New polymer electrolyte membrane for medium-temperature fuel cell applications based on cross-linked polyimide Matrimid and hydrophobic protic ionic liquid

New hydrophobic protic ionic liquid, 2-butylaminoimidazolinium bis(trifluoromethylsulfonyl)imide (BAIM-TFSI), has been synthesized. The ionic liquid showed good thermal stability to at least 350 °C. The conductivity of BAIM-TFSI determined by electrochemical impedance method was found to be 5.6 × 10^?2 S/cm at 140 °C. Homogeneous composite films based on commercial polyimide (PI) Matrimid and BAIM-TFSI containing 30–60 wt% of ionic liquid were prepared by casting from methylene chloride solutions. Thermogravimetric analysis data indicated an excellent thermal stability of PI/BAIM-TFSI composites and thermal degradation points in the temperature range 377 °C–397 °C. The addition of ionic liquid up to 50 wt% in PI films does not lead to any significant deterioration of the tensile strength of the polymer. The dynamic mechanical analysis results indicated both an increase of storage modulus E′ of PI/BAIM-TFSI composites at room temperature and a significant E′ decrease with temperature compared with the neat polymer. The cross-linking of the PI with polyetheramine Jeffamine D-400 allowed to prepare PI/Jeffamine/BAIM-TFSI (50%) membrane with E′ value of 300 MPa at 130 °C. The ionic conductivity of this cross-linked composite membrane reached the level of 10^?2 S/cm at 130 °C, suggesting, therefore, its potential use in medium-temperature fuel cells operating in water-free conditions.     

A study of the behavior of charge carriers in an organic non‐volatile memory device with a thin metal layer between polymers

The behaviors of charge carriers were investigated to understand the reversible bistability in the polymer device with an embedded thin metal layer between the metal electrodes. The reversible bistability was sensitive to the condition of the embedded thin metal layer that was prepared by depositing 5 nm Al by 0.8 Å/sec. The device was controlled by the charge and the discharge in the effective trap sites of the embedded Al layer. Poly(N‐vinylcarbazole) as an organic active material merely conducted the charge transport function. The effective trap sites were contributed by the change of the reversible conductance and also preferred to be in a high conduction state. They took relatively low energy states easily as the device was affected by thermal stimulation at 150°C. The modification of the embedded Al layer improved its performances. Copyright © 2009 John Wiley & Sons, Ltd.     

Control of thermal cross‐linking reactions and the degree of crystallinity of syndiotactic 1,2‐polybutadiene

Thermal stability, crystallization, morphological development, subsequently melting, and crystallinity control of a syndiotactic 1,2‐polybutadiene sample were carefully carried out by thermogravimetry (TGA), polarized optical microscopy (POM), differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), and wide‐angle X‐ray diffraction (WAXD), respectively. The experiments indicate that thermal cross‐linking reaction rates under nitrogen protection and in air are different for this polymer at temperature above 155 °C. Under nitrogen protection, the thermal cross‐linking reaction rate is delayed and the mechanism of melt crystallization obtained from the DSC results is in good accordance with that from POM observation. TMDSC results indicate that melting–recrystallization–melting model is more proper to explain the double melting events of this sample. At the same time, the evolution of the degree of crystallinity as the function of the time was investigated by WAXD profiles for the samples firstly crystallized at 145 °C for 1 h and then kept at 163 °C mediated between the temperatures of the double peaks. It shows that as prolonging the annealing time at 163 °C thermal cross‐linking reactions possibly occur, leading to gradual reduction of the apparent crystallite sizes, evaluated by Scherrer equation and the degree of crystallinity. The changing sequence of the relative intensity of the stronger four diffraction peaks with time due to thermal cross‐linking reactions is (111)/(201) > (210) > (010) > (200)/(110). © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2885–2897, 2005     

Thermal and spectral stability of electroluminescent hyperbranched copolymers containing tetraphenylthiophene‐quinoline‐triphenylamine moieties

