Improved interfacial properties of PI composites through graphene oxide and carbon nanotubes on carbon fiber surface

Carbon nanotubes (CNTs) have been identified as excellent nanoreinforcements for carbon fiber (CF)–reinforced polymers regarding a wide range of engineering applications. The outstanding properties of CNTs, such as their large surface area, high mechanical strength, and low manufacturing cost bring them to be distinguished nanoreinforcements for carbon fiber–reinforced polymers to form multifunctional and multiscale composites. Electrophoretic deposition of graphene oxide for CNTs onto the CF surface was conducted. The presence of graphene oxide–CNTs may effectively increase both the roughness and wettability of the CF surface, resulting in an improvement to the interfacial bonding strength between the CF and the polyimide (PI).     

Synthesis,curing and properties of poly(phthalazione ether sulfone ketone) copolymers crosslinked by click chemistry

Functionalized poly(phthalazinone ether sulfone ketone) was synthesized by successive chloromethylation and azidation, followed by curing reaction with the propargyl end-groups of various molecular weight crosslinking agents in the presence of Cu(Ⅰ) catalyst via the azide-alkyne click reaction. The influences of the chain length of crosslinking agents on the poly(phthalazinone ether sulfone ketone) system were studied. FTIR and DSC tests demonstrated certain crosslinking by azide-alkyne reaction with the formation of triazole ring. DSC results showed that curing temperature shifted to lower temperatures considerably in the presence of Cu(Ⅰ) catalyst. TGA showed cured polymers were of much higher thermal stability, including higher thermal decomposition temperatures and higher char-yielding properties. After being cured, the polymers became insoluble in organic solvents and the gel fraction of the cured polymers exceeded 71%. Wide-angle X-ray diffraction results indicated there was a short distance order in the poly(ether sulfone)(PES) main chain except for the azido methyl poly(phthalazinone ether sulfone ketone) and 4,4'-bis(2-propynyloxy) biphenyl( AMPPESK-BP) system.     

Preparation and investigation of tribological properties of ultra‐high molecular weight polyethylene (UHMWPE)/graphene oxide

This article has been devoted to investigation of the tribological properties of ultra‐high molecular polyethylene/graphene oxide nanocomposite. The nanocomposite of ultra‐high molecular polyethylene/graphene oxide was prepared with 0.5, 1.5, and 2.5 wt% of graphene oxide and with a molecular weight of 3.7 × 10⁶ by in‐situ polymerization using Ziegler–Natta catalyst. In this method, graphene oxide was used along with magnesium ethoxide as a novel bi‐support of the Ziegler–Natta catalyst. Analyzing the pin‐on‐disk test, the tribological properties of the nanocomposite, such as wear rate and mean friction coefficient, were investigated under the mentioned contents of graphene oxide. The results showed that an increase in graphene oxide content causes a reduction in both wear rate and mean coefficient friction. For instance, by adding only 5 wt% graphene oxide to the polymeric matrix, the wear rate and mean coefficient friction decreased about 34% and 3.8%, respectively. Also, the morphological properties of the nanocomposite were investigated by using X‐ray diffraction and scanning electron microscopy. In addition, thermal properties of the nanocomposite were analyzed using differential scanning calorimetry, under various contents of graphene oxide. The results of the morphological test indicated that the graphene oxide was completely exfoliated into the polymeric matrix without any agglomeration. Copyright © 2016 John Wiley & Sons, Ltd.     

