Sonochemical Preparation of Hierarchical ZnO Hollow Spheres for Efficient Dye‐Sensitized Solar Cells

Hierarchical ZnO hollow spheres (400–500 nm in diameter) consisting of ZnO nanoparticles with a diameter of approximately 15 nm have been successfully prepared by a facile and rapid sonochemical process. The formation of hierarchical ZnO hollow spheres is attributed to the oriented attachment and subsequent Ostwald ripening process according to time‐dependent experiments. The as‐prepared ZnO hollow spheres are used as a photoanode in dye‐sensitized solar cells and exhibit a highly efficient power conversion efficiency of 4.33 %, with a short‐circuit current density of 9.56 mA cm^?2, an open‐circuit voltage of 730 mV, and a fill factor of 0.62 under AM 1.5 G one sun (100 mW cm^?2) illumination. Moreover, the photovoltaic performance (4.33 %) using the hierarchical ZnO hollow spheres is 38.8 % better than that of a ZnO nanoparticle photoelectrode (3.12 %), which is mainly attributed to the efficient light scattering for the former.     

Nd‐Doped TiO2 Nanorods: Preparation and Application in Dye‐Sensitized Solar Cells

Monodispersed Nd‐doped TiO₂ nanorods (20 nm×2 nm) were synthesized by solvothermal methods and characterized by TEM, XRD, and EDS. Application of the nanorods for modifying conventional photoanodes in dye‐sensitized solar cells (DSSCs) was investigated. Data show that, after modification, an enhancement of the incident‐photon‐to‐current conversion efficiency (IPCE) in the whole range of visible light was observed and an increase of 33.3 % for overall conversion efficiency was achieved. Our mechanistic proposal is that Nd ions doped on TiO₂ nanorods to some extent enhance the injection of excited electrons and decrease the recombination rate of the injected electrons.     

Photoanode Based on Chain‐Shaped Anatase TiO2 Nanorods for High‐Efficiency Dye‐Sensitized Solar Cells

Anatase TiO₂ nanorods with large specific surface areas and high crystallinity have been synthesized by surfactant‐free hydrothermal treatment of water‐soluble peroxotitanium acid (PTA). X‐ray diffraction and TEM analysis showed that all TiO₂ nanorods derived from PTA in different hydrothermal processes were in the anatase phase, and high aspect ratio TiO₂ nanorods with chain‐shaped structures were formed at 150 °C for 24 h by oriented growth. The nanorods were fabricated as photoanodes for high‐efficiency dye‐sensitized solar cells (DSSCs). DSSCs fabricated from the chain‐shaped TiO₂ nanorods gave a highest short‐circuit current density of 14.8 mA cm^?2 and a maximum energy conversion efficiency of 7.28 %, as a result of the presence of far fewer surface defects and grain boundaries than are present in commercial P25 TiO₂ nanoparticles. Electrochemical impedance spectroscopy also confirmed that DSSCs based on the TiO₂ nanorods have enhanced electron transport properties and a long electron lifetime.     

Platinum‐Free Binary Co‐Ni Alloy Counter Electrodes for Efficient Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSSCs) have attracted growing interest because of their application in renewable energy technologies in developing modern low‐carbon economies. However, the commercial application of DSSCs has been hindered by the high expenses of platinum (Pt) counter electrodes (CEs). Here we use Pt‐free binary Co‐Ni alloys synthesized by a mild hydrothermal strategy as CE materials in efficient DSSCs. As a result of the rapid charge transfer, good electrical conduction, and reasonable electrocatalysis, the power conversion efficiencies of Co‐Ni‐based DSSCs are higher than those of Pt‐only CEs, and the fabrication expense is markedly reduced. The DSSCs based on a CoNi_0.25 alloy CE displays an impressive power conversion efficiency of 8.39 %, fast start‐up, multiple start/stop cycling, and good stability under extended irradiation.     

