阳极氧化法制备二氧化钛纳米管阵列的研究

采用电化学阳极氧化法,将纯钛浸入HF酸水溶液,在钛基体表面原位构建高度有序的二氧化钛纳米管阵列,探讨阳极氧化电压、电解液浓度和电解液温度等对二氧化钛纳米管阵列尺寸和形貌的影响。通过SEM、XRD对二氧化钛纳米管阵列的结构特征进行表征,结果表明,不同的阳极氧化电压、电解液浓度和温度都将影响TiO2纳米管阵列的尺寸和形貌,在阳极氧化电压为20V,HF电解液浓度为0.5%t条件下,可制备出结构规整有序的TiO2纳米管阵列。     

阳极氧化条件对氧化钛纳米管阵列形貌及光催化性能的影响

以阳极氧化法制备了高度有序的TiO2纳米管阵列,采用扫描电镜观察了不同制备条件下得到的TiO2纳米管阵列的微观形貌,分别考察了电解时间、电压、电解液组成对TiO2纳米管阵列形貌的影响;此外,以酸性红3R染料作为标志物,测定了制得的TiO2纳米管阵列片的光催化性能.结果表明,以0.5%NH4F(质量分数)和乙二醇与水按体积比5∶1混合得到的溶液作为电解液,在15V电压下电解2h,得到的TiO2纳米管阵列的纳米管管径适中(60nm)、大小均一、排列整齐.所制备的TiO2纳米管阵列对染料的降解率显著优于纳米TiO2水溶胶的,且其光催化性能与形貌、电解时间及煅烧温度等密切相关.     

Co/N-doped carbon nanotube arrays grown on 2D MOFs-derived matrix for boosting the oxygen reduction reaction in alkaline and acidic media

The development of high-performance and cost-effective electrocatalysts towards oxygen reduction reaction(ORR) is of significant importance,but still challenging for the practical applications in related energy systems.ORR process typically suffers from sluggish kinetics,the exploration of ORR electrocatalyst thus requires elaborate design.Herein,an effective strategy is developed for growing Co/N-doped carbon nanotube arrays on 2D MOFs-derived matrix via the pyrolysis of Co/Zn metalorganic-framework(MOF) nanosheets.The Co/Zn-MOF nanosheets serve as both the self-template for the 2D carbonized framework morphology and C/N source for the in-situ growth of 1D N-doped carbon nanotubes.The constructed hie rarchical architecture effectively integrates the OD/1D Co nanoparticle/Ndoped carbon nanotube interface and 1D(nanotubes)/2D(nanosheets) junction into frameworks with highly exposed active surface,enhanced mass-transport kinetics and electrical conductivity.As a result,the designed composite exhibits superior ORR activity and durability in alkaline media as compared to commercial Pt/C.Particularly,it shows promising ORR performance with a half-wave potential of 0.78 V versus reversible hydrogen electrode and negligible activity attenuation after 5000 potential cycles in acidic electrolyte.The designed strategy can be extended to construct other MOFs-derived carbon matrixes with diverse hierarchical structures and provide an efficient avenue for searching highperformance electrocatalysts.     

溶剂热法制备磷掺杂碳纳米管作为氧气还原和氧气析出反应双功能电催化剂的研究

对氧气还原(ORR)和氧气析出(OER)反应都具有催化活性的双功能催化剂在金属-空气电池中起着关键作用.本文通过溶剂热反应,一步原位合成了磷掺杂碳纳米管(P-CNT).旋转环盘电极测试表明磷掺杂能够明显提高碳纳米管的催化活性,P-CNT在碱性电解质中对ORR和OER都具有优异的催化活性.P-CNT对ORR的催化还原为近4电子反应,可与商业催化剂Pt/C(20 wt%)相比;而其对OER的催化活性则高于Pt/C(20 wt%).此外,P-CNT的长期稳定性优于Pt/C(20 wt%).P-CNT对ORR和OER的高催化活性和稳定性主要归因于磷对碳的掺杂以及磷与碳间强的化学键合.     

Chiral-selective etching effects on carbon nanotube growth at edge carbon atoms

Chemical vapor deposition (CVD) utilizing metal cluster nanoparticle catalysts is commonly used to synthesize carbon nanotubes (CNT), with oxygen-containing species such as water or alcohol included in the feedstock for enhanced yield. However, the etching effect of these additives on the growth mechanism has rarely been investigated, despite evidence suggesting that etching potentially affects the chirality distribution of product CNTs. We used quantum chemical methods to study how water-based etchant radicals (OH and H) may enhance the chiral selectivity during CVD growth using CNT cap models. Chemical reactivities of the caps with the etchant radicals were evaluated using density functional theory (DFT). It was found that the reactivities on the cap edges correlate with the chirality of the caps. These results suggest that proper selection of etchant species can provide opportunities for selective chirality control of the product CNTs. © 2018 Wiley Periodicals, Inc.     