Fluorescent hyperbranched copolymers (HB‐x, x = 1–4) with inherent tetraphenylthiophene, triphenylamine (TPA) and quinoline (Qu) moieties were prepared to study the influence of the TPA branching point on the thermal and the spectral stability. All the HB‐x copolymers exhibited high glass transition temperatures (T_gs = 245–315 °C) with the detected values increasing with the increasing branching TPA content in the HB‐x. The solid HB‐x films possess high emission efficiency with the resulting quantum yields (?_Fs) in the ranges of 0.72–0.74. More importantly, the HB‐x copolymers and the derived light‐emitting devices exhibit high photoluminescence (PL) and electroluminescence (EL) stability towards thermal annealing at temperatures higher than 200 °C. After annealing at 200 °C (or 300 °C), no change was observed in the respective PL and EL spectra of HB‐1 (or HB‐4) copolymers. The spectral stability was found to correlate with T_g and with the highest branching density, HB‐4 copolymer possesses the highest thermal stability among all HB‐xs and show no EL spectral change after annealing at 300 °C for 4 h. The results indicate that all the branched HB‐x copolymers are promising candidates for the polymer light‐emitting diodes due to their high quantum yield and spectral stability. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and properties of high‐performance functional polyimides containing rigid nonplanar conjugated tetraphenylethylene moieties

A simple diamine (TetraPEDA) containing rigid nonplanar conjugated tetraphenylethylene (TetraPE) moieties was designed and synthesized through Wittig–Horner and Suzuki coupling reactions. Four kinds of high‐performance functional polyimides (PI) were thus prepared by the polymerization of TetraPEDA and four dianhydrides, respectively. Because of the introduction of the aromatic rigid nonplanar TetraPE structure, the PI exhibited special fluorescent characteristics, as the maximum fluorescence emission of the four PI was observed at 425–505 nm in NMP solution and at 470–491 nm in film state. Also these organo‐soluble PI showed outstanding properties, such as low dielectric constant (even without fluorinated substituent), light color, high glass transition temperatures (382–443 °C) and thermal stability in air (T_d5% up to 565 °C), and excellent mechanical properties. The polymer memory devices with the configuration of indium tin oxide/PI/aluminum (ITO/PI/Al) exhibited distinct volatile memory characteristics of static random access memory, with an ON/OFF current ratio of 1 × 10⁴ to 1 × 10⁵. These functional PI showed attractive potential applications in the field of high performance flexible polymer photoconducting devices or fluorescent polymer memory devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Fire resistance properties of heavyweight magnetite concrete in comparison with normal basalt- and quartz-based concrete

Nowadays application of radiation shielding structures grows over the world. Nuclear buildings represent one of the most complicated radiation shielding structures; that is why a particular type of concrete is required to withstand different conditions during their lifespan. Unique properties such as the behaviour under elevated temperatures, radiation shielding, and thermal stability properties are essential to guarantee the fire resistance safety of nuclear buildings. However, some gaps are still there, warranting further investigation, particularly the thermal stability and fire-resistance properties of the heavyweight concrete. The properties are mechanical, physical, and deformation properties of concrete after being subjected to elevated temperature. This paper investigated the fire resistance properties of three concrete mixes. There were magnetite-based concrete, basalt-based concrete, and quartz-based concrete. Compressive and flexural strength, spalling, mass loss, porosity, and scanning electron microscopy were measured for the three concrete types after being subjected to different temperature steps at 20, 150, 300, 500, and 800 °C. The three types of concrete showed different fire resistance properties. Magnetite-based concrete has better heat/fire resistance than basalt- and quartz-based concrete; there was no significant change up to 500 °C, and explosive spalling occurred at 800 °C. Correspondingly, the maximum change in porosity and reduction in the compressive and flexural strength occurred at 300 °C, which indicates the good thermal stability of magnetite-based concrete. Concerning basalt-based and quartz-based concretes, cracks were observed at 500 °C, and cracks with colour change and small spalling were initiated at 800 °C. Therefore, the maximum growth in the porosity and the high reduction in the compressive and flexural strength in basalt-based concrete occurred at 800 °C. Likewise, the extreme change in the porosity occurred at 500 °C, and the drastic reduction in the compressive and the flexural strength in the quartz-based concrete was relatively high at 500 °C and 800 °C. The SEM observations and analysis obtained the appearance of microcracks, voids and degradation of C-S-H in different concrete mixes at 500 and 800℃.

