Investigating the chain conformations of spin‐coated polymer thin films by ToF‐SIMS depth profiling

Thin films of bromine‐terminated poly(bisphenol A octane ether) (BA‐C10) were prepared using 1,2‐dichlorobenzene (ODCB) as the solvent. The organization of the chains in these amorphous polymer films was evaluated using time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) depth profiling. For the thin films, the bifunctional polymer chains were folded and anchored to the substrate via their two Br end groups and a polymer brush of chain loops was formed on the substrate. As the film thickness increased, polymer chains in a random coil conformation were found to reside on the top of the polymer brush. Depth profiling revealed that the polymer chains were densely packed at the interface. Moreover, the polymer films showed thermal stability, implying strong interactions between the end groups and the substrate. Copyright © 2015 John Wiley & Sons, Ltd.     

Understanding the crystallization process of a diketopyrrolopyrrole-based conjugated polymer in blend films

The film morphology of fullerene and diketopyrrolopyrrole-based conjugated polymers (PDPPs) blends largely influences the device performance in organic solar cells. It is critical to control the morphology of blend films, which usually requires investigations of the crystallization of PDPP-based thin films. Here, we study the influence of marginal solvent additive 1,2-dichlorobenzene (ODCB) and non-solvent additive 1,8-diiodooctane (DIO) on the crystallization of poly[2,5-bis(2-octyldodecyl)pyrrolo-[3,4-c]pyrrole-1,4(2H,5H)-dione-alt-2,2′: 5′,2″: 5″,2″′-quaterthiophene] (PDQT). The blends formed fibril structures in thin films, as revealed by transmission electron microscopy. The fibril density increased and the width decreased with the ODCB amount. The critical ODCB content to achieve constant fibril width is almost proportional to the concentration of PDQT. Higher ODCB content also results in higher fibril density in pure PDQT films. In contrast, the amount of DIO has a negligible influence on the fibril width and density of thin films. Moreover, novel dendritic fibrils were formed in PDQT films upon addition of ODCB. A model based on nucleation and growth is proposed to explain these findings. The heterogeneous nucleation was dominant with the presence of ODCB, while the homogeneous nucleation was prevailing when DIO was used. The results show that initial nucleation density and growth direction are key factors determining the fibril width.     

Synthesis of methyl‐substituted azobenzene–carbazole conjugated copolymers with photoinduced structural changes

Azobenzene switches its structure instantaneously by reversible trans‐to‐cis and cis‐to‐trans photoisomerization with light irradiations. Dynamic change in polymer structure is expected via introducing an azobenzene unit into the main chain. In this study, a set of methyl‐substituted azobenzene–carbazole conjugated copolymers is synthesized by the Suzuki–Miyaura coupling method. Introduction of methyl substituents to the azobenzene unit of the monomer, and polymerization in a high‐boiling solvent improve the molecular weight of the polymer. Decrease of effective conjugation length due to the twisted structure of the main chain allows progress of photoisomerization. The microstructure of the polymer was determined with grazing incidence X‐ray diffraction (GIXD) measurements using synchrotron radiation. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1756–1764     

Solution‐crystallization and related phenomena in 9,9‐dialkyl‐fluorene polymers. II. Influence of side‐chain structure

Solution‐crystallization is studied for two polyfluorene polymers possessing different side‐chain structures. Thermal analysis and temperature‐dependent optical spectroscopy are used to clarify the nature of the crystallization process, while X‐ray diffraction and scanning electron microscopy reveal important differences in the resulting microstructures. It is shown that the planar‐zigzag chain conformation termed the β‐phase, which is observed for certain linear‐side‐chain polyfluorenes, is necessary for the formation of so‐called polymer‐solvent compounds for these polymers. Introduction of alternating fluorene repeat units with branched side‐chains prevents formation of the β‐phase conformation and results in non‐solvated, i.e. melt‐crystallization‐type, polymer crystals. Unlike non‐solvated polymer crystals, for which the chain conformation is stabilized by its incorporation into a crystalline lattice, the β‐phase conformation is stabilized by complexation with solvent molecules and, therefore, its formation does not require specific inter‐chain interactions. The presented results clarify the fundamental differences between the β‐phase and other conformational/crystalline forms of polyfluorenes. © 2015 The Authors. Journal of Polymer Science Part B: Polymer Physics published by Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1492–1506     