椅型碳纳米管吸附氧原子的密度泛函理论研究

利用密度泛函B3LYP对有限长扶手椅形单壁碳纳米管(3,3),(4,4)和(5,5)吸附O原子的几何结构、电子属性、反应能和红外光谱进行了系统地理论研究,获得了一些有意义的结果,主要包括如下4个方面:(1)2个O原子吸附在管外壁垂直于管轴的C—C键形成开环的轮烯结构,吸附在管内壁形成环氧结构;(2)O原子吸附在管外壁要比吸附在管内壁具有较大的能隙和吸附反应能;(3)与单壁碳纳米管管外壁吸附1个O原子相比,2个O原子吸附在管外壁具有较大的吸附反应能;(4)B3LYP得到的C—O伸缩振动频率与实验一致.     

在光催化还原CO2中具有高催化效率的八面体Cu2O修饰的TiO2纳米管

光催化还原CO2生成烃类燃料是一种可同时解决全球变暖和能源危机问题的最有效途径之一。尽管这方面的研究已经取得了一定的进展,但是整体的光催化转换效率还非常低。因此,需要发展更加高效的催化剂。由于半导体材料禁带宽度与太阳光谱相匹配,人们已经对其进行了广泛研究。其中TiO2因具有无毒、强氧化性以及良好的光学和电学性质等而成为最主要的研究对象。但是对于光催化还原CO2反应来说, TiO2仍存在很多不足,如只能吸收太阳光谱中的紫外光,光生载流子会快速结合,以及光生空穴的强氧化能力等,这些都限制了其光催化还原CO2的效率。采用窄禁带宽度半导体修饰TiO2是解决上述不足的有效途径之一。本文采用简单的电化学方法成功制备了一种由窄禁带半导体Cu2O修饰的TiO2纳米管(TNTs)的复合物,并运用扫描电子显微镜(SEM)、X射线衍射(XRD)以及X射线光电子能谱(XPS)表征了所制备复合物的形貌、化学组成和结晶度。表征结果显示,所制备的TiO2为整齐排列的纳米管阵列结构;复合物中的纳米颗粒为Cu2O;当电化学沉积Cu2O的时间为5 min时,得到的Cu2O纳米颗粒初步呈类八面体结构。随着沉积时间的增加, Cu2O颗粒尺寸增加,具有八面体结构。 XRD和XPS结果表明, TiO2纳米管为锐钛矿,八面体Cu2O纳米颗粒的主要暴露晶面为(111)面。我们还进一步研究了不同量Cu2O纳米颗粒修饰的TiO2纳米管复合物在可见光以及模拟太阳光下光催化还原CO2的能力。在可见光下,由于自身的禁带宽度,纯净的TiO2纳米管没有任何光催化还原CO2的能力;经过Cu2O纳米颗粒的修饰,复合物显现出明显的光催化还原CO2的能力,其中经过30 min Cu2O沉积的TNTs具有最高的光催化效率。在模拟太阳光下,经过15 min Cu2O沉积的TNTs具有最高的光催化效率。在所有光催化还原CO2过程中,主要碳氢产物为甲烷。为了深入地理解该复合体系在还原CO2中的高催化效率,我们对催化剂进行了进一步的表征。紫外-可见漫反射光谱表明, Cu2O八面体纳米颗粒的沉积将TNTs的吸收光谱拓展到了可见光区域,提高了复合物对太阳光的吸收能力。此外,我们还通过测试所制样品的光电流反应、荧光发射光谱以及电化学阻抗谱,研究了催化剂中光生电子和空穴的分离和迁移能力。结果表明,适量的Cu2O沉积提高了复合物对光的吸收能力,增加了光生载流子的数量,从而使更多的光生载流子参与光催化反应。综上,本文首次报道了八面体Cu2O纳米颗粒修饰TNTs复合物的光催化还原CO2的能力。在一定量的Cu2O纳米颗粒修饰下,该复合物在光催化还原CO2生成烃类反应中表现出高效性。经过一系列详细的表征和讨论,我们认为其高效性主要源于三个方面：(1) TNTs的管状结构为反应物的吸附提供了大量的活性位点,同时一维的管状结构更有利于光生载流子的运载,从而提高了电子和空穴的分离;(2) Cu2O纳米颗粒的修饰提高了催化剂对光的吸收,促进催化剂最大程度地利用太阳光;(3) TiO2和Cu2O之间导带以及价带位置的匹配,在减少光生载流子复合的同时也降低了TiO2价带上空穴的氧化能力,从而抑制了CO2还原产物的再氧化过程。     

