Synthesis and properties of blue light‐emitting,silicon‐containing,regio‐ and stereoregular conjugated polymers

This article concerns the hydrosilylation polyaddition of 1,4‐bis(dimethylsilyl)benzene ( 1 ) with 4,4′‐diethynylbiphenyl, 2,7‐diethynylfluorene ( 2b ), and 2,6‐diethynylnaphthalene with RhI(PPh₃)₃ catalyst. Trans‐rich polymers with weight‐average molecular weights (M_w's) ranging from 19,000 to 25,000 were obtained by polyaddition in o‐Cl₂C₆H₄ at 150–180 °C, whereas cis‐rich polymers with M_w's from 4300 to 34,000 were obtained in toluene at 0 °C–r.t. These polymers emitted blue light in 4–81% quantum yields. The cis polymers isomerized into trans polymers upon UV irradiation, whereas the trans polymers did not. The device having a layer of polymer trans‐ 3b obtained from 1 and 2b demonstrated electroluminescence without any dopant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2774–2783, 2004     

Solving the loss of orthogonality during the polyaddition of α‐azide‐ω‐alkyne monomers catalyzed by Cu(PPh3)3Br: Application to the synthesis of high‐molar mass polytriazoles

Polyaddition of an α‐azide‐ω‐alkyne monomer by Cu(PPh₃)₃Br catalyzed 1,3‐dipolar cycloaddition was thoroughly studied as a model system to investigate the orthogonality of this click chemistry process. Indeed, loss of chain‐end functionality and occurrence of side reactions have a tremendous impact on the molar mass of polymers obtained by step growth polymerization. Particularly, SEC, ¹H, and ³¹P NMR experiments have highlighted the occurrence of a Staudinger side‐reaction between azide chain‐ends and PPh₃ from the copper(I) catalyst that dramatically alters M_n of the resulting polytriazoles. A significant enhancement of M_n could be achieved by using an alternative catalyst and optimized experimental conditions, that is, dilution and reaction time. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2470–2476, 2010     

Cationic polymerizations of 2‐alkyloxazolines catalyzed by bismuth salts

Acidic bismuth salts, such as BiCl₃, BiBr₃, BiJ₃, and Bi‐triflate catalyzed the ring‐opening polymerization of 2‐methoxazoline (MOZ) in bulk at 100 °C, whereas less acidic salts such as Bi₂O₃ or Bi(III)acetate did not. Bi‐triflate‐catalyzed polymerizations of 2‐ethyloxazoline (EtOZ) were performed with variation of the monomer–catalyst ratio (M/C). It was found that the molecular weights were independent of the M/C ratio. The formation of cationic chain ends and the absence of cycles was proven by reactions of virgin polymerization products with N,N‐dimethyl‐4‐aminopyridine or triphenylphosphine. The resulting polymers having modified cationic chain ends were characterized by ¹H NMR spectroscopy and MALDI‐TOF mass spectrometry. The polymerization mechanism including chain‐transfer reactions is discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4777–4784, 2008     

Influence of fluorinated substituent and terminal length on phase behavior of mesogen‐jacketed liquid crystalline polymers with a biphenyl mesogen

A series of mesogen‐jacketed liquid crystalline polymers, poly{2,2,3,3,4,4,4‐heptafluorobutyl 4′‐hydroxy‐2‐vinylbiphenyl‐4‐carboxylate} (PF3Cm, where m is the number of carbon atoms in the alkoxy groups, and m = 1, 4, 6, and 8), the side chain of which contains a biphenyl core with a fluorocarbon substituent at one end and an alkoxy unit of varying length on the other end, were designed and successfully synthesized via atom transfer radical polymerization. For comparison, poly{butyl 4′‐hydroxy‐2‐vinylbiphenyl‐4‐carboxylate} (PC4Cm), similar to PF3Cm but with a butyl group instead of the fluorocarbon substituent, was also prepared. Differential scanning calorimetric results reveal that the glass transition temperatures (T_gs) of the two series of polymers decrease as m increases and T_gs of the fluorocarbon‐substituted polymers are higher than those of the corresponding butyl‐substituted polymers. Wide‐angle X‐ray diffraction measurements show that the mesophase structures of these polymers are dependent on the number of the carbon atoms in the fluorocarbon substituent and the property of the other terminal substituent. Polymers with fluorocarbon substituents enter into columnar nematic phases when m ≥ 4, whereas the polymer PF3C1 exhibits no liquid crystallinity. For polymers with butyl substituents, columnar nematic phases form when the number of carbon atoms at both ends of the side chain is not equal at high temperatures and disappear after the polymers are cooled to ambient temperature. However, when the polymer has the same number of carbon atoms at both ends of the side chain, a hexagonal columnar phase develops, and this phase remains after the polymer is cooled. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Polymerization of 2‐pentene with Ni(II) α‐diimine complex/M‐MAO catalyst and structure of the polymer

