Development and validation of a method for quantitative determination of econazole nitrate in cream formulation by capillary zone electrophoresis

A simple, fast, inexpensive and reliable capillary zone electrophoresis (CZE) method for the determination of econazole nitrate in cream formulations has been developed and validated. Optimum conditions comprised a pH 2.5 phosphate buffer at 20 mmol L(-1) concentration, +30 kV applied voltage in a 31.5 cm x 50 microm I.D. capillary. Direct UV detection at 200 nm led to an adequate sensitivity without interference from sample excipients. A single extraction step of the cream sample in hydrochloric acid was performed prior to injection. Imidazole (100 microg mL(-1)) was used as internal standard. Econazole nitrate migrates in approximately 1.2 min. The analytical curve presented a coefficient of correlation of 0.9995. Detection and quantitation limits were 1.85 and 5.62 microg mL(-1), respectively. Excellent accuracy and precision were obtained. Recoveries varied from 98.1 to 102.5% and intra- and inter-day precisions, calculated as relative standard deviation (RSD), were better than 2.0%. The proposed CZE method presented advantageous performance characteristics and it can be considered suitable for the quality control of econazole nitrate cream formulations.     

Determination of anthocyanins in wine based on flow-injection, liquid--solid extraction, continuous evaporation and high-performance liquid chromatography--photometric detection

A continuous method, easy to automate, for the determination of anthocyanins in wine based on the coupling of continuous liquid–solid extraction, evaporation, HPLC individual separation and photometric detection is proposed. The target analytes are removed from the wine in a continuous fashion using a C₁₈ minicolumn and eluted with an aqueous solution (pH 2) with 16% acetonitrile. The eluted fraction is concentrated by solvent evaporation assisted by heat and dragging off the vapour using a flow of N₂. For in-line preconcentration, a continuous evaporation module was designed and located in the manifold between the solid-phase minicolumn and the injection valve of the chromatograph. In this way, injection of the sample into the dynamic system leads the plug through it for liquid–solid extraction of the anthocyanins, partial evaporation of the eluent (with a preconcentration factor as required) and transport to the high-pressure injection valve of the chromatograph, where individual separation and subsequent photometric detection take place. The method thus developed for the determination of malvidin-3-glucoside, cyanidin-3-glucoside and peonidin-3-glucoside anthocyanins in Spanish red wines is more sensitive than the batch manual method based on the same steps, has better linearity of the calibrations curves with lower detection limits and much wider determination range for the most abundant anthocyanins in wine. In addition, the method can be fully automated with low acquisition and maintenance costs.     

Development of a capillary zone electrophoresis method for caseinoglycomacropeptide determination

Caseinoglycomacropeptide (CGMP) is a polypeptide of 64 amino acid residues, derived from the C-terminal part of bovine κ-casein. A sensitive and selective capillary zone electrophoresis method has been developed and validated for the analysis and quantitation of CGMP. Separation is carried out at 30 kV, using an uncoated fused-silica capillary and 20 mM sodium citrate buffer at acidic pH 3.5. The described method allows the separation of various CGMP subcomponents. The validation data proves that the method has the requisite selectivity, sensitivity, reproducibility and linearity for CGMP assay and for quality control during CGMP manufacturing (batch-to-batch reproducibility).     

Development and validation of a capillary zone electrophoresis method for the determination of propranolol and N-desisopropylpropranolol in human urine

A simple, rapid and sensitive procedure using solid phase extraction and capillary zone electrophoresis for the determination of propranolol (a beta-blocker) and one of its metabolites, N-desisopropylpropranolol, has been developed and validated. The optimum separation of both analytes was obtained in a 37 cm × 75 μm fused silica capillary using 20 mmol/L phosphate buffer (pH 2.2) as electrolyte, at 25 kV and 30 °C, and hydrodynamic injection for 5 s. Prior to the electrophoretic separation, the samples were cleaned up and concentrated using a C₁₈ cartridge and then, eluted with methanol, allowing a concentration factor of 30.Good results were obtained in terms of precision, accuracy and linearity. The limits of detection were 28 and 30 μg/L for N-desisopropylpropranolol and propranolol, respectively. Additionally, a robustness test of the method was carried out using the Plackett-Burman fractional factorial model with a matrix of 15 experiments.The presented method has been applied to the determination of both compounds in human urine.     

