A universal self‐eroding sacrificial bioink that enables bioprinting at room temperature

Natural polymer‐based hydrogel bioinks are widely used in bioprinting due to their suitability for recapitulation of in vivo cellular activities. However, preservation of the target geometry in a cell‐laden hydrogel is difficult to achieve. The aim of this study was to develop a universal sacrificial bioink that allows high cell viability and a better shape fidelity in the cell‐laden construct. A polysaccharide‐based universal sacrificial bioink was developed for microextrusion‐based bioprinting and was optimized to erode in 48 hours in the cell culture medium without formation of any undesired by‐products. The sacrificial hydrogel was prepared from alginate and agarose via a microwave oven assisted method and bioprinted at room temperature to generate microchannels in the cell‐laden hydrogel or to support a tubular structure and its biocompatibility determined by live/dead assay. Bioprinting time was significantly reduced, down to a few minutes for a large‐scale tissue model (1 minute 52 seconds for a 2 cm tubular structure), by means of a high bioprinting speed up to 25 mm/s. After 48 hours in the cell culture, the sacrificial bioink completely detached from the cell‐laden construct without causing any changes in its printed shape. Cell viability in the cell‐laden construct was observed to be more than 95% at the end of 3‐day culture. This novel sacrificial bioink enables bioprinting at room temperature without affecting oxygen and nutrient penetration into the cell‐laden hydrogel and allows retention of high cell viability and shape fidelity.     

Designing Gelatin Methacryloyl (GelMA)‐Based Bioinks for Visible Light Stereolithographic 3D Biofabrication

Bioinks play a key role in determining the capability of the biofabricatoin processes and the resolution of the printed constructs. Excellent biocompatibility, tunable physical properties, and ease of chemical or biological modifications of gelatin methacryloyl (GelMA) have made it an attractive choice as bioinks for biomanufacturing of various tissues or organs. However, the current preparation methods for GelMA‐based bioinks lack the ability to tailor their physical properties for desired bioprinting methods. Inherently, GelMA prepolymer solution exhibits a fast sol–gel transition at room temperature, which is a hurdle for its use in stereolithography (SLA) bioprinting. Here, synthesis parameters are optimized such as solvents, pH, and reaction time to develop GelMA bioinks which have a slow sol–gel transition at room temperature and visible light crosslinkable functions. A total of eight GelMA combinations are identified as suitable for digital light processing (DLP)‐based SLA (DLP‐SLA) bioprinting through systematic characterizations of their physical and rheological properties. Out of various types of GelMA, those synthesized in reverse osmosis (RO) purified water (referred to as RO‐GelMA) are regarded as most suitable to achieve high DLP‐SLA printing resolution. RO‐GelMA‐based bioinks are also found to be biocompatible showing high survival rates of encapsulated cells in the photocrosslinked gels. Additionally, the astrocytes and fibroblasts are observed to grow and integrate well within the bioprinted constructs. The bioink's superior physical and photocrosslinking properties offer pathways of tuning the scaffold microenvironment and highlight the applicability of developed GelMA bioinks in various tissue engineering and regenerative medicine applications.     

Three-Dimensional Bioprinting of Decellularized Extracellular Matrix-Based Bioinks for Tissue Engineering

Three-dimensional (3D) bioprinting is one of the most promising additive manufacturing technologies for fabricating various biomimetic architectures of tissues and organs. In this context, the bioink, a critical element for biofabrication, is a mixture of biomaterials and living cells used in 3D printing to create cell-laden structures. Recently, decellularized extracellular matrix (dECM)-based bioinks derived from natural tissues have garnered enormous attention from researchers due to their unique and complex biochemical properties. This review initially presents the details of the natural ECM and its role in cell growth and metabolism. Further, we briefly emphasize the commonly used decellularization treatment procedures and subsequent evaluations for the quality control of the dECM. In addition, we summarize some of the common bioink preparation strategies, the 3D bioprinting approaches, and the applicability of 3D-printed dECM bioinks to tissue engineering. Finally, we present some of the challenges in this field and the prospects for future development.     