Diketopyrrolopyrrole‐based polymer fibrils formation by changing molecular conformation during film formation

The microstructure of conjugated polymers film is strongly dependent on factors such as the conformation and the film formation processing. In this article, we show how to induce more planarization conformation of conjugated polymer backbone during film formation processing and finally leading to the fibrils formation of the cast film. The conjugated polymer we used is poly[[2,5‐bis(2‐octyldodecyl)‐2,3,5,6‐tetrahydro‐3,6‐dioxopyrrolo[3,4‐c]pyrrole‐1,4‐diyl]‐alt–[[2,2′‐(2,5‐thiophene)bis‐thieno[3,2‐b]thiophen]‐5,5′‐diyl]] (PDPPTT‐T). The main solvent is chloroform (CF), the aliphatic 1,8‐diiodooctane (DIO) is used as the additives, which has similar solubility parameter to the conjugated polymer side chain, is a bad solvent to the conjugated backbone and has a lower volatility than CF. Thus, during the film formation, chloroform was evaporated faster than the additive. After the chloroform evaporated completely, the side chain was still dissolved in the additive, which decreases the steric hindrance and improves planarization conformation of the conjugated backbone of PDPPTT‐T. Films processed using the aliphatic additives have fibrillar morphology while films cast from the CF solvent were featureless. TEM images reveal that the fibrils were about 30 nm in width and several hundred nanometers in length. The backbones of PDPPTT‐T were parallel to the long axis of fibrils. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1079–1086     

Solvent‐induced helical conformation observed from a conjugated polymer poly(N‐octylcarbazole ethylene)

The formation of a cylinder‐like helical conformation induced by solvation was observed from a conjugated polymer poly(N‐octylcarbazole ethylene). The polymer was synthesized by McMurry condensation using N‐octyl‐3,6‐diformylcarbazole as monomer, in which the alkylcarbazolyl group was functioned as a turn angle. IR analysis indicated that the double bond in the polymer chain mainly takes a cis‐ conformation. Computer simulation revealed that the polymer could form into a hollow tubular nano‐structure with a cavity of less than 1 nm in diameter by folding its strand. The helical conformation formed by solvent induction was further proved by the measurements of circular dichroism (CD) spectrum, specific rotatory power and fluorescent (FL) spectra. Copyright © 2006 John Wiley & Sons, Ltd.     

Para‐linked and meta‐linked cationic water‐soluble fluorene‐containing poly(aryleneethynylene)s: Conformational changes and their effects on iron–sulfur protein detection

Four para‐linked or meta‐linked cationic water‐soluble fluorene‐containing poly(aryleneethynylene)s (PAEs) were synthesized to investigate the solvent‐induced π‐stacked self‐assembly. These PAE backbones are composed of fluorenylene and phenylene units, which are alternatively linked by ethynylene bonds. UV–vis absorption and photoluminescence spectra were used to study their conformational changes as solvent was gradually changed from MeOH to H₂O. In pure water, with gradually increased meta‐phenylene content (0, 50, and 100%), they underwent a gradual transition process of conformation from disordered aggregate structure to helix structure, which was not compactly folded. Moreover, the polymer with an ammonium‐functionalized side chain on the meta‐phenylene unit appeared to adopt a more incompact or extended helix conformation than the corresponding one without this side chain. Furthermore, the conformational changes of these cationic PAEs in H₂O were used to study their effects on biological detection. Rubredoxin (Rd), a type of anionic iron–sulfur‐based electron transfer protein, was chosen to act as biological analyte in the fluorescence quenching experiments of these polymers. Preliminary results suggest that they all exhibit amplified fluorescence quenching, and that the polymer with more features of helix conformation tends to be quenched by Rd more efficiently. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5424–5437, 2006     

Influence of the Nanoscale Morphology on the Photovoltaic Properties of Fullerene/MEH-PPV Composites

