Determination of adenosine disodium triphosphate using prulifloxacin-terbium(III) as a fluorescence probe by spectrofluorimetry

A new spectrofluorimetric method is developed for determination of adenosine disodium triphosphate (ATP). The interactions between prulifloxacin (PUFX)–Tb³⁺ complex and adenosine disodium triphosphate has been studied by using UV–vis absorption and fluorescence spectra. Using prulifloxacin–Tb³⁺ as a fluorescence probe, under the optimum conditions, ATP can remarkably enhance the fluorescence intensity of the prulifloxacin–Tb³⁺ complex at λ = 545 nm and the enhanced fluorescence intensity is in proportion to the concentration of ATP. Optimum conditions for the determination of ATP were also investigated. The dynamic range for the determination of ATP is 4.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, and the detection limit (3 σ/k) is 1.7 × 10⁻⁸ mol L⁻¹. This method is simple, practical and relatively free interference from coexisting substances and can be successfully applied to determination of ATP in real pharmaceutical samples. The mechanism of fluorescence enhancement of prulifloxacin–Tb³⁺ complex by ATP was also discussed.     

Simultaneous determination of arsenic, antimony and selenium by gas-phase diode array molecular absorption spectrometry, after preconcentration in a cryogenic trap

This paper describes a method for the simultaneous determination of As(III), Sb(III) and Se(IV) by combining hydride generation and gas phase molecular absorption spectrometry. A system for continuous hydride generation has been designed and developed, based on the use of a double process of gas-liquid separation, and optimal compromise operation conditions for the three compounds have been found. After generation, the hydrides are collected in a liquid nitrogen cryogenic trap, and then evaporated and driven to the flow cell of a diode array spectrophotometer, in which the transient signals over the 190–250 nm wavelength interval are measured. Under the recommended conditions (sample flow: 35 ml min⁻¹, 0.5 M HCl; reductor flow: 4 ml min⁻¹ of 4% NaBH₄, solution) linear response ranges above 50 μg 1⁻¹ for As(III), 30 μg 1⁻¹ for Sb(III) and 200 μg 1⁻¹ for Se(IV) are obtained with detection limits of 22 μg 1⁻¹, 15 μg 1⁻¹ and 65 μg 1⁻¹, respectively. Multiwavelength linear regression equations were used for the simultaneous determination of the three elements in different synthetic samples, with good precision and accuracy and to study simultaneously the interference from different chemical species for the three compounds. Results were similar to those obtained by other techniques using hydride generation.     

Spectrophotometric method for determination of vanadium and its application to industrial, environmental, biological and soil samples

The very sensitive, fairly selective direct spectrophotometric method for the determination of trace amount of vanadium (V) with 1,5-diphenylcarbohydrazide (1,5-diphenylcarbazide) has been developed. 1,5-diphenylcarbohydrazide (DPCH) reacts in slightly acidic (0.0001–0.001 M H₂SO₄ or pH 4.0–5.5) 50% acetonic media with vanadium (V) to give a red–violet chelate which has an absorption maximum at 531 nm. The average molar absorption coefficient and Sandell’s sensitivity were found to be 4.23×10⁴ l mol⁻¹ cm⁻¹ and 10 ng cm⁻² of V^v, respectively. Linear calibration graph were obtained for 0.1–30 μg ml⁻¹ of V^v: the stoichiometric composition of the chelate is 1:3 (V: DPCH). The reaction is instantaneous and absorbance remain stable for 48 h. The interference from over 50 cations, anions and complexing agents has been studied at 1 μg ml⁻¹ of V^v. The method was successfully used in the determination of vanadium in several standard reference materials (alloys and steels), environmental waters (potable and polluted), biological samples (human blood and urine), soil samples, solution containing both vanadium (V) and vanadium (IV) and complex synthetic mixtures. The method has high precision and accuracy (s=±0.01 for 0.5 μg ml⁻¹).     