Polyaniline decorated graphene oxide on sulfonated poly(ether ether ketone) membrane for direct methanol fuel cells application

In direct methanol fuel cells (DMFC), methanol crossover is a major issue which has reduced the performance of polymer electrolyte membrane (PEM) for energy generation. In this study, graphene oxide (GO) and conductive polyaniline decorated GO (PANI-GO) were used as additives in fabrication of sulfonated poly(ether ether ketone) (SPEEK) nanocomposite PEM membrane to reduce methanol crossover. PANI-GO was synthesized by in situ polymerization method and the formation of PANI coated GO nanostructures was confirmed by surface morphology and crystallinity analysis. The membrane morphology and topography analysis confirmed that GO and PANI-GO were well dispersed on the surface of SPEEK membrane. 0.1 wt% PANI-GO modified SPEEK nanocomposite membrane exhibited the highest water uptake and ion exchange capacity of 40% and 1.74 meq g^?1, respectively. The oxidative stability of the nanocomposite membranes also improved. Lower methanol permeability of 4.33 × 10^?7 cm^?2S^?1 was noticed for 0.1 wt% PANI-GO modified SPEEK membrane. PANI-GO modified SPEEK membrane enhanced the proton conductivity, which was due to the existence of acidic and hydrophilic group present in PANI and GO. PANI-GO modified SPEEK membrane held higher selectivity of 1.94 × 10⁴ S cm^?3 s^?1. Overall, these studies revealed that PANI-GO modified SPEEK membrane is a potential material for DMFC applications.     

Anchoring calcium carbonate on graphene oxide reinforced with anticorrosive properties of composite epoxy coatings

Calcium carbonate nanoparticles (nano‐CaCO₃) anchored graphene oxide (GO) sheet nanohybrids (GO‐CaCO₃) are fabricated, and their structure can be measured by scanning electron microscope, transmission electron microscopy, X‐ray photoelectron spectroscopy, X‐ray diffraction and Fourier‐transform infrared spectroscopy analysis. Afterwards, composite epoxy coatings, filled with GO and GO‐CaCO₃ nanohybrids, are prepared via a curing process. The dispersion and anticorrosive properties of composite epoxy coatings are investigated. The results reveal that GO‐CaCO₃ nanohybrids achieve a homogeneous dispersion as well as reinforce corrosion resistance of epoxy coatings. Furthermore, the anticorrosive mechanisms are tentatively proposed for the GO‐CaCO₃/epoxy coatings. Copyright © 2016 John Wiley & Sons, Ltd.     

Sulfonated carbon nanotubes/sulfonated poly(ether sulfone ether ketone ketone) composites for polymer electrolyte membranes

A series of composite membranes consisting of sulfonated carbon nanotubes (sCNTs) and sulfonated poly(ether sulfone ether ketone ketone) were successfully fabricated via the solution casting method. The chemical structure, as well as the long‐term stability of the sCNTs in different solvents, was investigated by Fourier transform infrared (FTIR) analysis and solubility experiment, respectively. The morphology, tensile strength, proton conductivity, and methanol permeability of the composite membranes were also investigated. The scanning electron microscope (SEM) observation indicated the good dispersion of the carbon nanotubes in polymer matrix as well as the strong interfacial bonding between the sulfonated poly(ether sulfone ether ketone ketone) (SPESEKK) matrix and sCNTs. The addition of either pristine carbon nanotubes or modified carbon nanotubes significantly enhanced the tensile strength of the SPESEKK membrane. The proton conductivity of the SPESEKK membrane increased while the methanol permeability decreased as the sCNTs content increased, showing a strong interaction between the modified nanotubes and SPESEKK. Copyright © 2010 John Wiley & Sons, Ltd.     

Poly(ether ether ketone)/poly(aryl ether sulfone) blends: Melt rheological behavior

