Study of adsorption of methylene blue and new methylene blue in liquid-solid interface by slab optical waveguide spectroscopy

A slab optical waveguide (SOWG) has been used for study of adsorption of both methylene blue (MB) and new methylene blue (NMB) in liquid–solid interface. Adsorption characteristics of MB and NMB on both bare SOWG and silanized SOWG by octadecyltrichlorosilane (ODS) were compared. Effect of pH on adsorption on MB and NMB was investigated. Binding rate constant analysis showed that both MB and NMB on bare SOWG demonstrates larger association constants than those on ODS-SOWG. Interactions of MB and NMB on bare SOWG and ODS-SOWG were analyzed by molecular mechanics calculation method. The binding energy change was in the following order: E_NMB–bare > E_MB–bare > E_NMB–ODS > E_MB–ODS.     

Comparative study for the removal of methylene blue via adsorption and photocatalytic degradation

Physically and chemically activated carbons were prepared from date pits and olive stones. Titania and WO(x)-TiO(2)/MCM-41 were prepared as photoactive catalysts. Surface characterizations were investigated from ash content, pH, base neutralization capacities and FT-IR techniques. The textural characteristics, namely specific surface area (S(BET)) and pore texture, were determined from low temperature adsorption of N(2) at 77 K. The decolorization of aqueous solution of methylene blue was performed by means of two alternative methods. Steam-activated carbons own higher surface area compared with ZnCl(2)-activated carbons, and the micropore surface area represents the major contribution of the total area. Steam-activated carbons were the most efficient decolorizing adsorbents owing to its higher surface area, total pore volume and the basic nature of the surface. The calculated values of DeltaG(0), DeltaH(0) and DeltaS(0) indicate the spontaneous behavior of adsorption. The photocatalytic degradation is more convenient method in decolorizing of methylene blue compared with the adsorption process onto activated carbons.     

Synthesis,structural characterization and reactivity of manganese tungstate nanoparticles in the oxidative degradation of methylene blue

Nanoparticles of manganese tungstate (MnWO₄) were prepared via an impregnation method using Mn(NO₃)₂·4H₂O and WO₃ as a source of Mn and W, respectively. The morphology of the manganese tungstate nanoparticles was studied in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). MnWO₄ nanoparticles showed severe catalytic performances for the degradation of organic dye (methylene blue, MB) in the presence of tert-butyl hydrogen peroxide, TBHP, as the oxidant at room temperature in water.     

Protein determination using methylene blue in a synchronous fluorescence technique

A new method for detecting protein by synchronous fluorescence enhancement was developed, based on the combination of near infrared (NIR) fluorescence and the dedimerization phenomenon of methylene blue (MB). Under analytical conditions, there are linear relationships between the enhancing extent of synchronous fluorescence of MB-sodium dodecyl benzene sulfonate (SDBS)-protein at 667 nm and the concentration of protein in the range of 8.0 × 10⁻⁸-4.0 × 10⁻⁵ g mL⁻¹ for bovine serum albumin (BSA), 1.0 × 10⁻⁷-3.5 × 10⁻⁵ g mL⁻¹ for egg albumin (EA). The detection limits (S/N = 3) of BSA and EA are 8.9 ng mL⁻¹ and 10.0 ng mL⁻¹, respectively. The fluorescence enhancement mechanism is discussed in detail. Results from multiple techniques indicate that the fluorescence enhancement of the system originates from the hydrophobic microenvironment provided by BSA and SDBS, and the formation of an MB-SDBS-BSA complex, as well as the deaggregation of some MB dimer.     

Simultaneous determination of methylene blue and new methylene blue by slab optical waveguide spectroscopy and artificial neural networks

A slab optical waveguide (SOWG) has been used for study of adsorption of both methylene blue (MB) and new methylene blue (NMB) in liquid-solid interface. Adsorption characteristics of MB and NMB on both bare SOWG and silanized SOWG by octadecyltrichlorosilane (ODS) were compared. The simultaneous determinations of both MB and NMB were explored by flow injection SOWG spectrophotometric analysis and artificial neural networks (ANNs) for the first time. Concentrations of MB and NMB were estimated simultaneously with the ANNs. Results obtained with SOWG were compared with those got by conventional UV-visible spectrophotometry.     

