Preparation and thermal properties of thermoplastic poly(vinyl alcohol) complexes with boronic acids

Poly(vinyl alcohol) (PVA) was converted into melt flowable derivatives by complexation with a small amount of n-butyl boronic acid (BBA) and phenyl boronic acid (PBA) in dimethylsulfoxide (DMSO), and their thermal properties were examined from a viewpoint of the melt spinning of the complexes. It was found that (1) the melting temperature of the PVA–boronic acid complexes decreases and their degradation temperature increases with increasing the boronic acid content; (2) no gelation occurs for the PVA complexes with BBA and PBA in DMSO; (3) PBA gives a larger melting-temperature depression for PVA than BBA, but the spinnability of the complexes with BBA is much better than that with PBA; and (4) the melt-molded PVA complex fibers can be easily regenerated into PVA fibers with hot water. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3045–3050, 1998     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

Grafting reactions of vinyl acetate onto poly[(vinyl alcohol)-co-(vinyl acetate)]

The grafting preference of vinyl acetate onto the methine carbon of poly(vinyl alcohol) (PVOH) versus the acetate group of poly(vinyl acetate) (PVAc) was determined as part of an attempt to prepare novel branched PVOH from partially hydrolyzed PVAc. The results showed long chain grafting on the acetate groups of the PVAc units rather than the methine carbons of the PVOH or PVAc units. Decreasing the monomer or initiator concentration decreased the molecular weight of the graft copolymer formed. Of the initiators studied, ammonium persulfate gave the largest increase in copolymer molecular weight. Both hydrolysis and reacetylation combined with gel permeation chromatography (GPC) and ¹³C-NMR of the fully hydrolyzed material were used to estimate the number and location of grafts. © 1996 John Wiley & Sons, Inc.     

Preparation of antimicrobial poly(vinyl alcohol) nanofibers containing silver nanoparticles

Polyvinyl alcohol (PVA) nanofibers containing Ag nanoparticles were prepared by electrospinning PVA/silver nitrate (AgNO₃) aqueous solutions, followed by short heat treatment, and their antimicrobial activity was investigated for wound dressing applications. Since PVA is a water soluble and biocompatible polymer, it is one of the best materials for the preparation of wound dressing nanofibers. After heat treatment at 155 °C for 3 min, the PVA/AgNO₃ nanofibers became insoluble, while the Ag⁺ ions therein were reduced so as to produce a large number of Ag nanoparticles situated preferentially on their surface. The residual Ag⁺ ions were reduced by subsequent UV irradiation for 3 h. The average diameter of the Ag nanoparticles after the heat treatment was 5.9 nm and this value increased slightly to 6.3 nm after UV irradiation. It was found that most of the Ag⁺ ions were reduced by the simple heat treatment. The PVA nanofibers containing Ag nanoparticles showed very strong antimicrobial activity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2468–2474, 2006     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

Liquid-state transitions (T>T g) of poly(vinyl alcohol)

The two liquid state transitions,T _ll andT _ll, of non-crystalline, uncrosslinked poly(vinyl alcohol) were determined by differential scanning calorimetry.T _ll increased as the molecular weightM _n increased, whileT _ll remained almost constant. Crosslinking and crystallinity lead to disappearance of the transitionT _ll. The transitionT _ll was linked to mobility of whole chains, whereasT _ll was characteristic of segmental mobility.     

Solid‐state 13C and 129Xe NMR study of poly(vinyl alcohol) and poly(vinyl alcohol)/lactosilated chitosan gels

Dry and hydrated poly(vinyl alcohol) (PVA) gels with 55% (a‐PVA) and 61% (s‐PVA) syndiotacticity and related PVA/lactyl chitosan (LC) blends have been investigated with ¹²⁹Xe and cross‐polarization/magic‐angle‐spinning ¹³C NMR techniques. Although the dry gels exhibit two broad ¹²⁹Xe resonances in the slow‐to‐intermediate exchange limit, both hydrated gels show three resonances. The corresponding dry blends exhibit two signals, the chemical shifts and line widths of which change with respect to those of pure PVA, whereas one (a‐PVA/LC) or two (s‐PVA/LC) signals appear in the spectra of the hydrated blends. A comparative analysis of the data demonstrates that LC rearranges the domains of the polymeric matrix in both the dry and hydrated blends according to the syndiotacticity of the PVA chains. Information on the molecular motions of the amorphous and swollen polymeric domains in the kilohertz range has been obtained from an analysis of the spin‐lattice relaxation times. These data indicate that the dynamics and arrangement of the PVA chains in the gels are strongly affected by their tacticity and the addition of the copolymer LC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3123–3131, 2003     