The relation between morphology and photoelectric properties of PPV derivatives/fullerene composites forming bulk heterojunction solar cells has been investigated. The solvent used to spin cast the photoactive layers has a main influence on the quenching of the MEH-PPV fluorescence, which could be attributed to different dispersion abilities of C₆₀ in the polymer layer shown by AFM microscopy. Formation of large fullerene aggregates is observed at fullerene concentrations of the order of 10% leading to phase separation for composite layers processed in THF, whereas more dispersed distributions of fullerenes are observed in an aromatic solvent like ODCB which accounts for a more efficient luminescence quenching with increasing filler concentrations. However the improvement of the dissociation of photogenerated charge pairs is counterbalanced by a less efficient charge transport in the composite shown by lower short circuit currents probably due to unfavorable polymer chain arrangement in ODCB. Thin film processing conditions have been modified by the preparation of blends of solutions of the polymer in THF and fullerene in ODCB. The resulting spin casted layers show improved morphologies implying better dispersion of the fullerenes and increased short circuit currents. The improvement of the photovoltaic properties of the MEH-PPV/C₆₀ composites has been attributed to the nanosized fullerene domains formed upon phase separation.     

Investigating the Dynamic Viscoelasticity of Single Polymer Chains using Atomic Force Microscopy

In single‐molecule force spectroscopy (SMFS), many studies have focused on the elasticity and conformation of polymer chains, but little attention has been devoted to the dynamic properties of single polymer chains. In this study, we measured the energy dissipation and elastic properties of single polystyrene (PS) chains in toluene, methanol, and N,N‐dimethylformamide using a homemade piezo‐control and data acquisition system externally coupled to a commercial atomic force microscope (AFM), which provided more accurate information regarding the dynamic properties of the PS chains. We quantitatively measured the chain length‐dependent changes in the stiffness and viscosity of a single chain using a phenomenological model consistent with the theory of viscoelasticity for polymer chains in dilute solution. The effective viscosity of a polymer chain can be determined using the Kirkwood model, which is independent of the intrinsic viscosity of the solvent and dependent on the interaction between the polymer and solvent. The results indicated that the viscosity of a single PS chain is dominated by the interaction between the polymer and solvent. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1736–1743     

Morphology and Performance of Poly(2-methoxy-5-(20-ethyl-hexyloxy)-p-phenylenevinylene) (MEH-PPV)∶(6,6)-Phenyl-C61-butyric Acid Methyl Ester (PCBM) Based Polymer Solar Cells

Polymer solar cells were fabricated based on composite films of poly(2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenylenevinylene) (MEH‐PPV):fullerene derivative (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) with weight blend ratio of 1:3, 1:4 and 1:5, spin‐coated from chloroform (CF), chlorobenzene (CB), and o‐dichlorobenzene (ODCB) solutions, respectively. Photoinduced current and power conversion efficiency (PCE) of the devices show a dependence on the solvents. The solar cells have the highest PCE at 1:5 blend ratio. Transmission electron microscopy (TEM) morphology reveals that there are some voids in MEH‐PPV:PCBM films. The void number decreases with the solvent from CF to CB and ODCB. We found the voids are located at the bottom of the films through electron tomography technique by TEM and film bottom‐side morphology study by atomic force microscopy. The charge carrier transport efficiency and collection efficiency should decrease greatly due to the voids, and the more voids the film has, the more degree the efficiencies decrease. PCE of the solar cell prepared from CF is lower than that of the solar cells prepared from CB and ODCB. The void phenomenon of MEH‐PPV:PCBM based solar cell and method to investigate the void position provide an experimental evidence and research mentality to fabricate polymer solar cell with high performance.     