Polymerization of 2‐pentene with [ArN?C(An)C(An)·NAr)NiBr₂ (Ar?2,6‐iPr₂C₆H₃)] ( 1‐Ni) /M‐MAO catalyst was investigated. A reactivity between trans‐2‐pentene and cis‐2‐pentene on the polymerization was quite different, and trans‐2‐pentene polymerized with 1‐Ni /M‐MAO catalyst to give a high molecular weight polymer. On the other hand, the polymerization of cis‐2‐butene with 1‐Ni /M‐MAO catalyst did not give any polymeric products. In the polymerization of mixture of trans‐ and cis‐2‐pentene with 1‐Ni /M‐MAO catalyst, the M_n of the polymer increased with an increase of the polymer yields. However, the relationship between polymer yield and the M_n of the polymer did not give a strict straight line, and the M_w/M_n also increased with increasing polymer yield. This suggests that side reactions were induced during the polymerization. The structures of the polymer obtained from the polymerization of 2‐ pentene with 1‐Ni /M‐MAO catalyst consists of ? CH₂? CH₂? CH(CH₂CH₃)? , ? CH₂? CH₂? CH₂? CH(CH₃)? , ? CH₂? CH(CH₂CH₂CH₃)? , and methylene sequence ? (CH₂)_n? (n ≥ 5) units, which is related to the chain walking mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2858–2863, 2008     

Synthesis of Structurally Well‐Defined Telechelic Polymers by Organostibine‐Mediated Living Radical Polymerization: In Situ Generation of Functionalized Chain‐Transfer Agents and Selective ω‐End‐Group Transformations

Several organostibine chain‐transfer agents possessing polar functional groups have been prepared by the reactions of azo initiators and tetramethyldistibine ( 1 ). Carbon‐centered radicals thermally generated from the azo initiators were trapped by 1 to yield the corresponding organostibine chain‐transfer agents. The high yields observed in the synthesis of the chain‐transfer agents strongly suggest that distibines have excellent radicophilic reactivity. As the reactions proceeded under neutral conditions, functional groups that are incompatible with ionic conditions were incorporated into the chain‐transfer agents. The chain‐transfer agents were used in living radical polymerization to synthesize the corresponding α‐functionalized polymers. As the functional groups in the chain‐transfer agents did not interfere with the polymerization reaction, well‐controlled polymers possessing number‐average molecular weights (M_ns) predetermined by the monomer/transfer agent ratios were synthesized with low polydispersity indices (PDIs). The organostibanyl ω‐polymer ends were transformed into a number of different functional groups by radical‐coupling, radical‐addition, and oxidation reactions. Therefore, it was possible to synthesize well‐controlled telechelic polymers with the same and also with different functional groups at their α‐ and ω‐polymer ends. Distibine 1 was also found to increase PDI control in the living radical polymerization of styrene and methyl methacrylate (MMA) using a purified organostibine chain‐transfer agent. Well‐controlled poly(methyl methacrylate)s with M_n values ranging from 10 000 to 120 000 with low PDIs (1.05–1.15) were synthesized by the addition of a catalytic amount of 1 . The results have been attributed to the high reactivity of distibine 1 towards polymer‐end radicals, which are spontaneously deactivated to yield organostibine dormant species.     

