A comparative study on wear and friction characteristics of phenolic composite coatings filled with different morphologies ZnO

In this paper, different morphologies ZnO (disk‐like, rod‐like, and nanoparticles) were introduced into phenolic composite coatings to comparatively investigate the tribological properties. The structural and morphological characterization was conducted with Raman spectroscopy, X‐ray diffraction, and scanning electron microscopy. The tribological performances of composite coatings were evaluated using ring‐on‐block tester under dry condition at room temperature. Experimental results indicated that composite coatings filled with 1 wt% ZnO micro‐disks possessed the optimal tribological performances. It was attributed to the strong interfacial interaction between ZnO micro‐disks and phenolic matrix induced by their specific polar structure. Moreover, different loads and sliding speeds were employed to further evaluate the tribological performances of ZnO micro‐disks/phenolic composite coatings. The outcome revealed that ZnO micro‐disks were potential anti‐wear fillers under harsh condition.     

Local Structure of ZnO Micro Flowers and Nanoparticles Obtained by Micro‐Segmented Flow Synthesis

The micro‐segmented flow technique was applied for continuous synthesis of ZnO micro‐ and nanoparticles with short residence times of 9.4 s and 21.4 s, respectively. The obtained particles were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Small angle X‐ray scattering (SAXS) and photoluminescence spectroscopy were used to determine the size and optical properties of ZnO nanoparticles. In addition, extended X‐ray absorption fine structure (EXAFS) spectroscopy was employed to investigate local structural properties. The EXAFS measurements reveal a larger degree of structural disorder in the nanoparticles than the microparticles. These structural changes should be taken into consideration while evaluating the size‐dependent visible emission of ZnO nanoparticles.     

Preparation and application of polystyrene‐grafted ZnO nanoparticles

The precursor of ZnO was prepared by precipitation and ZnO nanoparticles were obtained by calcination afterwards. Poly(styrene) (PSt) was grafted onto the ZnO nanoparticles in a non‐aqueous suspension to reduce the aggregation among nanoparticles and to improve the compatibility between nanoparticles and the organic matter. The obtained samples were characterized by X‐ray powder diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT‐IR), zeta potential measurement, lipophilic degree (LD) test, photocatalytic experiments, sedimentation test, and contact angle measurement. The LD of composite particles after a high‐temperature treatment was stable. The photoluminescence of PSt‐grafted ZnO nanoparticles was observed by naked eyes and was recorded using a digital camera. The ZnO nanoparticles were used to reinforce poly(vinylidene fluoride) (PVDF) films and the mechanical and electric properties of the films were also measured. Copyright © 2007 John Wiley & Sons, Ltd.     

Preparation of nanostructured Co–Mo alloy electrodes and investigation of their electrocatalytic activity for hydrazine oxidation in alkaline medium

Cobalt and cobalt–molybdenum alloy electrodes are prepared by galvanic deposition on copper substrates. In this paper, we report a study on the influence of alloying cobalt with molybdenum for the oxidation of hydrazine in 1 M NaOH aqueous solutions. The electrocatalytic properties of the electrodes are studied by cyclic voltammetry (CV), chronoamperometry (CA), and electrochemical impedance spectroscopy (EIS). Scanning electron microscopy (SEM), X‐ray diffraction (XRD), energy‐dispersive X‐ray spectroscopy (EDS,) and inductively coupled plasma (ICP) analysis demonstrate that the structural features and compositions of the as‐prepared Co–Mo coatings vary with the deposition conditions. Electrochemical characterization indicates that the electrochemical properties and the electrocatalytic activity of the investigated alloys were strongly dependent on the microstructural features obtained under different deposition conditions. The overall experimental data indicate that alloying cobalt with molybdenum metal leads to an increase of the electrocatalytic activity in hydrazine electroxidation compared to when using the pure cobalt electrode. High catalytic efficiencies were achieved on Co/25 at.% Mo and Co/33 at.% Mo electrodes, the latter being the best electrocatalyst for hydrazine electroxidation.     