A novel study on synthesis of egg shell based activated carbon for degradation of methylene blue via photocatalysis

Egg shell-based activated carbon was successfully synthesized by the simple chemical activation process. Orthophosphoric acid and sodium hydroxide used as an activation agent. XRD pattern reveals the hexagonal structure of activated carbon. The functional group presents in activated carbon was identified using FT-IR spectroscopy. SEM images show irregular shapes of carbon. The photocatalytic performance of investigated activated carbon by illuminating methylene blue dye under UV–Visible irradiations. Photocatalytic activity of activated carbon results maximum degradation efficiency of 83%. Adsorption efficiency have been increased with respect of time for degradation of dye. Free radicals and superoxide’s play a significant role is decolourization of methylene blue. Photocatalytic activity of activated carbon synthesized by Orthophosphoric acid results shows the high degradation efficiency when compared to NaOH.     

Green synthesis of loofah-based biosorbent via radiation grafting for effective removal of methylene blue

A new loofah-based biosorbent with high adsorption capacity for cationic dye was synthesized by a one-step co-radiation grafting method. The successful grafting of sodium 4-vinylbenzene sulfonate (SSS) onto loofah sponge (LFs) through electron beam radiation can significantly improve the remove capacity of methylene blue in wastewater. The biosorbent with a 409.67 mg/g of uptake capacity for methylene blue (MB), was higher than most of the loofah based adsorbents reported. FT-IR, elemental analysis, XRD, SEM and TG were used to analyze the changes in the functional group composition, element content, morphology, thermal stability of the obtained biosorbent. The pH, contact time, temperature and the effect of dosage on adsorption were also investigated. The results showed that the adsorption behavior well accorded with the pseudo-second-order kinetic and Langmuir adsorption model, which proved that the adsorption was a single-layered and chemisorption process. The thermodynamic parameters suggested a spontaneous and endothermic process. XPS analysis confirmed a potential adsorption mechanism was based on hydrogen bond interaction, electrostatic interaction and π-π stacking. Additionally, the adsorbent owned outstanding reusability, which could be reused five times with a slight reduction of removal rate. Overall, this research enriches the MB trapping agent and provides a new methods for the reuse of waste natural loofah sponge, and it will be a valuable research with the advantages of low cost and less environmental pollution.     

Removal of methylene blue by tea wastages from the synthesis waste waters

The tea wastages could remove methylene blue（MB） as a cationic dye from waste water corresponding to second-order kinetic model.Thermodynamic studies showed that adsorption equilibrium constant（K_L） and maximum adsorption capacities(Q_max) were increased with increasing temperature.The removal efficiency of MB for Co 0.01 mmol/L at optimum conditions was about 85%. The maximum uptake capacity(Q_max) of methylene blue in a batch reactor was 0.328,0.542 and 0.659 mmol/g at 15,25 and 40℃, respectively.The enthalpy change（ΔH） and entropy change（ΔS） were 11.356 kJ/mol and 20.563 J/（mol K）,respectively.     

Preparation of ZnS-Fluoropolymer nanocomposites and its photocatalytic degradation of methylene blue

The ZnS particles were immobilized on the surface of poly(vinylidene difluoride) (PVDF) mixing methacrylic acid (MAA)-trifluoroethyl acrylate (TFA) copolymer electrospun nanofibers. The PVDF and MAATFA copolymer nanofibers were prepared by electrospinning. Zinc ions were introduced onto the surface of nanofibers by coordinating with the carboxyls of MAA, and then sulfide ions were added to react with zinc ions to form ZnS particles under hydrothermal condition. The size and the amount of ZnS particles increased with the reaction time prolonging. The Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results reveal that a chemical interaction exists between ZnS and fluoropolymer fibers. The degradation rate of methylene blue in ZnS-fluoropolymer nanocomposite system was considerably higher than in that of ZnS powders system under UV irradiation. There may be an adsorption-migration-photodegradation process during the degradation of methylene blue by using ZnS-fluoropolymer nanocomposites as photocatalyst. The photocatalytic activity of ZnS-fluoropolymer nanocomposites changes indistinctively after 10 times repeating tests.     