Dynamic rheological measurements were carried out on blends of poly(ether ether ketone) (PEEK)/poly(aryl ether sulfone) (PES) in the melt state in the oscillatory shear mode. The data were analyzed for the fundamental rheological behavior to yield insight into the microstructure of PEEK/PES blends. A variation of complex viscosity with composition exhibited positive–negative deviations from the log‐additivity rule and was typical for a continuous‐discrete type of morphology with weak interaction among droplets. The point of transition showed that phase inversion takes place at composition with a 0.6 weight fraction of PEEK, which agreed with the actual morphology of these blends observed by scanning electron microscopy. Activation energy for flow, for blend compositions followed additive behavior, which indicated that PEEK/PES blends may have had some compatibility in the melt. Variation of the elastic modulus (G′) with composition showed a trend similar to that observed for complex viscosity. A three‐zone model used for understanding the dynamic moduli behavior of polymers demonstrated that PEEK follows plateau‐zone behavior, whereas PES exhibits only terminal‐zone behavior in the frequency range studied. The blends of these two polymers showed an intermediate behavior, and the crossover frequency shifted to the low‐frequency region as the PEEK content in PES increased. This revealed the shift of terminal‐zone behavior to low frequency with an increased PEEK percentage in the blend. Variation of relaxation time with composition suggested that slow relaxation of PEEK retards the relaxation process of PES as the PEEK concentration in the blend is increased because of the partial miscibility of the blend, which affects the constraint release process of pure components in the blend. A temperature‐independent correlation observed in the log–log plots of G′ versus loss modulus (G″) for different blend systems fulfilled the necessary condition for their rheological simplicity. Further, the composition‐dependent correlations of PEEK/PES blends observed in a log–log plot of G′ versus G″ showed that the blends are either partially miscible or immiscible and form a discrete‐continuous phase morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1548–1563, 2004     

Interface characteristic of aramid fiber reinforced poly(phthalazinone ether sulfone ketone) composite

Interface is an important microstructure for advanced polymer‐matrix composite. The composite interface is the bridge and the link for stress transferring between the fiber and the matrix resin. In this work, oxygen plasma treatment was used for modification of aramid fiber surface. The effects of plasma treatment power on interlaminar shear strength of composite were evaluated by short‐beam shear test. The morphologies of both the aramid fiber surface and its composite interface fracture were observed by SEM. The chemical structure and surface chemical composition of the plasma‐treated and separated fibers were analyzed by Fourier transform infrared (FTIR) and XPS, respectively. The results showed that the interlaminar shear strength of composite was enhanced by 33% with plasma treatment power of 200 W. The FTIR and XPS results indicated that the active functional groups were introduced onto the aramid fiber surface by plasma treatment forming chemical bonds with the poly(phthalazinone ether sulfone ketone) resin. The SEM results proved that the aramid fiber surface was roughened by plasma treatment enhancing the mechanical bond with the poly(phthalazinone ether sulfone ketone) resin. The composite rupture occurred from the composite interface to the fiber or the matrix resin. Copyright © 2017 John Wiley & Sons, Ltd.     

Synthesis of copolymers of poly(ether sulfone ether ketone ketone) and poly(ether ketone diphenyl ketone ether ketone ketone) by electrophilic Friedel–Crafts solution polycondensation

A new monomer, 4,4′‐bis(4‐phenoxybenzoyl)diphenyl(BPOBDP), was synthesized via a two‐step synthetic procedure. A series of novel poly(ether sulfone ether ketone ketone)/poly(ether ketone diphenyl ketone ether ketone ketone) copolymers were prepared by electrophilic Friedel–Crafts solution copolycondensation of isophthaloyl chloride (IPC) with a mixture of 4,4′‐diphenoxydiphenylsulfone (DPODPS) and 4,4′‐bis(4‐phenoxybenzoyl)diphenyl (BPOBDP), in the presence of anhydrous aluminum chloride and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The copolymers with 10–50 mol% DPODPS are semicrystalline and have remarkably increased T_gs over commercially available PEEK and PEKK. The copolymers with 40–50 mol% DPODPS had not only high T_gs of 170–172°C, but also moderate T_ms of 326–333°C, which are extremely suitable for melt processing. These copolymers have tensile strengths of 96.5–108.1 MPa, Young's moduli of 1.98–3.05 GPa, and elongations at break of 13–26% and exhibit excellent thermal stability and good resistance to acidity, alkali, and common organic solvents. Copyright © 2009 John Wiley & Sons, Ltd.     