Fluorescence reaction and complexation equilibria between norfloxacin and aluminium (III) ion in chloride medium

Norfloxacin, 1-ethyl-6-fluoro-1,4-dihydro-4-oxo-7-(1-piperazinyl)-3-quinoline carboxylic acid (NORH), reacts with aluminium(III) ion forming the strongly fluorescent complex [Al(HNOR)]³⁺, in slightly acidic medium. The complex shows maximum emission at 440 nm with excitation at 320 nm. The fluorescence intensity is enhanced upon addition of 0.5% sodium dodecylsulphate. Fluorescence properties of the Al-NOR complex were used for the direct determination of trace amounts of NOR in serum. The linear dependence of fluorescence intensity on NOR concentration, at a NOR to Al concentration ratio of 1:10, was found in the concentration range 0.001–2 μg/ml NOR with a detection limit of 0.1 ng/ml. The ability of aluminium (III) ion to form complexes with NOR was investigated by titrations in 0.1 M LiCl medium, using a glass electrode, at 298 K, in the concentration range: 2 × 10⁻⁴ ≤ [Al] ≤ 8 × 10⁻⁴; 5 × 10⁻⁴ ≤ [NOR] ≤ 9 × 10⁻⁴ mol/dm³; 2.8 ≤ pH ≤ 8.3. The experimental data were explained by the following complexes and their respective stability constants, log(β ± σ): [Al(HNOR)], (14.60 ± 0.05); [Al(NOR)], (8.83 ± 0.08); [A1(OH)₃(NOR)], (−14.9 ± 0.1), as well as several pure hydrolytic complexes of A1³⁺. The structure of the [Al(HNOR)] complex is discussed, with respect to its fluorescence properties.     

Spectrofluorimetric determination of levofloxacin in tablets, human urine and serum

A spectrofluorimetric method to determine levofloxacin is proposed and applied to determine the substance in tablets and spiked human urine and serum. The fluorimetric method allow the determination of 20–3000 ng ml⁻¹ of levofloxacin in aqueous solution containing acetic acid–sodium acetate buffer (pH 4) with λ_exc=292 and λ_em=494 nm, respectively. Micelle enhanced fluorescence improves the sensibility and allows levofloxacin direct measurement in spiked Human serum (5 μg ml⁻¹) and urine (420 μg ml⁻¹), in 8 mM sodium dodecyl sulphate solutions at pH 5.     

A new flow-injection determination of glucose based on the redox reaction of hydroquinone with iron(III) in the presence of 1,10-phenanthroline

A new spectrophotometric flow-injection (FI) method is proposed for the determination of glucose based on the redox reaction of hydroquinone with iron(III). When a glucose solution containing quinone is passed through the immobilized glucose oxidase column introduced in FI system, quinone is reduced to hydroquinone by glucose. In the presence of 1,10-phenanthroline (phen), iron(III) is then quantitatively reduced by hydroquinone to iron(II) followed by the formation of iron(II)-phen complex (λ_max=510 nm). An FI peak observed at 510 nm corresponds to the concentration of glucose. The wide dynamic range for glucose was obtained in the range of 1×10⁻⁶–1×10⁻³ mol l⁻¹ at a sampling rate of 24 h⁻¹ and the detection limit (S/N=3) was 5×10⁻⁷ mol l⁻¹. Relative standard deviations were 0.78, 0.44 and 0.23% (n=5) for 5×10⁻⁶, 5×10⁻⁵ and 5×10⁻⁴ mol l⁻¹ of glucose, respectively. The proposed method was successfully applied to the determination of glucose in control blood sera, human blood plasma and wine.     

Correction of iron interface in the spectrophotometric flow injection catalytic determination of molybdenum in plants

Iron interference in the spectrophotometric catalytic determination of molybdenum based on the iodide-hydrogen peroxide reaction can be corrected by using sulphosalicylic acid as masking and color-forming reagent. The catalytic influence of iron ions is circumvented to the extent of about 90% and correction of any remaining iron ions is possible by monitoring the colored iron(III)-salicylate complex at 490 nm. In this way, iron is also determined. With the proposed system, molybdenum can be determined in plant and food digests within the 0–100 μg Mo 1⁻¹ range in the presence of up to 25 mg Fe 1⁻¹, at a sampling rate of about 50 determinations h⁻¹. The relative standard deviation of 10 consecutive measurements was estimated as < 2%. Results for samples were comparable with those obtained by graphite furnace atomic absorption spectrometry. In addition, recoveries within the range 94–100% were calculated.     

Spectrophotometric determination of maneb by ternary complex formation with PAR and CTAB

A rapid, simple, direct, and sensitive method has been developed for the determination of maneb (manganese ethylenebisdithiocarbamate) based on the formation of manganese-4-(2′-pyridylazo) resorcinol complex by a ligand displacement reaction, which is rendered water soluble by a cationic surfactant cetyltrimethylammonium bromide (CTAB) by the formation of an ion association complex. Beer's law is obeyed over the concentration range 0.08–2.4 μg/ml of the final solution at 500 nm in pH range 8–12. The molar absorptivity and Sandell's sensitivity are calculated to be 8.84 × 10⁴ l.mol⁻¹.cm⁻¹ and 0.003 μg/cm², respectively. The developed method has been applied to the determination of maneb in commercial formulations, synthetic mixture, grain samples and vegetables.     