Electrochemical determination of heparin using methylene blue probe and study on competition of Ba with methylene blue for binding heparin

Cyclic voltammetric investigation of the interaction of methylene blue (MB) with heparin (hep) at a gold electrode is presented. The combination of MB with heparin formed a nonelectroactive complex MB-hep, which resulted in the peak current decrease of MB. The anodic peak current difference of MB was found to be proportional to the concentration of heparin in the range of 0.666-64.5 μg mL⁻¹ with a detection limit of 270 ng mL⁻¹ and a satisfactory result was obtained for the determination of heparin in injection samples. The equilibrium constant for MB-hep complex was calculated to be 7.32 × 10⁵. The dynamic process of competition of Ba²⁺ with methylene blue for binding heparin was monitored using quartz crystal microbalance (QCM) technique. The reaction rate constant between Ba²⁺ and MB-hep was estimated to be 0.0022 s⁻¹.     

Super-assembled highly compressible and flexible cellulose aerogels for methylene blue removal from water

Physical adsorption is a common method to solve the contamination of methylene blue in dyeing wastewater. As a kind of adsorption material, cellulose aerogels with high porosity and surface areas have great potential application in methylene blue removal. However, the week hydrogen bonding between cellulose nanofibers making the cellulose aerogels with the poor mechanical properties and can be easily destroyed during adsorption. Hence, the preparation of cellulose aerogels with high mechanical strength is still a great challenge. Here, we report a robust super-assembly strategy to fabricate cellulose aerogels by combining cellulose nanofibers with PVA and M-K10. The resulting cellulose aerogels not only has a robust chemically cross-linked network, but also has strong H-bonds, which greatly enhance the mechanical properties. The resulting cellulose aerogels possess a low density of 19.32 mg/cm3.Furthermore, the cellulose aerogel shows 93% shape recovery under 60% strain(9.5 k Pa under 60% strain)after 100 cycles, showing excellent mechanical property. The adsorption capacity of cellulose aerogel to methylene blue solution of 20 mg/L is 2.28 mg/g and the adsorption kinetics and adsorption isotherms have also been studied. Pseudo-second-order kinetic model and Freundlich isotherm model are more acceptable for indicating the adsorption process of methylene blue on the cellulose aerogel. Thus, this compressible and durable cellulose aerogel is a very prospective material for dyeing wastewater cleanup.     

海螵蛸的不同处理工艺对溶液中亚甲基蓝和氰化氢吸附能力的影响研究

采用不同的处理工艺处理制备得到海螵蛸颗粒(CO),以活性炭(AC) 为空白对照,完成了三种海螵蛸颗粒在水溶剂体系下对亚甲基蓝(MB)和氰化氢(HCN)的吸附能力测试。实验结果显示,对MB吸附的能力：AC>>酸/碱处理并热活化的CO >酸/碱处理的CO>未经处理的CO; 对HCN的吸附能力：酸/碱处理并热活化的CO >酸/碱处理的CO > AC>未经处理的CO。这表明经过酸和碱处理、再热活化的CO有很强的HCN吸附能力,有望以其为原料制备出吸附力很强的HCN吸附材料,在卷烟烟气吸附方面具有良好的应用前景。     

Removal of cationic methylene blue and malachite green dyes from aqueous solution by waste materials of Daucus carota