Organic–inorganic nanocomposites of (2‐hydroxypropyl)cellulose as a precursor of nanocrystalline zinc oxide layers

The sol–gel method of synthesis of the hybrid nanocomposite films of ZnO/(2‐hydroxypropyl) cellulose (HPC) on silica glass is presented. The sol phases were prepared for different weight ratios of zinc acetate dihydrate to HPC in the presence of triethylamine (TEA). Raman spectrum of the mixture of ZnAc and HPC indicates coordinating interaction between zinc ion and HPC. The generation of ZnO nanoparticles in the HPC matrix proceeds in situ through the annealing of the gel phase at a temperature of 160°C. Identification of ZnO nanoparticles in the HPC matrix is done by using photoluminescence (PL), UV–Vis, and Raman spectroscopy. The films of ZnO/HPC nanocomposite are transparent in the visible light and show a higher energy value of absorption edge compared with ZnO in the bulk. Nanocrystalline films of ZnO were obtained by the calcination of ZnO/HPC nanocomposite at 500°C. ZnO films possess a good transparency for the visible light and high absorbance for UV light. Nanocrystallite sizes of ZnO particles were estimated from the X‐ ray lines broadening. The properties of ZnO layers were studied by the evaluation of PL, X‐ray investigation and atom force microscope (AFM) scanning, and the optical absorption edge. Copyright © 2008 John Wiley & Sons, Ltd.     

Influence of varying hard segments on the properties of chemically crosslinked moisture‐cured polyurethane‐urea

Polyurethane prepolymers are widely used in the reactive hot melt adhesives and moisture‐cured coatings. The chemically crosslinked moisture‐cured formulation based on PEG‐1000 and isophorone diisocyanate was prepared with NCO/OH ratio of 1.6:1.0. Trimethylol propane was used as a crosslinking agent. The excess isocyanate of the prepolymer was chain extended in the ratio of 2:1 (NCO/OH) with different aliphatic diols, and 4:1 with different aromatic diamines. The polymer network maturation during moisture cure was followed by dynamic mechanical thermal analyzer (DMTA) instrument. The thermal and dynamic mechanical properties of the crosslinked polymers were evaluated using thermogravimetric analysis, differential scanning calorimetric analysis and DMTA. Surface properties were evaluated through angle‐resolved X‐ray photoelectron spectroscopy. The present article discusses the physical properties of moisture‐cured polyurethane‐urea (MCPU) containing chemical crosslinks in the hard segment. The complete moisture‐cured polymers showed amorous results toward room temperature modulus, tensile strength, hardness, thermal stability, and transparency. The surface properties showed the enrichment of soft segments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 102–118, 2006     

Synthesis of ZnO photocatalyst modified with activated carbon for a perfect degradation of ciprofloxacin and its secondary pollutants

The proposed research, presents the synthesis, characterization, and photocatalytic accomplishment of ZnO nanoplate (ZnOs) modified with activated carbon derived from Konar bark. The obtained nanocomposite (photocatalyst) was characterized by scanning electron microscopy (SEM), X‐ray diffraction (XRD), Raman spectroscopy, X‐ray photoelectron spectroscopy (XPS), and Brunauer–Emmett–Teller (BET). First, the ZnO photocatalyst and activated carbon (AC) were prepared separately; then, the ZnO photocatalyst was modified with activated carbon. Various parameters namely pH, degradation time, and photocatalyst dose were optimized and studied in multivariate method by design expert7 software. The synergic efficiency of ZnO‐AC (adsorbent/photocatalyst) exhibited a good rate of ciprofloxacin (CIP) removal under visible irradiation. In addition, first pseudo order kinetic and isotherms equations were calculated. Moreover, the identification of degradation products was performed by ultra performance liquid chromatography‐tandem mass spectrometer (UPLC‐MS/MS). It is for the first time that a ZnO photocatalyst modified with activated carbon (ZnO‐AC) applied for CIP degradation.     

Well‐defined polycaprolactone precursors for low surface‐energy polyurethane films

For the purpose of developing model coating systems, it is important to use well‐defined coating precursors. In this work, polyester oligomers were synthesized by controlled ring‐opening polymerization of ε‐caprolactone and 4‐tert‐butyl‐ε‐caprolactone via an activated monomer mechanism. These well‐defined oligomers, including 3‐armed hydroxyl‐functionalized polyesters and perfluoroalkyl‐end‐capped linear polyesters, have been obtained with controlled functionality and low‐molecular weight polydispersity and without the formation of cyclic structures, as demonstrated by MALDI‐ToF MS analyses. The polymer architecture and functionality can be tuned by using different initiating alcohols. These oligomers have been used as precursors to prepare model low surface‐energy polyurethane coatings. Upon the addition of about 1 wt % of fluorine in the polyurethane films, the advancing contact angles for water and hexadecane have been increased to 105° and 78°, respectively; the surface enrichment of fluorinated species has been confirmed by X‐ray photoelectron spectroscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 218–227, 2008     