Simultaneous potentiometric determination of ClO(3)(-)-ClO(2)(-) and ClO(3)(-)-HClO by flow injection analysis using Fe(III)-Fe(II) potential buffer

A rapid potentiometric flow injection technique for the simultaneous determination of oxychlorine species such as ClO₃⁻–ClO₂⁻ and ClO₃⁻–HClO has been developed, using both a redox electrode detector and a Fe(III)–Fe(II) potential buffer solution containing chloride. The analytical method is based on the detection of a large transient potential change of the redox electrode due to chlorine generated via the reaction of the oxychlorine species with chloride in the potential buffer solution. The sensitivities to HClO and ClO₂⁻ obtained by the transient potential change were enhanced 700–800-fold over that using an equilibrium potential. The detection limit of the present method for HClO and ClO₂⁻ is as low as 5×10⁻⁸ M with use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 0.5 M H₂SO₄. On the other hand, sensitivity to ClO₃⁻ was low when a potential buffer solution containing 0.5 M H₂SO₄ was used, but could be increased largely by increasing the acidity of the potential buffer. The detection limit for ClO₃⁻ was 2×10⁻⁶ M with the use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 9 M H₂SO₄. By utilizing the difference in reactivity of oxychlorine species with chloride in the potential buffer, a simultaneous determination method for a mixed solution of ClO₃⁻–ClO₂⁻ or ClO₃⁻–HClO was designed to detect, in a timely manner, a transient potential change with the use of two streams of potential buffers which contain different concentrations of sulfuric acid. Analytical concentration ranges of oxychlorine species were 2×10⁻⁵–2×10⁻⁴ M for ClO₃⁻, and 1×10⁻⁶–1×10⁻⁵ M for HClO and ClO₂⁻. The reproducibility of the present method was in the range 1.5–2.3%. The reaction mechanism for the transient potential change used in the present method is also discussed, based on the results of batchwise experiments. The simultaneous determination method was applied to the determination of oxychlorine species in a tap water sample, and was found to provide an analytical result for HClO, which was in good agreement with that obtained by the o-tolidine method and to provide a good recovery for ClO₃⁻ added to the sample.     

Synthesis, structure and non-linear optical property of a copper(II) thiocyanate three-dimensional supramolecular compound

A novel copper(II) thiocyanate complex [Cu(im)₂(NCS)₂] 1 (im=imidazole) has been prepared and characterized by spectroscopic analysis and crystallographic method. This supramolecular compound exhibits a three-dimensional solid state structure constituted by N–HS hydrogen bonds and π–π stacking interactions. The compound in DMF solutions has a very strong third-order non-linear optical (NLO) behavior with absorption coefficient and refractive index ₂=1.18×10⁻¹¹ mw⁻¹, n₂=−9.00×10⁻¹⁶ m²w⁻¹, respectively, and third-order NLO susceptibility χ⁽³⁾ of 7.00×10⁻¹⁰ esu.     

Catalytic flow injection determination of vanadium by oxidation of N-(3-sulfopropyl)-3,3',5,5'-tetramethylbenzidine using bromate

A catalytic flow-injection (FI) method was developed for the determination of 10⁻⁹ mol l⁻¹ levels of vanadium(IV, V). The method is based on the catalytic effect of vanadium(V) on oxidation of N-(3-sulfopropyl)-3,3′,5,5′-tetramethylbenzidine (TMBZ·PS) using bromate as oxidant to form a yellow dye (λ_max=460 nm). The use of 5-sulfosalicylic acid (SSA) as an activator enhanced the sensitivity of the method. The calibration graphs with a working range 0.05–8.0 ng ml⁻¹ were obtained for vanadium(V). Vanadium(IV) was also determined, being oxidized by bromate. The detection limit (signal/noise, S/N=3) was 0.01 ng ml⁻¹ (ca. 2×10⁻¹⁰ mol l⁻¹) vanadium. The relative standard deviations (R.S.D.) for 15 determinations of 0.5 ng ml⁻¹ vanadium, and for ten determinations of 0.1 and 1.0 ng ml⁻¹ vanadium were 0.41, 2.6 and 0.25%, respectively, with a sampling rate of 15 samples h⁻¹. The proposed method was successfully applied to the determination of vanadium in natural waters.     