Characterizing the Role of Iodine Doping in Improving Photovoltaic Performance of Dye‐Sensitized Hierarchically Structured ZnO Solar Cells

We report two novel types of hierarchically structured iodine‐doped ZnO (I? ZnO)‐based dye‐sensitized solar cells (DSCs) using indoline D205 and the ruthenium complex N719 as sensitizers. It was found that iodine doping boosts the efficiencies of D205 I? ZnO and N719 I? ZnO DSCs with an enhancement of 20.3 and 17.9 %, respectively, compared to the undoped versions. Transient absorption spectra demonstrated that iodine doping impels an increase in the decay time of I? ZnO, favoring enhanced exciton life. Mott–Schottky analysis results indicated a negative shift of the flat‐band potential (V_fb) of ZnO, caused by iodine doping, and this shift correlated with the enhancement of the open circuit voltage (V_oc). To reveal the effect of iodine doping on the effective separation of e^?‐h⁺ pairs which is responsible for cell efficiency, direct visualization of light‐induced changes in the surface potential between I? ZnO particles and dye molecules were traced by Kelvin probe force microscopy. We found that potential changes of iodine‐doped ZnO films by irradiation were above one hundred millivolts and thus significantly greater. In order to correlate enhanced cell performance with iodine doping, electrochemical impedance spectroscopy, incident‐photon‐current efficiency, and cyclic voltammetry investigations on I? ZnO cells were carried out. The results revealed several favorable features of I? ZnO cells, that is, longer electron lifetime, lower charge‐transfer resistance, stronger peak current, and extended visible light harvest, all of which serve to promote cell performance.     

Molecular Design Rule of Phthalocyanine Dyes for Highly Efficient Near‐IR Performance in Dye‐Sensitized Solar Cells

A series of zinc–phthalocyanine sensitizers ( PcS16 – 18 ) with different adsorption sites have been designed and synthesized in order to investigate the dependence of adsorption‐site structures on the solar‐cell performances in zinc–phthalocyanine based dye‐sensitized solar cells. The change of adsorption site affected the electron injection efficiency from the photoexcited dye into the nanocrystalline TiO₂ semiconductor, as monitored by picosecond time‐resolved fluorescence spectroscopy. The zinc–phthalocyanine sensitizer PcS18 , possessing one carboxylic acid directly attached to the ZnPc ring and six 2,6‐diisopropylphenoxy units, showed a record power conversion efficiency value of 5.9 % when used as a light‐harvesting dye on a TiO₂ electrode under one simulated solar condition.     

Three Keggin‐Type Transition Metal‐Substituted Polyoxometalates as Pure Inorganic Photosensitizers for p‐Type Dye‐Sensitized Solar Cells

In light of the serious challenge of severe global energy shortages, p‐type dye‐sensitized solar cells (p‐DSSCs) have attracted increasing levels of interest. The potential of three Keggin‐type transition metal‐substituted polyoxometalates, TBA₈Na₂[SiW₉O₃₇{Co(H₂O)₃}]? 11 H₂O (SiW₉Co₃), TBA₄[(SiO₄)W₁₀Mn^III₂O₃₆H₆]?1.5 CH₃CN? 2 H₂O (SiW₁₀Mn^III₂), and TBA_3.5H_5.5[(SiO₄)W₁₀Mn^III/IV₂O₃₆]? 10 H₂O?0.5 CH₃CN (SiW₁₀Mn^III/IV₂) has been explored as pure inorganic dye photosensitizers for p‐DSSCs (TBA=(n‐C₄H₉)₄N⁺). The three dyes show overall conversion efficiencies of 0.038, 0.029, and 0.027 %, respectively, all of which are higher than that of coumarin 343 (0.017 %). These polyoxometalates are the first three pure inorganic dyes reported for use with p‐DSSCs and therefore demonstrate a new strategy for designing efficient dyes, especially pure inorganic dyes. Moreover, they broaden the range of applications for polyoxometalates.     

Brookite TiO2 Nanoparticle Films for Dye‐Sensitized Solar Cells

Brookite TiO₂ nanoparticles have been synthesized at low temperature by a soft solution growth method and have been used as building blocks to prepare pure brookite nanoparticle porous films. The film brookite structure was confirmed by XRD and Raman spectroscopy. By spectrophotometry, it was shown that the films had a direct band gap of 3.4 eV. After sensitization by the N719 dye, efficient cells have been produced. A best overall conversion efficiency of 5.97 %, without a scattering layer, was found for the larger TiO₂ starting nanoparticles. The cell open‐circuit voltage was improved compared with that of anatase cells and a lower electron diffusion coefficient was found in the photoanodes made of smaller brookite particles. Lanthanum‐doped brookite nanoparticle films were also studied. They showed a marked decreased in the amount of dye loading, and hence, the solar cells had a reduced current density that was not compensated for by the increased open‐circuit voltage of the cells.     

