Adsorptive stripping voltammetric behaviour of copper complexes of some heterocyclic azo compounds

Controlled adsorptive accumulation of copper complexed with TAN, TAC, TAR and TAM (heterocyclic azo-compounds) on a static mercury drop electrode provides the basis for the direct stripping measurement of this element in the nanomolar concentration level. The ligand TAN exhibited great sensitivity and better separation of the peak current of the ligand in relation to the complex. The reduction current of adsorbed complex ions of copper is measured by linear scan cathodic stripping voltammetry, preceded by a period of accumulation of a few minutes. The peak potential is at approximately -0.37 V vs. Ag/AgCl. Optimal experimental parameters were found to be a TAN concentration of 1 x 10(-5)M, an accumulation potential of -0.22 V, and a solution pH of 3.7 (acetate buffer). The detection limit is 0.8nM after a 5-min accumulation with a stirred solution, and the response is linear up to 50 mug/l. Many common cations and anions do not interfere in the determination of copper. The interference of titanium is eliminated by addition of fluoride ion. Results are reported for a fresh water sample.     

Adsorptive stripping voltammetric behaviour of mitoxantrone on mercury electrodes

The electrochemical behaviour of mitoxantrone (MXT), an important antineoplastic agent, has been studied at mercury electrodes. The nature of the process taking place at the hanging mercury drop electrode (HMDE) was clarified. The electrochemical behaviour observed was in close agreement with theoretical predictions for an adsorbed molecule which is reversibly reduced. Both the molecule and its reduced product appeared to be adsorbed at the surface of the electrode. Adsorptive stripping voltammetry has been proven to be advantageous over any other assay technique, allowing 5 x 10(-11)M MXT to be detected. The interference arising from surfactants competing for the adsorption sites at the electrode have been studied and the possibility of MXT determination in dilute urine samples has been shown. Some interesting data, such as the MXT adsorbing surface area and the kinetic constant of the associated coupled chemistry reaction were also determined.     

Adsorptive stripping voltammetric determination of antimony

A new method is described for the determination of antimony based on the cathodic adsorptive stripping of Sb(III) complexed with 2′,3,4′,5,7-pentahydroxyflavone(morin) at a static mercury drop electrode (SMDE). The reduction current of the adsorbed antimony complex was measured by 1.5th-order derivative linear-sweep adsorption voltammetry. The peak potential is at −0.51 V (vs. SCE). The effects of various parameters on the response are discussed. The optimized analytical conditions were found to be: supporting electrolyte, chloroacetic acid (0.04 mol/l, pH 2.3); concentration of morin, 5×10⁻⁶ mol/l; accumulation potential, −0.25 V (vs. SCE); scan rate, 100 mV/s. The limit of detection and the linear range were 7×10⁻¹⁰ mol/l and 1.0×10⁻⁹3.0×10⁻⁷ mol/l Sb(III) for a 2-min accumulation time, respectively. This method has been applied to the determination of Sb(III) in steel and brass samples and satisfactory results were obtained. The adsorptive voltammetric characteristics and composition of the Sb(III)–morin complex were studied.     

Adsorptive stripping voltammetric determination of ofloxacin

The fluoroquinolone antibacterial agent ofloxacin was studied by adsorptive stripping voltammetry. Controlled interfecial accumulation of ofloxacin on a static mercury drop electrode in the hanging mercury drop mode provides high sensitivity. The linear concentration range was 0.079–197.5 μg ml^?1 when using a 60-s preconcentration at ?1 V vs. Ag/AgCl in Britton-Robinson buffer of pH 6.00. The detection limit of ofloxacin was 1 ng ml^?1. The precision is excellent with a relative standard deviation of ca. 0.75% at a concentration of 0.848 μg ml^?1.     