Conformational change,intrachain aggregation and photophysical properties of regioregular poly(3‐octylthiophene) in alkanes

This study explores the role of segmental solubility of regioregular poly(3‐octylthiophene) (rr‐P3OT) on chain organization and its photophysical properties. In good solvent chlorobenzene (CRB), rr‐P3OT chain adopts an extended conformation, allowing long conjugation length of π‐electrons. Cyclohexane is a good solvent for octyl side chain but a poor solvent for the thiophene backbone. The selective segmental interactions of rr‐P3OT with this solvent induce conformational change of the polymer. Addition of cyclohexane into the CRB solution leads to chain coiling, which in turn causes significant decrease of the conjugation length. Absorption and photoluminescence spectra of the rr‐P3OT in cyclohexane exhibit a blueshift of about 16 nm compared to those of the CRB solution. The change of chain conformation is also detectable by monitoring the variation of quantum yield upon increasing cyclohexane ratio. The quantum yield drops from 0.17 ± 0.01 to 0.11 ± 0.01 when the extended rr‐P3OT chain transforms into coiled conformation. Hexane is a nonsolvent for rr‐P3OT due to its relatively low solubility parameter. The addition of hexane into rr‐P3OT solution in cyclohexane forces dense packing of thiophene rings within the coiled chain. An intrachain aggregation occurs in this system, leading to the appearance of three distinct redshift peaks in absorption spectra and the drastic drop of quantum yield. Correlation between the growth of redshift peaks and the decrease of quantum yield is clearly observed. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1288–1297     

Synthesis and characterization of L‐leucine containing chiral vinyl monomer and its polymer,poly(2‐(methacryloyloxyamino)‐4‐methyl pentanoic acid)

A chiral monomer containing L ‐leucine as a pendant group was synthesized from methacryloyl chloride and L ‐leucine in presence of sodium hydroxide at 4 °C. The monomer was polymerized by free radical polymerization in propan‐2‐ol at 60 °C using 2,2′‐azobis isobutyronitrile (AIBN) as an initiator under nitrogen atmosphere. The polymer, poly(2‐(Methacryloyloxyamino)‐4‐methyl pentanoic acid) is thus obtained. The molecular weight of the polymer was determined to be: M_w is 6.9 × 10³ and M_n is 5.6 × 10³. The optical rotation of both chiral monomer and its polymer varies with the solvent polarity. The amplification of optical rotation due to transformation of monomer to polymer is associated with the ordered conformation of chiral monomer unit in the polymeric chain due to some secondary interactions like H‐bonding. The synthesized monomer and polymer exhibit intense Cotton effect at 220 nm. The conformation of the chain segments is sensitive to external stimuli, particularly the pH of the medium. In alkaline medium, the ordered chain conformation is destroyed resulting disordered random coils. The ordered coiling conformation is more firmly present on addition of HCl. The polymer exhibits swelling‐deswelling characteristics with the change of pH of the medium, which is reversible. The Cotton effect decreases linearly with the increase of temperature which is reversible on cooling. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2228–2242, 2009     

Synthesis,Characterisation and Electrical Properties of Supramolecular DNA‐Templated Polymer Nanowires of 2,5‐(Bis‐2‐thienyl)‐pyrrole

Supramolecular polymer nanowires have been prepared by using DNA‐templating of 2,5‐(bis‐2‐thienyl)‐pyrrole (TPT) by oxidation with FeCl₃ in a mixed aqueous/organic solvent system. Despite the reduced capacity for strong hydrogen bonding in polyTPT compared to other systems, such as polypyrrole, the templating proceeds well. FTIR spectroscopic studies confirm that the resulting material is not a simple mixture and that the two types of polymer interact. This is indicated by shifts in bands associated with both the phosphodiester backbone and the nucleobases. XPS studies further confirm the presence of DNA and TPT, as well as dopant Cl^? ions. Molecular dynamics simulations on a [{dA₂₄:dT₂₄}/{TPT}₄] model support these findings and indicate a non‐coplanar conformation for oligoTPT over much of the trajectory. AFM studies show that the resulting nanowires typically lie in the 7–8 nm diameter range and exhibit a smooth, continuous, morphology. Studies on the electrical properties of the prepared nanowires by using a combination of scanned conductance microscopy, conductive AFM and variable temperature two‐terminal I–V measurements show, that in contrast to similar DNA/polymer systems, the conductivity is markedly reduced compared to bulk material. The temperature dependence of the conductivity shows a simple Arrhenius behaviour consistent with the hopping models developed for redox polymers.     