Multiwalled carbon nanotubes microcolumn preconcentration and determination of gold in geological and water samples by flame atomic absorption spectrometry

The potential of multiwalled carbon nanotubes (MWNTs) as solid-phase extraction adsorbent for the separation and preconcentration of gold has been investigated. Gold could be adsorbed quantitatively on MWNTs in the pH range of 1–6, and then eluted completely with 2 mL of 3% thiourea in 1 mol L^− 1 HCl solution at a flow rate of 0.5 mL min^− 1. A new method using a microcolumn packed with MWNTs as sorbent has been developed for the preconcentration of trace amount of Au prior to its determination by flame atomic absorption spectrometry. Parameters influencing the preconcentration of Au, such as pH of the sample, sample flow rate and volume, elution solution and interfering ions, have been examined and optimized. Under the optimum experimental conditions, the detection limit of this method for Au was 0.15 µg L^− 1 with an enrichment factor of 75, and the relative standard deviation (R.S.D) was 3.1% at the 100 µg L^− 1 Au level. The method has been applied for the determination of trace amount of Au in geological and water samples with satisfactory results.     

胡椒碱在碳纳米管修饰电极上的电化学行为研究

研究了胡椒碱在碳纳米管修饰电极上的电化学行为,在pH为6.4的磷酸盐缓冲溶液中,胡椒碱在-1.12V(vs.SCE)处有一灵敏的还原峰.与裸电极相比,还原峰电位明显正移,峰电流显著增加,表明该修饰电极对胡椒碱的还原反应具有明显的催化作用.峰电流与胡椒碱的浓度在10-6～10-5mol/L范围内呈良好的线性关系(r=0.995),检出限为2.0×10-7mol/L.同时,计算了电荷转移数和扩散系数,考查了修饰电极的重现性,7次平行测量的RSD为4.96%.     

Effect of atomic oxygen irradiation on the structural and tribological characteristics of polytetrafluoroethylene and its composites

Based on the ground‐based simulation facility, the effects of atomic oxygen (AO) irradiation on the structural and tribological properties of pure polytetrafluoroethylene (PTFE) and carbon fiber and MoS₂‐filled PTFE composites were studied by scanning electron microscopy, X‐ray photoelectron spectroscopy, and a ball‐on‐disc tribometer. The results shown that AO irradiation had significant effects on the structural and tribological properties of pure PTFE, in which the surface morphologies, mass loss, friction coefficient, and wear rate had been changed greatly after AO irradiation. However, it was noticeable that the addition of carbon fiber and MoS₂ filler to PTFE could improve the AO resist capacity and tribological properties of PTFE composites significantly. Copyright © 2016 John Wiley & Sons, Ltd.     

碳纳米管/聚苯胺复合材料的制备及应用研究进展

碳纳米管/聚苯胺复合材料因其独特的电磁学、热力学和机械性能,在很多领域具有潜在应用价值.本文作者对近年来该复合材料的制备方法、性能及应用方面的研究进展进行了综述.     

去甲肾上腺素在多壁碳纳米管修饰玻碳电极上的电化学行为

动物体内的去甲肾上腺素(NE)含量变化反映了肢体神经系统植物交感神经的活动状况,在临床和基础研究中非常重要[1-3]。用化学修饰电极研究儿茶酚胺类神经递质的电化学行为以及对其进行测定是目前分析化学比较活跃的研究领域[4-6]。利用羧基化后的多壁碳纳米管(MWC-NT)对电极表面     

Enhancement in solubility and conductivity of polyaniline with lignosulfonate modified carbon nanotube

An organic solvent soluble and high electrical conductivity, for example, 55.43 S/cm, polyaniline (PANI), was synthesized by a novel method. In this two steps process, a noncovalent approach was initially developed by functionalization of multiwalled carbon nanotubes (MWNTs) using calcium lignosulfonate (LsCa) via self‐assembly to result MWNTs‐LsCa. Then, the MWNT‐LsCa was employed as a template to lead anilinium monomers directly aligned on the surface to start the polymerization of PANI. The noncovalent modification of MWNTs avoided their agglomeration effectively to allow them doped in PANI at the molecular level. The obtained novel PANI/MWNTs‐LsCa presented excellent solubility and high conductivity. The recorded scanning electron microscopy photographs revealed that the MWNTs‐LsCa was wrapped with PANI chains that caused the crystal orientation improvement. In this article, a related scheme on resulting in the high conductivity of PANI/MWNTs‐LsCa was showed and described. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2036–2046, 2009     