Transparent Metal Selenide Alloy Counter Electrodes for High‐Efficiency Bifacial Dye‐Sensitized Solar Cells

The exploration of cost‐effective and transparent counter electrodes (CEs) is a persistent objective in the development of bifacial dye‐sensitized solar cells (DSSCs). Transparent counter electrodes based on binary‐alloy metal selenides (M‐Se; M=Co, Ni, Cu, Fe, Ru) are now obtained by a mild, solution‐based method and employed in efficient bifacial DSSCs. Owing to superior charge‐transfer ability for the I^?/I₃^? redox couple, electrocatalytic activity toward I₃^? reduction, and optical transparency, the bifacial DSSCs with CEs consisting of a metal selenide alloy yield front and rear efficiencies of 8.30 % and 4.63 % for Co_0.85Se, 7.85 % and 4.37 % for Ni_0.85Se, 6.43 % and 4.24 % for Cu_0.50Se, 7.64 % and 5.05 % for FeSe, and 9.22 % and 5.90 % for Ru_0.33Se in comparison with 6.18 % and 3.56 % for a cell with an electrode based on pristine platinum, respectively. Moreover, fast activity onset, high multiple start/stop capability, and relatively good stability demonstrate that these new electrodes should find applications in solar panels.     

Molecular Engineering of Push–Pull Porphyrin Dyes for Highly Efficient Dye‐Sensitized Solar Cells: The Role of Benzene Spacers

Porphyrins have drawn much attention as sensitizers owing to the large absorption coefficients of their Soret and Q bands in the visible region. In a donor and acceptor zinc porphyrin we applied a new strategy of introducing 2,1,3‐benzothiadiazole (BTD) as a π‐conjugated linker between the anchoring group and the porphyrin chromophore to broaden the absorption spectra to fill the valley between the Soret and Q bands. With this novel approach, we observed 12.75 % power‐conversion efficiency under simulated one‐sun illumination (AM1.5G, 100 mW cm^?2). In this study, we showed the importance of introducing the phenyl group as a spacer between the BTD and the zinc porphyrin in achieving high power‐conversion efficiencies. Time‐resolved fluorescence, transient‐photocurrent‐decay, and transient‐photovoltage‐decay measurements were employed to determine the electron‐injection dynamics and the lifetime of the photogenerated charge carriers.     

High‐Performance Platinum‐Free Dye‐Sensitized Solar Cells with Molybdenum Disulfide Films as Counter Electrodes

By using a radio‐frequency sputtering method, we synthesized large‐area, uniform, and transparent molybdenum disulfide film electrodes (1, 3, 5, and 7 min) on transparent and conducting fluorine‐doped tin oxide (FTO), as ecofriendly, cost‐effective counter electrodes (CE) for dye‐sensitized solar cells (DSSCs). These CEs were used in place of the routinely used expensive platinum CEs for the catalytic reduction of a triiodide electrolyte. The structure and morphology of the MoS₂ was analyzed by using Raman spectroscopy, X‐ray diffraction, and X‐ray photoemission spectroscopy measurements and the DSSC characteristics were investigated. An unbroken film of MoS₂ was identified on the FTO crystallites from field‐emission scanning electron microscopy. Cyclic voltammetry, electrochemical impedance spectroscopy, and Tafel curve measurements reveal the promise of MoS₂ as a CE with a low charge‐transfer resistance, high electrocatalytic activity, and fast reaction kinetics for the reduction of triiodide to iodide. Finally, an optimized transparent MoS₂ CE, obtained after 5 min synthesis time, showed a high power‐conversion efficiency of 6.0 %, which comparable to the performance obtained with a Pt CE (6.6 %) when used in TiO₂‐based DSCCs, thus signifying the importance of sputtering time on DSSC performance.     

Ultrafast Photodynamics of the Indoline Dye D149 Adsorbed to Porous ZnO in Dye‐Sensitized Solar Cells

We investigate the ultrafast dynamics of the photoinduced electron transfer between surface‐adsorbed indoline D149 dye and porous ZnO as used in the working electrodes of dye‐sensitized solar cells. Transient absorption spectroscopy was conducted on the dye in solution, on solid state samples and for the latter in contact to a I^?/I₃^? redox electrolyte typical for dye‐sensitized solar cells to elucidate the effect of each component in the observed dynamics. D149 in a solution of 1:1 acetonitrile and tert‐butyl alcohol shows excited‐state lifetimes of 300±50 ps. This signature is severely quenched when D149 is adsorbed to ZnO, with the fastest component of the decay trace measured at 150±20 fs due to the charge‐transfer mechanism. Absorption bands of the oxidized dye molecule were investigated to determine regeneration times which are in excess of 1 ns. The addition of the redox electrolyte to the system results in faster regeneration times, of the order of 1 ns.