Development and validation of a fast method for determination of free glycerol in biodiesel by capillary electrophoresis

In this study, a capillary electrophoresis (CE) methodology for the determination of free glycerol in biodiesel using oxidative cleavage with periodate was optimized and validated. The amount of iodate produced in the reaction was determined by CE. The optimized electrolyte was 20 mmol L(-1) glycine and 10 mmol L(-1) trifluoroacetic acid (direct UV detection, 210 nm). The short total analysis time (less than 28 s) was obtained using the short end injection mode. The optimization of the method was carried out using Peakmaster software. The choice of the components of the run electrolyte and of the internal standard (nitrate) was made through the use of effective mobility curves. A good correlation coefficient higher than 0.9991 and low LOD 4.3 mg L(-1) was obtained. The recovery of free glycerol was 95.4-102.4%. This method was used to determine glycerol in commercial biodiesel samples.     

Simultaneous determination of trans-resveratrol and sorbic acid in wine by capillary zone electrophoresis

A method for separation and determination of sorbic acid, a food and beverage preservative, and trans-resveratrol, a biomedically active substance, in wine by capillary zone electrophoresis is described. A solid-phase extraction step on C18-column prior to the electrophoretic separation providing lower detection limits was used for trans-resveratrol determination. For determination of sorbic acid direct analysis of wine (without a preconcentration step) was used. The method is rapid and sensitive and was applied to the analysis of wines from Alsace, France.     

Development and validation of a capillary zone electrophoretic method for the determination of bisphosphonate and phosphonate impurities in clodronate

Capillary zone electrophoresis with direct UV detection at low wavelength and reversed polarity was applied for the separation and quantitation of bisphosphonate and phosphonate impurities in clodronate bulk material. Polyacrylamide-coated capillaries were used to reduce the interactions between the analytes and the electric double layer of the capillary, and to minimize electroosmotic flow. Study was made of the major factors affecting the separation, i.e., pH and ionic strength of the electrolyte solution and various instrumental parameters. The developed method provided reproducible separations of clodronate and related impurities (between-day precision of migration times: RSD < 2.3%, 275 runs). Acceptable validation results in the impurity quantitation range of 0.5-7.5 microg ml(-1) (corresponding to 0.1-1.5% of clodronate working concentration) were obtained in specificity, within-day and between-day precision, accuracy and linearity.     

Development and validation of a capillary electrophoresis method for the characterization of sulfoethyl cellulose

To characterize sulfoethyl cellulose el samples, a capillary electrophoresis method was developed and validated sulfoethyl cellulose el was hydrolyzed, and the resulting d ‐glucose derivatives were analyzed after reductive amination with 4‐aminobenzoic acid using 150 mM boric acid, pH 9.5, as background electrolyte at 20°C and a voltage of 28 kV. Peak identification was derived from capillary electrophoresis with mass spectrometry using 25 mM ammonia adjusted to pH 6.2 by acetic acid as electrolyte. Besides mono‐, di‐, and trisulfoethyl d ‐glucose small amounts of disaccharides could be identified resulting from incomplete hydrolysis. The linearity of the borate buffer‐based capillary electrophoresis method was evaluated using d ‐glucose in the concentration range of 3.9–97.5 μg/mL, while limits of detection and quantification derived from the signal‐to‐noise ratio of 3 and 10 were 0.4 ± 0.1 and 1.2 ± 0.3 μg/mL, respectively. Reproducibility and intermediate precision were determined using a hydrolyzed sulfoethyl cellulose el sample and ranged between 0.2 and 8.8% for migration times and between 0.3 and 10.4% for peak area. The method was applied to the analysis of the degree of substitution of synthetic sulfoethyl cellulose el samples obtained by variation of the synthetic process and compared to data obtained by elemental analysis.     