Negative Charging of Au Nanoparticles during Methanol Synthesis from CO2/H2 on a Au/ZnO Catalyst: Insights from Operando IR and Near‐Ambient‐Pressure XPS and XAS Measurements

The electronic and structural properties of Au/ZnO under industrial and idealized methanol synthesis conditions have been investigated. This was achieved by kinetic measurements in combination with time‐resolved operando infrared (DRIFTS) as well as in situ near‐ambient pressure X‐ray photoelectron spectroscopy (NAP‐XPS) and X‐ray absorption near‐edge spectroscopy (XANES) measurements at the O K‐edge together with high‐resolution electron microscopy. The adsorption of CO during the reaction revealed the presence of negatively charged Au nanoparticles/Au sites during the initial phase of the reaction. Near‐ambient‐pressure XPS and XANES demonstrate the build‐up of O vacancies during the reaction, which goes along with a substantial increase in the rate of methanol formation. The results are discussed in comparison with previous findings for Cu/ZnO and Au/ZnO catalysts.     

Deposition and characterization of TiAlSiN coatings prepared by hybrid PVD coating system

TiAlSiN coatings with different Si contents were deposited on silicon and high‐temperature alloy by using a hybrid physical vapor deposition coating system, where the cathodic arc ion plating was combined with a twin target mid‐frequency magnetron sputtering. The chemical composition, microstructure, cross‐sectional structure and morphology were carried out by X‐ray photoelectron spectroscope (XPS), X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and transmission electron microscope (TEM), respectively. NanoTest 600 nanomechanical system and ball‐on‐disc friction tester were used to investigate the mechanical and friction properties of TiAlSiN coatings. The worn surface of the TiAlSiN coatings and counterballs were investigated by means of surface profilometer and optical microscope. The wear rates were also measured by surface profilometer. The results showed that the Si addition did not change the coatings growth orientation, and the coating transfered into amorphous phase when the Si content reached about 13.9 at.%. The tribological properties and the hardness were improved by solid solution of Si atoms and grain boundary strengthening of SiN_x amorphous phase with moderate Si content addition. In addition, the SiNx amorphous phase improved oxidation resistance of TiAlN coating, but with a high Si content (more than 8.3 at.% in this work) the agglomeration of SiN_x amorphous phase would reduce the mechanical properties and oxidation resistance of the coating. Copyright © 2014 John Wiley & Sons, Ltd.     

ZnO thin films prepared on titanium substrate by PLD technique at different substrate temperatures

ZnO thin films were grown by pulsed laser deposition on titanium substrates at different substrate temperatures ranging from 300 to 700 °C. X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS),photoluminescence, and Raman spectroscopy are employed to investigate the change of properties. XRD, XPS, and Raman data showed that the films consisted of TiO₂ at high substrate temperature, which will deteriorate the crystallization quality of ZnO films. The optimum temperature for the growth of ZnO films on the Ti substrate is about 500 °C in this paper. The ZnO films grown on titanium substrate can be used in direct current, microwave, and medical applications. Copyright © 2014 John Wiley & Sons, Ltd.     

Well Oriented ZnO Nanorods Array: Negative Resistance and Optical Switching

Well‐oriented ZnO nanorods (NRs) arrays were grown on Si, alumina, quartz, and FTO substrates through a ZnO seed layer followed by low temperature wet chemical process. The influence of sputtered ZnO seed layer thickness (100, 50, 32, and 16 nm), annealing temperature and CuO_x coverage on the characteristics of ZnO NRs were investigated in this study. The crystalline structural, chemical, morphological, optical, and electrical properties of ZnO NRs arrays were studied by X‐ray diffraction (XRD), field emission‐ scanning electron microscopy equipped by energy dispersive X‐ray spectroscopy (FE‐SEM/EDX), Raman scattering, UV/Vis ‐ near IR absorption spectroscopy and current‐voltage characteristic. XRD and Raman spectra measurement revealed that the synthesize ZnO displayed hexagonal wurtzite structure. The individual rod diameter, density, and orientation can be controlled by varying the seed layer thickness. The mean diameter and maximum length of ZnO NRs are around 55–66 nm and 282 nm, respectively. ZnO NRs/ ZnO thin film structure shows optical switching and negative differential resistance behavior as applicable to ON/OFF gate and memory devices.     

