6种化学计量学法同时分光光度测定5组分的比较研究及食品分析

优化了在表面活性剂存在下以肉桂基荧光酮同时测定铝、铜、锰、锌、钴的显色折衷条件；比较研究了偏最小二乘、岭回归、多元线性回归、多元逐步回归、目标因子分析和卡尔曼滤波法用于这一体系同时测定此５组分的优缺点，结果表明对于此类所含各组分吸收光谱重叠严重且吸光度加和性欠佳体系，上述６法中以偏最小二乘和岭回归法为最适宜；经用于九种人工合成液和四种食品分析，均获满意结果，分析两种茶叶结果也与ＩＣＰ－ＡＥＳ法一致     

两种全光谱技术同时测定铜、镉、锌

建立了一种小波软阈值法（STWPLS）同时测定铜（Ⅱ）、镉（Ⅱ）、锌（Ⅱ）方法。此法结合多分辩分析和软阈值法改进除噪质量。通过最佳化，小波函数，低频收缩截止水平（L）和阈值法类型分别选为Daubechies8,3和HYBRID。并将此法与偏最小二乘法（PLS）做了比较。     

同时测定铁钴铜的小波软阈值核心偏最小二乘法

提出了一种小波软阈值核心偏最小二乘法，同时测定铁、钴、铜；该法结合小波软阈值法和主组分分析改进除噪声质量，与其它软阈值法比较选用了HYBRID法；通过最佳化，小波函数和低频截止收缩水平（L）分别选用Symmlet6和2；设计了一个名为软阈值小波核心偏最小二乘法（STWKPLS）的程序进行全部计算，实验结果表明该法是成功的，并且优于核心偏最小二乘法。     

EDTA有色络合物吸收光谱的研究及其应用

研究了EDTA与铜、镍、钴、铁和铬的吸收光谱,对于相互之间影响,用影响系数和混合标准溶液校正法加以消除。方法应用于铜合金、锌白铜、钴铜液以及铬铁合金分析,测定结果与其它方法相一致。     

傅里叶变换用于铁和锌的同时光度测定

研究了傅里叶变换技术用于铁锌二组分的同时分光光度测定，采用傅里叶变换对吸光度数据进行预处理，再结合目标转换因子分析或偏最小二乘分析，结果较普通的目标转换因子分析或偏最小二乘法有显著改善。以傅里叶变换－偏最小二乘法就用于实际铝合金样品中铁和锌的同时测定，结果令人满意。     

同时测定合成样中铜钴镍钒含量的分光光度法--主成分回归法和偏最小二乘法比较

研究了主成分回归和偏最小二乘方法在多组分分光光度法分析中的应用,以５－Ｂｒ－ＰＡＤＡＰ（２〔５－溴－２－吡啶）－偶氮〕５－二乙氨基苯酚）为显色剂,ＯＰ（聚乙二醇辛基苯基醚）作为增溶增稳剂,在ｐＨ＝３．６的条件下,用主成分回归及偏最小二乘分光光度法同时测定了合成样中的铜、钴、镍、钒４组分含量,测定相对误差在－６．００％～４．００％之间。实验证明,对于加和性不好的体系偏最小二乘分光光度法要优于主成分回     

利用混合线性分析分光光度法同时测定微量铜、锌、镍

研究以5 Br PADAP为显色剂,用混合线性分析分光光度法同时测定铜、锌、镍。在pH8.2的硼砂 盐酸缓冲溶液中,Cu2 、Zn2 、Ni2 分别与5 Br PADAP形成稳定的配合物,其吸收光谱相互重叠。用一种新的数学模型,即混合线性分析进行光谱分辨,各组分的纯光谱则用最小二乘法求得。讨论了反应条件、测量波长的选择等因素的影响。铜、锌、镍的标准回收率分别为95.0%～102.5%、94.2%～101.3%和96.2%～104.2%。应用于铝合金中铜、锌、镍的同时测定。     