Non-isothermal crystallization kinetics of continuous glass fiber-reinforced poly(ether ether ketone) composites

Current studies on crystallization kinetics for glass fiber-reinforced poly(ether ether ketone) mainly focused on short glass fiber-reinforced composites and their isothermal crystallization. It is worth noting that continuous glass fiber-reinforced poly(ether ether ketone) composite (CGF/PEEK) possesses relatively higher mechanical performance than short fiber-reinforced PEEK under high temperature. Here, for the first time, we investigate the non-isothermal crystallization kinetics and melting behavior of CGF/PEEK by differential scanning calorimetry at four different cooling rates. By evaluating the crystallite size of CGF/PEEK using X-ray diffraction, it is found that with the decreasing cooling rate, the crystallite size distribution evolves more uniform, and the size of crystallites enlarges. Besides, by systematical analysis, we find the modified Avrami equation can well describe crystallization behavior of the CGF/PEEK. The higher Avrami value of CGF/PEEK than pure PEEK indicates that CGF could introduce a more complex geometry effect on the crystallization. The addition of CGF greatly reduces the absolute value of crystallization activation energy of PEEK, suggesting that CGF can reduce the nucleation energy barrier. The obtained results illustrate that CGF can accelerate the nucleation rate due to heterogeneous nucleation while reduce the growth rate due to retarded polymer chain mobility. And the cooling conditions can influence crystal growth and morphology.

     

Preparation and characteristics of poly(benzoxazine-urethane)/graphene oxide composites: Toughness,mechanical and thermal properties

Poly(benzoxazine-urethane)/graphene oxide [poly(Bz-PU)/GO] composites were successfully prepared by blending benzoxazine (Bz) with graphene oxide (GO) and isocyanato (NCO)-terminated polyurethane prepolymer (PU), followed by thermally activated polymerization of the blends. The network was formed via the mutual reaction and intermolecular interaction among the hydroxyl of GO, NCO groups of PU and phenolic hydroxyl of Bz. The toughness shown from SEM images and tensile properties of polybenzoxazine (PBz) plastic composites can effectively be improved by alloying with PU and GO. The onset curing temperature and exothermic peak maximums of the polymerization obtained from differential scanning calorimetry decreased resulted from the GO addition. The thermogravimetric analysis showed that the incorporation of 0.5 wt% of GO slightly improved the thermal stability of poly(Bz-PU)/GO composites. Additionally, the storage modulus improved and the glass transition temperature (Tg) increased gradually as the increasing GO content not beyond a certain amount. Finally, the exothermic peaks of the polymerization were shifted to lower temperature, and the thermal stability increased for the ternary composites as the number average molecular weights (Mn) of polyol decreased.     

Synergistic effects of functionalized graphene and functionalized multi-walled carbon nanotubes on the electrical and mechanical properties of poly(ether sulfone) composites

Mixed fillers composed of functionalized graphene (f-G) and functionalized multi-walled carbon nanotubes (f-CNTs) (f-G-f-CNTs) were prepared and their synergistic effects in terms of enhancing the electrical conductivity and tensile modulus of poly(ether sulfone) (PES) composites were investigated. The results indicate that the electrical conductivity of the 5 wt% f-G-f-CNTs(W_f-G/W_f-CNTs = 1:1)/PES composite was 2.2 times higher than that of the 5 wt% f-G/PES composite and 8.9 times higher than that of the 5 wt% f-CNTs/PES composite. Moreover, the tensile modulus of the 5 wt% f-G-f-CNTs(W_f-G/W_f-CNTs = 1:1)/PES composite relative to that of the 5 wt% f-G/PES composite and 5 wt% f-CNTs/PES composite increased by 16.5% and 50.6%, respectively. Additionally, enhancements in the electrical conductivity and tensile modulus of the PES composite depended on the weight ratio of f-G and f-CNTs in the mixed fillers. The electrical conductivity and tensile modulus exhibited maximum values when the weight ratios of f-G and f-CNTs were 1:3 and 1:1, respectively. When the weight ratio of f-G and f-CNTs was fixed at 1:1, the f-G-f-CNTs(W_f-G/W_f-CNTs = 1:1)/PES composite showed a percolation threshold of 0.22 vol%, much lower than that of the f-G/PES composite.     

