Phase contribution to dynamic gratings recorded in Er-doped fiber with saturable absorption

Experimental observation of phase (i.e. refractive index) component in the dynamic gratings recorded in erbium-doped optical fiber with saturation of optical absorption is reported. We utilized configuration of transient two-wave mixing with rectangular phase modulation of one of counterpropagating recording waves, where unshifted phase grating resulted in a transient energy exchange. The reported experiments were performed with heavily doped (≈5400 ppm erbium) fibers in a wide spectral range of Er³⁺ fundamental absorption at selected laser wavelengths 1492, 1526, 1549, and 1568 nm. Relative contribution of phase grating was especially large (up to ≈100% of the maximal amplitude component) at the opposite sides of the investigated spectral range and was significantly lower in its central part. The amplitude grating was found especially strong at short wavelength side of the spectrum (i.e. at 1492 nm), where the grating amplitude proved to be only two times lower than the theoretically predicted from consideration of two-level model.     

Two-wave mixing via reflection population gratings

Theoretical analysis of two-wave mixing (TWM) via reflection population grating, aiming to support current experimental investigations of dynamic gratings in Erbium (Er)-doped fibers, is presented. It is shown that for low recording intensities the stationary TWM via reflection saturated absorption gratings is well described in approximation of a spatially uniform grating amplitude. The analysis of the transient TWM is performed both for rectangular and for sinusoidal phase modulation of one of the recording waves and it is shown how the recorded grating amplitude and characteristic recording time can be obtained from the detected signals. It is pointed out that the majority of the existing experimental results on TWM in Er-doped fibers are qualitatively explained within the framework of the developed model.     

光纤超声传感器及应用研究进展

光纤超声传感器通过检测光纤内传输光的强度、波长、相位、偏振态等参数感知超声波的相关信息.相比于传统的电类超声换能器,光纤超声传感器能够实现宽频带超声波信号的高灵敏探测,且其良好的抗干扰能力和复用性,可有效地提高超声波探测的可靠性和效率,在水下国防安全、生物成像、无损探伤、地震物理模型成像等领域具有巨大的应用潜力.目前,按照传感结构,光纤超声传感器可分为光纤强度调制型、光纤干涉型和光纤光栅型,并在不同方面发挥着各自的优势,均受到关注.本文主要综述了这几种传感器的传感机理、实现方法、发展现状,总结了光纤超声传感器的几个应用领域及面临的科学技术挑战,重点讨论了光纤超声传感器作为一种新技术应用于地震物理模型成像.     

Intensity dependence of the transient two-wave mixing by population grating in Er-doped fiber

Theoretical analysis of the transient two-wave mixing (TWM) of two continuous waves with rectangular phase modulation counter-propagating through the Er-doped optical fiber is presented. Approximate analytic solutions obtained for undepleted interacting waves of low power (neglecting large-scale saturation of the fiber optical absorption) and of high power (with significant spatially uniform large-scale absorption saturation) are complemented by numerical simulation for a broad region of the recording light power. The experimental dependence of the TWM efficiency on the recording power obtained for a single-mode fiber with ?640 ppm erbium concentration and with initial optical density ≈8.4 at λ = 1526 nm demonstrated the initial, growing and decaying parts predicted theoretically. The maximum experimentally observed relative TWM signal amplitude proved to be approximately 3 times lower than expected.     

A Novel Fabrication Technique of Long Period Fiber Gratings

１ＩｎｔｒｏｄｕｃｔｉｏｎＳｉｎｃｅｔｈｅｄｉｓｃｏｖｅｒｙｏｆｐｈｏｔｏｓｅｎｓｉｔｉｖｉｔｙｉｎｇｅｒｍａｎｏｓｉｌｉｃａｔｅｏｐｔｉｃａｌｆｉｂｅｒｓｂｙＨｉｌｅｔａｌ．ｉｎ１９７８［１］，ｓｉｇｎｉｆｉｃａｎｔｐｒｏｇｒｅｓｈａｓｂｅｅｎｍａ...     

用相位掩模法制作光纤光栅的技术

准分子激光照射相位掩模后,在近场形成周期的条纹分布,利用近场光强对光敏光纤进行曝光,可以在纤芯中写人光栅。对光纤光栅折射率分布进行合理假设,运用耦合模理论计算了光纤光栅的反射率,对其反射率与相关参数的关系进行了讨论,并且分析了用相位掩模技术制造光纤光栅的影响因素,得出要获得窄带宽高反射率光栅需有适当的折射率调制和大的光纤光栅长度的结论。另外还导出了掩模板后表面的近场光强分布和光纤光栅的周期公式。     

Theoretical analysis of novel fiber grating pair

A novel fiber grating pair that consists of a conventional long-period fiber grating and a fiber Bragg cladding grating (FBCG) is proposed. The FBCG is a new type of fiber grating in which refractive index modulation is formed in the cladding. Through the coupled-mode theory, we accurately calculate the coupling coefficients between modes supported in the fibers. And some other mode coupling features in the fiber cladding gratings are analyzed in detail. The calculation of the modes involved in this paper is based on a model of three-layer step-index fiber geometry. Then, we have investigated the sensitivity characteristics for variation of the modulation strengths of the fiber Bragg cladding gratings’ resonance peaks and the long-period cladding gratings’ (LPCGs) dual resonant peaks. Finally, the modulation strength sensitivity of the grating pair’s three resonant peaks is demonstrated, and the results indicate that these grating pairs may find potential applications in optical fiber sensing.     