阻尼最小二乘－分光光度法用于多组分分析

基于阻尼最小二乘法原理改进ＣＰＡ法。在确定Ｐ系数矩阵时引入阻尼因子从而降低其病态程度即对偶然实验误差的敏感程度。此法用于多组分分析，如测定复合维生素Ｂ结果良好。     

阻尼最小二乘—分光光度法用于多组分分析

基于阻尼最小二乘法原理改进ＣＰＡ法。在确定Ｐ系数矩阵时引入阻尼因子从而降低其病态程度即对偶然实验误差的敏感程度。此法用于多组分分析，如测定复合维生素Ｂ结果良好。     

二极管阵列检测—偏最小二乘吸光光度法同时测定铜锌

研究了以２－（５－溴－２－噻唑偶氮）５－二乙氨基苯酚（５－Ｂｒ－ＰＡＤＡＰ）作显色剂,ＣＣＤ（Ｃｈａｒｇｅ Ｃｏｕｐｌｅｄ Ｄｅｖｉｃｅ,电荷耦器件）二极管阵列检测分光光度装置采及收光谱,用偏最小二乘法解析,同时测定了粮食中铜和锌。方法的线性范围锌为０．０５～０．４０μｇ．ｍｌ＾－１,铜为０．０２～０．６０μｇ．ｍｌ＾－１;检出限铜为０．０２μｇ．ｍｌ＾－１,平均加标回收率锌为９３．３％～９５．７     

ICP-AES法测定方铅矿中多元素的方法研究

采用电感耦合等离子体原子发射光谱法(ICP-AES)进行方铅矿中多元素同时测定.通过对方铅矿样品化学处理试验建立了HCl-NH4Cl-HNO3的溶矿体系.本体系采用基体匹配、背景系数和元素干扰系数校正及元素内标法确定了最佳综合实验测试条件.本实验建立的ICP-AES法同时测定方铅矿中镉、钴、铜、铁、铟、铅、锌7种元素的方法,本方法测量相对误差RE (n=8)为1.50%～7.50%,相对标准偏差RSD (n=8)为1.7%～5.7%.经国家一级标准物质GBW 07269分析验证可以满足方铅矿单矿物样品的分析要求.     

Determination of Co, Cu, Fe, Ga, W, and Zn in rocks by neutron activation and anion-exchange separation

A neutron-activation method for the simultaneous determination of cobalt, copper, gallium, iron, tungsten and zinc in rocks is described. The method is based on anion-excbange separation in hydrochloric acid media. Chemical yield is higher than 97% for all elements, except for tungsten, where the recovery of the carrier is established by re-activation. The precision is about 1-3% for the iron determination and about 3% for cobalt, copper, gallium and zinc.     

H-point standard addition method for simultaneous determination of cobalt(II) and zinc(II) ions

The H-point standard addition method (HPSAM) was applied to the simultaneous determination of zinc(II) and cobalt(II). This method is based on the difference in the absorbance of methylthymol blue complexes of Zn(II) and Co(II) at pH 6 buffered solution in different wavelength pairs. The results showed that Zn(II) and Co(II) can be determined simultaneously with concentration ratios of 20:1 and 1:7.5. Under working conditions, the proposed method was successfully applied to the simultaneous determination of zinc and cobalt in synthetic and real samples.     

两波长结合—多波长线性回归分光光度法同时测定3组分的研究

本文提出分光光度同时测定３组分的两波长结合－多波长线性回归法，不需要等吸收点，对ＰＡＲ－铜，锌，钴体系合成样测定的结果较为满意。     

Simultaneous Spectrophotometric Determination of Cadmium, Zinc and Copper with Kalman Filter

The compound 2-QADNm can form red complexes with caamium(II), zinc(II) and copper(II). The simultaneous determination of cadmium, zinc and copper with Kalman Filter is described in this paper, the proposed method was applied to a two-component system for determining cadmium and copper,and a three-component system for determining cadmium, zinc and copper.     