Adsorptive stripping square-wave voltammetric behavior of insulin

The adsorptive stripping voltammetric behavior of bovine insulin has been studied by both differential pulse and square-wave techniques, leading to analytical methodologies for its determination in aqueous samples and pharmaceutical preparations. The application of a square-wave mode for the stripping of adsorbed bovine insulin has proved to be much more sensitive, yielding signals 20 times larger than those obtained by applying a differential pulse scan. The precision obtained for the voltammetric method, at a concentration level as low as 0.77 mg L^–1 of the protein, was found to be 1.45% (RSD., n = 8) by SWS and 2.20% (RSD., n = 8) by DPS. The pharmaceutical product Actrapid containing biosynthetic human insulin was analyzed by both methods. Received: 25 February 1999 / Revised: 6 April 1999 / Accepted: 12 April 1999     

Adsorptive stripping square-wave voltammetric behavior of rofecoxib

Adsorption and reduction of rofecoxib were investigated by cyclic and square-wave voltammetry on a hanging mercury drop electrode in electrolytes of various pH values. The reduction process on hanging mercury drop electrodes gave rise to a single peak within the entire pH range (2.0-11.5). In alkaline solutions, rofecoxib gave a sensitive adsorptive reductive peak; approximately 10 times larger than those obtained by applying a square-wave scan without prior accumulation. Application of the method to the determination of rofecoxib in two pharmaceutical products (Vioxx 12.5 and 25 mg), without sample pretreatment, resulted in acceptable deviation from the stated concentrations.     

吸附转移溶出伏安法测定氟罗沙星注射液含量

氟罗沙星 (ｆｌｅｒｏｘａｃｉｎ ,ＦＬＲＸ)是一种抗菌谱广 ,杀菌力强的三氟喹诺酮类抗菌药[1] 。ＦＬＲＸ含量的测定方式主要有ＨＰＬＣ法[2 ,3] 、紫外分光光度法[3,4 ] 和荧光分光光度法[5] 。本文研究ＦＬＲＸ在不同支持电解质中的电化学行为 ,发现其在石墨电极表面有很强的吸附性 ,在一定的电位下富集几分钟 ,电极冲洗后在底液中扫描 ,仍有很大的峰电流。在此基础上建立了吸附转移溶出伏安法(ＡｄＴＳＶ) [6 ] 测定ＦＬＲＸ。方法的线性范围为 4～42 μｇ/ｍｌ,用于ＦＬＲＸ葡萄糖注射液中ＦＬＲＸ含量的测定 ,比其他方法灵敏、准确、…     

Adsorptive stripping square-wave voltammetric behavior of insulin

The adsorptive stripping voltammetric behavior of bovine insulin has been studied by both differential pulse and square-wave techniques, leading to analytical methodologies for its determination in aqueous samples and pharmaceutical preparations. The application of a square-wave mode for the stripping of adsorbed bovine insulin has proved to be much more sensitive, yielding signals 20 times larger than those obtained by applying a differential pulse scan. The precision obtained for the voltammetric method, at a concentration level as low as 0.77 mg L^–1 of the protein, was found to be 1.45% (RSD., n = 8) by SWS and 2.20% (RSD., n = 8) by DPS. The pharmaceutical product Actrapid containing biosynthetic human insulin was analyzed by both methods. Received: 25 February 1999 / Revised: 6 April 1999 / Accepted: 12 April 1999     

Adsorptive stripping voltammetric measurements of trace levels of uranium following chelation with mordant blue 9

The chelate of uranium with the azo dye Mordant Blue 9 is shown to be adsorbed and then reduced on the hanging mercury drop electrode. These properties have been exploited in developing a highly sensitive stripping voltammetric procedure for trace determination of uranium. With controlled adsorptive accumulation for 5 min, a detection limit near 2 x 10(-10)M uranium is obtained. Cyclic voltammetry has been used to characterize the interfacial and redox behaviour. The effect of various operational parameters on the stripping response is discussed. Experimental conditions include use of 1 x 10(-6)M Mordant Blue 9 in 0.05M acetate buffer (pH 6.5), an accumulation potential of -0.43 V, and a linear potential scan. The response is linear up to 1.2 x 10(-7)M uranium, and the relative standard deviation at 4.2 x 10(-8)M is 3.2%. The effects of possible interferences from organic surfactants or metal ions have been investigated.     