Modification of poly(benzimidazole‐amide) nanocomposites by the incorporation of amine‐functionalized ZnO nanoparticles: Thermal and morphological characterization

Fabrication, characterization, and properties of novel poly(benzimidazole‐amide)/functionalized ZnO nanocomposites (PBIA/APS‐ZnO NCs) were investigated. At first, an aromatic PBA containing 3 imidazole units per repeat unit was synthesized by direct polycondensation of 1,3‐bis(5‐carboxylic acid‐2‐benzimidazole)benzene (BCAB) with 5‐(2‐benzimidazole)‐1,3‐phenylenediamine (DAMI) with good yield as a polymeric matrix. The periphery of zinc oxide nanoparticles (ZnO NPs) was modified with 3‐aminopropyltriethoxysilane (APS) to have a better dispersion NPs and enhancing interactions between nanoparticles and PBIA matrix. Different percentages of functionalized NPs (0, 4, 8, and 12 wt.%) were then embedded in PBA matrix through ultrasonic irradiation technique. Fourier transform infrared and thermo‐gravimetric analysis (TGA) confirmed that APS was successfully attached on the ZnO NP surface. The obtained NCs were characterized by means of Fourier transform infrared, X‐ray diffraction, scanning electron microscopy, and TGA. The TGA of the PBIA/APS‐ZnO NCs showed the enhancement in the thermal stability in comparison with the neat PBIA and that this increase is higher when the NP content increases. Scanning electron microscopy analyses of NCs revealed that the dispersion of APS‐ZnO NPs was uniformly done in the PBIA matrix.     

Fabrication of zinc oxide nanowires/polymer composites by two‐photon polymerization

We present an approach to fabricate ZnO nanowires/polymer composite into three‐dimensional microstructures, based on two‐photon polymerization direct laser writing, a fabrication method that allows submicrometric spatial resolution. The structural integrity of the structures was inferred by scanning electron microscopy, while the presence and distribution of ZnO nanowires was investigated by energy dispersive X‐ray, Raman spectroscopy, and X‐ray diffraction. The optical properties of the produced composite microstructures were verified by imaging the characteristic ZnO emission using a fluorescence microscope. Hence, such approach can be used to develop composite microstructures containing ZnO nanowires aiming at technological applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 333–337     

50 keV H+ ion beam irradiation of Al doped ZnO thin films: Studies of radiation stability for device applications

Thin films of Al doped ZnO (Al:ZnO) were deposited on two substrates (Si and glass) at room temperature and 300°C using DC magnetron sputtering. These films were bombarded with 50 keV H⁺ beam at several fluences. The pristine and ion beam irradiated films were analysed by X‐ray diffraction, Raman spectroscopy, scanning electron microscopy, and UV‐Vis spectroscopy. The X‐ray diffraction analysis, Hall measurements, Raman and UV‐Vis spectroscopy confirm that the structural and transport properties of Al:ZnO films do not change substantially with beam irradiation at chosen fluences. However, in comparison to film deposited at room temperature, the Al:ZnO thin film deposited at 300°C shows increased transmittance (from 70% to approximately 90%) with ion beam irradiation at highest fluence. The studies of surface morphology by scanning electron microscopy reveal that the ion irradiation yields smoothening of the films, which also increases with ion fluences. The films deposited at elevated temperature are smoother than those deposited at room temperature. In the paper, we discuss the interaction of 50 keV H⁺ ions with Al:ZnO films in terms of radiation stability in devices.     

Ultrasonic treatment as recent and environmentally friendly route for the synthesis and characterization of polymer nanocomposite having PVA and biosafe BSA‐modified ZnO nanoparticles

The present study deals with the immobilization of ZnO nanoparticles (NPs) as nanofiller inside poly(vinyl alcohol) (PVA) by solution casting method which is a low‐cost, environmental‐friendly, and rapid method of sonochemistry. Firstly, the surface of ZnO NPs was treated by bovine serum albumin (BSA) in the phosphate‐buffered solution under ultrasonic cavitation. Three diverse polymeric nanocomposites (NCs) are formed by changing the percentage of ZnO@BSA NPs (3, 6, and 9 wt%) with same amount of PVA. The structure properties, morphology, and thermal stability of prepared NCs were determined through Fourier transform‐infrared spectroscopy, X‐ray diffraction, energy‐dispersive X‐ray spectroscopy (EDX) and optical UV‐Visible spectrum, transmission electron microscopy (TEM), and field emission scanning electron microscopy. The presence and the dispersal of the ZnO@BSA NPs in the PVA matrix were recognized by TEM. In the X‐ray diffraction analysis, the values of mean particle size using Debye‐Scherrer equation were estimated in the range 4 to 6 nm that is almost in agreement with TEM analysis. Increase of 14% in thermal stability and also increase of more than 2‐fold of the tensile strength of PVA/ZnO@BSA NC 9 wt% in respect to the pure PVA showed that the modified NPs well dispersed within PVA and attached to it.     