Enhanced Maturation of 3D Bioprinted Skeletal Muscle Tissue Constructs Encapsulating Soluble Factor-Releasing Microparticles

Several microfabrication technologies have been used to engineer native-like skeletal muscle tissues. However, the successful development of muscle remains a significant challenge in the tissue engineering field. Muscle tissue engineering aims to combine muscle precursor cells aligned within a highly organized 3D structure and biological factors crucial to support cell differentiation and maturation into functional myotubes and myofibers. In this study, the use of 3D bioprinting is proposed for the fabrication of muscle tissues using gelatin methacryloyl (GelMA) incorporating sustained insulin-like growth factor-1 (IGF-1)-releasing microparticles and myoblast cells. This study hypothesizes that functional and mature myotubes will be obtained more efficiently using a bioink that can release IGF-1 sustainably for in vitro muscle engineering. Synthesized microfluidic-assisted polymeric microparticles demonstrate successful adsorption of IGF-1 and sustained release of IGF-1 at physiological pH for at least 21 days. Incorporating the IGF-1-releasing microparticles in the GelMA bioink assisted in promoting the alignment of myoblasts and differentiation into myotubes. Furthermore, the myotubes show spontaneous contraction in the muscle constructs bioprinted with IGF-1-releasing bioink. The proposed bioprinting strategy aims to improve the development of new therapies applied to the regeneration and maturation of muscle tissues.     

Digital Light Processing 3D Bioprinting of Gelatin-Norbornene Hydrogel for Enhanced Vascularization

Digital light processing (DLP) bioprinting can be used to fabricate volumetric scaffolds with intricate internal structures, such as perfusable vascular channels. The successful implementation of DLP bioprinting in tissue fabrication requires using suitable photo-reactive bioinks. Norbornene-based bioinks have emerged as an attractive alternative to (meth)acrylated macromers in 3D bioprinting owing to their mild and rapid reaction kinetics, high cytocompatibility for in situ cell encapsulation, and adaptability for post-printing modification or conjugation of bioactive motifs. In this contribution, the development of gelatin-norbornene (GelNB) is reported as a photo-cross-linkable bioink for DLP 3D bioprinting. Low concentrations of GelNB (2–5 wt.%) and poly(ethylene glycol)-tetra-thiol (PEG4SH) are DLP-printed with a wide range of stiffness (G' ≈120 to 4000 Pa) and with perfusable channels. DLP-printed GelNB hydrogels are highly cytocompatible, as demonstrated by the high viability of the encapsulated human umbilical vein endothelial cells (HUVECs). The encapsulated HUVECs formed an interconnected microvascular network with lumen structures. Notably, the GelNB bioink permitted both in situ tethering and secondary conjugation of QK peptide, a vascular endothelial growth factor (VEGF)-mimetic peptide. Incorporation of QK peptide significantly improved endothelialization and vasculogenesis of the DLP-printed GelNB hydrogels, reinforcing the applicability of this bioink system in diverse biofabrication applications.     

Effects of Processing Parameters of 3D Bioprinting on the Cellular Activity of Bioinks

In this review, few established cell printing techniques along with their parameters that affect the cell viability during bioprinting are considered. 3D bioprinting is developed on the principle of additive manufacturing using biomaterial inks and bioinks. Different bioprinting methods impose few challenges on cell printing such as shear stress, mechanical impact, heat, laser radiation, etc., which eventually lead to cell death. These factors also cause alteration of cells phenotype, recoverable or irrecoverable damages to the cells. Such challenges are not addressed in detail in the literature and scientific reports. Hence, this review presents a detailed discussion of several cellular bioprinting methods and their process‐related impacts on cell viability, followed by probable mitigation techniques. Most of the printable bioinks encompass cells within hydrogel as scaffold material to avoid the direct exposure of the harsh printing environment on cells. However, the advantages of printing with scaffold‐free cellular aggregates over cell‐laden hydrogels have emerged very recently. Henceforth, optimal and favorable crosslinking mechanisms providing structural rigidity to the cell‐laden printed constructs with ideal cell differentiation and proliferation, are discussed for improved understanding of cell printing methods for the future of organ printing and transplantation.     

Biofabrication of Cell‐Loaded 3D Spider Silk Constructs

Biofabrication is an emerging and rapidly expanding field of research in which additive manufacturing techniques in combination with cell printing are exploited to generate hierarchical tissue‐like structures. Materials that combine printability with cytocompatibility, so called bioinks, are currently the biggest bottleneck. Since recombinant spider silk proteins are non‐immunogenic, cytocompatible, and exhibit physical crosslinking, their potential as a new bioink system was evaluated. Cell‐loaded spider silk constructs can be printed by robotic dispensing without the need for crosslinking additives or thickeners for mechanical stabilization. Cells are able to adhere and proliferate with good viability over at least one week in such spider silk scaffolds. Introduction of a cell‐binding motif to the spider silk protein further enables fine‐tuned control over cell–material interactions. Spider silk hydrogels are thus a highly attractive novel bioink for biofabrication.     