Importance of domain purity in semi‐conducting polymer/insulating polymer blends transistors

Printed electronics is a rapidly developing field of research which covers any electronic devices or circuits that can be processed using direct printing techniques. Among those printing techniques, inkjet printing is a technique of increasing interest for organic field‐effect transistors (FETs) due to its fully data driven and direct patterning. In this work, the morphology of semi‐conducting polymer/insulating polymer blends from inkjet printing and their FET properties have been investigated. We attempted to optimize the morphology of the blends by the addition of a co‐solvent to the blend solution prior to film deposition. By varying the boiling temperature of the co‐solvent, blend films are fabricated with varying domain purity and different degree of semi‐conducting polymer ordering. The morphologies of all the as‐cast samples from inkjet printing and subsequently thermally annealed samples are characterized by grazing incidence wide angle x‐ray scattering and small angle neutron scattering. The results indicate that the sample where a low boiling temperature co‐solvent is used exhibits a lower degree of semi‐conducting polymer ordering and less pure domains, resulting in a decrease of hole mobility. The morphologies that are formed when high boiling temperature co‐solvent is used, however, give a higher degree of semi‐conducting polymer ordering along with higher domain purity, significantly improving hole mobility up to 1.44 cm² V^?1 s^?1 at V_DS = 40 V. More importantly, with thermal annealing, all the samples exhibit similar semi‐conducting polymer ordering and domain sizes while the domain purity significantly varies. This work is a unique example that demonstrates the importance of domain purity in the optimization of morphology and FET performance, which is previous unavailable. It also provides a novel process that can efficiently control the morphology of semi‐conducting polymer/insulating polymer mixtures during deposition to maximize FET performance from inkjet printing. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1760–1766     

Molecular conformation of syndiotactic polystyrene gel from octadecyl benzoate solution

The molecular chain conformation of the dried gel of syndiotactic polystyrene (sPS) in octadecyl benzoate solution was investigated. sPS gels form rapidly through solid-liquid phase separation. The obtained sPS chains are in the highly ordered all-trans TT skeletal conformation which is different from a twofold TTGG helical conformation that sPS assumes in normal solvents. The size of the solvent molecule is considered to play an important role in the formation of the conformation of sPS in solution.     

Solution‐crystallization and related phenomena in 9,9‐dialkyl‐fluorene polymers. I. Crystalline polymer‐solvent compound formation for poly(9,9‐dioctylfluorene)

Polymer‐solvent compound formation, occurring via co‐crystallization of polymer chains and selected small‐molecular species, is demonstrated for the conjugated polymer poly(9,9‐dioctylfluorene) (PFO) and a range of organic solvents. The resulting crystallization and gelation processes in PFO solutions are studied by differential scanning calorimetry, with X‐ray diffraction providing additional information on the resulting microstructure. It is shown that PFO‐solvent compounds comprise an ultra‐regular molecular‐level arrangement of the semiconducting polymer host and small‐molecular solvent guest. Crystals form following adoption of the planar‐zigzag β‐phase chain conformation, which, due to its geometry, creates periodic cavities that accommodate the ordered inclusion of solvent molecules of matching volume. The findings are formalized in terms of nonequilibrium temperature–composition phase diagrams. The potential applications of these compounds and the new functionalities that they might enable are also discussed. © 2015 The Authors. Journal of Polymer Science Part B: Polymer Physics published by Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1481–1491     

Microphase separation in solutions of crystallizable segmented polyurethane

At present time the level of microphase separation together with polymer nture is considered to be a main factor in determining the physico‐mechanical properties of polyurethane materials. The researches show that realization of a certain polymer structure and properties of polymer are defined by microstructure of polyurethane chain. The purpose of this work was to study physico‐chemical regularities between nucleation and growth of microphase aggregations in crystallizable segmented polyurethane compstions as a function of the phase state of the system during transferring from comon solvent to a selective solvent. Besides we investigated the architecture of macromolecules, associates and phase particles of segmented polyurethane (SPU) formed in different regions of the phase diagram.     