     

Performance of high-temperature thermosetting polyimide composites modified with thermoplastic polyimide

The preparation of polyimide (PI) resin with high heat resistance and toughness is a significant challenge. In this study, thermoplastic PI (TPI) was used to toughen thermosetting PIs, and toughened PI (TPI/PI) blends were prepared. The modified PI resin system exhibited good thermal stability, excellent heat resistance, and high toughness. The results indicated that the TPI/PI blends maintained the curing behavior and characteristics of the PI oligomer. The T_g of the cured TPI/PI blend exceeded 395 °C, and the T_5% values were in the range of 533–563 °C, suggesting excellent thermal stability and heat resistance. The maximum impact strength was increased by 46% compared with that of pure PI, indicating the excellent toughening effect of the TPI. Carbon fiber-reinforced PI composites were prepared using the toughening system as a matrix. The compression-after-impact values of the carbon fiber-reinforced PI composites were up to 190 MPa, indicating the excellent toughness of the materials.     

Effect of Annealing on the Electrical Properties of CuxS Thin Films

Copper sulphide CuS was deposited on three substrates; glass, Indium Tin Oxide (ITO) and Ti by using spray pyrolysis deposition (SPD). After depositing CuS thin films on the substrates at 200 °C, they were annealed at 50, 100, 150, and 200 °C for 1 hour. Structural measurements revealed covellite CuS and chalcocite Cu₂S phases for thin films before and after annealing at 200 °C with changes in intensities, and only covellite CuS phase for thin films after annealing at 50, 100, and 150 °C. Morphological characteristics show hexagonal-cubic crystals for the CuS thin film deposited on glass substrate and plates structures for films deposited on ITO and Ti substrates before annealing, these crystals became bigger in size and there were be oxidation and some agglomerations in some regions with formation of plates for CuS on glass substrate after annealing at 200 °C. For Hall Effect measurements, thin films sheet resistivity and mobility increased after annealing while the carrier concentration decreased. Generally, the thin film deposited on ITO substrate had the lowest resistivity and the highest carrier concentration before and after annealing. The thin film deposited on Ti substrate had the highest mobility before and after annealing, which makes it the best thin film for device performance. The objective of this research is to show the improvement of thin films electrical properties especially the mobility after annealing those thin films.     

Anisotropy in optical transmittance and molecular chain orientation of silver- dispersed uniaxially drawn polyimide films

The anisotropy in optical transmittance in the visible and near-infrared region observed for uniaxially drawn and silver-dispersed polyimide (PI) films was investigated. The films were prepared in a one-step operation that consists of thermal curing and simultaneous uniaxial drawing of poly(amic acid) (PAA) films dissolving 5.7 ∼ 20 mol% of silver nitrate. The PAA was converted to PI by heating, and the PI chains were orientated along the drawing direction during curing. Silver nanoparticles were precipitated in the films when they were cured in air and under nitrogen. In particular, silver nanoparticles aggregated along drawing direction and spheroidal nanoparticles (size of longer axis: 10–25 nm, aspect ratio: ca. 1.5) were observed in the films cured in air, and distinct anisotropy in optical transmittance was observed. The maximum optical anisotropy was obtained with a specific holding time at the final curing temperature (320 °C). In addition, the anisotropy can be controlled by polymer chain orientation when films are cured with the optimal holding time. In optimized preparing conditions, anisotropies in transmittance larger than 500 : 1 were obtained at the wavelengths between 700 and 900 nm, and its optical properties were retained after annealing at 150 °C for 1 hr. The PI films thus obtained can be used as thermally stable thin-film polarizers. Copyright © 2003 John Wiley & Sons, Ltd.     

Latent reactive polymers containing isocyanate moiety that show extreme stability under aerobic atmosphere

This article deals with the latent reactive polymers having isocyanate moiety obtained from the radical copolymerization of 2‐propenyl isocyanate ( 2PI ) with styrene, 2PI with methyl methacrylate ( MMA ), and 2‐methacryloyloxyethyl isocyanate ( MOI ) with styrene. The radical copolymerization was carried out in benzene (5.00 M by total monomer) in the presence of AIBN (3.00 mol % of total monomer) at 60 °C for 24 h. The isocyanate moiety in each copolymer was stable at room temperature for more than 6 months under aerobic atmosphere, because no change of the infrared absorption based on isocyanate group of the resulting copolymer at around 2250 cm^?1 was observed. Isocyanate moiety of obtained copolymer (poly( 2PI ‐co‐ St )) reacted with excess diamines or diols at 80 °C in THF solution to afford the crosslinked polymer quantitatively. These results could demonstrate that isocyanate moiety in the copolymers showed thermal and reactive latency. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2448–2453, 2006     