Sonochemical Degradation of Gelatin Methacryloyl to Control Viscoelasticity for Inkjet Bioprinting

Inkjet printing enables the mimicry of the microenvironment of natural complex tissues by patterning cells and hydrogels at a high resolution. However, the polymer content of an inkjet-printable bioink is limited as it leads to strong viscoelasticity in the inkjet nozzle. Here it is demonstrated that sonochemical treatment controls the viscoelasticity of a gelatin methacryloyl (GelMA) based bioink by shortening the length of polymer chains without causing chemical destruction of the methacryloyl groups. The rheological properties of treated GelMA inks are evaluated by a piezo-axial vibrator over a wide range of frequencies between 10 and 10 000 Hz. This approach enables to effectively increase the maximum printable polymer concentration from 3% to 10%. Then it is studied how the sonochemical treatment effectively controls the microstructure and mechanical properties of GelMA hydrogel constructs after crosslinking while maintaining its fluid properties within the printable range. The control of mechanical properties of GelMA hydrogels can lead fibroblasts more spreading on the hydrogels. A 3D cell-laden multilayered hydrogel constructs containing layers with different physical properties is fabrictated by using high-resolution inkjet printing. The sonochemical treatment delivers a new path to inkjet bioprinting to build microarchitectures with various physical properties by expanding the range of applicable bioinks.     

Bioprinting Using Mechanically Robust Core–Shell Cell‐Laden Hydrogel Strands

The strand material in extrusion‐based bioprinting determines the microenvironments of the embedded cells and the initial mechanical properties of the constructs. One unmet challenge is the combination of optimal biological and mechanical properties in bioprinted constructs. Here, a novel bioprinting method that utilizes core–shell cell‐laden strands with a mechanically robust shell and an extracellular matrix‐like core has been developed. Cells encapsulated in the strands demonstrate high cell viability and tissue‐like functions during cultivation. This process of bioprinting using core–shell strands with optimal biochemical and biomechanical properties represents a new strategy for fabricating functional human tissues and organs.

     

Simulation of the bioadhesive gelatin‐alginate conjugate loaded with antibiotic drugs

In the present research, molecular modeling methods were used to study a novel bioadhesive composed of gelatin (protein) and alginate (polysaccharides), crosslinked with N‐(3‐dimethylaminopropyl)‐N′‐ethylcarbodiimide hydrochloride (EDC) and N‐hydroxysuccinimide (NHS). Three antibiotic drugs were added to the bioadhesive: Vancomycin, Ofloxacin, and Clindamycin. Computational tools were applied to estimate the crosslinking degree and compare the effect of the antibiotics on the physical properties of the gelatin‐alginate conjugate. The crosslinking degree was estimated by calculating the enthalpy of mixing of gelatin with alginate and their interaction with the crosslinking agents. The calculations revealed that gelatin mixes well with alginate, which enables their crosslinking. Various ratios between EDC and NHS were examined, and an optimal ratio was found. The interaction of alginate‐gelatin conjugate with the antibiotics was correlated to the experimental results of bonding strength. The most significant interaction of the conjugate is with clindamycin. The gelatin part is responsible for the strong interaction with clindamycin, and alginate forms strong interaction with ofloxacin. Thus, the interaction of alginate‐gelatin conjugate with the antibiotics is governed by the proportion between gelatin and alginate in the conjugate. The degradation rate of gelatin‐alginate was related to its interaction with water. It was found that the conjugate is highly hydrophilic. Gelatin is more soluble in water than both alginate and alginate‐gelatin and is probably the part in the conjugate that governs the solubility and degradation rate. Therefore, the degradation rate of the conjugate can be controlled by changing the proportion between gelatin and alginate.     

Rapid Formation of a Supramolecular Polypeptide–DNA Hydrogel for In Situ Three‐Dimensional Multilayer Bioprinting

A rapidly formed supramolecular polypeptide–DNA hydrogel was prepared and used for in situ multilayer three‐dimensional bioprinting for the first time. By alternative deposition of two complementary bio‐inks, designed structures can be printed. Based on their healing properties and high mechanical strengths, the printed structures are geometrically uniform without boundaries and can keep their shapes up to the millimeter scale without collapse. 3D cell printing was demonstrated to fabricate live‐cell‐containing structures with normal cellular functions. Together with the unique properties of biocompatibility, permeability, and biodegradability, the hydrogel becomes an ideal biomaterial for 3D bioprinting to produce designable 3D constructs for applications in tissue engineering.     