New chemical hydrogels based on poly(vinyl alcohol)

The syntheses of two new types of chemical hydrogels based on poly(vinyl alcohol), PVA, are reported. Common to both synthetic routes is the preparation of a telechelic PVA (tel-PVA) obtained by periodate splitting of the vicinal diol units present in few percent along the chain. tel-PVA was then used as crosslinking agent with chitosan and PVA in two simple reactions in aqueous phase such as reductive alkylation of chitosan and acetalyzation of PVA. Both reactions yielded firm wall-to-wall networks showing marked differences in their swelling capability. © 1996 John Wiley & Sons, Inc.     

部分醇解聚乙烯醇接枝聚对二氧环己酮的合成与表征

制备了部分醇解的PVA(paPVA),将其与PDO在均相本体接枝聚合,通过对paPVA醇解度以及投料比的选择,得到了具有各种分子结构的接枝共聚物.通过一维核磁共振谱表征了聚合物的微观结构;采用TG、DSC等测试手段研究了接枝共聚物的热性能和结晶性能.     

Dissolution mechanism of semicrystalline poly(vinyl alcohol) in water

Changes occurring in the degree of crystallinity and lamellar thickness distribution of poly(vinyl alcohol) (PVA) samples during dissolution in water were investigated. PVA samples of three different molecular weights were crystallized by annealing at 90, 110, and 120°C. The initial degrees of crystallinity measured by differential scanning calorimetry (DSC) and by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) varied from 43 to 60% and the average lamellar thicknesses measured by DSC ranged from 50 to 400 Å. PVA dissolution was followed at 25, 35, and 45°C from 30 s up to 195 min. Lamellar thicknesses were determined as a function of dissolution time using DSC. There was an initial drastic decrease in the degree of crystallinity, which leveled off to a fairly constant value before reaching zero by the time the polymer dissolved completely. Increase in molecular weight led to lesser number of crystals, but with larger average lamellar thickness, which were more stable in the presence of water. Increase in crystallization temperature or decrease in dissolution temperature led to larger average lamellar thickness. Based on these findings, a dissolution mechanism involving unfolding of the polymer chains of the crystal was proposed. © 1996 John Wiley & Sons, Inc.     

Fully-biodegradable poly(3-hydroxybutyrate)/poly(vinyl alcohol) blend films with compositional gradient

Fully-biodegradable bacterial poly(3-hydroxybutyrate) (PHB)/chemosynthetic poly(vinyl alcohol) (PVA) blend films with compositional gradient from one surface to the other surface of the films were prepared by a dissolution-diffusion technique. Three kinds of PVA samples, high- and low-molecular weight atactic PVA and highly syndiotactic PVA (s-PVA), were used in order to investigate the effects of molecular weight and tactic structure on the generation of compositional gradient. The solution of PHB in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP), which is also a good solvent for PVA, was cast on the PVA film and then the solvent HFIP was evaporated. By selecting the optimum volume of solvent and the evaporation rate, the PHB/PVA blend film with compositional gradient was obtained. The formation of compositional gradient was confirmed by FT-IR microscopy and ATR-FT-IR analysis. The 50%/50% PHB/s-PVA blend film with a nearly ideal compositional gradient, that is, the composition of PHB (or PVA) in the film changing gradually from 100% at one surface to 0% at the other surface of the film was obtained by casting PHB/HFIP solution on to the s-PVA film. Positional dependence of the absorbance of C==O and OH stretching bands along the film thickness direction for the PHB/S-PVA cast films.     