Rapid capillary zone electrophoresis method for the determination of metal cations in beverages

A rapid and reliable capillary zone electrophoresis method for the determination of inorganic cations was developed. The complete separation of K⁺, Ba²⁺, Ca²⁺, Na⁺, Mg²⁺, Mn²⁺, Ni²⁺, Cd²⁺, Li⁺ and Cu²⁺ can be achieved in 4 min with a simple electrolyte composed by 10 mM imidazole as the carrier buffer and background absorbance provider and acetic acid as the complexing agent (pH 3.60). Injection was performed hydrostatically by elevating the sample at 10 cm for 30 s. The running voltage was +25 kV at room temperature. Indirect UV-absorption detection was achieved at 185 nm. The detection limit was in the range between 0.06 mg/l (Mg²⁺) and 0.57 mg/l (K⁺) and the quantification limits ranged from 0.10 mg/l (Ni²⁺) to 0.80 mg/l (Cu²⁺). The calibration graphs were linear in the concentration range from the quantification limit till at least 1 g/l in K⁺, 10 mg/l in Ba²⁺, Ca²⁺, Mg²⁺, Mn²⁺, Ni²⁺ and Cd²⁺, 40 mg/l in Na⁺ and 12 mg/l in Li⁺ and Cu²⁺. The repeatability, intraday and interday analysis were ≤1.55% and ≤3.64% for migration time and ≤3.38% and ≤3.63% for peak area. The method developed has been applied to several beverage samples with only a simple dilution and filtration treatment of the sample. The proposed method is simple, fast, cheap and it is achieved with common products in either laboratory. For these reasons, it is a very useful method for routine analysis.     

Instrumental validation in capillary electrophoresis and checkpoints for method validation

Capillary electrophoresis (CE) is increasingly being used in regulated and testing environments which demand validation. The design, development and production of CE instrumentation should be governed by qualifications which ensure the quality of the finished product. The vendor should therefore provide guidelines and procedures which assist the user in ensuring the adequate operation of the instrumentation and especially in designing installation qualification (IQ) and operational qualification/performance verification (OQ/PV) procedures. OQ/PV should test those functions of an instrument which directly affect the CE analysis, i.e. voltage, temperature, injection precision and detector function. In validation of CE methods care should be taken that those aspects which directly affect the precision of peak parameters are appreciated. The relationship between CE instrumentation, chemistry and validation parameters is discussed and guidelines are presented for definition of a CE method for submission to regulatory authorities.     

Development and validation of a capillary electrophoresis method with ultraviolet detection for the determination of the related substances in a pharmaceutical compound

A capillary electrophoresis (CE) method was successfully developed to quantify the impurity profile of a new substance of pharmacological interest: LAS 35917. CE method was developed in order to separate the chloromethylated, monomethylated and hydroxylated impurities (molecules with very similar chemical structures) having the three coelution in the reversed-phase LC method initially established. Taking into account the structure of the impurities of LAS 35917, separation by conventional liquid chromatography (LC) methods would be longer and tedious than separation by CE, which is an appropriate and versatile technique giving easier and quicker methods. Among the three potential impurities mentioned of LAS 35917, two are due to the synthesis route of this drug, and the third arises from degradation. These drug-related impurities were separated using a capillary of 56 cm of effective length and 50 microm I.D., a 60 mM tetraborate buffer, at pH 9.2, and a positive voltage of 20 kV. The optimised CE method was preliminary validated with regard to specificity, linearity, limits of detection and quantitation, repeatability and solution stability. The method allows the detection and quantitation of impurities above 0.04 and 0.08% level, respectively. All three related substances were separated, detected and quantified from their parent drug in the analysis of real samples of LAS 35917, stressed or not stressed, with this simple and fast CE method.     

Validation of a capillary zone electrophoresis method for the comparative determination of etoricoxib in pharmaceutical formulations

A CZE method was developed and validated for the analysis of etoricoxib in pharmaceutical dosage forms, using prilocaine as an internal standard. The CZE method was carried out on a fused-silica capillary (50 microm id, effective length 40 cm). The BGE consisted of 25 mM tris-phosphate solution at pH 2.5. The capillary temperature was maintained at 35 degrees C, the applied voltage was 25 kV, the injection was performed using the pressure mode at 50 mbar for 5 s, with detection at 234 nm using a photodiode array detector. The method was linear in the range of 2-150 microg/mL (r(2) = 0.9999). The specificity and stability-indicating capability were proven through the degradation studies and showing also that there was no interference of the excipients of the formulation. The accuracy was 99.49% with RSD of 0.66%. The limits of quantitation and detection were 2 and 0.58 microg/mL, respectively. Moreover, method validation demonstrated acceptable results for the precision, sensitivity, and robustness. The proposed method was successfully applied for the quantitative analysis of etoricoxib pharmaceutical formulations, and the results compared to the HPLC and LC-MS/MS methods, showing nonsignificant difference (p >0.05).     

