occupy tetrahedral Zn²⁺ sites or distorted octahedral Ga³⁺ sites with no inversion symmetry in ZnGa₂O₄ nanocrystals.     

Synthesis and characterization of wire-like and near-spherical Eu2O3-doped Y2O3 phosphors by solvothermal reaction

Eu₂O₃-doped yttrium oxide (3 mol%) [Y₂O₃:Eu(3 mol%)] with wire-like and near-spherical morphologies were prepared by a solvothermal treatment using water, ethanol, ethylene glycol and glycerol as reaction media followed by calcination. The powders prepared in water and ethanol possessed wire structure, where the powder treated in water showed high aspect ratio and that in ethanol showed low aspect ratio. The powders prepared in ethylene glycol and glycerol possessed well-dispersed near-spherical powders, which showed almost the same level of photoluminescence emission intensity as that of submicron particles prepared without solvothermal treatment.     

Al掺杂的尖晶石型LiMn2O4的结构和电子性质

采用基于密度泛函理论的第一性原理方法, 在广义梯度近似(GGA)和GGA+U方法下对尖晶石型LiMn₂O₄及其Al掺杂 的尖晶石型LiAl_0.125Mn_1.875O₄晶体的结构和电子性质进行了计算. 结果表明: 采用GGA方法得到尖晶石型LiMn₂O₄是立方晶系结构, 其中的Mn离子为+3.5价, 无法解释它的Jahn-Teller 畸变. 给出的LiMn₂O₄能带结构特征也与实验结果不符. 而采用GGA+U方法得到在低温下的LiMn₂O₄和其掺杂 体系LiAl_0.125Mn_1.875O₄的晶体都是正交结构, 与实验一致. 也能明确地确定Mn的两种价态Mn³⁺/Mn⁴⁺的分布并且能够说明Mn³⁺O₆的z方向有明显的Jahn-Teller 畸变, 而Mn⁴⁺O₆则没有畸变. LiMn₂O₄的能带结构与实验比较也能够符合. 采用GGA+U方法对Al掺杂体系的LiAl_0.125Mn_1.875O₄的研究表明, 用Al替换一个Mn不会明显地改变晶体的电子性质, 但可以有效地消除Al³⁺O₆ 八面体的Jahn-Teller畸变, 从而改善正极材料LiMn₂O₄的性能, 这与电化学实验的观察结果相一致.     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

Novel approach to preparation of LiMn2O4 core/LiNixMn2−xO4 shell composite

Combining two methods, coating and doping, to modify spinel LiMn₂O₄, is a novel approach we used to synthesize active material. First we coated the LiMn₂O₄ particles with the nickel oxide particles by means of homogenous precipitation, and then the nickel oxide-coated LiMn₂O₄ was calcined at 750 °C to form a LiNi_xMn_2−xO₄ shell on the surface of spinel LiMn₂O₄ particles. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), cyclic voltammetry (CV) and charge-discharge test were performed to characterize the spinel LiMn₂O₄ before and after modification. The experimental results indicated that a spinel LiMn₂O₄ core is surrounded by a LiNi_xMn_2−xO₄ shell. The resulting composite showed excellent electrochemical cycling performance with an average fading rate of 0.014% per cycle. This improved cycle stability is greatly attributed to the suppression of Jahn-Teller distortion on the surface of spinel LiMn₂O₄ particles during cycling.     

超声强化合成MgFe2O4纳米颗粒及其机理研究

用超声水解方法制备MgO纳米颗粒,用化学沉淀法制备α-Fe₂O₃纳米颗粒,将MgO/α-Fe₂O₃混合体常温下超声活化2h,400℃固相合成制备出MgFe₂O₄纳米颗粒.通过X射线衍射和透射电子显微镜测试产品的化学成分、晶体结构和形貌尺寸,分析声化学反应机理及其影响因素.研究结果表明:所制备的MgFe₂O₄为尖晶石铁氧体,颗粒尺寸分布在20-30nm之间,粒度分布均匀;超声空化效应提高了化学反应活性、增加反应物的比表面积和反应物之间的接触面积,促进固相合成反应速度,降低反应温度,实现了一般条件下难以完成的化学反应.