Electrospun poly(3‐hexylthiophene)/poly(ethylene oxide)/graphene oxide composite nanofibers: effects of graphene oxide reduction

In this article, we report on the production by electrospinning of P3HT/PEO, P3HT/PEO/GO, and P3HT/PEO/rGO nanofibers in which the filler is homogeneously dispersed and parallel oriented along the fibers axis. The effect of nanofillers' presence inside nanofibers and GO reduction was studied, in order to reveal the influence of the new hierarchical structure on the electrical conductivity and mechanical properties. An in‐depth characterization of the purity and regioregularity of the starting P3HT as well as the morphology and chemical structure of GO and rGO was carried out. The morphology of the electrospun nanofibers was examined by both scanning and transmission electron microscopy. The fibrous nanocomposites are also characterized by differential scanning calorimetry to investigate their chemical structure and polymer chains arrangements. Finally, the electrical conductivity of the electrospun fibers and the elastic modulus of the single fibers are evaluated using a four‐point probe method and atomic force microscopy nanoindentation, respectively. The electrospun materials crystallinity as well as the elastic modulus increase with the addition of the nanofillers while the electrical conductivity is positively influenced by the GO reduction. Copyright © 2016 John Wiley & Sons, Ltd.     

Probing the tribological behaviors in water of novel poly(phthalazione ether sulfone ketone) and its composites based on the state of aggregation and the microstructure

In this paper, novel poly(phthalazione ether sulfone ketone) (PPESK) and its composites reinforced with carbon fibers (CFs) were prepared, and their tribological behaviors in pure and sea water were comparatively investigated. Affected by the noncoplanar twisted aromatic structure in the molecular skeleton, the aggregation of the macromolecular chain in PPESK was amorphous, resulting in very high water absorption of PPESK matrix. The invading water molecules led to a sharp decrease in the hardness of PPESK surface, resulting in very high wear rate of PPESK in water. Although CF/PPESK composites had higher water absorption than pure PPESK, their wear processes in water were no longer dominated by high water absorption but by the load‐carrying effect of CFs, ascribed to the good CF/PPESK interfacial adhesion. Therefore, CF/PPESK composites exhibited very low wear rates in the order of 10^?7 mm³/Nm in water, which decreased with the CF content increasing until the content of CFs reached 50%. The results revealed that the most critical factor determining the wear behavior of a fiber‐reinforced polymer composite sliding in water is the fiber/matrix interface but not the water absorption of the polymer matrix. Copyright © 2017 John Wiley & Sons, Ltd.     

Influence of surface properties of graphene oxide/carbon fiber hybrid fiber by oxidative treatments combined with electrophoretic deposition

An effective way to prepare graphene oxide/carbon fiber hybrid fiber was proposed by the treatment with hydrogen peroxide and concentrated nitric acid combined with electrophoretic deposition process. Surface functional group, surface roughness, and surface morphologies of carbon fibers were examined by Fourier transform infrared spectrometer, atomic force microscopy, and scanning electron microscopy. Results showed that a uniform and thick graphene oxide films were constructed on the surface of carbon fiber. Deposition density increased by introduction of pretreatment of the carbon fiber in the electrophoretic deposition process has been shown as a possible method. Dynamic contact angle analysis results indicated that the deposition of graphene oxide significantly improved surface free energy of carbon fiber by increasing surface area and polar groups. The introduction of graphene oxide in the carbon fiber‐reinforced epoxy composites results in a 55.6% enhancement in the interfacial shear strength and confirms the remarkable improvement in the interfacial adhesion strength of the composites, and the fracture mechanism was also analyzed. Copyright © 2016 John Wiley & Sons, Ltd.     