Adsorptive stripping voltammetric determination of antimony

A new method is described for the determination of antimony based on the cathodic adsorptive stripping of Sb(III) complexed with 2′,3,4′,5,7-pentahydroxyflavone(morin) at a static mercury drop electrode (SMDE). The reduction current of the adsorbed antimony complex was measured by 1.5th-order derivative linear-sweep adsorption voltammetry. The peak potential is at −0.51 V (vs. SCE). The effects of various parameters on the response are discussed. The optimized analytical conditions were found to be: supporting electrolyte, chloroacetic acid (0.04 mol/l, pH 2.3); concentration of morin, 5×10⁻⁶ mol/l; accumulation potential, −0.25 V (vs. SCE); scan rate, 100 mV/s. The limit of detection and the linear range were 7×10⁻¹⁰ mol/l and 1.0×10⁻⁹3.0×10⁻⁷ mol/l Sb(III) for a 2-min accumulation time, respectively. This method has been applied to the determination of Sb(III) in steel and brass samples and satisfactory results were obtained. The adsorptive voltammetric characteristics and composition of the Sb(III)–morin complex were studied.     

On-line extraction-spectrophotometric determination of neostigmine in pharmaceuticals using double membrane phase separator and monovalent dyestuff

A simple, sensitive and rapid spectrophotometric method for the determination of neostigmine by flow injection analysis (FIA) coupled with an ion associate extraction has been developed. The three-line manifold was assembled. Neostigmine(200 μl) was injected into a distilled water stream and the pH was adjusted to 10 with a borate–phosphate buffer solution. Then, the stream was mixed with the ion-pairing tetrabromophenolphthalein ethylester (TBPEH)-1,2-dichloroethane solution. After phase separation with a double membrane phase separator, absorbance was measured at 610 nm. A linear calibration graph was obtained between 1×10⁻⁷ mol l⁻¹ and 5×10⁻⁷ mol l⁻¹ of neostigmine. Up to 48 samples h⁻¹ could be processed with a relative standard deviation (R.S.D.) of 0.5% (n=5) for 4×10⁻⁷ mol l⁻¹ neostigmine. The proposed system was applied to the simple, reproducible and rapid determination of neostigmine in commercial pharmaceuticals.     

Selective potentiometric determination of nitrite ion using a novel (4-sulphophenylazo-)1-naphthylamine membrane sensor

A novel polymeric membrane sensor sensitive to (4-sulphophenylazo-)1-naphthylamine (SPAN) based on the use of tris(bathophenanthroline) Ni(II)–SPAN ion pair as an ion exchanger in plasticised PVC membrane is described. The sensor exhibits a linear calibration plot with near-Nernstian anionic slope of −55.0±0.3 mV log[SPAN]⁻¹ over the concentration range 10⁻⁶–10⁻² mol l⁻¹ at pH 7. The sensor shows working range over the pH 6–8, response time of 20 s for 10⁻⁵ mol l⁻¹ and operational lifetime of 8 weeks. The sensor is used for quantification of micro quantities of nitrite ion by a prior conversion into the more lipophilic SPAN ion, which is measured with adequate sensitivity, and high selectivity using SPAN sensor. Validation of the method according to the quality assurance standards shows good performance characteristics. The sensor is satisfactory utilised for potentiometric determination of nitrite ion in wastewater samples and meat products. The results are favourably compared with data obtained using the standard spectrophotometric procedure involving the same reaction.     

Application of amperometric sol-gel biosensor to flow injection determination of glucose

A glucose biosensor with enzyme immobilised by sol–gel technology was constructed and evaluated. The glucose biosensor reported is based on encapsulated GOX within a sol–gel glass, prepared with 3-aminopropyltriethoxy silane, 2-(3,4-epoxycyclohexyl)-ethyltrimetoxy silane and HCl. A flow system incorporating the amperometric biosensor constructed was developed for the determination of glucose in the 1×10⁻⁴–5×10⁻³ mol l⁻¹ range with a precision of 1.5%. The results obtained for the analysis of electrolytic solution for iv administration and human serum samples showed good agreement between the proposed method and the reference procedure, with relative error <5%.     