Development and validation of a UHPLC method for the determination of flavonoids in red wine

A simple and fast ultra-high-performance liquid chromatography (UHPLC) method was developed for the identification and quantification of the following flavonoids in red wine: (+/-)-catechin, (-)-epicatechin, rutin, quercitrin, hesperidin, neohesperidin, (+/-)-naringenin, hesperetin, and chrysin. Chromatographic separation of the flavonoids was performed on a Chromolith Fast Gradient C18e column. A gradient elution was used with mobile phases consisting of 0.1% formic acid in water and acetonitrile. UV detection was performed at 280 nm. A complete separation of flavonoids was possible within 6 min. The calibration curves showed good linearity (R2 > or = 0.9990) in the selected range of each analyte; the LOD ranged between 0.06 and 0.19 microg/mL. An optimized sample preparation method utilized SPE. The Oasis HLB column with the highest recoveries was selected for the preconcentration step. This method was successfully applied to the determination of these flavonoids in the red wine samples with excellent results.     

Experimental design-based development and single laboratory validation of a capillary zone electrophoresis method for the determination of the artificial sweetener sucralose in food matrices

A capillary zone electrophoresis (CZE) method, optimised chemometrically, underwent a complete in-house validation protocol for the qualification and quantification of sucralose in various foodstuffs. Separation from matrix components was obtained in a dinitrobenzoic acid (3 mM)/sodium hydroxide (20 mM) background electrolyte with a pH of 12.1, a potential of 0.11 kV cm^–1 and a temperature of 22 °C. Detection was achieved at 238 nm by indirect UV. Screening, optimisation and robustness testing were all carried out with the aid of experimental design. Using standard addition calibration, the CZE method has been applied to still, carbonated and alcoholic beverages, yoghurts and hard-boiled candy. The method allows the detection of sucralose at >30 mg kg^–1, with a linearity range of 50–500 mg kg^–1, making it suitable for implementation of the recently amended Sweeteners for use in foodstuffs Directive (European Parliament and Council (2003) Off J L237:3–12), which set maximum usable doses of sucralose for many foodstuffs, most ranging from 200 mg kg^–1 to 450 mg kg^–1.     

Development of a capillary zone electrophoresis method for the separation of a furan combinatorial library

Nine component mixtures of a furan library were simultaneously separated by capillary zone electrophoresis (CZE) using a phosphate buffer as a background electrolyte at low pH. The effects of buffer concentration, buffer pH, type and concentration of organic solvents on the electrophoretic mobility, resolution, and analysis time were systematically investigated. Resolution and efficiency of furan library components were further improved using cyclodextrin (CD)-modified CZE. Under optimum conditions, eight of the nine furans were baseline-resolved in less than 10 min at 30 kV using 50 mM phosphate buffer, 10% v/v acetonitrile (ACN), pH 2.0, with 5 mM gamma-CD.     

Development and validation of capillary zone electrophoresis and high-performance liquid chromatography methods for the determination of oral anticoagulant edoxaban in pharmaceutical tablets

The incidence of thrombotic complications in SARS-CoV-2 infections has become a global concern; thus, anticoagulants are an integral part of the treatment. Edoxaban (EDX) is an oral anticoagulant suitable for pharmacologic thromboprophylaxis. Herein, two novel analytical methods for EDX determination in tablets are developed and validated using capillary zone electrophoresis (CZE) and high-performance liquid chromatography (HPLC). Operating conditions such as the electrolyte's concentration and pH value, injection time, volume, and the capillary temperature, were optimized. The methods were successfully validated by establishing the linearity, intra- and inter-day precisions (relative standard deviation [%]), accuracy, and robustness. Adequate separation of excipients and degradation products of EDX generated by stress degradation conditions demonstrated the stability-indicating capability of the methods. The analytical procedures were linear in the range of 25–125 µg/ml (r > 0.999), with the limits of detection and quantification of 3.26 and 10.87 µg/ml for CZE and 0.740 and 2.78 µg/ml for HPLC. Although both methodologies are suitable for determining EDX in tablets, CZE provides a greener alternative due to low-cost analysis using less organic solvents and minimizing waste generation.     