Effects of methylene chloride sorption on the properties of poly(ether ether ketone)

Sorption of methylene chloride by poly(ether ether ketone) (PEEK) has been studied for both amorphous and highly crystalline polymer. After the determination of sorption and desorption curves, the crystallinity of the two materials after desorption was determined both by density and X-ray measurements. The experimental results indicate the existence of solvent-induced crystallization in initially amorphous PEEK and a virtual lack of this process in highly crystalline PEEK. In the latter case, the observed density increase is attributed to solvent compression and a decrease in free volume. The mechanical behavior of both PEEKs is consistent with their crystallinity levels. The mechanical behavior of both PEEKs before and after sorption allows us to discern the separate effects of the two processes to which the presence of methylene chloride in PEEK gives rise, i.e., plasticization and solvent-induced crystallization. © 1994 John Wiley & Sons, Inc.     

A DSC study of miscibility and phase separation in crystalline polymer blends of phenolphthalein poly(ether ether sulfone) and poly(ethylene oxide)

The miscibility of blends of phenolphthalein poly(ether ether sulfone) (PES-C) and poly(ethylene oxide) (PEO) was established on the basis of the thermal analysis results. Differential scanning calorimetry (DSC) studies showed that the PES-C/PEO blends prepared by casting from N,N-dimethylformamide (DMF) possessed a single, composition-dependent glass transition temperature (T_g), and thus that PES-C and PEO are miscible in the amorphous state at all compositions at lower temperature. At higher temperature, the blends underwent phase separation, and the PES-C/PEO blend system was found to display a lower critical solution temperature (LCST) behavior. The phase separation process in the blends has also been investigated by using DSC. Annealed at high temperatures, the PES-C/PEO blends exhibited significant changes of thermal properties, such as the enthalpy of crystallization and fusion, temperatures of crystallization and melting, depending on blend composition when phase separation occurred. These changes reflect different characteristics of phase structure in the blends, and were taken as probes to determine phase boundary. From both the thermal analysis and optical microscopy, the phase diagram of the blend system was established. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1383–1392, 1997     

End-group cross-linked membranes based on highly sulfonated poly(arylene ether sulfone) with vinyl functionalized graphene oxide as a cross-linker and a filler for proton exchange membrane fuel cell application

High-performance end-group cross-linked sulfonated poly(arylene ether sulfone) (SPAES) membranes are developed using thiolate-terminated SPAES with very high degree of sulfonation (DS) such as 90 mol% (SK-SPAES90) and vinyl functionalized graphene oxide (VGO) as a cross-linker and a filler through the thiol-Michael addition reaction. Since free-standing membranes for fuel cell application could not be prepared using the water soluble and highly proton conductive SPAES with high DS of 90 mol%, cross-linked SPAES90 membranes are intentionally prepared. The cross-linked membranes are found to have good physicochemical properties with excellent proton conductivity that can be applied for the proton exchange membrane. In particular, the cross-linked SPAES90 membrane prepared using 1.0 wt% of VGO exhibits better dimensional stability than a SPAES70 membrane from the linear SPAES with DS of 70 mol% and the proton conductivities of this membrane are larger than those of Nafion 211 at 80 °C under different relative humidity conditions (40%-95%).     

Blue phase liquid crystals affected by graphene oxide modified with aminoazobenzol group

Liquid-crystalline blue phases (BPs) are stable only for very narrow temperature range between the isotropic and the chiral nematic phase that severely hinders their applicability. Herein, the aminoazobenzol group was chemically grafted onto epoxy group of graphene oxide (GO) via addition reaction. Successful grafting of aminoazobenzol group was confirmed using X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), UV–vis absorption spectra and thermogravimetric analysis (TGA). The resultant aminoazobenzol group–modified GO sheets, which is reduced (RGO-Az), were easily redispersable in common organic solvents or liquid crystals (LCs). By doping different contents of RGO-Az, nanosheets could stabilise BP and increase the BP range. When doped with 0.5 wt% RGO-Az, the mixtures show the wider range with 5.9°C than the range with 3.6°C of BPLCs without RGO-Az. Meanwhile, the phase sequence and the range of the aforementioned phases are reproducible upon heating and cooling, which shows that the BPs doped with RGO-Az nanosheets are thermodynamically stable.