Determination of iron(III) with salicylic acid by the fluorescence quenching method

The spectrofluorimetric determination of Fe³⁺ using salicylic acid as an emission reagent has been investigated by measuring the decrease of fluorescence intensity of salicylic acid due to the complexation of Fe³⁺–salicylic acid. An emission peak of salicylic acid, which is decreased linearly by addition of Fe³⁺, occurs at 409 nm in aqueous solution with excitation at 299 nm. The determination of the ferric ion is in the range 1×10⁻⁶–10×10⁻⁶ M Fe³⁺ (0.0558–0.558 μg/ml) and the detection limit is 5×10⁻⁸ M. The quenching effect of Fe³⁺ on the fluorescence intensity of salicylic acid may be considered on the basis of complexation between salicylic acid and Fe³⁺. The effects of foreign ions were investigated.     

Effect of presence of 18-crown-6 on the response of 1-pyrrolidine dicarbodithioate-based lead selective electrode

The lipophilic ammonium salt of 1-pyrrolidine dicarbodithioic acid (PCDT)[I] was introduced as a selective ionophore for a sensitive Pb-ion selective electrode. Also, the effect of immobilization of 18-crown-6 (CW), into the above membrane, on the electrode performance was discussed. The slope of the PCDT-based [I] electrode was (26–30 mV decade⁻¹), while it was (29-30 mV decade⁻¹) for (PCDT+CW)-based [II] electrode according to the doping time. The linear concentration ranges were (1×10⁻⁶–1×10⁻¹ M) and (5×10⁻⁵–1×10⁻¹ M) for electrode types [I] and [II] after one-day doping. The working pH ranges were (5.0–10.0) and (7.0–10.0) for electrode types [I] and [II], respectively. Most of the common cations were tested for the evaluation of the electrode selectivity with correlation to the ionic radii of the tested cations. Among them only Na⁺, Ag⁺ and Fe³⁺ were the real interference. Application of using the electrode for the determination of lead in lubrication oil samples was performed with RSD (0.86–1.03%). The obtained results were compared to those of an atomic absorption spectrophotometric method.     

Simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional ion-selective electrodes in series

An on-line automated system for the simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional calcium-selective and fluoride-selective membrane electrodes as sensors in series is described. Samples (30 μl) are injected into a TISAB II (pH=5.50) carrier solution as an ionic strength adjustment buffer. The sample-buffer zone formed is first channeled to a fluoride-selective membrane electrode and then via the calcium-selective membrane electrode to the reference electrodes. The system is suitable for the simultaneous on-site monitoring of calcium (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 1.94×10⁻⁶ mol l⁻¹ recovery 99.22%, RSD<0.5%) and fluoride (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 4.83×10⁻⁶ mol l⁻¹ recovery 98.63%, RSD=0.3%) at a sampling rate of 60 samples h⁻¹.     

Voltammetric determination of phytochelatins using copper solid amalgam electrode

Voltammetric determination of synthetically prepared phytochelatins (γ-Glu-Cys)₂Gly (PC₂) and (γ-Glu-Cys)₃Gly (PC₃) has been studied using new type of copper solid amalgam electrode. The determination, based on the formation of cuprous complexes in buffer pH 8.1, is suitable for concentrations of PC in the range 10–100 nmol l⁻¹. Reproducibility, employing electrochemical cleaning of the electrode surface, was statistically evaluated. The achieved limit of detection (2.1–2.6×10⁻⁹ mol l⁻¹ for DCV measurement) together with the robust character of the electrode offer its use for detection of PCs in separated extracts of real samples.     

Simultaneous derivative spectrophotometric determination of thorium and uranium in a micellar medium

Derivative photometric methods for trace analysis of Th(IV) and UO₂(II), and their simultaneous determination in mixtures using 5,8-dihydroxy-1,4-naphthoquinone in a micellar medium are reported. Molar absorptivity and Sandell's sensitivity of 1:2 Th(IV) and 1:1 UO₂(II) complexes at their λ_max, 614.5 nm and 637.0 nm are, 1.19 × 10⁴ 1/mol/cm and 1.12 × 10⁴ 1/mol/cm and 1.95 × 10⁻² μg/cm² and 2.13 × 10⁻² μg/cm² μg/cm², respectively. Calibration graph is linear over the range 9.28 × 10⁻²−18.56 μg/ml of Th(IV) and 9.52 × 10⁻²−19.04 μg/ml of UO₂(II). Though presence of Th(IV) and UO₂(II) causes interference in each others determination, 9.28 × 10⁻¹−9.28 μg/ml Th(IV) and 9.52 × 10⁻¹−9.52 μg/ml UO₂(II) when present together, can be simultaneously determined using derivative spectra.