Making JP‐10 Superfuel Affordable with a Lignocellulosic Platform Compound

The synthesis of renewable jet fuel from lignocellulosic platform compounds has drawn a lot of attention in recent years. So far, most work has concentrated on the production of conventional jet fuels. JP‐10 is an advanced jet fuel currently obtained from fossil energy. Due to its excellent properties, JP‐10 has been widely used in military aircraft. However, the high price and low availability limit its application in civil aviation. Here, we report a new strategy for the synthesis of bio‐JP‐10 fuel from furfuryl alcohol that is produced on an industrial scale from agricultural and forestry residues. Under the optimized conditions, bio‐JP‐10 fuel was produced with high overall carbon yields (≈65 %). A preliminary economic analysis indicates that the price of bio‐JP‐10 fuel can be greatly decreased from ≈7091 US$/ton (by fossil route) to less than 5600 US$/ton using our new strategy. This work makes the practical application of bio‐JP‐10 fuel forseeable.     

Simulation of novel soy protein‐based systems for tissue regeneration applications

In the present research, molecular modeling methods were used to study novel porous soy protein conjugates with gelatin or alginate, which were recently developed as potential scaffolds for tissue engineering applications. Gelatin (protein) and alginate (polysaccharides) were chemically crosslinked to soy protein isolates (SPI) in order to obtain a porous 3D network. Computational tools were applied to estimate the crosslinking degree and compare the degradation rate of soy–gelatin or soy–alginate conjugates. Soy protein 3D structure was obtained from the Protein Data Bank (PDB). Alginate and gelatin structures were built and subjected to dynamic simulation using the molecular modeling package Material Studio 7.0. The crosslinking degree was estimated by the miscibility of the two reactants and the interaction with the crosslinking agents 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide (EDC) or glyoxal. The calculations revealed that soy protein mixes well with gelatin but not with alginate. Radial distribution function (RDF) calculations showed that the interaction distance between alginate and EDC is significantly shorter than between gelatin and EDC, probably because of ionic attraction between the ammonium groups of EDC and the carboxylate groups in alginate, which facilitates the crosslinking reaction. The degradation rate of soy protein conjugates was related to their interaction with water. It was found that the solubility of soy–gelatin in water is higher than soy–alginate and that water molecules form more hydrogen bonds with soy–gelatin than with soy–alginate. These findings might be the reason for the observed difference in degradation rate of the two conjugates; the soy–gelatin degrades faster than soy–alginate. Copyright © 2016 John Wiley & Sons, Ltd.     

Development of Gelatin‐Alginate Hydrogels for Burn Wound Treatment

Hydrogels are interesting as wound dressing for burn wounds to maintain a moist environment. Especially gelatin and alginate based wound dressings show strong potential. Both polymers are modified by introducing photocrosslinkable functionalities and combined to hydrogel films (gel‐MA/alg‐MA). In one protocol gel‐MA films are incubated in alg‐MA solutions and crosslinked afterward into double networks. Another protocol involves blending both and subsequent photocrosslinking. The introduction of alginate into the gelatin matrix results in phase separation with polysaccharide microdomains in a protein matrix. Addition of alg(‐MA) to gel‐MA leads to an increased swelling compared to 100% gelatin and similar to the commercial Aquacel Ag dressing. In vitro tests show better cell adhesion for films which have a lower alginate content and also have superior mechanical properties. The hydrogel dressings exhibit good biocompatibility with adaptable cell attachment properties. An adequate gelatin‐alginate ratio should allow application of the materials as wound dressings for several days without tissue ingrowth.     