The nitrogen edge-doped effect on the static first hyperpolarizability of the supershort single-walled carbon nanotube

The nitrogen edge-doped effect on the structure, dipole moment, and first hyperpolarizability of the supershort single-walled carbon nanotube (5, 0) has been studied systematically. For the nitrogen edge-doped effect on the structure, the mean diameter on the nitrogen-doped side (D(u)) decreases as the number of doped-nitrogen (n) increases (4.044 (1) > 3.991 (2) > 3.941 (3) > 3.891 (4) > 3.844 A (5)). Significantly, the nitrogen edge-doped effects on the dipole moment and first hyperpolarizability are revealed for the first time and these new effects are dramatic for the supershort single-walled carbon nanotube (5, 0). Among the beta(0) values of these seven nitrogen-doped structures, the largest beta(0) (3155 au) is larger by almost 450 times than the very small beta(0) (7 au) of undoped structure (D(5h)). For nitrogen-doped structures, the order of the beta(0) values is 3155 (1) > 2677 (2A) approximately 2817 (2B) > 1465 (3A) approximately 1458 (3B) > 670 (4) > 254 au (5), which shows two interesting relationships between the beta(0) value and nitrogen-doped number: (1) the smaller the nitrogen-doped number, the larger the beta(0) value. (2) The structures with the same number of doped-nitrogen have almost the same beta(0) values (1465 for 3A and 1458 au for 3B). As for the frequency-dependent beta (-omega; omega, 0) and beta (-2omega; omega, omega), the dependence on the nitrogen-doped number (n) is similar to the case of static beta(0). For beta (-2omega; omega, omega) values at omega = 0.005 au are 3220 (1) > 2720 (2A) approximately = 2862 (2B) > 1480 (3A) approximately = 1477 (3B) > 676 (4) > 256 au (5). In addition, the important monotonic dependences of the beta value on the D(u) and electronic spatial extent are also observed. The new knowledge of influence the beta value will be beneficial to design high-performance nonlinear optical (NLO) materials.     

Iron oxide nanotube film formed on carbon steel for photoelectrochemical water splitting: effect of annealing temperature

Carbon steels (CSs) were anodized in an ethylene glycol solution containing 3 vol.% H₂O and 0.1 m NH₄F to coat with nanotube arrays film. The as anodized nanotube arrays film were annealed in argon atmosphere at various temperatures ranging from 250 to 550 °C for 4 h. The morphology and crystal phases of the film developed after annealing processes were examined using field emission scanning electron microscopy, X‐ray diffraction. Morphology transforms from nanobube arrays to nanotube bundles at 250 °C, to nanobube bundles with nanoflakes at 350 and 450 °C, to nanotube bundles with nanobelts at 550 °C. Amorphous transformed completely into maghemite at 350 °C and hematite with minor magnetite at 450 and 550 °C. Diffuse reflectance ultraviolet and visible spectra revealed iron oxide nanotube film annealed at 350 °C, or higher than 350 °C behaved tremendous absorbance ability in visible spectra range. Mott–Schottky analysis and linear scan voltammetry were performed in 1 m NaOH to show that iron oxide nanotube film annealed at 450 °C exhibited best charge carrier transfer ability upon illumination and superior photoelectrochemical properties compared with the films annealed at other temperatures. The film annealed at 450 °C displayed the photocurrent density of 0.13 mA cm^?2 at 0.2 V_Ag/AgCl, but the film annealed at other temperatures with the photocurrent densities of lower than 0.05 mA cm^?2 at 0.2 V_Ag/AgCl. The morphology and phase transform of iron oxide nanotube film at different annealing temperature results in the change of their photoelectrochemical properties. Copyright © 2016 John Wiley & Sons, Ltd.     