Synthesis and optoelectronic properties of alternating benzofuran/terfluorene copolymer with stable blue emission

The solution processable alternating benzofuran/terfluorene copolymer bearing side oxadiazole groups ( PBF‐OXD ) was synthesized and its optoelectronic properties and color stability were investigated. Electron‐deficient and stereohindered oxadiazole units were used as pendent groups to compensate for the poor electron‐transporting ability of a p‐type polymer backbone, to depress the intermolecular π‐stacking, and to improve solubility while retaining polymer blue emission. PBF‐OXD showed a glass transition at 135 °C and an onset decomposition temperature of ～345 °C. A simple EL device, with the configuration of ITO/PEDOT:PSS/ PBF‐OXD /Ba/Al, displayed a stable blue emission (λ_max = 434 nm), good color purity (full width half‐maximum = 59 nm), maximum brightness of 1400 cd/m², and a maximum luminance efficiency of 0.95 cd/A. The PL and EL spectra changed slightly on annealing and on increasing the applied voltage. These results show that the as‐synthesized copolymer PBF‐OXD had integrated respective functions of its different building blocks and exhibited good thermal and color stability with improved EL performance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5488–5497, 2009     

Effects of the architecture and environment on polymeric molecular assemblies of novel amphiphilic diblock copolynorbornenes with narrow polydispersity via living ring‐opening metathesis polymerization

Diblock copolymers of 5‐(methylphthalimide)bicyclo[2.2.1]hept‐2‐ene (NBMPI) and 1,5‐cyclooctadiene were synthesized by living ring‐opening metathesis polymerization with a well‐defined catalyst {RuCl₂(CHPh)[P(C₆H₁₁)₃]₂}. Unhydrogenated diblock copolymers showed two glass transitions due to poly(NBMPI) and polybutadiene segments, such as two glass‐transition temperatures at ?86.5 and 115.3 °C for poly 1a and ?87.2 and 115.3 °C for poly 1b . However, only one melting temperature could be observed for hydrogenated copolymers, such as 119.8 °C for poly 2a and 121.7 °C for poly 2b . The unhydrogenated diblock copolymer with the longer poly(NBMPI) chain (poly 1a ; temperature at 10% mass loss = 400 °C) exhibited better thermal stability than the one with the shorter poly(NBMPI) chain (poly 1b ; temperature at 10% mass loss = 385 °C). Two kinds of hydrogenated diblock copolymers, poly 2a and poly 2b , exhibited relatively poor solubility but better thermal stability than unhydrogenated diblock copolymers because of the polyethylene segments. Poly[(hydrochloride quaternized 2‐norbornene‐5‐methyleneamine)‐b‐butadiene]‐1 (poly 3a ) was obtained after the hydrolysis and quaternization of poly 1a . Dynamic light scattering measurements indicated that the hydrodynamic diameters of the cationic copolymer (poly 3a ) in water (hydrodynamic diameter = 1580 nm without salt), methanol/water (4/96 v/v; hydrodynamic diameter = 1500 nm without salt), and tetrahydrofuran/water (4/96 v/v; hydrodynamic diameter = 1200 nm without salt) decreased with increasing salt (NaCl) concentration. The effect of temperature on the hydrodynamic diameter of hydrophobically modified poly 3a was also studied. The inflection point of the hydrodynamic diameter of poly 3a was observed at various polymer concentrations around 30 °C. The critical micelle concentration of hydrophobically modified poly 3a was observed at 0.018 g dL^?1. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2901–2911, 2006     

Partially bio‐based aromatic polyimides derived from 2,5‐furandicarboxylic acid with high thermal and mechanical properties

Two novel bio‐based diamines are synthesized through introduction of renewable 2,5‐furandicarboxylic acid (2,5‐FDCA), and the corresponding aromatic polyimides (PIs) are then prepared by these diamines with commercially available aromatic dianhydrides via two‐step polycondensation. The partially bio‐based PIs possess high glass transition temperatures (T_gs) in the range from 266 to 364 °C, high thermal stability of 5% weight loss temperatures (T_5%s) over 420 °C in nitrogen and outstanding mechanical properties with tensile strengths of 79–138 MPa, tensile moduli of 2.5–5.4 GPa, and elongations at break of 3.0–12.3%. Some colorless PI films (PI‐1‐b and PI‐1‐c) with the transmittances at 450 nm over 85% are prepared. The overall properties of 2,5‐FDCA‐based PIs are comparable with petroleum‐based PI derived from isophthalic acid, displaying the potential for development of innovative bio‐based materials. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1058–1066     