金纳米颗粒掺杂光致聚合物的体全息混合光栅模型

金纳米颗粒掺杂光致聚合物在全息曝光过程中,光产物周期分布会形成折射率调制相位型主光栅,同时金纳米颗粒周期分布形成由局域表面等离子体共振引起强吸收的振幅型辅助光栅。研究基于耦合波理论的一种混合光栅模型,分析了光栅的体全息光学特性。结果表明,混合光栅中的折射率光栅和吸收光栅都能够提升体光栅的衍射效率; 体光栅的角度选择性也可以得到明显的改善。     

体全息成像系统中非周期体光栅的深度选择性研究

由一束球面波和一束平面波或者两束球面波干涉所形成的体全息光栅,由于其光栅矢量在全息图体积内是随位置的变化而变化的,所以被称为非周期型的体光栅。主要研究了用于体全息三维成像系统的非周期体光栅的深度选择特性。根据叠加的原理,将非周期体光栅看作多个固定周期的基元体光栅的叠加,结合耦合波理论分析非周期体光栅的衍射特性。采用这一方法,利用Matlab软件模拟,研究了两束记录光夹角对所记录的非周期体光栅深度选择性的影响和在两束记录光夹角相同时,球面参考光体全息成像系统及平面参考光体全息成像系统深度选择性的差别,最后在光折变晶体材料中进行非周期型和周期型体光栅的记录和再现,对模拟结果进行了实验验证。     

Nonlinear optical properties of composites based on conductive metal-alkanoate liquid crystals

The dynamic holography in new composite materials based on a novel class of metal-alkanoate ionic liquid crystals (ILCs) is studied experimentally and theoretically. The composites are formed as a dielectric dye film covered by lyotropic metal-alkanoate ILC and ionic smectic glasses with doped dye molecules. The dynamic gratings are created by nanosecond pulses of double frequency Nd:YAP laser, the recording demonstrates fast erasure time of residual thermal gratings. The nonlinear optical properties are determined by the resonance nonlinearity in photosensitive centres of ILC. Note, that permanent relief gratings will be formed on a dielectric dye film only as well as in composite cells either with nematic LC or with polymers under action of pulsed laser radiation. Lyotropic ILC layer applied over the dye film provides the dynamic regime of grating recording in composite cells. We found a secondary thermal grating is much smaller, the conductive ILC matrix provides effective heat dissipation and erasure of this thermal grating. A theory of Raman-Nath self-diffraction holography on thin films followed from the wave equation and the nonlinear mechanism of absorption saturation is developed to explain experimental results.     

Simultaneous diffraction of two finite waves at non-uniform dynamic volume reflection gratings

Based on the two-dimensional coupled-wave theory, the simultaneous diffraction of two finite waves with non-constant amplitude distribution at a finite non-uniform dynamic volume reflection grating is described. A coupled differential equation is derived and solved numerically with the aid of a two-dimensional Runge-Kutta method. The results for the chosen example of a planar volume reflection grating both for pure phase and absorption gratings show the dependence of the fidelity and diffraction efficiency on the normalized parameter grating strength, on the phase shift with respect to the interference pattern of the read-out waves and on the absorption modulation. In contrast to the transmission grating, a high fidelity of the enhanced beam can be achieved for reflection gratings. The numerical results are compared with the solution of the one-dimensional theory.     

记录方式对光致聚合物中全息光栅形成过程的影响

根据光致聚合物记录机理,研究了不同记录方式对光栅衍射效率的影响.对已有的光致聚合物光栅形成的一阶扩散模型进行简化,求解出全息曝光、暗增长、均匀后曝光过程对应的折射率调制度的解析式.应用所得解析结果,对三种记录方式在不同光强下的折射率调制度动态进行数值模拟.采用蓝敏光致聚合物,分别在4 mW/cm~2和2 mW/cm~2光强下应用不同方式记录光栅,结果表明:如果曝光光强较高,暗增长的记录方式将获得相对高的饱和折射率调制度,而均匀后曝光会加速达到饱和的进程.     