Enhancement of ethanol electrooxidation on plasmonic Au/TiO2 nanotube arrays

Novel electrocatalysts Au/TiO₂ nanotube arrays (Au/TiO₂NTs) were prepared by loading low-content(1.9 at.%) of Au nanoparticles (AuNPs) onto highly ordered TiO₂ nanotube arrays (TiO₂NTs). Ethanol electrooxidation indicates that visible-light (λ > 400 nm) irradiation can significantly enhance the activity as well as resistpoisoning of Au/TiO₂NTs electrocatalysts that are activated by plasmon resonance. Au/TiO₂NTs catalysts calcinated at 300 °C display the highest performance due to the strong synergistic interactions between TiO₂ and Au NPs. The combination of visible-light irradiation with a controllable potential offers a new strategyfor enhancing the performance of anodes in direct ethanol fuel cell (DEFC).     

Preparation of well-aligned carbon nanotubes/silicon nanowires core-sheath composite structure arrays in porous anodic aluminum oxide templates

The well-aligned carbon nanotubes (CNTs) arrays with opened ends were prepared in ordered pores of anodic aluminum oxide (AAO) template by the chemical vapor deposition (CVD) method. After then, silicon nanowires (SiNWs) were deposited in the hollow cavities of CNTs. By using this method, CNTs/SiNWs core-sheath composite structure arrays were synthesized successfully. Growing structures and physical properties of the CNTs/SiNWs composite structure arrays were analyzed and researched by the scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction spectrum (XRD), respectively. The field emission (FE) behavior of the CNTs/SiNWs composite structure arrays was studied based on Fowler-Nordheim tunneling mechanism and current-voltage (/-V) curve. And the photoluminescence (PL) was also characterized. Significantly, the CNTs/SiNWs core-sheath composite structure nanowire fabricated by AAO template method is characteristic of a metal/semiconductor (M/S) behavior and can be     

Investigation on the application of titania nanorod arrays to the determination of chemical oxygen demand

In the present paper, the TiO₂ nanorod arrays electrode was developed as a sensor for the determination of chemical oxygen demand (COD) based on a photoelectrochemical degradation principle. Effects of common parameters, such as applied potential, light intensity and pH on its analytical performance were investigated. Under the optimized conditions, the nanorod arrays electrode was successfully applied in the COD determination for both synthetic and real samples. In the COD determination, the proposed method can achieve a practical detection limit of 18.3 mg L⁻¹ and a linear range of 20–280 mg L⁻¹. Furthermore, the results obtained by the proposed method were well correlated with those obtained using the conventional (i.e., dichromate) COD determination method. The main advantages of this COD determination method were its simplicity, long term stability and environmental friendly (corrosive and toxic reagents not consumed). This work would open a new application area (COD determination) of the TiO₂ nanorod arrays.     

An enhanced electrocatalytic oxidation and determination of 2,4-dichlorophenol on multilayer deposited functionalized multi-walled carbon nanotube/Nafion composite film electrode

The voltammetric (CV and DPV) behavior of multi-walled carbon nanotube/Nafion composite coupled with a glassy carbon electrode was investigated for the determination of 2,4-dichlorophenol. The structural and morphological evaluation by XRD and FESEM revealed that the acid treated MWCNT retained their morphology without any structural change. The existence of the possible functional groups was investigated by FTIR and Raman spectroscopy. Compared to bare GCE, a significantly reduced interfacial charge transfer resistance was noticed for MWCNT/Nafion/GCE by electrochemical impedance spectroscopy (EIS). The use of Nafion not only contributed to the non-covalent functionalization of MWCNT, but also protected the electrode surface against the polymerization of phenoxy radicals forming a passivating film. For MWCNT/Nafion/GCE, the combination of anti-passivating ability and excellent catalytic properties resulted in the rapid and direct electrochemical determination of 2,4-DCP. Under optimal experimental conditions, the DPV responses for MWCNT/Nafion/GCE is linear over the 1–150 μmol/L range with a detection limit (S/N = 3) of 0.01 μmol/L. The presence of many interfering species had no influence on the signals of 2,4-DCP. The proposed sensor was successfully tested for the determination of 2,4-DCP in tap water samples and the recovery was in the range of 99.0–102.5%.     

Molecular dynamics simulation of anticancer drug delivery from carbon nanotube using metal nanowires

In this study, we have investigated delivery of cisplatin as the anticancer drug molecules in different carbon nanotubes (CNTs) in the gas phase using molecular dynamics simulation. We examined the shape and composition of the releasing agent by using the different nanowires and nanoclusters. We also investigated the doping effect on the drug delivery process using N-, Si, B-, and Fe-doped CNTs. Different thermodynamics, structural, and dynamical properties have been studied by using the pure and different doped CNTs in this study. Our results show that the doping of the CNT has significant effect on the rate of the drug releasing process regardless of the composition of the releasing agent. © 2019 Wiley Periodicals, Inc.