The effect of photocrosslinkable groups on thermal stability of bulk heterojunction solar cells based on donor–acceptor‐conjugated polymers

Three different types of photocrosslinkable groups into a low band‐gap donor–acceptor‐conjugated polymer, namely poly{benzo[1,2‐b:4,5‐b′]dithiophene‐alt‐ thieno[3,4‐b]thiophene} (PBT), were developed to comparatively investigate the effect of the photocrosslinkable groups on the thermal stability of bulk heterojunction solar cells. Compared with vinyl groups, bromine‐ and azide‐ photocrosslinkable groups are more prompt for photocrosslinking to yield a denser crosslinking network, probably due to the different crosslinking mechanisms and reaction rates. In contrast to the reference device decreasing to less than 10% of its initial efficiency value after 80 h of annealing at 150 °C, a great improvement in the thermal stability of performance of all these crosslinked functional copolymers devices demonstrates that photocrosslinking can effectively improve the thermal stability of the active layer by suppressing [6,6]‐phenyl‐C₆₁‐butyric acid methyl diffusion and phase separation. Furthermore, the solar cells with crosslinked bromine‐ and azide‐functionalized PBT polymers showed very thermally stable photovoltaic device performance by retaining 78 and 66% of their initial device efficiency, respectively, whereas vinyl‐functionalized PBT devices retained only 51% of its initial value after long‐time thermal annealing. This suggests that an appropriate crosslinking network with homogenous active morphology could dramatically enhance the device stability without sacrificing the performance. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4156–4166     

Curing mechanism,heat resistance,and anticorrosion properties of a furan/methyl phenyl silicone coating

A coating composed by methyl phenyl silicone resin (PSi) and furan resin (FR) was prepared, and its curing mechanism, heat resistance, and anticorrosion properties were investigated by Fourier transform infrared spectroscopy, thermogravimetric analysis, electrochemical test, and chemical resistance test. Aldol condensation reaction between FR and PSi occurred at below 200°C, and PSi underwent self‐multidehydrogenation at above 200°C. These curing reactions gave excellent thermal stability and anticorrosion properties. Compared with pure PSi, the blended containing lower than 20 wt% FR had better thermal properties, manifested as over 390°C of 5 wt% weight loss temperature and over 40% of char yield at 800°C. The adhesion property of cured blended system on the metal surface reached the first level which exceeded that of pure PSi coating (the third level). Furthermore, the corrosion resistances of coating in acid, alkali, and salt environments were all improved compared with those of monomeric polymer coating. The impedance of blended coating in 3.5% NaCl solution decreased with increasing FR content, which was 1.8 × 10⁶ Ω cm² when the FR content was 40%, being higher than that of pure PSi coating (7.12 × 10⁵ Ω cm²). This was mainly due to the formation of a cross‐linked network structure based on Si―O―C bond and the enhanced adhesion of cured blended coating. In addition, the surface roughness of cured blended coating was below 2.0 μm, which may have a positive effect on drag reduction in real applications.     

Preparation and characterization of pavement materials with phase-change temperature modulation

A kind of pavement crack repairing material with temperature regulation property was successfully prepared through one-step method, in which the paraffin was incorporated into the polyurethane/epoxy resin-interpenetrating polymer networks. Differential scanning calorimeter results indicated that the phase-change latent heat of sample A was 14.4 kJ kg^?1, and the phase transition temperature was ??0.3 °C. FTIR and thermogravimetry measurements verified that the paraffin was successfully incorporated into the interpenetrating polymer network without leakage and reacted with the carrier, which exhibited high thermal stability above 300 °C. After 1 year of road test, there was no breakage for the repairing pavement with paraffin–polyurethane/epoxy resin-interpenetrating polymer networks, and there was almost no change for the accumulated attenuation of phase-change latent heat. Therefore, the materials of paraffin–polyurethane/epoxy resin-interpenetrating polymer networks have good chemical stability and thermal stability.

     

Polycycloalkylene-siloxane polymers: Synthesis and thermal study

Based on dicyclopentadiene and silacyclopentene, two linear polycycloalkylene-siloxane polymer systems have been synthesized and the thermal stability of the raw polymers evaluated by differential scanning calorimetry and thermal gravimetric analysis. The DSC data in nitrogen indicate that both polymer systems have excellent thermal stability. In air, these polymers begin to oxidize at approximately 150°C, with catastrophic oxidation occurring at about 400°C.     