Selective nucleophilic additions to poly(methacrylate)s containing isothiocyanate moieties in the side chains and their application in cross‐linking

Reactivity of isothiocynate moieties in the side chain of polymethacrylate with amine, alcohol, or thiol was investigated, and the reactions were applied to preparation of networked polymers. Isothiocyanate of polymer side chain rapidly reacted with amines without a catalyst, to give the corresponding thioureas. However, it did not react with alcohols or thiols under the same conditions. Using 1,8‐diazabicyclo[5.4.0]undec‐7‐ene (DBU) as a catalyst, addition of alcohols or thiols to the isothiocyanate proceeded smoothly. Addition of amines, alcohols, and thiols to isothiocyanates moiety contained in the side chain of polymethacrylate also proceeded readily with or without the catalyst, respectively, to effectively give the corresponding side chain modified polymers. Occurrence of these additions was confirmed by ¹H NMR and IR measurements. Glass transition temperatures and thermal decomposition temperatures of the obtained polymers were investigated by differential scanning calorimetry and thermogravimetric analysis. Networked polymers were easily prepared by addition of 1,6‐hexamethylenediamine or hexamethylene glycol to the polymethacrylate having isothiocyanato groups. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1832–1842     

Synthesis of macrocycles by the ring‐crossover reaction of a cyclic dithioester

The ring‐crossover polymerization of cyclic dithioester 1 was performed in the presence of quaternary onium salts as catalysts at 70–150 °C for 24 h in NMP. It was found that predictable cyclic polymers with the same repeating structures as 1 were obtained with M_ns in the range between 700 and 3,500, quantitatively. It was observed that intermolecular and intramolecular thioester‐exchange reactions proceeded between cyclic monomer 1 and resulting cyclic polymers under thermodynamic control to give a lower‐molecular‐weight cyclic polymer with a lower polydispersity ratio (M_n = 2,400, M_w/M_n = 1.70). © 2006Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 680–687, 2007     

Controlling grafting density and side chain length in poly(n‐butyl acrylate) by ATRP copolymerization of macromonomers

Atom transfer radical polymerization (ATRP) was used for the preparation and subsequent copolymerization of two acryloyl‐terminated poly(n‐butyl acrylate) macromonomers with different degrees of polymerization (DP_nBA = 25 and 42). Homopolymerization of the higher molecular weight macromonomer ( MM1 ; PnBA₄₂‐A, M_n = 5600, DP_MM = 42, M_w/M_n = 1.18) resulted in preparation of a densely grafted polymer with a narrow molecular weight distribution (M_w/M_n = 1.14), but with the limited degree of polymerization DP = 12. The ultimate degree of homopolymerization for the lower molecular weight macromonomer ( MM2 ; PnBA₂₅‐A, M_n = 3400, DP_MM = 25, M_w/M_n = 1.20) was higher, and DP increased from 12 to 22. The limited DP could be because of progressively increasing steric congestion for macromonomers in approaching the growing chain ends of densely grafted polymers. When MMs were copolymerized with nBA, the reactivity of MM was nearly the same as that of nBA monomer irrespective of the differences in the degree of polymerization of the MMs and the initial molar ratio of nBA to MM. Well‐defined graft polymers with different lengths of backbone and side chains, and different graft density were successfully prepared by “grafting through” ATRP. Tadpole‐shaped and dumbbell‐shaped graft polymers were also synthesized by ATRP. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5454–5467, 2006     

Effect of polymer architecture on self‐diffusion of LC polymers

Two LC side‐group poly(methacrylates) were synthesized, and their melt dynamics were compared with each other and a third, main‐chain side‐group combined LC polymer. A new route was developed for the synthesis of the poly(methacrylate) polymers which readily converts relatively inexpensive perdeuteromethyl methacrylate to other methacrylate monomers. Self‐diffusion data was obtained through the use of forward recoil spectrometry, while modulus and viscosity data were measured using rotational rheometers in oscillatory shear. Diffusion coefficients and complex viscosity were compared to previous experiments on liquid crystal polymers of similar architecture to determine the effect of side‐group interdigitation and chain packing on center of mass movement. The decyl terminated LC side‐group polymer possessed an interdigitated smectic phase and a sharp discontinuity in the self‐diffusion behavior at the clearing transition. In contrast, the self‐diffusion behavior of the methyl terminated LC side‐group polymer, which possessed head‐to‐head side‐group packing, was seemingly unaffected by the smectic–nematic and nematic–isotropic phase transitions. The self‐diffusion coefficients of both polymers were relatively insensitive to the apparent glass transition. The presence of moderately fast sub‐T_g chain motion was supported by rheological measurements that provided further evidence of considerable molecular motion below T_g. The complex phase behavior of the combined main‐chain side‐group polymer heavily influenced both the self‐diffusion and rheological behavior. Differences between the self‐diffusion and viscosity data of the main‐chain side‐group polymer could be interpreted in terms of the defect structure. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 405–414, 1999     