Towards Organized Hybrid Nanomaterials at the Air/Water Interface Based on Liquid‐Crystal/ZnO Nanocrystals

The ability to self‐assemble nanosized ligand‐stabilized metal oxide or semiconductor materials offers an intriguing route to engineer nanomaterials with new tailored properties from the disparate components. We describe a novel one‐pot two‐step organometallic approach to prepare ZnO nanocrystals (NCs) coated with deprotonated 4‐(dodecyloxy)benzoic acid (i.e., an X‐type liquid‐crystalline ligand) as a model LC system (termed ZnO‐LC1 NCs ). Langmuir and Langmuir–Blodgett films of the resulting hybrids are investigated. The observed behavior of the ZnO NCs at the air/water interface is rationalized by invoking a ZnO‐interdigitation process mediated by the anchored liquid‐crystalline shell. The ordered superstructures form according to mechanism based on a Z nO‐ i nterdigitation p rocess mediated by l iquid c rystals (termed ZIP‐LC). The external and directed force applied upon compression at the air/water interface and the packing of the ligands that stabilize the ZnO cores drives the formation of nanorods of ordered internal structure. To study the process in detail, we follow a nontraditional protocol of thin‐film investigation. We collect the films from the air/water interface in powder form ( ZnO‐LC1 LB ), resuspend the powder in organic solvents and utilize otherwise unavailable experimental techniques. The structural and physical properties of the resulting superlattices were studied by using electron microscopy, atomic force microscopy, X‐ray studies, dynamic light scattering, thermogravimetric analysis, UV/Vis absorption, and photoluminescence spectroscopy.     

Antimicrobial,mechanical, optical and thermal properties of PVC/ZnO‐EDTA nanocomposite films

Covalent surface functionalization of synthesized ZnO nanoparticles (NP)s with ethylenediaminetetraacetic acid (EDTA) was successfully carried out. Modified ZnO‐EDTA NPs as a viable and inexpensive filler were incorporated into poly(vinyl chloride) PVC matrix after their chemical modification to investigate the agglomeration behavior. All prepared materials including modified NPs and PVC/ZnO‐EDTA nanocomposites (NC)s were analyzed by Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, thermogravimetric analysis, X‐ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. Fabricated PVC/ZnO‐EDTA NCs were reported to have high transparency and improved mechanical properties compared with PVC. Modified ZnO and the fabricated NCs were shown to exhibit excellent antibacterial activity against two bacteria species: Escherichia coli and Staphylococcus aureus. The obtained NCs could be considered as self‐extinguishing materials on the basis of the LOI values. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis and Characterization of PANI/ZnO Nanocomposites

This paper presents our results on the successful fabrication of HCl‐doped polyaniline (PANI)/ZnO nanocomposites via an electrochemical synthesis route. Different weight percents of ZnO nanoparticles were uniformly dispersed in the PANI matrix. The interaction between the dispersed ZnO nanoparticle and PANI was studied using X‐ray diffraction, ultraviolet–visible absorption spectroscopy, photoluminescence (PL) spectroscopy, X‐ray photoelectron spectroscopy, atomic force microscopy, thermogravimetry, and transmission electron microscopy. It is shown that the doping state of the PANI/ZnO nanocomposite is highly improved as compared to that of PANI. The dispersed PANI/ZnO nanocomposites exhibit enhanced PL behavior and thermal stability.     

Anchoring calcium carbonate on graphene oxide reinforced with anticorrosive properties of composite epoxy coatings

Calcium carbonate nanoparticles (nano‐CaCO₃) anchored graphene oxide (GO) sheet nanohybrids (GO‐CaCO₃) are fabricated, and their structure can be measured by scanning electron microscope, transmission electron microscopy, X‐ray photoelectron spectroscopy, X‐ray diffraction and Fourier‐transform infrared spectroscopy analysis. Afterwards, composite epoxy coatings, filled with GO and GO‐CaCO₃ nanohybrids, are prepared via a curing process. The dispersion and anticorrosive properties of composite epoxy coatings are investigated. The results reveal that GO‐CaCO₃ nanohybrids achieve a homogeneous dispersion as well as reinforce corrosion resistance of epoxy coatings. Furthermore, the anticorrosive mechanisms are tentatively proposed for the GO‐CaCO₃/epoxy coatings. Copyright © 2016 John Wiley & Sons, Ltd.