New carbazole‐based conjugated polymers containing pyridylvinyl thiophene units for polymer solar cell applications: Morphological stabilization through hydrogen bonding

We have synthesized two conjugated polymers ( P1 , P2 ) containing alternating electron‐donating and ‐accepting units, based on N‐alkyl‐2,7‐carbazole, 4,7‐di(thiophen‐5‐yl)‐2,1,3‐benzothiadiazole and 3‐[2‐(4‐pyridyl)vinyl]thiophene units. These conjugated polymers contained different contents of pyridine units, which were incorporated to form hydrogen bonds with [6,6]‐phenyl‐C₆₁‐butyric acid (PCBA). When these hydrogen bonding interactions were present in the polymer thin films, their thermal stability improved; deterioration, which occurred through aggregation of PCBA methyl ester after lengthy annealing times, was also suppressed. The power conversion efficiency of a device incorporating the film featuring hydrogen bonding interactions remained at 75% of the original value after thermal annealing for 5 h at 140 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

In-situ synthesis of 3D printable mono- and Bi-metallic (Cu/Ag) nanoparticles embedded polymeric structures with enhanced electromechanical properties

The interest of additive manufacturing with 3D printing increases day by day, which provides improved mechanical, electrical, magnetic and thermal properties of 3D parts. The production of 3D parts with the stereolithography (SLA) method, which allows it to be produced with high precision, resolution and complex geometries, distinguishes itself from other alternative additive manufacturing methods (FDM. SLS. LOM. LMD etc.). However, studies on the preparation of functional 3D polymer nanocomposites with the SLA method are quite limited. This study aims to produce silver (Ag) and/or copper (Cu) based 3D polymer nanocomposites for enhancing its mechanical strength, thermal stability and electrical conductivity. Mono and bimetallic (Cu/Ag) nanoparticles have been in-situ synthesized by selective irradiation of laser beam method using a commercial SLA device. In this method, metal (Cu/Ag) acrylate containing photocurable resin is not only cured but also leads to thermal decomposition of metal ions into nanoparticles to form functional 3D structures. The mechanical, electrical and thermal properties of polymer nanocomposites are characterized in detail. As a result of the analysis, the nanoparticles, with an average diameter of 25–55 nm, are well dispersed in the polymer matrix without agglomeration. The temperature at which 5% weight loss of Ag and Cu based polymer structures is measured as 179.3 °C while the glass transition temperature is found to be 223.81 °C. Most importantly, the resistance values are significantly decreased from 456.62 GΩ (Gigaohm) to 1.50 GΩ by increasing the amount of Ag addition at 3D polymeric structures. Therefore, this study allows the production of polymer nanocomposites not only in complex structures but also in desired properties especially for electrically conductive materials, capacitors and electronic applications.     

The effect of post-irradiation annealing on the crosslinking of high-density polyethylene induced by gamma-radiation

Samples of two high-density polyethylenes having different crystallinity levels were gamma irradiated under vacuum at doses ranging from 20 to 300 kGy. Subsequently, the vials containing the irradiated samples were exposed to different post-irradiation treatments. Parts of the specimens were annealed while still under vacuum. The annealing time was 4 h and the annealing temperatures 110 °C or 150 °C. Others were exposed directly to air opening the vials without any thermal treatment. It was verified that in all cases the dosage to produce an incipient gel increases with the crystallinity of the initial sample. The amount of gel produced after exposing specimens of the same polymer to a given dose increases with the annealing temperature. The largest increment in the amount of gel produced at the completion of the post-irradiation treatment was found on the samples with the highest initial crystallinity level.Evidence of oxidation was found in all irradiated samples. The extent of oxidation depends on the initial crystallinity of the sample, the irradiation dose and the type of post-irradiation treatment. The heat of fusion measured in the annealed samples decreases with the gel content while the fusion temperature was slightly affected. Ductile or brittle behaviors were observed after testing specimens under tensile stress. The yield stress increases proportionally to the crystallinity level that, in turn, depends on the total dosage applied to the samples. The extensibility of ductile samples is determined by the amount of gel produced regardless of the degree of initial crystallinity and the type of annealing process applied to each sample.