Nano‐Bio Engineered Carbon Dot‐Peptide Functionalized Water Dispersible Hyperbranched Polyurethane for Bone Tissue Regeneration

The present study delves into a combined bio‐nano‐macromolecular approach for bone tissue engineering. This approach relies on the properties of an ideal scaffold material imbued with all the chemical premises required for fostering cellular growth and differentiation. A tannic acid based water dispersible hyperbranched polyurethane is fabricated with bio‐nanohybrids of carbon dot and four different peptides (viz. SVVYGLR, PRGDSGYRGDS, IPP, and CGGKVGKACCVPTKLSPISVLYK) to impart target specific in vivo bone healing ability. This polymeric bio‐nanocomposite is blended with 10 wt% of gelatin and examined as a non‐invasive delivery vehicle. In vitro assessment of the developed polymeric system reveals good osteoblast adhesion, proliferation, and differentiation. Aided by this panel of peptides, the polymeric bio‐nanocomposite exhibits in vivo ectopic bone formation ability. The study on in vivo mineralization and vascularization reveals the occurrence of calcification and blood vessel formation. Thus, the study demonstrates carbon dot/peptide functionalized hyperbranched polyurethane gel for bone tissue engineering application.

     

pH‐Triggered Self‐Assembly of Cellulose Oligomers with Gelatin into a Double‐Network Hydrogel

Multicomponent systems for self‐assembled molecular gels provide huge opportunities to generate collective or new functions that are not inherent in individual single‐component gels. However, gelation tends to require careful and complicated procedures, because, among a myriad of kinetically trapped structures related to the degree of mixing of multiple components over a wide range of scales, from molecular level to macroscopic scale, a limited number of structures that exhibit the desired function need to be constructed. This study presents a simple method for the construction of double‐network (DN) hydrogels with improved stiffness composed of crystalline cellulose oligomers and gelatin. The pH‐triggered self‐assembly of cellulose oligomers leads to the formation of robust networks composed of crystalline nanofibers in the presence of dissolved gelatin, followed by cooling to allow for the formation of soft gelatin networks. The resultant DN hydrogels exhibit improved stiffness; the improvement in gel stiffness with double networking is comparable to that of previously reported DN hydrogels produced via a time‐consuming enzymatic reaction.     

A Spiderweb‐Like Metal–Organic Framework Multifunctional Foam

Processing metal–organic frameworks (MOFs) into hierarchical macroscopic materials can greatly extend their practical applications. However, current strategies suffer from severe aggregation of MOFs and limited tuning of the hierarchical porous network. Now, a strategy is presented that can simultaneously tune the MOF loading, composition, spatial distribution, and confinement within various bio‐originated macroscopic supports, as well as control the accessibility, robustness, and formability of the support itself. This method enables the good dispersion of individual MOF nanoparticles on a spiderweb‐like network within each macrovoid even at high loadings (up to 86 wt %), ensuring the foam pores are highly accessible for excellent adsorption and catalytic capacity. Additionally, this approach allows the direct pre‐incorporation of other functional components into the framework. This strategy provides precise control over the properties of both the hierarchical support and MOF.     

3D Bioprinting of Artificial Tissues: Construction of Biomimetic Microstructures

It is promising that artificial tissues/organs for clinical application can be produced via 3D bioprinting of living cells and biomaterials. The construction of microstructures biomimicking native tissues is crucially important to create artificial tissues with biological functions. For instance, the fabrication of vessel‐like networks to supply cells with initial nutrient and oxygen, and the arrangement of multiple types of cells for creating lamellar/complex tissues through 3D bioprinting are widely reported. The current advances in 3D bioprinting of artificial tissues from the view of construction of biomimetic microstructures, especially the fabrication of lamellar, vascular, and complex structures are summarized. In the end, the conclusion and perspective of 3D bioprinting for clinical applications are elaborated.     

Nanoarchitectonics beyond Self‐Assembly: Challenges to Create Bio‐Like Hierarchic Organization

Incorporation of non‐equilibrium actions in the sequence of self‐assembly processes would be an effective means to establish bio‐like high functionality hierarchical assemblies. As a novel methodology beyond self‐assembly, nanoarchitectonics, which has as its aim the fabrication of functional materials systems from nanoscopic units through the methodological fusion of nanotechnology with other scientific disciplines including organic synthesis, supramolecular chemistry, microfabrication, and bio‐process, has been applied to this strategy. The application of non‐equilibrium factors to conventional self‐assembly processes is discussed on the basis of examples of directed assembly, Langmuir–Blodgett assembly, and layer‐by‐layer assembly. In particular, examples of the fabrication of hierarchical functional structures using bio‐active components such as proteins or by the combination of bio‐components and two‐dimensional nanomaterials, are described. Methodologies described in this review article highlight possible approaches using the nanoarchitectonics concept beyond self‐assembly for creation of bio‐like higher functionalities and hierarchical structural organization.