Telechelic polynorbornenes with hydrogen bonding moieties by direct end capping of living chains

We present two novel symmetric olefins bearing hydrogen bonding moieties for the direct capping of living ring opening metathesis polymerization‐chains using Grubbs catalyst 1st‐ and 3rd‐generation. The symmetric olefins are generated via homo metathesis of the corresponding α‐olefins under aid of microwave irradiation and are used to prepare polynorbornene‐chains (M_n = 4,000–10,000 g/mol, M_w/M_n = 1.1–1.4) bearing barbiturate and thymine‐moieties. A qualitative and quantitative analysis of the generated polymers is done via MALDI‐TOF MS proving the introduction of hydrogen‐bonding moieties into the polymer chain and revealing the strong dependence of the desorption on the chemical structure of the different polymer species and high efficiencies for the end group introduction (90–99%). The efficiency of this process depends strongly on the reaction time and the equivalents of terminating agent with respect to the living end. The best results for the end group introduction are achieved by reacting the living chains with an excess of the terminating agent (5–20 equiv) for 100 h. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of π‐conjugated copolymers composed of benzo[2,1,3]thiadiazole and thiophene units bearing various alkyl groups and their application to photovoltaic cells

π‐Conjugated polymers, PTOTBT , PTEHTBT , and PTt‐BTBT , composed of benzothiadiazole as an electron accepting unit and terthiophene as an electron donating unit in the backbone were prepared. PTOTBT , PTEHTBT , and PTt‐BTBT contained side chain groups of n‐octyl, 2‐ethylhexyl, and t‐butyl groups, respectively. Solubility, optical and thermal properties of the polymers showed strong dependences on their side chain groups. PTEHTBT having 2‐ethylhexyl groups in the side chain exhibited absorption maximum (λ_max) at longer wavelength (565 nm) than PTOTBT (534 nm) and PTt‐BTBT (495 nm). PTOTBT showed higher thermal stability than the others. The prepared polymers were employed to polymer solar cells (PSCs) with a configuration of ITO/PEDOT‐PSS/polymer: PC₆₁BH/LiF/Al. Power conversion efficiency of the PSC‐based on PTEHTBT was 1.32%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of well‐defined cyclodextrin‐core star polymers

The synthesis of 21‐arm methyl methacrylate (MMA) and styrene star polymers is reported. The copper (I)‐mediated living radical polymerization of MMA was carried out with a cyclodextrin‐core‐based initiator with 21 independent discrete initiation sites: heptakis[2,3,6‐tri‐O‐(2‐bromo‐2‐methylpropionyl]‐β‐cyclodextrin. Living polymerization occurred, providing well‐defined 21‐arm star polymers with predicted molecular weights calculated from the initiator concentration and the consumed monomer as well as low polydispersities [e.g., poly(methyl methacrylate) (PMMA), number‐average molecular weight (M_n) = 55,700, polydispersity index (PDI) = 1.07; M_n = 118,000, PDI = 1.06; polystyrene, M_n = 37,100, PDI = 1.15]. Functional methacrylate monomers containing poly(ethylene glycol), a glucose residue, and a tert‐amine group in the side chain were also polymerized in a similar fashion, leading to hydrophilic star polymers, again with good control over the molecular weight and polydispersity (M_n = 15,000, PDI = 1.03; M_n = 36,500, PDI = 1.14; and M_n = 139,000, PDI = 1.09, respectively). When styrene was used as the monomer, it was difficult to obtain well‐defined polystyrene stars at high molecular weights. This was due to the increased occurrence of side reactions such as star–star coupling and thermal (spontaneous) polymerization; however, low‐polydispersity polymers were achieved at relatively low conversions. Furthermore, a star block copolymer consisting of PMMA and poly(butyl methacrylate) was successfully synthesized with a star PMMA as a macroinitiator (M_n = 104,000, PDI = 1.05). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2206–2214, 2001     

Multicenter nature of titanium‐based Ziegler–Natta catalysts: Comparison of ethylene and propylene polymerization reactions