Adsorptive stripping voltammetric determination of chromium in gallium

The electroanalytical chemistry of trace metals has progressed strongly with the development of cathodic stripping voltammetry (CSV) preceded by adsorption collection of organic metal complexes. A sensitive method for the determination of trace amount of chromium in gallium is described. Gallium is dissolved in sodium hydroxide containing hydrogen peroxide. The method is based on the catalytic activity of nitrate ions on the reduction of Cr(III)TTHA (triethylene tetramine-N,N,N',N',N',N'-hexaacetic acid) complex. The sensitivity of this method is further improved by adsorption preconcentration of Cr(III)TTHA complex at a hanging mercury drop electrode (HMDE). The Cr(III) formed at the electrode surface by the reduction of Cr(VI), which is present in the bulk solution, is immediately complexed by TTHA. The adsorbed complex is then reduced at a peak potential of - 1.26 V, and the peak height of Cr(III) reduction is measured. The determination limit was restricted by the amount of chromium present in the reagent blank solution. The method is suitable for the determination of chromium at level as low as 0.2 mug g(-1) (with about 50 mg of sample) and a relative standard deviation of 15%.     

Adsorptive voltammetric behaviour of immunoglobulin M

The adsorptive voltammetric behaviour of immunoglobulin M (IgM) has been investigated at the static mercury drop electrode. The stripping process yields an analytically useful signal and the detection limit is 1.2 x 10(-10)M. The adsorptive voltammetric behaviour of IgM has been compared with that of IgG and streptavidin.     

Adsorptive stripping voltammetric determination of thiourea and thiourea derivatives

Adsorptive stripping voltammetry of thiourea, α-naphthylthiourea and diphenyl-thiourea is discussed. In perchlorate solution, these compounds are adsorbed at the hanging mercury drop electrode at positive potentials (or at open circuit) and can be stripped in a cathodic scan. Detection limits are 2.5 ng l^?1 for thiourea, 80 ng l^?1 for α-naphthylthiourea and 50 ng l^?4 for diphenylthiourea. The method is applicable in the determination of thiourea in cattle-feed and in the direct analysis of urine.     

Adsorptive stripping voltammetric properties of fentanyl at Hg electrode

Cyclic voltammetry shows that in a supporting electrolyte of NaOH, fentanyl (FENT) has a pair of cathodic and anodic peaks at Hg electrode. The peak potentials, E(pc) and E(pa), are -1.47 and -1.44 V (vs. Ag/AgCl), respectively. Fentanyl can be adsorbed on Hg surface, so the cathodic peak shows adsorptive properties. The adsorptive characteristics of fentanyl are explored in detail with various methods. The adsorbed species is considered to be fentanyl neutral molecule. The method for measuring trace amount of fentanyl by adsorptive stripping voltammetry is established. Under the optimised condition, the detection limit may reach 5 x 10(-8)M with a 10-min preconcentration.     

Adsorptive stripping voltammetric determination of vanadium as chloranilic acid complex

Traces of vanadium(V) can be determined up to 21 ng/l by adsorptive stripping voltammetry using 2,5-dichloro-1,4-dihydroxy-3,6-benzoquinone (chloranilic acid) as complex forming reagent. The complex is stable in a 0.1 mol/l acetate buffer (pH 4.6) solution and adsorbed at the electrode surface in a potential range between –150 mV and –400 mV. The adsorption process is solved by alternating current (ac) voltammetric measurements. The method is applied to different real samples.     

Adsorptive stripping voltammetric determination of pipemidic acid in human urine

The electrochemical behaviour of pipemidic acid (8-ethyl-5,8-dihydro-5-oxo-2-(1-piperazinyl)-pyrido[2,3-d]pyrimidine-6- carboxylic acid), a well known antimicrobial agent used for urinary infections, was investigated by linear-sweep, differential-pulse and square-wave voltammetry at a hanging mercury drop electrode. Two reduction processes were observed in Britton-Robinson buffers at acid pH, whereas only one or two processes were observed in alkaline solutions, dependent on the pH of the buffer employed. Adsorptive effects were used to accumulate the drug on to the electrode. The adsorbed species were measured voltammetrically by using a cathodic process appearing at -0.76 V in 0.1 M HCIO4. Linear calibration graphs were obtained in the range 2.5 x 10(-9)-2.0 x 10(-7) M. A simple procedure of extraction was employed for the determination of the drug in urine samples.     