Morphology of poly(vinyl alcohol) gels assuring the greatest significant drawability

Atactic poly(vinyl alcohol) (at-PVA) and syndiotactic poly(vinyl alcohol) (st. PVA) prepared by gelation/crystallization using dimethyl sulphoxide/water mixtures were drawn in a hot oven at 160 °C under nitrogen. The degrees of polymerization of at- and st-PVA were 2000 and 1980, respectively. The drawability of at- and st-PVA films was affected by the composition of the solvent mixture as well as by quenching temperature. The drawability of at- and st-PVA films prepared by using the solvent mixture containing 60% of dimethyl sulphoxide and 40% of water became more pronounced as the temperature of gelation/crystallization decreased and the draw ratio reached maximum value at –80 °C. Namely, the greatest significant drawability was the same condition for at- and st-PVA films in spite of the different stereo-regularity. Even in this common best condition for significant drawability, however, the morphological properties of swollen gels and of the resultant dry gel films are different each other, dependent upon the tacticity. For at-PVA, small-angle light scattering under Hv polarization condition could not be observed in the swollen gels and in the dry films when the solutions were quenched at temperatures <–10 °C. In contrast, for st-PVA, the X-type scattering pattern from swollen gels became clearer as the temperature decreased but the pattern became indistinct under drying process at ambient condition. On the other hand, the fibrillar textures within the at- and st-PVA dry films became finer and the orresponding crystallinity became lower as the temperature of gelation/crystallization decreased. Thus it turned out that the morphological properties of the swollen gels and of the dried films play an important role to assure the greatest significant drawability.     

Multifunctional properties of 3D printed poly(lactic acid)/graphene nanocomposites by fused deposition modeling

In this work, three-dimensional (3D) printing system based on fused deposition modeling (FDM) is used for the fabrication of conductive polymer nanocomposites. This technology consists in the additive multilayer deposition of polymeric nanocomposite based on poly(lactic acid) (PLA) and graphene by means of a in house made low-cost commercial bench-top 3D printer. Further, 3D printed PLA/graphene nanocomposites containing 10 wt% graphene in PLA matrix were characterized for their mechanical, electrical and electromagnetic induction shielding properties of the nanocomposite. Furthermore X-ray computed micro-tomography analyses showed that printed samples have good dimensional accuracy and are significantly closer to the predefined design and the results of scanning electron microscopy (SEM) printed samples showed a uniform dispersion of graphene in PLA matrix The proposed material has uniquely advantageous when implemented in 3D printed structures, because incorporation of multifunctional graphene has been shown to substantially improve the properties of the resulting nanocomposite.     

Silylation of poly(vinyl alcohol) with hexamethyldisilazane in liquid ammonia

Silylation of poly(vinyl alcohol) has been performed with hexamethyldisilazane in liquid ammonia in an autoclave. This novel procedure has the advantage that the educt, the reagent, and the product are soluble in ammonia, which works under homogeneous conditions. No salt like by-products are formed and no tedious purification of the product is necessary. The degree of silylation has been adjusted through the ratio of silylating agent to hydroxy groups. Random incorporation of trimethylsilyl groups was proven by the linear dependence of the glass transition temperature from the degree of silylation and the solubility of the partially silylated material. Quantitative investigation of the silylation reaction showed first-order kinetics for the initial and final stages of the reaction indicative of a reaction where k₁ > k₂ > k₃. © 1995 John Wiley & Sons, Inc.     

Improved mechanical properties of poly (vinyl alcohol) films with glycerol plasticizer by uniaxial drawing

In this work, the uniaxial stretching poly (vinyl alcohol) (PVA) films with glycerol as plasticizer were prepared to explore the influence of drawing temperature and drawing ratio. The structure and property were investigated with scanning electron microscope, wide‐angle X‐ray diffraction, X‐ray diffraction, differential scanning calorimetry, mechanical tests, etc. With the increase of stretching temperature, the melting and crystallization temperatures increased. The tensile strength and Young modulus of glycerol/PVA films increased first and then decreased; when the temperature was 80°C, the tensile strength and Young modulus reached to maximum values of 197.2 and 470 MPa, respectively. In addition, with the increase of draw ratio, the orientation degree of the PVA molecular chains increased, indicating the improved regularity of molecular chains. When the PVA films were stretched to 4 times, the tensile strength and Young modulus of the films reached 162 and 143 MPa, respectively, which were 4 and 1.3 times compared with those of unoriented films. These environmentally friendly PVA films with excellent mechanical properties would find wide applications in the industry such as packaging, coating, etc.     