This article discusses the similarities and differences between active centers in propylene and ethylene polymerization reactions over the same Ti‐based catalysts. These correlations were examined by comparing the polymerization kinetics of both monomers over two different Ti‐based catalyst systems, δ‐TiCl₃‐AlEt₃ and TiCl₄/DBP/MgCl₂‐AlEt₃/PhSi(OEt)₃, by comparing the molecular weight distributions of respective polymers, in consecutive ethylene/propylene and propylene/ethylene homopolymerization reactions, and by examining the IR spectra of “impact‐resistant” polypropylene (a mixture of isotactic polypropylene and an ethylene/propylene copolymer). The results of these experiments indicated that Ti‐based catalysts contain two families of active centers. The centers of the first family, which are relatively unstable kinetically, are capable of polymerizing and copolymerizing all olefins. This family includes from four to six populations of centers that differ in their stereospecificity, average molecular weights of polymer molecules they produce, and in the values of reactivity ratios in olefin copolymerization reactions. The centers of the second family (two populations of centers) efficiently polymerize only ethylene. They do not homopolymerize α‐olefins and, if used in ethylene/α‐olefin copolymerization reactions, incorporate α‐olefin molecules very poorly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1745–1758, 2003     

Copolymerization of propylene with 1,3‐butadiene using isospecific zirconocene catalysts

Poly(propylene‐ran‐1,3‐butadiene) was synthesized using isospecific zirconocene catalysts and converted to telechelic isotactic polypropylene by metathesis degradation with ethylene. The copolymers obtained with isospecific C₂‐symmetric zirconocene catalysts activated with modified methylaluminoxane (MMAO) had 1,4‐inserted butadiene units ( 1,4‐BD ) and 1,2‐inserted units ( 1,2‐BD ) in the isotactic polypropylene chain. The selectivity of butadiene towards 1,4‐BD incorporation was high up to 95% using rac‐dimethylsilylbis(1‐indenyl)zirconium dichloride (Cat‐A)/MMAO. The molar ratio of propylene to butadiene in the feed regulated the number‐average molecular weight (M_n) and the butadiene contents of the polymer produced. Metathesis degradations of the copolymer with ethylene were conducted with a WCI₆/SnMe₄/propyl acetate catalyst system. The ¹H NMR spectra before and after the degradation indicated that the polymers degraded by ethylene had vinyl groups at both chain ends in high selectivity. The analysis of the chain scission products clarified the chain end structures of the poly(propylene‐ran‐1,3‐butadiene). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5731–5740, 2007     

Synthesis and characterization of poly(phenylacetylenes) featuring activated ester side groups

Four monomers based on 4‐ethynylbenzoic acid have been synthesized, one of those featuring an activated ester. With the metathesis catalytic system WCl₆/Ph₄Sn, these acetylenic monomers could successfully be polymerized yielding conjugated polymers with molecular weights of around 10,000 to 15,000 g/mol and molecular weight distributions M_w/M_n ≤ 2.1. Also the copolymerization of phenylacetylene or methyl 4‐ethynylbenzoate with pentafluorophenyl 4‐ethynylbenzoate as reactive unit was conducted. Polymer analogous reactions of the reactive polymers and copolymers with amines have been investigated and it was found that poly(pentafluorophenyl 4‐ethynylbenzoate) featured a significant reactivity, such that reactions proceeded quantitatively even with aromatic amines. Moreover the UV‐Vis spectra of the activated ester based polymer before and after conversion with aliphatic amines showed a change, indicating an effect on the conjugated backbone of the polymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and reactions of cysteine‐based telechelic polymers

The radical polyaddition of N‐4‐vinylbenzoyl‐L ‐cysteine methyl ester (VCM) was carried out in the presence of 2,2′‐azobisisobutyronitrile (AIBN, 3 mol %) as an initiator in dimethyl formamide (DMF) with monomer concentrations of 0.5 and 1.0 M at 60 °C for 20 h under nitrogen atmosphere to afford the corresponding polymers [poly(VCM), PVCM] with number‐average molecular weights (M_n)'s of 5300 and 18,000 in 92 and 95% yields, respectively. The obtained polymers had a heterotelechelic structure with thiol and olefin end moieties. The radical polymerization of methyl methacrylate and trityl methacrylate was carried out in the presence of PVCM with AIBN (3 mol %) as an initiator in DMF at 60 °C for 20 h to afford the block copolymers with M_n values in the range of 13,000–26,800 in good yields. PVCM [M_n = 18,000; polydispersity (M_w/M_n) = 1.56] was treated with 4 equiv of NaOH aq. (1.0 M) to afford the polymer having carboxyl groups in the side chain with a M_n of 17,300 and M_w/M_n of 1.88 in 95% yield and was also oxidized to polysulfoxide and polysulfone with 4 equiv of H₂O₂ per sulfide unit in CH₂Cl₂ (1.0 M) for 20 h. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 23–31, 2001     