In present study adsorption capacity of waste materials of Daucus carota plant (carrot stem powder: CSP and carrot leaves powder: CLP) was explored for the removal of methylene blue (MB) malachite green (MG) dye from water. The morphology and functional groups present were investigated by scanning electron microscope (SEM) and Fourier transform infrared (FTIR) spectroscopy. The operating variables studied were pH, adsorbent dose, ionic strength, initial dye concentration, contact time and temperature. Equilibrium data were analysed using Langmuir and Freundlich isotherm models and monolayer adsorption capacity of adsorbents were calculated. Kinetic data were studied using pseudo-first and pseudo-second order kinetic models and the mechanism of adsorption was described by intraparticle diffusion model.Various thermodynamic parameters such as enthalpy of adsorption ΔH°, free energy change ΔG° and entropy ΔS° were estimated. Negative value of ΔH° and negative values of ΔG° showed that the adsorption process was exothermic and spontaneous. Negative value of entropy ΔS° showed the decreased randomness at the solid–liquid interface during the adsorption of MB and MG onto CSP and CLP.     

Immobilization of cellulose extracted from Robinia Pseudoacacia seed fibers onto chitosan: Chemical characterization and study of methylene blue removal

The design of economical adsorbents to remove pollutants from contaminated water is attracting more attention. In this study, cellulose was successfully extracted from Robinia Pseudoacacia seed fibers and immobilized onto chitosan beads. The prepared spherical beads were then used for the biosorption of methylene blue dye from aqueous media. Samples were investigated using several analytical methods, namely FT-IR, XRD, EDX, SEM, and TGA analyses. The adsorption experiments showed that combining cellulose with chitosan improved the removal of methylene blue. The maximum uptake amount of methylene blue using cellulose–chitosan composite beads was 55 mg/g. However, it was about 35 mg/g at 20 °C for chitosan beads. The kinetic data complied strongly with the pseudo-second order equation, suggesting that the biosorption phenomenon has predominantly a chemical nature. Overall, the current study has shown a promising technique to design new adsorbents from abundant natural polymers for eliminating cationic dyes from water.     

Synchronous fluorescence determination of DNA based on the interaction between methylene blue and DNA

The fluorescence intensity of methylene blue (MB) quenched by DNA in the pH range of 6.5-8.0 was studied with synchronous fluorescence technology. A novel method for detecting single-stranded and double-stranded DNA was developed. The decreased fluorescence intensity at 664 nm is in proportion to the concentration of DNA in the range of 0.28-11.0 μmol L⁻¹ for ctDNA, 0.14-8.25 μmol L⁻¹ for thermally denatured ctDNA and 0.28-8.25 μmol L⁻¹ for hsDNA. The detection limits (S/N = 3) are 0.11, 0.04 and 0.04 μmol L⁻¹, respectively. The method is rapid, selective, and the reagents are lower toxic. It has been used for the determination of DNA in synthetic samples with good satisfaction. In addition, the interaction modes between MB and ctDNA and the mechanism of the fluorescence quenching were also discussed in detail. The experimental results from absorption spectra and fluorescence polarization indicate that the possible interaction modes between MB and DNA are the electrostatic binding and the intercalation binding.     

Intercalation of methylene blue into barium phosphate—synthesis and electrochemical investigation

Methylene blue (MB) was strongly retained inside the cavity of host layered barium phosphate, without leaching, and the intercalated compound was characterized through X-ray power diffraction (XRD), IR spectra and electrochemical measurements. The intercalated dye compound was incorporated into a carbon paste electrode and, by means of cyclic voltammetry and amperometry, its electrochemical properties were investigated. In various electrolyte solutions, changing the pH between 3 and 9, the midpoint potential remained practically constant at −0.15 V. This is not the usual behavior for MB, since it is known that in the solution phase the midpoint potential changes considerably with pH. These data suggest that methylene blue behaves as a guest molecule in the lamellar structure of the barium phosphate. The electrode formed by this host/guest composition was used to investigate NADH electrochemical oxidation.     