Development and validation of a capillary electrophoresis method for the determination of escitalopram and sensitive quantification of its enantiomeric impurity in formulations

A rapid capillary zone electrophoresis method has been developed capable of quantifying 0.05% of R-enantiomer and assaying the main component in escitalopram formulations. Many parameters influencing enantioseparation were investigated, which include chiral selectors, buffer composition and pH, applied voltage, capillary length, temperature, and rinsing procedure. Optimal separation conditions were obtained by using a 25 mM phosphate buffer at pH 7.0, containing 1.6% (w/v) sulfated-β-cyclodextrin with short-end injection at 0.5 psi for 5 s. Online UV detection was performed at 205 nm. A voltage of -20 kV was applied and the capillary temperature was kept at 25°C. Separation was achieved in less than 2 min. The method was further validated, including robustness, stability of the solution, selectivity, linearity (escitalopram from 0.25 μg/mL to 600 μg/mL, y = 1528.3 × +1812.9; R2 = 0.9999), LOD and LOQ (0.08 and 0.25 μg/mL, respectively), precision and accuracy. The proposed method was then applied to the quality control of the bulk sample and tablets of escitalopram (10 mg).     

Method development and validation for the simultaneous determination of four coumarins in Saussurea superba by capillary zone electrophoresis

A capillary zone electrophoretic method has been developed for the determination of four coumarins--skimmin, scopolin, scopoletin, and umbelliferone-in Saussurea superba with UV detection at 254 nm. The capillary temperature was kept constant at 25 degrees C. Effects of buffer pH, electrolyte concentration, organic modifier, and applied voltage on migration behavior were studied systematically. The optimum conditions for separation were achieved by using 30 mM borate buffer at pH 9.02 containing 15% (v/v) methanol as the electrolyte and 25 kV as the applied voltage. For all analytes a good linear regression relationship (r > 0.999) was obtained between peak area and concentration over a relatively wide range. The method was validated for repeatability, precision, and accuracy. The validated method was successfully applied to the simultaneous determination of the four analytes in S. superba.     

Novel approach for the rapid determination of water-soluble organic acids in wine by co-electroosmotic flow capillary zone electrophoresis

An innovative protocol for the fast analysis of some organic acids in red wine by co-electroosmotic capillary zone electrophoresis and indirect UV detection using hexadimethrine bromide (HDB) as coating agent was proposed. The adsorption of HDB onto the capillary wall provided a stable electroosmotic flow and separation of small anions was carried out using background electrolytes containing no polymer additive. Low RSD% values (<3.6%) in terms of migration times and effective mobilities were obtained from the analysis of a mixture of nitrate and nitrite and of a mixture of organic acids. An experimental design approach was used to investigate the effects of temperature, separation voltage, and percentage of methanol added to the running buffer solution on the separation of the analytes. A faster method allowing the separation of the organic acids involved in the malolactic fermentation of wine was developed. Using a running electrolyte consisting of 35% (v/v) methanol in a solution of 22 mM benzoic acid at pH 6.10 adjusted with 1.0 M TRIS-base buffer, the separation of tartaric, malic, succinic, acetic, and lactic acids was feasible in less than 210 s. Application of the method to the quantification of the above-mentioned organic acids in Italian red wine samples is reported.     

Development and validation of a simple capillary zone electrophoresis method for the analysis of kanamycin sulfate with UV detection after pre-capillary derivatization

Capillary zone electrophoresis was successfully applied to separate eight related substances of kanamycin and several minor unknowns from the main component. Strategies to enhance derivatization and selectivity and to optimize separation parameters involved the application of experimental designs. This chemometrical approach considers main effects as well as interactions of the influential parameters, thus conducting a more thorough investigation of the method than the common step-by-step approach. Central composite face centered designs established optimal separation conditions: 30 mM borax buffer, pH 10.0 containing 16.0% (v/v) methanol and optimal composition of derivatization reagent: 27 mg/ml 1,2-phthalic dicarboxaldehyde and 25 microl/ml mercaptoacetic acid in borate buffer, pH 10.4. The standard curves were linear over the concentration range of 0.007-1.01 mg/ml for the main component and 0.003-0.1 mg/ml for the related substances. The limit of quantitation was 0.14% (m/m) for the related substances and impurities (S/N= 10). The assay method was used to determine the composition of several commercial samples. Quantitative analysis indicates potential usefulness of capillary electrophoresis as an alternative to the assay method prescribed in the European Pharmacopoeia and the United States Pharmacopeia.