Chemical modification of poly(methylphenylsiloxane)

Poly(methylphenylsiloxane) (PMPS) with a narrow molecular weight distribution (MWD) was prepared by anionic polymerization, and ring‐functionalized using procedures optimized to minimize chain degradation. The products were characterized by NMR and IR spectroscopy, and the MWD of the polymers was analyzed by size exclusion chromatography, to monitor polymer degradation and crosslinking during the functionalization reactions. Electrophilic substitution was used to introduce nitro and bromo groups on the phenyl ring of the polymer. Nitration with fuming nitric acid yielded up to 8 mole % substitution with some chain degradation. Bromination was achieved with bromine in the presence of either pyridine or triethylamine. A substitution level of up to 14 mole % and a small increase in the polydispersity index (M_w/M_n) were obtained with triethylamine. Hydroxyethyl functionalities were obtained by lithiation of the brominated PMPS via metal‐halogen exchange, and reaction with ethylene oxide. A polymer with 3 mole % hydroxyethyl functionalities was obtained with moderate chain degradation. A substitution level of 6 mole % could be achieved under different conditions, but with more extensive chain degradation. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 653–664, 1999     

Synthesis of hydrocarbon polymers containing bulky dibenzobicyclic moiety by ROMP and their characteristic optical properties

The eight‐membered cyclic monomer, prepared by Diels–Alder reaction of 1,5‐cyclooctadiene and anthracene, polymerized via Ru‐catalyzed ring‐opening metathesis to efficiently afford high polymers (M_n up to 631,000). Unsaturated moieties in the main chain of the obtained polymer were hydrogenated with a homogeneous ruthenium catalyst in quantitative conversion, confirmed by ¹H‐NMR measurement. The self‐standing membranes were provided by casting the tetrahydrofuran solutions of both nonhydrogenated and hydrogenated polymers. The obtained membranes showed high transparency in the region of >300 nm with mechanical flexibility. Thermal gravimetric analysis revealed that both nonhydrogenated and hydrogenated polymers decomposed in two stages. The first‐stage decomposition starting at around 230 °C was caused by retro Diels–Alder reaction forming anthracene, proven by pyrolysis gas chromatography mass spectroscopy (GC‐MS) analyses. Mechanical grinding of the polymers induced the formation of anthracene in solid state, which transformed the polymer into blue‐luminescent materials under UV irradiation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1392–1400     

Arborescent polypeptides from γ‐benzyl l‐glutamic acid

The synthesis of arborescent polymers with poly(γ‐benzyl L‐glutamate) (PBG) side chains was achieved through successive grafting reactions. The linear PBG building blocks were produced by the ring‐opening polymerization of γ‐benzyl L‐glutamic acid N‐carboxyanhydride initiated with n‐hexylamine. The polymerization conditions were optimized to minimize the loss of amino chain termini in the reaction. Acidolysis of a fraction of the benzyl groups on a linear PBG substrate and coupling with linear PBG using a carbodiimide/hydroxybenzotriazole promoter system yielded a comb‐branched or generation zero (G0) arborescent PBG. Further partial deprotection and grafting cycles led to arborescent PBG of generations G1 to G3. The solvent used in the coupling reaction had a dramatic influence on the yield of graft polymers of generations G1 and above, dimethylsulfoxide being preferable to N,N‐dimethylformamide. This grafting onto scheme yielded well‐defined (M_w/M_n ≤ 1.06), high molecular weight arborescent PBG in a few reaction cycles, with number‐average molecular weights and branching functionalities reaching over 10⁶ and 290, respectively, for the G3 polymer. α‐Helix to coiled conformation transitions were observed from N,N‐dimethylformamide to dimethyl sulfoxide solutions, even for the highly branched polymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5270–5279