The self‐assembly over nano‐ to submicro‐length scales in water of a fluorescent julolidine‐labeled amphiphilic random terpolymer

A novel fluorescent‐labeled amphiphilic random terpolymer is synthesized by controlled radical polymerization of a fluorescent molecular rotor monomer, 2‐cyano‐2‐[4‐vinyl(1,1′‐biphenyl)‐4′‐yl]vinyljulolidine, a hydrophilic monomer, poly (ethylene glycol) methyl ether methacrylate, and a hydrophobic monomer, perfluorohexylethyl acrylate. Combined dynamic light scattering and fluorescence emission spectroscopy measurements are used to investigate its self‐assembly in water solution. Self‐assembled nanostructures with a hydrodynamic diameter size D_h of 4 ± 1 nm are detected due to the single‐chain folding of the terpolymer in unimer micelles. The fluorescence emission intensity of the terpolymer in water solution is found to be one order of magnitude higher than that in organic solvents, as a result of the preferential encapsulation of the julolidine co‐units in hydrophobic compartments of the unimer micelles. The temperature dependence of the self‐associative behavior of the amphiphilic terpolymer is also investigated and a critical temperature is identified at which a transition between single‐chain unimer micelles and multi‐chain aggregates (D_h = 400 ± 40 nm) reversibly takes place on heating–cooling cycles. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 797–804     

Cooperative Self‐Assembly‐Assisted Formation of Monodisperse Optically Active Spherical and Anisotropic Nanoparticles

We report a new method in which spontaneous self‐assembly is employed to synthesize monodisperse polymer nanoparticles with controlled size (<50 nm), shape, tunable functionality, and enhanced solvent and thermal stability. Cooperative noncovalent interactions, such as hydrogen bonding and aromatic π–π stacking, assist self‐assembly of amphiphilic macromolecules (polystyrene‐block‐polyvinylpyridine, PS? PVP) and structure directing agents (SDAs) to form both spherical and anisotropic solid polymer nanoparticles with SDAs residing in the particle core surrounded by the polymers. Through detailed investigations by scanning electron microscopy and transmission electron microscopy (TEM), we have rationalized nanoparticle morphology evolution and dependence on factors such as SDA concentration and PVP size. By keeping the PS chain size constant, the particle morphology progresses from continuous films to spherical particles, and on to cylindrical nanowires or rods with increasing the PVP chain size. The final nanoparticles are very stable and can be redispersed in common solvents to form homogenous solutions and thin films of ordered nanoparticle arrays through solvent evaporation processes. These nanoparticles exhibit tunable fluorescent colors (or emissions) depending on the choices of the central SDAs. Our method is simple and general without requiring complicated synthetic chemistry, stabilizing surfactants, or annealing procedures (e.g., temperature or solvent annealing), making scalable synthesis feasible.     

Conformation of Azobenzene‐Modified Poly(α‐L‐Glutamate) (AZOPLGA) in Thin Films: Solid State NMR Studies

Abstract

The conformations of azobenzene‐modified poly(α‐L‐glutamate)s (AZOPLGA) with a different degree of functionalization were examined by solid state ¹³C NMR. The polymer main chain conformations in AZOPLGA powders (precipitated from reaction system) changes from α‐helix to β‐sheet when the degree of functionalization increases from 12% to 56%. In addition, the solvent used for fabricating films plays an important role in organizing AZOPLGA backbones into characteristic conformation. For AZOPLGA56 (AZOPLGA with 56% of functionalization) cast films, the polymer backbones can assume conformations ranging from order state (β‐sheet) to random coil by changing the solvent for fabrication. In contrast, the effect of solvent on the conformation of AZOPLGA23 (AZOPLGA with 23% of functionalization) is not so significant. When compared with AZOPLGA23 powder (precipitated from reaction system), the helical conformation increases for AZOPLGA23 film cast from TFA. However, the fractions of α‐helix and β‐sheet conformation in AZOPLGA23 films (cast from DMF or pyridine) are nearly identical to that of AZOPLGA23 power. Moreover, even though the polymer backbones are random coil in AZOPLGA56 films when cast from TFA, some locally ordered domain can be observed. Lastly, the effect of the azo content appears to play a dominant role over the effect of solvents in directing the conformation of these polymers.