H-point standard addition method for simultaneous determination of cobalt(II) and zinc(II) ions

The H-point standard addition method (HPSAM) was applied to the simultaneous determination of zinc(II) and cobalt(II). This method is based on the difference in the absorbance of methylthymol blue complexes of Zn(II) and Co(II) at pH 6 using different wavelength pairs. The results showed that Zn(II) and Co(II) can be determined simultaneously with concentration ratios of 20:1 and 1:7.5. Under working conditions, the proposed method was successfully applied to the simultaneous determination of zinc and cobalt in synthetic, drinking water and vitamin samples.     

偏最小二乘分光光度法同时测定痕量铁、锰、铜、锌、钴和镍

痕量Fe^3 ,Mn^2 ,Cu^2 ,Zn^2 ,Co^2 ,Ni^2 与2－（5－溴－2－吡啶偶氮）－5－二乙氨基苯酚（5－Br-PADAP)和溴化十六烷基三甲基铵（CTMAB）在PH8．3时发生高灵敏显色反应，所形成的三元胶束络合的吸收光谱严重重叠，采用偏最小二乘法（PLS）辅助分光光度法测定了合成试样及饲料中上述6种痕量组分，结果表明，PLS法是化学计量学中一种可适用于基体较复杂的实际试样中痕量组分分光度同时测定的多元计算方法。     

Spectrophotometric simultaneous determination of cobalt, copper and nickel using nitroso-R-salt in alloys by partial least squares

Partial least squares modeling as a powerful multivariate statistical tool applied to spectrophotometric simultaneous determination of cobalt, copper, and nickel in aqueous solutions. The concentration range for cobalt, copper and nickel were 0.4-2.6, 0.6-3.4, 0.5-5.5 ppm, respectively. The experimental calibration set was composed with 36 sample solutions using a mixture design for three component mixtures. The absorption spectra were recorded from 470 to 600 nm. The effect of pH on the sensitivity and selectivity was studied according to net analyte signal (NAS). The values of root mean square difference (RMSD) for cobalt, copper and nickel using partial least squares (PLS) were 0.0192, 0.0263 and 0.0446 ppm, respectively. The effects of various cations and anions were investigated. The method was used to determination of cobalt, copper and nickel in two sample alloys based on copper, nickel and cobalt (known as cunico) and based on cobalt, nickel and iron (known as conife).     

Simultaneous determination of cobalt,copper, iron and vanadium in crude petroleum oils by HPLC

Summary A method has been developed for the simultaneous formation and solvent extraction of cobalt (II), copper (II), iron (II) and vanadium (IV) complexes of bis (acetylpivalylmethane)ethylenediamine (H₂APM₂en) in methyl isobutyl ketone. The complexes are eluted from a reversed phase HPLC column with a mixture of methanol:water:acetonitrile and detection was at 260 nm. The method has been applied to the simultaneous determination of cobalt, copper, iron and vanadium in crude petroleum oils at the ng level.     

Determination of transition metal ions in tobacco as their 2-(2-quinolinylazo)-5-dimethylaminophenol derivatives using reversed-phase liquid chromatography with UV-VIS detection

This paper reports the utilization of solid-phase extraction and the reversed-phase high-performance liquid chromatography for the determination of six important transition metal ions: iron, cobalt, nickel, copper, zinc and manganese in tobacco with 2-(2-quinolinylazo)-5-dimethylaminophenol (QADMAP) as chelating reagent. Iron, cobalt, nickel, copper, zinc and manganese ions react with QADMAP to form colored chelates in the medium of acetic acid-sodium acetate buffer solution (pH 4.0). These chelates can be enriched by solid-phase extraction with Waters Sep-Pak-C18 cartridge, and eluted the retained chelates from cartridge with tetrahydrofuran. The chelates were separated on a Waters Nova-Pak-C18 column (150x3.9 mm, 5 microm) by gradient elution with methanol (containing 0.5% of acetic acid) and 0.05 mol/l pH 4.0 acetic acid-sodium acetate buffer solution as mobile phase at a flow-rate of 0.5 ml/min. The detection limits of iron, cobalt, nickel, copper, zinc and manganese are 10, 12, 8, 13, 17 and 22 ng/l, respectively. This method had been applied to the determination of iron, cobalt, nickel, copper, zinc and manganese in tobacco with good results.