Effect of poly(vinyl alcohol) fine particles as a novel biodegradable nucleating agent on the crystallization of poly(3‐hydroxybutyrate)

The effect of poly(vinyl alcohol)(PVA) fine particles as the nucleating agent on the crystallization behavior of bacterial poly(3‐hydroxybutyrate)(PHB) was studied using differential scanning calorimetry measurements and polarized light microscope observation. The results were compared with the effect of PVA conventionally blended with PHB. The PVA fine particles were found to be able to greatly enhance the crystallization of PHB, while the conventionally blended PVA extremely retarded the crystallization of PHB. The nucleating effect of PVA fine particles is almost comparable to that of the talc powder. Considering the biodegradability and biocompatibility of PVA, the usage of PVA particle as a nucleating agent provides marked benefits over the currently employed nonbiodegradable nucleating agents, such as talc and boron nitride. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44:1813–1820, 2006     

Raman spectral study of solid and dissolved poly(vinyl alcohol) and ethylene-vinyl alcohol copolymer

We have measured the Raman spectra of ethylene-vinyl alcohol copolymer (EVOH) and poly(vinyl alcohol) (PVOH). Spectra of 88% hydrolyzed PVOH were examined from the partially crystalline solid, from PVOH dissolved in both H₂O and D₂O, and from films precipitated from these solutions. The spectrum in H₂O differs from that of the starting material by disappearance of sharp bands having Raman shift values of 1146 and 1093 cm^?1, strengthening of a band near 915 cm^?1, decrease in frequency of bands at 480, 1356, and 1441 cm^?1, and increase in frequency of bands at 369, 413, 1023, 1371, and 2910 cm^?1. The spectrum of the film shows partial reversal of these trends. With D₂O as the solvent, the band shifts are slightly different from those listed above and new bands appear. These changes are indicative of loss of crystallinity, change in stereochemistry, and partial deuteration of hydroxyl during dissolution of this PVOH sample at room temperature. © 1994 John Wiley & Sons, Inc.     

Synthesis of isotactic star-shaped poly(vinyl alcohol)

Isotactic 6-armed star-shaped poly(vinyl alcohol) (PVA) with a narrow molecular weight distribution was successfully prepared by the living cationic polymerization of 6-armed star-shaped poly(tert-butyl vinyl ether) (PTBVE) and subsequent acidic ether cleavage. The PTBVE was synthesized using hexa(chloromethyl) melamine (HCMM) as a hexafunctional initiator and ZnI₂ or ZnCl₂ as an activator in toluene/MC (1/1 v/v) at −70 °C. A better living stability of PTBVE was obtained in the ZnCl₂ activator system. The number average molecular weight and the polydispersity index of the 6-armed star-shaped PTBVE polymerized with ZnCl₂ at −70 °C for 24 h were 156,000 g/mol and 1.47, respectively. The fraction of the mm sequence of the resulting PVA was 52%.     

States of water in poly(vinyl alcohol) derivative hydrogels

We studied the behavior of absorbed water in equilibrium‐swollen poly(vinyl alcohol) derivative hydrogels by differential scanning calorimetry (DSC), ¹H nuclear magnetic resonance, and wide‐angle X‐ray diffraction. By DSC, three types of water were detected, and their relative fractions were estimated. With this technique we also calculated the pore size for every sample. From the nonexponential decay of the spin–spin relaxation data, we distinguished two environmental states of the absorbed water in the samples. The relaxation times were determined. From these data, we calculated the fractions of each type of water for every hydrogel and related them to the degree of crosslinking. The X‐ray study indicated that the water absorbed in these hydrogels forms a single crystalline phase on cooling. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1462–1467, 2003