Electrochemical study of methylene blue/titanate nanotubes nanocomposite and its layer-by-layer assembly multilayer films

Titanate nanotubes (TNT) were proven to be efficient support for the immobilization of methylene blue (MB). UV–vis absorption and Fourier transform infrared spectra showed that the effect of MB absorbed on TNT was better than nanocrystalline anatase TiO₂ (TNP). The quantity of MB absorbed onto TNT was found to be greater than that of TNP and the electrode modified with the MB–TNT film was more stable due to the strong interaction between TNT and MB as well. The absorption of MB on TNT was impacted by the pH value of the reaction solution for the change of surface charge. Electrochemical oxidation of dopamine (DA) at different electrodes was studied. The result showed that the MB–TNT composite film exhibited excellent catalytic activities to DA compared to those of pure TNT, which is a result of the great promotion of the electron-transfer rate between DA and the electrode surface by the MB–TNT film. Furthermore, the layer-by-layer self-assembly behavior of the electrochemically functional MB–TNT nanocomposite was also discussed after obtaining the stable colloid suspension of MB–TNT. The excellent electrochemical ability and the easy fabrication of layered nanocomposite make the MB–TNT nanocomposite very promising in electrochemistry study and new nanotube-based devices.     

Voltammetric determination of DNA hybridization using methylene blue and self-assembled alkanethiol monolayer on gold electrodes

An electrochemical DNA biosensor based on the recognition of single stranded DNA (ssDNA) by hybridization detection with immobilized complementary DNA oligonucleotides is presented. DNA and oligonucleotides were covalently attached through free amines on the DNA bases using N-hydroxysulfosuccinimide (NHS) and N-(3-dimethylamino)propyl-N′-ethylcarbodiimide hydrochloride (EDC) onto a carboxylate terminated alkanethiol self-assembled monolayers (SAM) preformed on a gold electrode (AuE). Differential pulse voltammetry (DPV) was used to investigate the surface coverage and molecular orientation of the immobilized DNA molecules. The covalently immobilized probe could selectively hybridize with the target DNA to form a hybrid on the surface despite the bases being attached to the SAM. The changes in the peak currents of methylene blue (MB), an electroactive label, were observed upon hybridization of probe with the target. Peak currents were found to increase in the following order: hybrid-modified AuE, mismatched hybrid-modified AuE, and the probe-modified AuE which indicates the MB signal is determined by the extent of exposed bases. Control experiments were performed using a non-complementary DNA sequence. The effect of the DNA target concentration on the hybridization signal was also studied. The interaction of MB with inosine substituted probes was investigated. Performance characteristics of the sensor are described.     

Facile synthesis and characterization of Fe2O3 nanoparticles using L-lysine and L-serine for efficient photocatalytic degradation of methylene blue dye

In this work, Fe₂O₃ nanoparticles, abbreviated as OL and OS, were facilely synthesized by the combustion procedure using L-lysine and L-serine as organic fuels, respectively. Also, the OL and OS samples were identified using different instruments such as Raman spectrometer, FT-IR spectrophotometer, UV–Vis spectrophotometer, XRD, HR-TEM, BET surface area, and FE-SEM. The XRD confirmed that the mean grain size of OL and OS samples is 42.23 and 33.16 nm, respectively. The HR-TEM images confirmed that irregular, hexagonal, and spherical shapes, have an average diameter of 39.13 and 34.28 nm, were observed in the OL and OS samples, respectively. The BET surface area of the OL and OS samples is 16.20 and 28.34 m²/g, respectively. Additionally, the OL and OS samples were accomplished for the photocatalytic degradation of methylene blue dye in the absence and presence of hydrogen peroxide. The % degradation of 45 mL of 25 mg/L of methylene blue dye in the case of using OL and OS samples in the absence of hydrogen peroxide is 55.23 and 63.64 % after 120 min, respectively. Also, in the presence of hydrogen peroxide, the % degradation in the case of using OL and OS samples is 100 % after 35 and 25 min, respectively.