Adsorptive stripping voltammetry of electroactive organic compounds

Adsorptive stripping voltammetry at a hanging mercury drop electrode is described for various polarographically active compounds. Diazepam, nitrazepam, papaverine and aromatic nitro compounds can be determined at concentrations of 1 × 10^?9–1 × 10^?6 M with errors of 5–7%. The effects of changing accumulation potentials and times are considered. Interference by other surface-active agents may be removed by prior molecular exclusion chromatography.     

Adsorptive stripping voltammetric determination of netilmicin in the presence of formaldehyde

A linear sweep adsorptive stripping voltammetric method for the determination of netilmicin in the presence of formaldehyde has been proposed for the first time. In the presence of 3.0×10⁻³ g ml⁻¹ formaldehyde, netilmicin exhibits a sensitive cathodic peak at −1.30 V (vs. the saturated calomel electrode, SCE) in a medium of Britton–Robinson buffer (pH 8.7) with a scan rate of 100 mV s⁻¹ after a preconcentration period of 120 s at −1.10 V (vs. SCE). The peak current showed a linear dependence on the netilmicin concentration over the range 4.2×10⁻⁹–1.0×10⁻⁷ g ml⁻¹. The achieved limits of detection and quantitation were 1.0×10⁻¹⁰ and 3.3×10⁻¹⁰ g ml⁻¹ netilmicin, respectively. It was deduced from the experiments that the amine–aldehyde condensation product formed between netilmicin and formaldehyde is mainly responsible for the appearance of the peak. The electrochemical behavior of netilmicin in the presence of formaldehyde has been studied. The method was applied to the direct determination of netilmicin in injectable formulations and spiked human urine and serum samples.      

Adsorptive stripping voltammetric determination of cobalt at ppb levels in high-purity aluminium

Summary A sensitive procedure for the determination of cobalt in high-purity aluminium using DPCSV through adsorptive accumulation of Co(DMG)₂ on HMDE in triethanolamine + NH₄OH buffer is described. Analysis of NBS SRM C-1257 and a reactor grade aluminium sample is reported. Prior to the determination, cobalt was separated from Al and Ni on AG-1 X8 resin in 9 mol/l HCl. The results have been cross-validated by INAA.     

Adsorptive stripping voltammetric determination of dimenhydrinate at a hanging mercury drop electrode

Dimenhydrinate exhibits a single adsorptive stripping peak at a hanging mercury drop electrode after accumulation at 0.0V vs Ag/AgCl electrode at pH 3.8 (acetate buffer). The addition of trace amounts of copper ions enhanced the dimenhydrinate peak and its height depends on the concentration of each dimenhydrinate and Cu²⁺. The adsorptive stripping response was evaluated with respect to accumulation time and potential, concentration dependence, electrolyte, the presence of other purines, surfactants and other metal ions, and some variables. The calibration graph for dimenhydrinate determination is linear over the range 2.0×10^–8–2.0×10^–7 M (pre-concentration for 60s). The correlation factor is found to be 0.985 and RSD is 3.2% at 1.0×10^–7 M. Detection limit is 1.0×10^–8 M after 5 min accumulation. The determination of dimenhydrinate in pharmaceutical formulations by the proposed method is also reported.     

Adsorptive stripping voltammetric determination of midazolam as a method for quality control

Controlled interfacial accumulation of the benzodiazepine midazolam at a hanging mercury drop electrode provides the basis for a highly sensitive and accurate adsorptive stripping voltammetric procedure. The response was linear in the range 1.9 × 10^?6? × 10^?9 M when using a 120-s preconcentration at ?0.45 V vs. Ag/AgCl in Britton-Robinson buffer of pH 5.00. In this range the relative standard deviation was between 1.21 and 1.62%. The applicability of the method to pharmaceutical preparations is discussed.