Observation of type I and type II gratings behavior in polymer optical fiber

We report the first observation of type I and type II fiber grating behaviors in making polymer optical fiber Bragg gratings. Our observation reveals that there are two distinctive stages in the fabrication of polymer optical fiber Bragg gratings. Notably the two stages of grating formation correspond to low and high-index modulation gratings, which match well with those in silica fiber grating fabrication. Thus we refer them as type I and type II polymer fiber gratings, following the same nomenclatures for different types of silica fiber gratings. In addition, the characteristics and formation mechanism for type I and type II polymer fiber gratings are also examined.     

Bragg grating resonances in all-solid bandgap fibers

Bragg gratings are fabricated in all-solid photonic bandgap fibers by forming a longitudinal periodic index modulation over the high-index rod lattice in the cladding. Due to its unique index-modulation pattern and the modal properties of the fiber, resonance couplings to the LP(01) supermodes (also known as high-index rod modes) are observed. The corresponding peak is located at the long-wavelength side of the Bragg wavelength and presents the highest depth. The asymmetric index profile over the high-index rods, which is induced by side UV illumination, leads to broadening of the supermode resonance peaks and variation with fiber orientation in the bend response of the fiber grating.     

Amplitude of the dynamic phase gratings in saturable Er-doped fibers

Dynamic population gratings recorded via local saturation of optical absorption/gain in rare-earth (Er, Yb) doped fibers demonstrate contributions of the amplitude and phase components. Quantitative comparison of the experimentally observed amplitude grating efficiency with that evaluated from spatially uniform saturation of the fiber optical absorption usually shows a significant discrepancy. The grating amplitude proves to be significantly weaker than its theoretical evaluation. The first results on quantitative comparison of the recorded phase grating amplitudes with spatially uniform photo-induced refractive index change in Er-doped fibers at three essentially different wavelengths (1485, 1526, and 1568 nm) are reported. As for the amplitude grating component, the experimentally observed phase grating amplitude is inferior to its theoretical evaluation; this discrepancy is spectrally dependent and is also significantly reduced in the short-wavelength region 1480–1490 nm on the Er³⁺ ion absorption.     

Frustration of Bragg reflection by cooperative dual-mode interference: a new mode of optical propagation

A new optical mode of propagation is described, which is the natural eigenmode (supermode) of a fiber (or any optical waveguide) with two cospatial periodic gratings. The mode frustrates the backward Bragg scattering from the grating by destructive interference of its two constituent submodes (which are eigenmodes of a uniform waveguide). It can be used in a new type of spatial mode conversion in optical guides.     

菌紫质同线偏振全息记录时再现光偏振方向对衍射效率的调制

当用相同偏振方向的物光和参考光在菌紫质薄膜上记录光栅时,再现光的偏振方向会影响其衍射效率.采用琼斯矩阵方法对此进行了理论分析,结果显示,再现光的偏振方向对衍射光的光强产生余弦调制;当再现光的偏振方向平行或垂直于记录光的偏振方向时,衍射光仍为线偏振光,其他情况下衍射光均变成椭圆偏振光.再现光偏振方向对衍射效率峰值的调制为正向余弦调制,对衍射效率稳定值的调制为反向余弦调制(与前者在相位上相差π).加入辅助紫光可抑制光栅的饱和,从而使得再现光偏振对衍射效率稳定值的调制由反向余弦调制变为正向余弦调制,并且提高了衍 关键词： 菌紫质 光致各向异性 衍射效率 琼斯矩阵     

振幅掩膜紫外写入的长周期光纤光栅特性研究

振幅掩膜紫外写入的长周期光纤光栅的纤芯折射率分布函数为矩形波。以三层阶跃折射率光波导结构基础，用弱导标量近似和标量耦合模理论分析折射率调制类型为矩形波的长周期光纤光栅的特性。详细地给出耦合模方程近似处理的方法，并说明了其合理性。用数学软件Matlab进行了数值模拟计算，发现折射率调制类为矩形波的光栅传输谱不是由它的各次余弦光栅谱的线性叠加而成的。还研究了外部环境折射率、包层半径、栅占空比等光栅结构参量对矩形折射率调制的光栅传输谱的影响。同时指出了每阶包层模的双谐振峰位置随栅参量的变化规律。刊■刊『_型，刿j1     

面向地壳形变观测的超高分辨率光纤应变传感系统

高分辨率光纤应变传感系统是地球物理学中地壳微弱形变观测的有力工具.相比于传统的地壳应变观测技术,光纤应变传感器具有测量分辨率高、抗干扰能力强、尺寸小、可复用、易于安装布设等特性,在建立新型地壳形变监测网络中具有很大的应用潜力.本文围绕面向地壳形变观测的纳应变级分辨率光纤应变传感器技术,阐述了应变传感原理与实现超高测量分辨率的机理,并详细介绍了扫频探测、Pound-Drever-Hall解调技术、边带探测、双回路锁定传感、传感器时分复用等技术及相应的传感器系统实现方案,最后,给出了超高分辨率光纤传感器在现场观测的实验结果与分析.